CDD-564
File:
CDD-564.mib (82280 bytes)
Imported modules
Imported symbols
Defined Types
| Cdd564AccessListEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564AccessListIndex |
INTEGER |
|
| |
cdd564AccessIPAddress |
IpAddress |
|
| |
cdd564AccessSubnetMaskLength |
INTEGER |
|
| Cdd564FeaturesEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564FeatureIndex |
INTEGER |
|
| |
cdd564HeaderCompression |
INTEGER |
|
| Cdd5643xDESRxKeyEntry |
|
| SEQUENCE |
|
|
|
| |
cdd5643xDESRxKeyIndex |
INTEGER |
|
| |
cdd5643xDESRxKey1 |
DisplayString |
|
| |
cdd5643xDESRxKey2 |
DisplayString |
|
| |
cdd5643xDESRxKey3 |
DisplayString |
|
| |
cdd5643xDESRxKey4 |
DisplayString |
|
| |
cdd5643xDESRxKey5 |
DisplayString |
|
| |
cdd5643xDESRxKey6 |
DisplayString |
|
| |
cdd5643xDESRxKey7 |
DisplayString |
|
| |
cdd5643xDESRxKey8 |
DisplayString |
|
| Cdd564HDLCAddressEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564HDLCAddressIndex |
INTEGER |
|
| |
cdd564HDLCAddress1 |
INTEGER |
|
| |
cdd564HDLCAddress2 |
INTEGER |
|
| |
cdd564HDLCAddress3 |
INTEGER |
|
| |
cdd564HDLCAddress4 |
INTEGER |
|
| Cdd564RouteEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564RouteIndex |
INTEGER |
|
| |
cdd564RouteName |
DisplayString |
|
| |
cdd564RouteDestAddress |
IpAddress |
|
| |
cdd564RouteDestMaskLen |
INTEGER |
|
| |
cdd564RouteNextHopAddress |
IpAddress |
|
| |
cdd564RouteMulticast |
INTEGER |
|
| |
cdd564RouteInterface |
INTEGER |
|
| |
cdd564RouteRowStatus |
INTEGER |
|
| Cdd564IGMPEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564IGMPIndex |
INTEGER |
|
| |
cdd564IGMPTTL |
INTEGER |
|
| |
cdd564IGMPClientState |
INTEGER |
|
| |
cdd564IGMPSrc |
INTEGER |
|
| |
cdd564IGMPGroupIPAddress |
IpAddress |
|
| Cdd564SatelliteRxStatsEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564RxStatsIndex |
INTEGER |
|
| |
cdd564RxGoodFrames |
Counter32 |
|
| |
cdd564RxHeaderBytes |
Counter32 |
|
| |
cdd564RxPayloadBytes |
Counter32 |
|
| |
cdd564RxBadHDLCAddressErrors |
Counter32 |
|
| |
cdd564RxPktProcCRCErrors |
Counter32 |
|
| |
cdd564RxAbortOctetErrors |
Counter32 |
|
| |
cdd564RxOverrunErrors |
Counter32 |
|
| |
cdd564RxHDLCCRCErrors |
Counter32 |
|
| |
cdd564RxInvalidFlowIDErrors |
Counter32 |
|
| |
cdd564RxSARReassembleErrors |
Counter32 |
|
| |
cdd564RxHeaderDecompressionErrors |
Counter32 |
|
| |
cdd564RxMemoryAlignmentErrors |
Counter32 |
|
| |
cdd564RxCRCErrors |
Counter32 |
|
| Cdd564RxEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564RxTableIndex |
INTEGER |
|
| |
cdd564RxFEC |
INTEGER |
|
| |
cdd564RxDemodulation |
INTEGER |
|
| |
cdd564RxCodeRate |
INTEGER |
|
| |
cdd564RxDataRate |
INTEGER |
|
| |
cdd564RxFrequency |
INTEGER |
|
| |
cdd564RxAcquisitionSweepWidth |
INTEGER |
|
| |
cdd564RxDescrambling |
INTEGER |
|
| |
cdd564RxBufferSize |
INTEGER |
|
| |
cdd546RxSpectrumInversion |
INTEGER |
|
| |
cdd564RxDataInversion |
INTEGER |
|
| |
cdd564RxEbNoAlarmPoint |
INTEGER |
|
| |
cdd564RxRecenterBuffer |
INTEGER |
|
| |
cdd564RxSymbolRate |
INTEGER |
|
| Cdd564AlarmMaskEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564AlarmMaskIndex |
INTEGER |
|
| |
cdd564AGCAlarmMask |
INTEGER |
|
| |
cdd564EbNoAlarmMask |
INTEGER |
|
| |
cdd564LNBAlarmMask |
INTEGER |
|
| Cdd564LNBEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564LNBIndex |
INTEGER |
|
| |
cdd564LNBDCPower |
INTEGER |
|
| |
cdd564LNB10MHzReference |
INTEGER |
|
| |
cdm564LLNBLowCurrentLimit |
INTEGER |
|
| |
cdd564LNBHighCurrentLimit |
INTEGER |
|
| |
cdd564LNBLOFrequency |
INTEGER |
|
| |
cdd564LNBLOMix |
INTEGER |
|
| Cdd564RxMonitorEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564RxMonitorIndex |
INTEGER |
|
| |
cdd564RxAlarm |
INTEGER |
|
| |
cdd564RxEbNo |
INTEGER |
|
| |
cdd564RxSignalLevel |
INTEGER |
|
| |
cdd564RxFreqOffset |
INTEGER |
|
| |
cddRxBERMultiplier |
INTEGER |
|
| Cdd564LNBMonitorEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564LNBMonitorIndex |
INTEGER |
|
| |
cdd564LNBAlarm |
INTEGER |
|
| |
cdd564LNBCurrent |
INTEGER |
|
| |
cdd564LNBVoltage |
INTEGER |
|
| |
cdd564LNBTerminalRxFreq |
INTEGER |
|
| Cdd564StoredEventsEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564EventDemod |
INTEGER |
|
| |
cdd564EventIndex |
INTEGER |
|
| |
cdd564EventDescription |
DisplayString |
|
| Cdd564StoredStatisticsEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564StatisticDemod |
INTEGER |
|
| |
cdd564StatisticIndex |
INTEGER |
|
| |
cdd564StatisticDate |
DisplayString |
|
| |
cdd564StatisticTime |
DisplayString |
|
| |
cdd564StatisticAvgEbNo |
INTEGER |
|
| |
cdd564StatisticMinEbNo |
INTEGER |
|
| Cdd564StoredStatisticsConfigEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564StoredStatisticsConfigIndex |
INTEGER |
|
| |
cdd564StatisticsSampleInterval |
INTEGER |
|
| Cdd564CircuitIDEntry |
|
| SEQUENCE |
|
|
|
| |
cdd564CircuitIDIndex |
INTEGER |
|
| |
cdd564CircuitID |
DisplayString |
|
Defined Values
| cdd564 |
1.3.6.1.4.1.6247.25 |
| Module for CDD-564 Satellite Demod |
| MODULE-IDENTITY |
|
|
|
| cdd564AccessListEntry |
1.3.6.1.4.1.6247.25.1.1.1.1.1 |
| The entry for the access list table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564AccessListEntry |
|
|
| cdd564AccessListIndex |
1.3.6.1.4.1.6247.25.1.1.1.1.1.1 |
| The index for the access list from 1..4. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564AccessIPAddress |
1.3.6.1.4.1.6247.25.1.1.1.1.1.2 |
| The IP addresses that can access the unit.
The value of 0.0.0.0 means not defined. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| cdd564AccessSubnetMaskLength |
1.3.6.1.4.1.6247.25.1.1.1.1.1.3 |
| The subnet mask length of the IP address
for the access list. Subnet mask can be
from 8..32. The value of 0 means not defined. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0 | 8..32 |
|
| cdd564AccessListEnforcement |
1.3.6.1.4.1.6247.25.1.1.1.2 |
| Enable or disable enforcement of the the access
list.
Note: Be sure that you have added the SNMP
browser's/manager's IP Address to the access
list before enabling access list filtering.
Otherwise, the SNMP browser/manager will no
longer be able to gain access to the unit. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0), enabled(1) |
|
| cdd564PingReply |
1.3.6.1.4.1.6247.25.1.1.2.1 |
| Enable or disable ping reply from unit. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0), enabled(1) |
|
| cdd564Telnet |
1.3.6.1.4.1.6247.25.1.1.2.2 |
| Enable or disable telnet access to unit. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0), enabled(1) |
|
| cdd564IGMP |
1.3.6.1.4.1.6247.25.1.1.2.3 |
| Enable or disable the Internet Group Management
Protocol (IGMP). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0), enabled(1) |
|
| cdd564ForwardMulticasts |
1.3.6.1.4.1.6247.25.1.1.2.4 |
| Enable or disable forwarding all multicasts
received from the Satellite interface
to the Ethernet interface. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0), enabled(1) |
|
| cdd564FeaturesEntry |
1.3.6.1.4.1.6247.25.1.1.2.5.1 |
| The entry for the FAST Feature (per demod) table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564FeaturesEntry |
|
|
| cdd564FeatureIndex |
1.3.6.1.4.1.6247.25.1.1.2.5.1.1 |
| The index for the FAST Feature (per demod) table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564WorkingMode |
1.3.6.1.4.1.6247.25.1.1.2.6 |
| Configure the system's working mode.
The CDM-IP can operate in any of these modes.
1. Router - Small Network Mode - The system functions as router and
uses the route table to determine how to forward packets in a
small network HDLC address mode. The HDLC packet uses a 1 byte
HDLC address. The valid values are from 1 to 254 (0x1 - 0xFE).
2. Router - Small Network Mode - The system functions as router and
uses the route table to determine how to forward packets in a
large network HDLC address mode. The HDLC packet uses a 2- byte
HDLC address. The valid values are from 1 to 32766 (0x1 - 0x7FFE).
3. Router - Point To Point Mode - The system functions as router but
does not use HDLC addresses.
4. Router - Vipersat Mode - The system functions as router and is
configured to work in a Vipersat network.
*** IMPORTANT NOTE ***
Changing Working mode requires the system to reboot.
System configuration is saved before rebooting.
Please make sure you are setting the correct value.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
routerSmallNetworkMode(1), routerLargeNetworkMode(2), routerPointToPointMode(3), routerVipersatMode(4) |
|
| cdd5643xDESRxKeyEntry |
1.3.6.1.4.1.6247.25.1.1.3.1.1 |
| The entry (per demod) of the 3xDES receive
decrypt key table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd5643xDESRxKeyEntry |
|
|
| cdd5643xDESRxKeyIndex |
1.3.6.1.4.1.6247.25.1.1.3.1.1.1 |
| The index (per demod) of the 3xDES receive
decrypt key table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd5643xDESRxKey1 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.2 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey2 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.3 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey3 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.4 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey4 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.5 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey5 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.6 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey6 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.7 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey7 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.8 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd5643xDESRxKey8 |
1.3.6.1.4.1.6247.25.1.1.3.1.1.9 |
| The 3xDES receive decrypt key.
The key length is 192 bits
(24 bytes or 48 characters). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(48) |
|
| cdd564SMTP |
1.3.6.1.4.1.6247.25.1.1.4 |
| OBJECT IDENTIFIER |
|
|
|
| cdd564SMTPServerIPAddress |
1.3.6.1.4.1.6247.25.1.1.4.1 |
| The IP address of the SMTP server for sending
problem reports. This IP adderess should
correspond to a local Mail server. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| cdd564SMTPDomain |
1.3.6.1.4.1.6247.25.1.1.4.2 |
| The SMTP Domain for sending problem reports.
This value should be comtechefdata.com. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564SMTPUserName |
1.3.6.1.4.1.6247.25.1.1.4.3 |
| The user name for sending problem reports.
This value should be cdmipsupport. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564SNMP |
1.3.6.1.4.1.6247.25.1.1.5 |
| OBJECT IDENTIFIER |
|
|
|
| cdd564SNMPTrapDestinationIPAddress |
1.3.6.1.4.1.6247.25.1.1.5.1 |
| The IP address were SNMP notifications (traps)
are to be sent. This IP address should
correspond to a SNMP manager or browser. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| cdd564SNMPTrapVersion |
1.3.6.1.4.1.6247.25.1.1.5.3 |
| The SNMP version that will be used when sending
traps from the unit. SNMPv1 will send V1 traps.
SNMPv2 will send V2 notifications. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
snmpV1(1), snmpV2(2) |
|
| cdd564SNMPAuthenticationFailureIPAddress |
1.3.6.1.4.1.6247.25.1.1.5.5 |
| The IP address that did not send a valid SNMP
Read or Write community.
Note: This is ONLY used in the Authentication
Failure trap. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| cdd564SNMPTrapDestinationIPAddress2 |
1.3.6.1.4.1.6247.25.1.1.5.6 |
| The secondary IP address were SNMP notifications (traps)
are to be sent. This IP address should correspond
to a secondary SNMP manager or browser. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| cdd564MACAddress |
1.3.6.1.4.1.6247.25.1.2.1.1 |
| The MAC address assigned to the Ethernet
interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564EthernetSpeed |
1.3.6.1.4.1.6247.25.1.2.1.2 |
| The speed of the Ethernet interface. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
auto(1), halfDuplex10M(2), halfDuplex100M(3), fullDuplex10M(4), fullDuplex100M(5) |
|
| cdd564IPAddress |
1.3.6.1.4.1.6247.25.1.2.1.3 |
| The IP address assigned to the Ethernet
interface. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| cdd564SubnetMaskLen |
1.3.6.1.4.1.6247.25.1.2.1.4 |
| The subnet mask length of the IP address. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
8..30 |
|
| cdd564HDLCAddressMode |
1.3.6.1.4.1.6247.25.1.2.2.2 |
| The size of HDLC address used for sending
packets over satellite interface can range
from 0 - 2 bytes.
The satellite interface will operate in one of
the following modes:
1.Small Network mode - The packet uses a
1 byte HDLC address. The valid
values are from 1 to 254 (0x1 - 0xFE).
2.Large Network mode - The packet uses a 2
byte HDLC address. The valid values are
from 1 to 32766 (0x1 - 0x7FFE).
3. Point To Point mode - The packet does not use
a HDLC address.
An HDLC address cannot have 0x00 or 0xFF in
least Significant Byte. i.e., 0x400 or 0x6ff
or 0x11ff are NOT valid HDLC addresses.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
smallNetworkMode(1), largeNetworkMode(2), pointToPointMode(3) |
|
| cdd564HDLCAddressEntry |
1.3.6.1.4.1.6247.25.1.2.2.3.1 |
| The entry of the HDLC Address table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564HDLCAddressEntry |
|
|
| cdd564HDLCAddressIndex |
1.3.6.1.4.1.6247.25.1.2.2.3.1.1 |
| The Demod number corresponding to 1 of 4
demodulators. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564HDLCAddress1 |
1.3.6.1.4.1.6247.25.1.2.2.3.1.3 |
| The HDLC address #1 for the satellite
interface.
The valid values are:
1. Small network, 1 to 254 (0x1 - 0xFE).
2. Large network, 1 to 32766 (0x1 - 0x0x7FFE).
3. Point to point, not used.
4. EasyConnect, not used.
HDLC address can not have 0x00 or 0xFF
in least significant byte, i.e., 0x400 or
0x6ff or 0x11ff are NOT valid HDLC addresses.
Deletion:
To delete the HDLC address, set it to zero.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0 | 1..32766 |
|
| cdd564HDLCAddress2 |
1.3.6.1.4.1.6247.25.1.2.2.3.1.4 |
| The HDLC address #2 for the satellite
interface.
The valid values are:
1. Small network, 1 to 254 (0x1 - 0xFE).
2. Large network, 1 to 32766 (0x1 - 0x0x7FFE).
3. Point to point, not used.
4. EasyConnect, not used.
HDLC address can not have 0x00 or 0xFF
in least significant byte, i.e., 0x400 or
0x6ff or 0x11ff are NOT valid HDLC addresses.
Deletion:
To delete the HDLC address, set it to zero. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0 | 1..32766 |
|
| cdd564HDLCAddress3 |
1.3.6.1.4.1.6247.25.1.2.2.3.1.5 |
| The HDLC address #3 for the satellite
interface.
The valid values are:
1. Small network, 1 to 254 (0x1 - 0xFE).
2. Large network, 1 to 32766 (0x1 - 0x0x7FFE).
3. Point to point, not used.
4. EasyConnect, not used.
HDLC address can not have 0x00 or 0xFF
in least significant byte, i.e., 0x400 or
0x6ff or 0x11ff are NOT valid HDLC addresses.
Deletion:
To delete the HDLC address, set it to zero. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0 | 1..32766 |
|
| cdd564HDLCAddress4 |
1.3.6.1.4.1.6247.25.1.2.2.3.1.6 |
| The HDLC address #4 for the satellite
interface.
The valid values are:
1. Small network, 1 to 254 (0x1 - 0xFE).
2. Large network, 1 to 32766 (0x1 - 0x0x7FFE).
3. Point to point, not used.
4. EasyConnect, not used.
HDLC address can not have 0x00 or 0xFF
in least significant byte, i.e., 0x400 or
0x6ff or 0x11ff are NOT valid HDLC addresses.
Deletion:
To delete the HDLC address, set it to zero. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0 | 1..32766 |
|
| cdd564RouteEntry |
1.3.6.1.4.1.6247.25.1.3.1.1 |
| The entry for the the route table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564RouteEntry |
|
|
| cdd564RouteIndex |
1.3.6.1.4.1.6247.25.1.3.1.1.1 |
| The index for the route table. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..1024 |
|
| cdd564RouteName |
1.3.6.1.4.1.6247.25.1.3.1.1.2 |
| The name of the route. All routes must be
named. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564RouteDestMaskLen |
1.3.6.1.4.1.6247.25.1.3.1.1.4 |
| The subnet mask lenght for the destination IP
address. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..32 |
|
| cdd564RouteMulticast |
1.3.6.1.4.1.6247.25.1.3.1.1.6 |
| If the route is a multicast, packets can be:
1. forwarded
2. filtered
If the route is unicast, the field is not applicable. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notApplicable(0), forward(1), filtered(2) |
|
| cdd564RouteInterface |
1.3.6.1.4.1.6247.25.1.3.1.1.7 |
| Routes are destined to the Ethernet interface. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
toEthernet(2) |
|
| cdd564RouteRowStatus |
1.3.6.1.4.1.6247.25.1.3.1.1.8 |
| This value is used for status of route:
active(1) - The route is active.
These values are used to create or delete route:
createAndGo(4) - The route is to be created.
destroy(6) - The route to be deleted. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) |
|
| cdd564IGMPQueryPeriod |
1.3.6.1.4.1.6247.25.1.4.1.1.1 |
| The IGMP query period, in seconds. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..600 |
|
| cdd564IGMPMaxResponseTime |
1.3.6.1.4.1.6247.25.1.4.1.1.2 |
| The IGMP maximum response time, in seconds. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..600 |
|
| cdd564IGMPMaxMissBeforeLeavingGroup |
1.3.6.1.4.1.6247.25.1.4.1.1.3 |
| The maximum number of missed responses before
leaving the IGMP group. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..30 |
|
| cdd564IGMPEntry |
1.3.6.1.4.1.6247.25.1.4.1.3.1 |
| The entry for the IGMP group table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564IGMPEntry |
|
|
| cdd564IGMPIndex |
1.3.6.1.4.1.6247.25.1.4.1.3.1.1 |
| The index for the IGMP group table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..256 |
|
| cdd564IGMPTTL |
1.3.6.1.4.1.6247.25.1.4.1.3.1.2 |
| The TTL for the multicast group. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..255 |
|
| cdd564IGMPClientState |
1.3.6.1.4.1.6247.25.1.4.1.3.1.3 |
| The state for the multicast group. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
idle(1), active(2), closing(3) |
|
| cdd564IGMPSrc |
1.3.6.1.4.1.6247.25.1.4.1.3.1.4 |
| The interface from which the multicast group
was received. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ethernet(1), satellite(2) |
|
| cdd564Maint |
1.3.6.1.4.1.6247.25.1.5 |
| OBJECT IDENTIFIER |
|
|
|
| cdd564BootInfo |
1.3.6.1.4.1.6247.25.1.5.1.1 |
| The version and revision information for the
boot application. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564Bulk1Info |
1.3.6.1.4.1.6247.25.1.5.1.2 |
| The version and revision information for the
bulk application in image 1. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564Bulk2Info |
1.3.6.1.4.1.6247.25.1.5.1.3 |
| The version and revision information for the
bulk application in image 2. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564FPGARx1Info |
1.3.6.1.4.1.6247.25.1.5.1.4 |
| The version and revision information for the
Rx FPGA in image 1. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564FPGARx2Info |
1.3.6.1.4.1.6247.25.1.5.1.5 |
| The version and revision information for the
Rx FPGA in image 2. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564BootImage |
1.3.6.1.4.1.6247.25.1.5.2.1 |
| Specifies which image will be booted:
latest - boots the latest image determined by
the most recent build date
image 1 - boots image from bulk #1
image 2 - boots image from bulk #2 |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
latest(0), image1(1), image2(2) |
|
| cdd564UpgradeImage |
1.3.6.1.4.1.6247.25.1.5.2.2 |
| Specifies which image will be overwritten
during an upgrade:
oldest - overwrites the oldest image
determined by build date.
image 1 - overwrites image 1
image 2 - overwrites image 2
NOTE: Set this value before performing an
upgrade. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
oldest(0), image1(1), image2(2) |
|
| cdd564ParamImage |
1.3.6.1.4.1.6247.25.1.5.3.1 |
| Specifies if configuration should be read from:
paramFile - parameter file stored in flash
factoryDefaults - the factory defaults |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
paramFile(1), factoryDefaults(2) |
|
| cdd564SaveParamToFlash |
1.3.6.1.4.1.6247.25.1.5.3.2 |
| This is a SET command to save the
configuration to the parameter file
in flash. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
save(1) |
|
| cdd564ReloadParamFromFlash |
1.3.6.1.4.1.6247.25.1.5.3.3 |
| This is a SET command to reload the
configuration from the parameter
file in flash. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
reload(1) |
|
| cdd564RestoreFactoryDefaults |
1.3.6.1.4.1.6247.25.1.5.3.4 |
| This is a SET command that restore the
configuration to the factory defaults.
*** Imporant ***
Setting this command ERASES the parameter
file in flash. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
restore(1) |
|
| cdd564Reboot |
1.3.6.1.4.1.6247.25.1.5.4.1 |
| The is a SET command that will reboot the unit.
*** Important ***
The command will reboot the unit without
saving the configuration to the parameter file
in flash. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
reboot(1) |
|
| cdd564TotalPacketsFromEndstation |
1.3.6.1.4.1.6247.25.1.6.1.3.1 |
| The total number of packets received from the
Endstation to be sent out one of the
interfaces. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564TotalPacketsToEndstation |
1.3.6.1.4.1.6247.25.1.6.1.3.2 |
| The total number of packets sent to the
Endstation from one of the interfaces. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564IGMPPacketsReceived |
1.3.6.1.4.1.6247.25.1.6.1.4.1 |
| The total number of IGMP packets received by
the endstation. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564DroppedPacketsBadIPVersion |
1.3.6.1.4.1.6247.25.1.6.1.5.4 |
| The total number of packets dropped by
the router because of the packet is
not IPv4.
Note: IPv6 packets are not support by
the router. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564DroppedPacketsTTLExpired |
1.3.6.1.4.1.6247.25.1.6.1.5.5 |
| The total number of packets dropped by
the router because the TTL (time to live)
in the IP header had expired
(i.e. reached zero). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564DroppedPacketsNoRoute |
1.3.6.1.4.1.6247.25.1.6.1.5.6 |
| The total number of packets dropped by
the router because the packet did not
match any route in the route table
and could not be forwarded. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564DroppedPacketsNoARPEntry |
1.3.6.1.4.1.6247.25.1.6.1.5.7 |
| The total number of packets dropped by
the router because the ARP table did
not have an ARP entry for the packet's
next hop. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564DroppedPacketsFilteredMulticast |
1.3.6.1.4.1.6247.25.1.6.1.5.8 |
| The total number of multicast packets dropped
by the router because the multicast address
is not being forwarded. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564DroppedPacketsFiltered |
1.3.6.1.4.1.6247.25.1.6.1.5.10 |
| The total number of packets dropped by the
router for the following reasons:
1. Boot
2. Flow Descriptor
3. Unknown Reason Code
4. Flow Correlator
5. Management Path
6. Ping
7. Access Control
8. Vipersat Multicommand
9. Vipersat Unicommand
10. Codeload
11. Multicast
12. Bad Packet
13. Route
14. Bad Header Len
15. Bad Data Ptr
16. MAC Split Err
17. L3Type Err
18. Local Destination
19. ICMP Filter
20. Port Err
21. Per port route rule |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564IPRoutingClearCounters |
1.3.6.1.4.1.6247.25.1.6.1.6 |
| This is a SET command to clear the IP routing
counters. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
clear(1) |
|
| cdd564EtherTxGoodFrames |
1.3.6.1.4.1.6247.25.1.6.2.1.1 |
| The number of transmitted good frames from
the Ethernet interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxMaxCollisions |
1.3.6.1.4.1.6247.25.1.6.2.1.2 |
| The number of frames that were NOT transmitted
because they encountered the maximum configured
collisions. This counter should only increment
when network is heavily saturated with traffic. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxLateCollisions |
1.3.6.1.4.1.6247.25.1.6.2.1.3 |
| The number of frames that were NOT transmitted
because they encountered collision outside
the normal collision window. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxDMAUnderrun |
1.3.6.1.4.1.6247.25.1.6.2.1.4 |
| The number of frames that were either NOT
transmitted or retransmitted due to Transmit
DMA underrun. Underruns occur due to lack of
PCI bandwidth resulting in the internal
transmit FIFO running dry during the
transmission of a frame. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxLostCarrierSense |
1.3.6.1.4.1.6247.25.1.6.2.1.5 |
| The number of frames transmitted by the device
despite the fact that it detected the
de-assertion of Transmit Lost Carrier Sense
(CRS) during the transmission.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxDeferred |
1.3.6.1.4.1.6247.25.1.6.2.1.6 |
| The number of frames deferred before
transmission due to activity on the link. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxTotalCollisions |
1.3.6.1.4.1.6247.25.1.6.2.1.9 |
| The total number of collisions that were
encountered while attempting to transmit. This
count includes late collisions and collisions
from frames that encountered maximum
collisions. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherTxFlowControlPauseFrames |
1.3.6.1.4.1.6247.25.1.6.2.1.10 |
| The number of flow control frames transmitted
by the device. This count includes both the
XOFF and XON frames transmitted by the device. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherRxGoodFrames |
1.3.6.1.4.1.6247.25.1.6.2.2.1 |
| The number of frames properly received from the
link. It is updated only after actual reception
from the link is completed and all data bytes
are stored in memory. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherRxAllignmentErrors |
1.3.6.1.4.1.6247.25.1.6.2.2.3 |
| The number of frames that are both misaligned
[in other words, CRS de-asserts on a non-octet
boundary] and contain a CRC error. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherRxFIFOOverrunErrors |
1.3.6.1.4.1.6247.25.1.6.2.2.5 |
| The number of frames known to be lost because
the internal receive FIFO overflowed [also
known as receive overrun]. This can occur if
the device is unable to get necessary PCI
bandwidth. If the overflow condition persists
for more than one frame, the frames that
follow the first can also be lost.
A frame that was counted as an overrun will
not be counted in other error counters like
(short frames, misaligned, CRC error). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherRxShortFrames |
1.3.6.1.4.1.6247.25.1.6.2.2.7 |
| The number of received frames that are shorter
than the minimum frame length. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EtherRxFlowControlPauseFrames |
1.3.6.1.4.1.6247.25.1.6.2.2.8 |
| The number of flow control frames received by
the device. This count includes both XOFF and
XON frames received. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564EthernetClearCounters |
1.3.6.1.4.1.6247.25.1.6.2.3 |
| Reset all ethernet transmit & receive counters. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
clear(1) |
|
| cdd564SatelliteRxStatsEntry |
1.3.6.1.4.1.6247.25.1.6.3.1.1 |
| The entry for the Satellite interface
statistics table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564SatelliteRxStatsEntry |
|
|
| cdd564RxStatsIndex |
1.3.6.1.4.1.6247.25.1.6.3.1.1.1 |
| The Rx index for the satellite interface,
where index can be from 1 to 4. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564RxGoodFrames |
1.3.6.1.4.1.6247.25.1.6.3.1.1.2 |
| The total number of good frames received over
satellite interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxPayloadBytes |
1.3.6.1.4.1.6247.25.1.6.3.1.1.4 |
| The count of payload bytes that were received
over satellite interface, excluding any frame
overhead. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxBadHDLCAddressErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.5 |
| The count of received frames that did not match
any of the Rx HDLC addresses. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxPktProcCRCErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.6 |
| The Packet Processor CRC check is the second
CRC check performed after the HDLC CRC check.
It is the checksum calculated after Decryption
and Payload Decompression. Failures due to
3xDES and Payload Comp are detected at
this level.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxAbortOctetErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.7 |
| The count of aborted frames and octet error
frames.
Aborted frame:
A frame is aborted when the frame is not
complete and is terminated prematurely with
the Abort signal, which is 8 consecutive '1's.
Octet error:
A frames that was not on a byte boudary or on
a multiple of 8-bit boundary. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxOverrunErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.8 |
| The count of received frames that exceeded the
maximum frame length of 2K bytes or overflowed
the buffer which stores complete HDLC frames. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxHDLCCRCErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.9 |
| The HDLC CRC is the first stage of the CRC
check, before 3xDES and paylod Decompression.
It indicates any errors due to the satellite
link only. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxInvalidFlowIDErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.10 |
| The number of frames received where the flow
ID did not match to a valid flow descriptor. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxSARReassembleErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.11 |
| The number of frames corresponding to a packet
which had undergone segmentation and
encountered an error in reassembly. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxMemoryAlignmentErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.13 |
| The number of frames which were incorrectly
transferred (frame too small) from the Rx FPGA. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564RxCRCErrors |
1.3.6.1.4.1.6247.25.1.6.3.1.1.14 |
| The number of frames with a CRC error detected
by the Rx FPGA. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| cdd564SatelliteClearCounters |
1.3.6.1.4.1.6247.25.1.6.3.2 |
| This is a SET command for clearing all the
Satellite statistic counters. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
clear(1) |
|
| cdd564Rx |
1.3.6.1.4.1.6247.25.1.7.1 |
| OBJECT IDENTIFIER |
|
|
|
| cdd564RxTable |
1.3.6.1.4.1.6247.25.1.7.1.1 |
| The table of Demodulators. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
Cdd564RxEntry |
|
| cdd564RxEntry |
1.3.6.1.4.1.6247.25.1.7.1.1.1 |
| The entry for the Demodulator table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564RxEntry |
|
|
| cdd564RxTableIndex |
1.3.6.1.4.1.6247.25.1.7.1.1.1.1 |
| The index for the Rx table,
where index can be from 1 to 4. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564RxFEC |
1.3.6.1.4.1.6247.25.1.7.1.1.1.2 |
| Rx FEC type where:
0 = Uncoded
6 = Turbo |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
uncoded(0), turbo(6) |
|
| cdd564RxDemodulation |
1.3.6.1.4.1.6247.25.1.7.1.1.1.3 |
| Rx demodulation type, where:
1 = QPSK
3 = 8-PSK
4 = 16-QAM |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
demodQPSK(1), demod8PSK(3), demod16QAM(4) |
|
| cdd564RxCodeRate |
1.3.6.1.4.1.6247.25.1.7.1.1.1.4 |
| Rx code rate, where
4 = Rate 3/4
5 = Rate 7/8
6 = Rate 0.95
7 = Rate 1/1 (Uncoded) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
rate3over4(4), rate7over8(5), rate095(6), uncoded(7) |
|
| cdd564RxDataRate |
1.3.6.1.4.1.6247.25.1.7.1.1.1.5 |
| Rx data rate in bps (Varies based on chart below.)
Units = bps
Resolution = 1 bps
FEC Type Modulation Code Rate Data Rate High Rate
-------- ----------- ---------- --------------------- ---------
Turbo QPSK Rate 3/4 16.0 Kbps to 4.5 Mbps N/A
Turbo QPSK Rate 7/8 16.0 Kbps to 5.0 Mbps 5.25 Mbps
Turbo QPSK Rate 0.95 16.0 Kbps to 5.0 Mbps 5.667 Mbps
Turbo 8-PSK Rate 3/4 16.0 Kbps to 5.0 Mbps 6.75 Mbps
Turbo 8-PSK Rate 7/8 16.0 Kbps to 5.0 Mbps 7.875 Mbps
Turbo 8-PSK Rate 0.95 16.0 Kbps to 5.0 Mbps 8.5 Mbps
Turbo 16-QAM Rate 3/4 16.0 Kbps to 5.0 Mbps 9.0 Mbps
Turbo 16-QAM Rate 7/8 16.8 Kbps to 5.0 Mbps 9.98 Mbps |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
16000..9980000 |
|
| cdd564RxFrequency |
1.3.6.1.4.1.6247.25.1.7.1.1.1.6 |
| Rx frequency for L-Band and IF-Band modes.
L-Band is 950 MHz to 1950 MHz.
IF-Band is 50 MHz to 90 MHz and 100 MHz to 180 MHz.
Units = Hz.
Resolution = 100 Hz. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
50000000..90000000 | 100000000..180000000 | 950000000..1950000000 |
|
| cdd564RxAcquisitionSweepWidth |
1.3.6.1.4.1.6247.25.1.7.1.1.1.7 |
| Rx +/- acquisition sweep range of demodulator,
in KHz, ranging from:
+/- 1 to +/- 32 KHz (rates < 625 ksym/second)
or +/- 1 to 200 KHz (rates >= 625 ksym/second) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..200 |
|
| cdd564RxDescrambling |
1.3.6.1.4.1.6247.25.1.7.1.1.1.8 |
| Rx descrambler state, where:
0 = Off
1 = On (default descrambler type)
2 = On - IESS-315 (Turbo only) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
off(0), onDefault(1), onIESS315(2) |
|
| cdd564RxBufferSize |
1.3.6.1.4.1.6247.25.1.7.1.1.1.9 |
| Rx buffer size, where:
0 = Buffer disabled (Clock mode = Rx satellite) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0) |
|
| cdd546RxSpectrumInversion |
1.3.6.1.4.1.6247.25.1.7.1.1.1.10 |
| Rx spectrum inversion, where:
0 = Normal
1 = Rx spectrum inverted |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
normal(0), inverted(1) |
|
| cdd564RxDataInversion |
1.3.6.1.4.1.6247.25.1.7.1.1.1.11 |
| Invert receive data, where:
0 = Normal
1 = Inverted |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
normal(0), inverted(1) |
|
| cdd564RxEbNoAlarmPoint |
1.3.6.1.4.1.6247.25.1.7.1.1.1.12 |
| Rx Eb/No alarm point in 0.1 dB, with a range
between 0.1 dB and 16 dB.
Units = 0.1 dB
Resolution = 0.1 dB |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..160 |
|
| cdd564RxRecenterBuffer |
1.3.6.1.4.1.6247.25.1.7.1.1.1.13 |
| This is a SET command that recenters the
receive Plesiochronous/Doppler buffer. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
recenter(1) |
|
| cdd564RxSymbolRate |
1.3.6.1.4.1.6247.25.1.7.1.1.1.14 |
| Rx symbol rate in symbols per second (sym)
Units = sym
Resolution = 1 sym |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
5000..3000000 |
|
| cdd564AlarmMaskEntry |
1.3.6.1.4.1.6247.25.1.7.2.1.1 |
| Description. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564AlarmMaskEntry |
|
|
| cdd564AlarmMaskIndex |
1.3.6.1.4.1.6247.25.1.7.2.1.1.1 |
| The index for the Demodulator. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564AGCAlarmMask |
1.3.6.1.4.1.6247.25.1.7.2.1.1.2 |
| Rx AGC alarm mask, where:
0 = Unmasked
1 = Masked |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(0), masked(1) |
|
| cdd564EbNoAlarmMask |
1.3.6.1.4.1.6247.25.1.7.2.1.1.3 |
| Eb/No alarm mask, where:
0 = Unmasked
1 = Masked |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(0), masked(1) |
|
| cdd564LNBAlarmMask |
1.3.6.1.4.1.6247.25.1.7.2.1.1.5 |
| LNB alarm mask, where:
0 = Unmasked
1 = Masked |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(0), masked(1) |
|
| cdd564ReferenceFrequency |
1.3.6.1.4.1.6247.25.1.7.3.1 |
| External reference frequency, where:
0 = Internal 10 MHz |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
int10MHz(0) |
|
| cdd564InternalReferenceAdjust |
1.3.6.1.4.1.6247.25.1.7.3.2 |
| Internal Reference Adjust, from -999 to +999.
Units = KHz |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
-999..999 |
|
| cdd564LNB |
1.3.6.1.4.1.6247.25.1.7.4 |
| OBJECT IDENTIFIER |
|
|
|
| cdd564LNBTable |
1.3.6.1.4.1.6247.25.1.7.4.1 |
| The table for LNBs. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
Cdd564LNBEntry |
|
| cdd564LNBEntry |
1.3.6.1.4.1.6247.25.1.7.4.1.1 |
| The entry for the LNBs table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564LNBEntry |
|
|
| cdd564LNBIndex |
1.3.6.1.4.1.6247.25.1.7.4.1.1.1 |
| The index for the LNB.. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564LNBDCPower |
1.3.6.1.4.1.6247.25.1.7.4.1.1.2 |
| LNB power control, where:
0 = Off
1 = On, 13V LNB voltage
2 = On, 18V LNB voltage
3 = On, 24V LNB voltage |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
off(0), on13volts(1), on18volts(2), on24volts(3) |
|
| cdd564LNB10MHzReference |
1.3.6.1.4.1.6247.25.1.7.4.1.1.3 |
| LNB 10MHz frequency reference, where:
0 = Disable LNB 10MHz reference
1 = Enable LNB 10MHz reference |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(0), enable(1) |
|
| cdm564LLNBLowCurrentLimit |
1.3.6.1.4.1.6247.25.1.7.4.1.1.4 |
| LNB lower alarm limit for current, between
10 and 400 mA. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
10..400 |
|
| cdd564LNBHighCurrentLimit |
1.3.6.1.4.1.6247.25.1.7.4.1.1.5 |
| LNB upper alarm limit for current, between
50 and 600 mA. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
50..600 |
|
| cdd564LNBLOFrequency |
1.3.6.1.4.1.6247.25.1.7.4.1.1.6 |
| LNB receieve LO frequency, in the range of
3000 to 65000 MHz.
Setting a 0 disables the feature.
Terminal Frequency = LNB_LO +/- Rx_Frequency
(depending on High/Low Mix) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0 | 3000..65000 |
|
| cdd564LNBLOMix |
1.3.6.1.4.1.6247.25.1.7.4.1.1.7 |
| LO frequency mix, where:
0 = Low-side mix
1 = High-side mix |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
lowSideMix(0), highSideMix(1) |
|
| cdd564SoftwareRevision |
1.3.6.1.4.1.6247.25.1.8.1.2 |
| Unit returns the value of the internal
software revision installed in the unit,
in the form of x.x.x. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564ModelNumber |
1.3.6.1.4.1.6247.25.1.8.1.3 |
| Unit's model number. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..999 |
|
| cdd564UnitAlarm |
1.3.6.1.4.1.6247.25.1.8.1.4 |
| Modem Unit Faults:
Value Description of unit fault
0 No faults
1 +5 Volt power supply
2 +12 Volt power supply
3 -5 Volt power supply
4 +23 Volt power supply
5 -12 Volt power supply
6 Rx 1st LO synthesize lock
7 Rx 2nd LO synthesize lock
8 Ref PLL lock
9 EEPROM checksum error
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noFaults(0), powerSupply5volts(1), powerSupply12volts(2), powerSupplyNeg5volts(3), powerSupply23volts(4), powerSupplyNeg12volts(5), rx1stLOSynthesizerLock(6), rx2ndLOSynthesizerLock(7), refPLLLock(8), checksumErrorEEPROM(9) |
|
| cdd564Temperature |
1.3.6.1.4.1.6247.25.1.8.1.5 |
| Unit returns the value of the internal
temperature, in degrees Celsius. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
-99..99 |
|
| cdd564RxMonitorEntry |
1.3.6.1.4.1.6247.25.1.8.2.1.1 |
| The entry for the demoduator monitor table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564RxMonitorEntry |
|
|
| cdd564RxMonitorIndex |
1.3.6.1.4.1.6247.25.1.8.2.1.1.1 |
| The index for the demodulator monitor table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564RxAlarm |
1.3.6.1.4.1.6247.25.1.8.2.1.1.2 |
| Modem RX Traffic Faults
Value Description of status parameter
0 Rx Traffic OK
1 Demodulator unlocked
3 AGC Alarm - signal out of range
10 Buffer underflow
11 Buffer overflow
13 Eb/No alarm
15 AIS detected on incoming data |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
rxTrafficOK(0), demodulatorUnlocked(1), agcAlarmSignalOutOfRange(3), bufferUnderflow(10), bufferOverflow(11), ebNoAlarm(13), aisDetectedOnIncomingData(15) |
|
| cdd564RxEbNo |
1.3.6.1.4.1.6247.25.1.8.2.1.1.3 |
| Unit returns the value of Eb/No, between
0 and 16 db.
Units = 0.1 dB
Resolution 0.1 dB
Returns 999 if demod is unlocked.
For values greater than 16 dB, the reply
will be 160. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..160 | 999 |
|
| cdd564RxSignalLevel |
1.3.6.1.4.1.6247.25.1.8.2.1.1.4 |
| Unit returns the value of the Rx signal level,
in dBm, between -20 and -99 dBm,
Returns -100 if signal is less than -99dBm.
Returns -19 if signal is greater than -20dBm. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
-100 | -99..-20 | -19 |
|
| cdd564RxFreqOffset |
1.3.6.1.4.1.6247.25.1.8.2.1.1.5 |
| Unit returns the value of the measured
frequency offset of the carrier being
demodulated in Hz.
Units = Hz.
Resolution 100 Hz.
Range = -200,000 Hz to 0 Hz and
0 Hz to 200,000 Hz.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
-200000..200000 | 999900 |
|
| cddRxBERMultiplier |
1.3.6.1.4.1.6247.25.1.8.2.1.1.7 |
| Estimated corrected BER. The BER is calculated
by multiplying the Multiplier by 10E-10.
Calculuation:
RxBER = (Multiplier) * 0.0000000001
Returns 2147483647 (max int) if demod is
unlocked.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..999999999 | 2147483647 |
|
| cdd564LNBMonitorEntry |
1.3.6.1.4.1.6247.25.1.8.3.1.1 |
| The entry for the LNBs monitoring table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564LNBMonitorEntry |
|
|
| cdd564LNBMonitorIndex |
1.3.6.1.4.1.6247.25.1.8.3.1.1.1 |
| The index for the LNBs monitoring table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564LNBAlarm |
1.3.6.1.4.1.6247.25.1.8.3.1.1.2 |
| LNB alarms
Value Description of status parameter
0 No LNB faults
7 LNB current
9 LNB voltage |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noLNBfaults(0), lnbCurrent(7), lnbVoltage(9) |
|
| cdd564LNBCurrent |
1.3.6.1.4.1.6247.25.1.8.3.1.1.3 |
| Indicates the value of the LNB current,
between 0 and 999 mA. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..999 |
|
| cdd564LNBVoltage |
1.3.6.1.4.1.6247.25.1.8.3.1.1.4 |
| Indicates the value of the LNB voltage,
between 0 and 30 volts.
Units = 0.1 volts
If not available, response is 0. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..300 |
|
| cdd564LNBTerminalRxFreq |
1.3.6.1.4.1.6247.25.1.8.3.1.1.5 |
| Terminal Rx frequency = LNB LO +/- Rx_Frequency
(depending on LO mix)
Units = 100 Hz
Resolution = 100 Hz
Returns 0 if LNB_LO is zero. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..999999999 |
|
| cdd564StoredEventsEntry |
1.3.6.1.4.1.6247.25.1.8.4.1.1 |
| The entry for stored events table for all 4 demods. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564StoredEventsEntry |
|
|
| cdd564EventDemod |
1.3.6.1.4.1.6247.25.1.8.4.1.1.1 |
| The demodulator index for which event log is
being returned. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564EventIndex |
1.3.6.1.4.1.6247.25.1.8.4.1.1.2 |
| The index for a demod's stored events table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..255 |
|
| cdd564EventDescription |
1.3.6.1.4.1.6247.25.1.8.4.1.1.3 |
| Event description string with the following format
seprated by commas:
1. Date
in form dd/mm/yy, where:
dd = day of the month (01 to 31)
mm = month (01 to 12)
yy = year (00 to 99)
2. Time
in form hh:mm:ss, where:
hh = hours (00 to 23)
mm = minutes (00 to 59)
ss = seconds (00 to 59)
3. Event Type
in form xxxxx, where xxxxx is
Clear = fault cleared
Fault = fault occurred
Info = information
4. Texual Description of Event |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564ClearAllStoredEvents |
1.3.6.1.4.1.6247.25.1.8.4.2 |
| This is a SET command to clear the event log for
one of the four demods (1 - 4). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564StoredStatisticsEntry |
1.3.6.1.4.1.6247.25.1.8.5.1.1 |
| The entry for stored statistics table for all
four demods. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564StoredStatisticsEntry |
|
|
| cdd564StatisticDemod |
1.3.6.1.4.1.6247.25.1.8.5.1.1.1 |
| The demod index for which statistics table
is being returned. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564StatisticIndex |
1.3.6.1.4.1.6247.25.1.8.5.1.1.2 |
| The index in one of the four demod's stored
statistics table. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..255 |
|
| cdd564StatisticDate |
1.3.6.1.4.1.6247.25.1.8.5.1.1.3 |
| The date of the statistic in the
form dd/mm/yy, where:
dd = day of the month (01 to 31)
mm = month (01 to 12)
yy = year (00 to 99) |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564StatisticTime |
1.3.6.1.4.1.6247.25.1.8.5.1.1.4 |
| The time of the statistic in the form hh:mm:ss,
indicating the time from midnight, where:
hh = hours (00 to 23)
mm = minutes (00 to 59)
ss = seconds (00 to 59) |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564StatisticAvgEbNo |
1.3.6.1.4.1.6247.25.1.8.5.1.1.5 |
| Minimum Eb/No during sample period.
Units = 0.1 dB.
Returns 999 if demod was unlocked
during sample period. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..160 | 999 |
|
| cdd564StatisticMinEbNo |
1.3.6.1.4.1.6247.25.1.8.5.1.1.6 |
| Minimum Eb/No during sample period.
Units = 0.1 dB.
Returns 999 if demod was unlocked
during sample period. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..160 | 999 |
|
| cdd564StoredStatisticsConfigEntry |
1.3.6.1.4.1.6247.25.1.8.5.2.1 |
| The entry for the stored statistics configuration table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564StoredStatisticsConfigEntry |
|
|
| cdd564StatisticsSampleInterval |
1.3.6.1.4.1.6247.25.1.8.5.2.1.2 |
| Used to set the sample interval for the
statistics logging function, where the
enumerated lists goes from 0 to 9 in
10 minute steps.
Setting 0 disables the statistics logging
function.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(0), mins10(1), mins20(2), mins30(3), mins40(4), mins50(5), mins60(6), mins70(7), mins80(8), mins90(9) |
|
| cdd564ClearAllStoredStatistics |
1.3.6.1.4.1.6247.25.1.8.5.3 |
| This is a SET command to clear the statistics
log for one of the four demods (1 - 4). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564Util |
1.3.6.1.4.1.6247.25.1.9 |
| OBJECT IDENTIFIER |
|
|
|
| cdd564RTCDate |
1.3.6.1.4.1.6247.25.1.9.4 |
| A date in the form dd/mm/yy, where
dd = day of the month (01 to 31)
mm = month (01 to 12)
yy = year (00 to 99) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564RTCTime |
1.3.6.1.4.1.6247.25.1.9.5 |
| A time in the form hh:mm:ss, indicating the
time from midnight, where:
hh = hours (00 to 23)
mm = minutes (00 to 59)
ss = seconds (00 to 59) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564CircuitIDEntry |
1.3.6.1.4.1.6247.25.1.9.6.1 |
| The entry for the circuit ID table. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cdd564CircuitIDEntry |
|
|
| cdd564CircuitIDIndex |
1.3.6.1.4.1.6247.25.1.9.6.1.1 |
| The index for the Demodulator. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4 |
|
| cdd564CircuitID |
1.3.6.1.4.1.6247.25.1.9.6.1.2 |
| Sets or queries the user-defined Circuit
ID string, which is a fixed length of
24 characters.
Valid characters include:
Space ( ) * + - , . / 0 thru 9 and A thru Z. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| cdd564ObjectsGroup |
1.3.6.1.4.1.6247.25.3.1.1 |
| CDD-564 Objects Group. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| cdd564NotificationsGroup |
1.3.6.1.4.1.6247.25.3.1.2 |
| CDD-564 Trap Group. |
| Status: current |
Access: read-write |
| NOTIFICATION-GROUP |
|
|
|
| cdd564Compliance |
1.3.6.1.4.1.6247.25.3.2.1 |
| CDD-564 Compliance. |
| Status: current |
Access: read-write |
| MODULE-COMPLIANCE |
|
|
|