BAY-STACK-NOTIFICATIONS-MIB

File: BAY-STACK-NOTIFICATIONS-MIB.mib (22450 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SYNOPTICS-ROOT-MIB
IEEE8021-PAE-MIB IF-MIB INET-ADDRESS-MIB
SNMP-FRAMEWORK-MIB BAY-STACK-MIB S5-CHASSIS-MIB
S5-AGENT-MIB

Imported symbols

MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
Integer32 MacAddress DisplayString
bayStackMibs dot1xAuthPaeState dot1xAuthBackendAuthState
ifIndex ifAdminStatus InetAddressType
InetAddress SnmpAdminString bayStackConfigExpectedStackSize
bayStackUnitConfigIndex s5ChasComType InterfaceIndex
s5AgSysUsbTargetUnit s5AgentScriptStatus

Defined Values

bayStackNotificationsMib 1.3.6.1.4.1.45.5.2
Miscellaneous NOTIFICATION definitions for BayStack products.
MODULE-IDENTITY    

bsnObjects 1.3.6.1.4.1.45.5.2.1
OBJECT IDENTIFIER    

bsnNotifications 1.3.6.1.4.1.45.5.2.2
OBJECT IDENTIFIER    

bsnNotifications0 1.3.6.1.4.1.45.5.2.2.0
OBJECT IDENTIFIER    

bsnEapAccessViolationMacAddress 1.3.6.1.4.1.45.5.2.1.1
The MAC address which caused an EAP access violation.
OBJECT-TYPE    
  MacAddress  

bsnLoginFailureType 1.3.6.1.4.1.45.5.2.1.2
The type of login being attempted when the failure occurred.
OBJECT-TYPE    
  INTEGER telnet(1), ssh(2), web(3), serialConsole(4)  

bsnLoginFailureAddressType 1.3.6.1.4.1.45.5.2.1.3
The address type contained in the associated value of bnsLoginFailureAddress.
OBJECT-TYPE    
  InetAddressType  

bsnLoginFailureAddress 1.3.6.1.4.1.45.5.2.1.4
The IP address from which the login was attempted when the failure occurred.
OBJECT-TYPE    
  InetAddress  

bsnLoginFailureUsername 1.3.6.1.4.1.45.5.2.1.5
The username for which the login failure occurred.
OBJECT-TYPE    
  SnmpAdminString  

bsnActualStackSize 1.3.6.1.4.1.45.5.2.1.6
The actual stack size when a bsnStackConfigurationError notification is generated.
OBJECT-TYPE    
  Integer32 1..8  

bsnEapUbpFailureIfIndex 1.3.6.1.4.1.45.5.2.1.7
The ifIndex of the port for which UBP policies could not be installed.
OBJECT-TYPE    
  InterfaceIndex  

bsnEapUbpFailureMacAddress 1.3.6.1.4.1.45.5.2.1.8
The MAC address for which UBP policies could not be installed.
OBJECT-TYPE    
  MacAddress  

bsnEapUbpFailureRoleString 1.3.6.1.4.1.45.5.2.1.9
The role string of the UBP policies which could not be installed.
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

bsnTrialLicenseExpirationTime 1.3.6.1.4.1.45.5.2.1.10
The number of days until a feature trial license will expire. A value of 0 means the license has expired.
OBJECT-TYPE    
  Integer32 0..30  

bsnTrialLicenseExpirationNumber 1.3.6.1.4.1.45.5.2.1.11
The number of the license that will expire or that has expired.
OBJECT-TYPE    
  Integer32 1..10  

bsnEnteredForcedStackModeMAC 1.3.6.1.4.1.45.5.2.1.12
The MAC address of a switch which has entered forced stack mode.
OBJECT-TYPE    
  MacAddress  

bsnEapRAVErrorMacAddress 1.3.6.1.4.1.45.5.2.1.13
The MAC address that was authorized on a port which could not be moved to the Radius-Assigned VLAN.
OBJECT-TYPE    
  MacAddress  

bsnEapRAVErrorPort 1.3.6.1.4.1.45.5.2.1.14
The ifIndex of the port that could not be moved to the Radius-Assigned VLAN.
OBJECT-TYPE    
  InterfaceIndex  

bsnEnteredForcedStackModeAddressType 1.3.6.1.4.1.45.5.2.1.15
The address type contained in the associated value of bsnEnteredForcedStackModeAddress.
OBJECT-TYPE    
  InetAddressType  

bsnEnteredForcedStackModeAddress 1.3.6.1.4.1.45.5.2.1.16
The IP address in use on the switch that entered forced stack mode.
OBJECT-TYPE    
  InetAddress  

bsnStackProtectionEvent 1.3.6.1.4.1.45.5.2.1.17
This object specifies the Stack Protection events which may occur. cannotJoinStack(1) occurs on a BU (base unit) enabled switch which tries to join an existing operational stack. unitIgnored(2) occurs on an operational stack, when a BU enabled switch tries to join the stack.
OBJECT-TYPE    
  INTEGER cannotJoinStack(1), unitIgnored(2)  

bsnUSBInfo 1.3.6.1.4.1.45.5.2.1.18
The USB module information.
OBJECT-TYPE    
  DisplayString Size(0..255)  

bsnSFPInfo 1.3.6.1.4.1.45.5.2.1.19
The SFP module information.
OBJECT-TYPE    
  DisplayString Size(0..255)  

bsnAaaUserName 1.3.6.1.4.1.45.5.2.1.20
The user name of an AAA user account.
OBJECT-TYPE    
  SnmpAdminString Size(10..16)  

bsnConfigurationSavedToNvram 1.3.6.1.4.1.45.5.2.2.0.1
This notification is generated whenever the device saves its configuration to non-volatile storage. The system should limit the frequency with which this notification is generated, as frequent configuration changes could potentially generate too many of these notifications. How the frequency is limitted is an implementation details, but it is suggested that no more than one notification be generated per minute.
NOTIFICATION-TYPE    

bsnEapAccessViolation 1.3.6.1.4.1.45.5.2.2.0.2
This notification is generated whenever an EAP access violation occurs.
NOTIFICATION-TYPE    

bsnPortSpeedDuplexMismatch 1.3.6.1.4.1.45.5.2.2.0.3
This notification is generated when a speed or duplex mismatch is detected. Once notification has been sent, further notifications may be sent, but it is suggested these be at least 5 minutes apart.
NOTIFICATION-TYPE    

bsnStackManagerReconfiguration 1.3.6.1.4.1.45.5.2.2.0.4
This notification is generated by a stackable system when the stack manager detects a problem with a link between stack members.
NOTIFICATION-TYPE    

bsnLacTrunkUnavailable 1.3.6.1.4.1.45.5.2.2.0.5
This notification is generated when the last trunk is occupied out of a limited number of trunks that can be created. The condition usually occurs because a system has some hardware or software limit on the number of trunks that can be created.
NOTIFICATION-TYPE    

bsnLoginFailure 1.3.6.1.4.1.45.5.2.2.0.6
This notification is generated when an attempt to login to the system fails as a result of an incorrect password.
NOTIFICATION-TYPE    

bsnMLTHealthFailure 1.3.6.1.4.1.45.5.2.2.0.7
This notification is generated when a receiving switch does not receive an expected number of autotopology frames on an MLT in a given time interval from the sending switch(es) on the other end of the MLT. Once notification has been sent, further notifications may be sent, but it is suggested these be at least 5 minutes apart. The ifAdminStatus object reflects the state of the port. The port may be partitioned by the switch or still be active depending on the detection algorithm's control parameters.
NOTIFICATION-TYPE    

bsnTrunkPortDisabledToPreventBroadcastStorm 1.3.6.1.4.1.45.5.2.2.0.8
This notification is generated when an MLT port is disabled as a result of an MLT trunk being disabled.
NOTIFICATION-TYPE    

bsnLacPortDisabledToPreventBroadcastStorm 1.3.6.1.4.1.45.5.2.2.0.9
This notification is generated when a LAG port that was port of a trunk is disabled as a result of the LAC setting on the port being turned off.
NOTIFICATION-TYPE    

bsnTrunkPortEnabledToPreventBroadcastStorm 1.3.6.1.4.1.45.5.2.2.0.10
This notification is generated when an MLT port is enabled as a result of an MLT trunk being disabled.
NOTIFICATION-TYPE    

bsnLacPortDisabledDueToLossOfVLACPDU 1.3.6.1.4.1.45.5.2.2.0.11
Generated when a port is disabled due to the loss of a VLACP PDU.
NOTIFICATION-TYPE    

bsnLacPortEnabledDueToReceiptOfVLACPDU 1.3.6.1.4.1.45.5.2.2.0.12
Generated when a port is enabled due to receipt of a VLACP PDU.
NOTIFICATION-TYPE    

bsnStackConfigurationError 1.3.6.1.4.1.45.5.2.2.0.13
This notification is generated when the expected size of a stack is not equal to the actual size of the stack.
NOTIFICATION-TYPE    

bsnEapUbpFailure 1.3.6.1.4.1.45.5.2.2.0.14
This notification is generated when installation of a UBP policy fails following EAP authentication.
NOTIFICATION-TYPE    

bsnTrialLicenseExpiration 1.3.6.1.4.1.45.5.2.2.0.15
This notification is generated to indicate that a trial license is going to expire soon, or has already expired.
NOTIFICATION-TYPE    

bsnEnteredForcedStackMode 1.3.6.1.4.1.45.5.2.2.0.16
This notification is generated to indicate that a switch has entered forced stack mode.
NOTIFICATION-TYPE    

bsnTemperatureExceeded 1.3.6.1.4.1.45.5.2.2.0.17
This notification is generated when the temperature of a chassis component has exceeded some threshold. The instance of s5ChasComType included in the notification identifies the component.
NOTIFICATION-TYPE    

bsnEapRAVError 1.3.6.1.4.1.45.5.2.2.0.18
This notification indicates that an Eap client MAC address was authorized on a port, but the port could not be moved to the Radius-Assigned VLAN.
NOTIFICATION-TYPE    

bsnEapRateLimitExceeded 1.3.6.1.4.1.45.5.2.2.0.19
This notification indicates that incoming traffic on a port exceeded the rate limit settings on that port.
NOTIFICATION-TYPE    

bsnSystemUp365Days 1.3.6.1.4.1.45.5.2.2.0.20
This notification indicates that the system has been up for 365 days. In stack configuration, bayStackUnitConfigIndex specifies the unit number. For a standalone unit bayStackUnitConfigIndex is always 1.
NOTIFICATION-TYPE    

bsnUSBInsertion 1.3.6.1.4.1.45.5.2.2.0.21
This notification is triggered when an USB device is inserted. In stack configuration, s5AgSysUsbTargetUnit specifies the unit number. For standalone, s5AgSysUsbTargetUnit is always 0.
NOTIFICATION-TYPE    

bsnUSBRemoval 1.3.6.1.4.1.45.5.2.2.0.22
This notification is triggered when an USB device is removed. In stack configuration, s5AgSysUsbTargetUnit specifies the unit number. For standalone, s5AgSysUsbTargetUnit is always 0.
NOTIFICATION-TYPE    

bsnSFPInsertion 1.3.6.1.4.1.45.5.2.2.0.23
This notification is triggered when an SFP module is inserted.
NOTIFICATION-TYPE    

bsnSFPRemoval 1.3.6.1.4.1.45.5.2.2.0.24
This notification is triggered when an SFP module is removed.
NOTIFICATION-TYPE    

bsnROPasswordExpired 1.3.6.1.4.1.45.5.2.2.0.25
This notification is sent when RO password expired.
NOTIFICATION-TYPE    

bsnRWPasswordExpired 1.3.6.1.4.1.45.5.2.2.0.26
This notification is sent when RW password expired.
NOTIFICATION-TYPE    

bsnStackProtection 1.3.6.1.4.1.45.5.2.2.0.27
This notification is sent when a stack protection event occurs. The event type is specified by the bsnStackProtectionEvent object.
NOTIFICATION-TYPE    

bsnRunScripts 1.3.6.1.4.1.45.5.2.2.0.28
This notification is sent when a script has been run. It indicates whether the execution was successful or not.
NOTIFICATION-TYPE    

bsnAaaUserAccountNotUsed 1.3.6.1.4.1.45.5.2.2.0.29
A bsnAaaUserAccountNotUsed trap signifies that a user account has never been used during a time interval.
NOTIFICATION-TYPE    

bsnAaaAlreadyConnected 1.3.6.1.4.1.45.5.2.2.0.30
A bsnAaaAlreadyConnected trap signifies that a user is already connected while he attempts to connect again.
NOTIFICATION-TYPE    

bsnAaaIncorrectLogOnThresholdExceeded 1.3.6.1.4.1.45.5.2.2.0.31
A bsnAaaIncorrectLogOnThresholdExceeded trap signifies that the threshold for incorrect user-entered information is exceeded.
NOTIFICATION-TYPE    

bsnAaaMaxNoOfSessionsExceeded 1.3.6.1.4.1.45.5.2.2.0.32
A bsnAaaMaxNoOfSessionsExceeded trap signifies that the maxim number of current sessions for an AAA user account is exceeded.
NOTIFICATION-TYPE    

bsnAuditUnsentMessages 1.3.6.1.4.1.45.5.2.2.0.33
A bsnAuditUnsentMessages trap signifies that the number of audit unsent messages has reached 50% from the total capacity.
NOTIFICATION-TYPE    

bsnAuditRecordEventsFailure 1.3.6.1.4.1.45.5.2.2.0.34
A bsnAuditRecordEventsFailure trap signifies that security log fails to record the events that are required to be recorded.
NOTIFICATION-TYPE    

bsnAuditStartUpTrap 1.3.6.1.4.1.45.5.2.2.0.35
A bsnAuditStartUpTrap trap signifies that the audit function starts up.
NOTIFICATION-TYPE    

bsnAuditShutDownTrap 1.3.6.1.4.1.45.5.2.2.0.36
A bsnAuditStartUpTrap trap signifies that the audit function shuts down.
NOTIFICATION-TYPE