ATSWTCH2-MIB

File: ATSWTCH2-MIB.mib (100524 bytes)

Imported modules

RFC1155-SMI	RFC1213-MIB	RFC-1215
RFC-1212

Imported symbols

enterprises	Counter	IpAddress
TimeTicks	DisplayString	TRAP-TYPE
OBJECT-TYPE

Defined Types

MacAddress
OCTET STRING	Size(6)

BridgeId
OCTET STRING	Size(8)

Timeout
INTEGER

AtswitchNwMgrEntry
SEQUENCE
	atswitchNwMgrIndex	INTEGER
	atswitchNwMgrIpAddr	IpAddress

AtswitchPortEntry
SEQUENCE
	atswitchPortNumber	INTEGER
	atswitchPortName	DisplayString
	atswitchPortAutosenseOrHalfDuplex	INTEGER
	atswitchPortLinkState	INTEGER
	atswitchPortDuplexStatus	INTEGER
	atswitchPortSpeed	INTEGER
	atswitchPortState	INTEGER
	atswitchPortTransmitPacingConfig	INTEGER
	atswitchPortSTPConfig	INTEGER
	atswitchPortBridgeid	INTEGER
	atswitchPortSTPCost	INTEGER
	atswitchPortSTPPriority	INTEGER
	atswitchPortSwitchingType	INTEGER
	atswitchPortFlowControlEnable	INTEGER
	atswitchPortSecurityNumberOfAddresses	INTEGER

AtswitchBasicVlanEntry
SEQUENCE
	atswitchBeVlanIndex	INTEGER
	atswitchBeVlanName	DisplayString
	atswitchBeVlanTagId	INTEGER
	atswitchBeVlanPortMask	DisplayString
	atswitchBeVlanRowStatus	INTEGER

AtswitchPort2VlanEntry
SEQUENCE
	atswitchPvPortNumber	INTEGER
	atswitchPvVlanName	DisplayString

AtswitchEthPortMonEntry
SEQUENCE
	atswitchEthPortMonId	INTEGER
	atswitchEthPortMonTxTotalBytes	Counter
	atswitchRxGoodFrames	Counter
	atswitchTxGoodFrames	Counter
	atswitchTxBroadcastFrames	Counter
	atswitchTxMulticastFrames	Counter
	atswitchAddrDuplicate	Counter
	atswitchAddrMismatches	Counter
	atswitchRxOverruns	Counter

AtswitchEthPortErrorEntry
SEQUENCE
	atswitchEthPortErrorId	INTEGER
	atswitchEthPortErrorRxBadFrames	Counter
	atswitchEthPortErrorTxTotal	Counter

AtswitchFwdVlanEntry
SEQUENCE
	atswitchFwdVlanMACAddr	MacAddress
	atswitchFwdVlanVlanId	INTEGER
	atswitchFwdVlanAge	INTEGER
	atswitchFwdVlanStatus	INTEGER
	atswitchFwdVlanPort	INTEGER

AtswitchBrBaseEntry
SEQUENCE
	atswitchBrBaseLanId	INTEGER
	atswitchBrBaseBridgeAddress	MacAddress
	atswitchBrBaseNumPorts	INTEGER
	atswitchBrBaseType	INTEGER

AtswitchBrBasePortEntry
SEQUENCE
	atswitchBrBasePortLanId	INTEGER
	atswitchBrBasePort	INTEGER
	atswitchBrBasePortIfIndex	INTEGER
	atswitchBrBasePortCircuit	OBJECT IDENTIFIER
	atswitchBrBasePortDelayExceededDiscards	Counter
	atswitchBrBasePortMtuExceededDiscards	Counter

AtswitchBrStpEntry
SEQUENCE
	atswitchBrStpLanId	INTEGER
	atswitchBrStpProtocolSpecification	INTEGER
	atswitchBrStpPriority	INTEGER
	atswitchBrStpTimeSinceTopologyChange	TimeTicks
	atswitchBrStpTopChanges	Counter
	atswitchBrStpDesignatedRoot	BridgeId
	atswitchBrStpRootCost	INTEGER
	atswitchBrStpRootPort	INTEGER
	atswitchBrStpMaxAge	Timeout
	atswitchBrStpHelloTime	Timeout
	atswitchBrStpHoldTime	INTEGER
	atswitchBrStpForwardDelay	Timeout
	atswitchBrStpBridgeMaxAge	Timeout
	atswitchBrStpBridgeHelloTime	Timeout
	atswitchBrStpBridgeForwardDelay	Timeout

AtswitchBrStpPortEntry
SEQUENCE
	atswitchBrStpPortLanId	INTEGER
	atswitchBrStpPort	INTEGER
	atswitchBrStpPortPriority	INTEGER
	atswitchBrStpPortState	INTEGER
	atswitchBrStpPortEnable	INTEGER
	atswitchBrStpPortPathCost	INTEGER
	atswitchBrStpPortDesignatedRoot	BridgeId
	atswitchBrStpPortDesignatedCost	INTEGER
	atswitchBrStpPortDesignatedBridge	BridgeId
	atswitchBrStpPortDesignatedPort	OCTET STRING
	atswitchBrStpPortForwardTransitions	Counter

AtswitchBrTpEntry
SEQUENCE
	atswitchBrTpLanId	INTEGER
	atswitchBrTpLearnedEntryDiscards	Counter
	atswitchBrTpAgingTime	INTEGER

AtswitchBrTpFdbEntry
SEQUENCE
	atswitchBrTpFdbLanId	INTEGER
	atswitchBrTpFdbAddress	MacAddress
	atswitchBrTpFdbPort	INTEGER
	atswitchBrTpFdbStatus	INTEGER

AtswitchBrTpPortEntry
SEQUENCE
	atswitchBrTpPortLanId	INTEGER
	atswitchBrTpPort	INTEGER
	atswitchBrTpPortMaxInfo	INTEGER
	atswitchBrTpPortInFrames	Counter
	atswitchBrTpPortOutFrames	Counter
	atswitchBrTpPortInDiscards	Counter

AtswitchStaticMACEntry
SEQUENCE
	atswitchStaticMACAddress	MacAddress
	atswitchStaticMACPortNumbers	DisplayString
	atswitchStaticMACVlan	INTEGER

AtswitchPortMACEntry
SEQUENCE
	atswitchPortMACAddress	MacAddress
	atswitchPortMACPort	INTEGER

AtswitchMallocLogEntry
SEQUENCE
	atswitchDebugMallocLogIndex	INTEGER
	atswitchDebugMallocLogCaller	INTEGER
	atswitchDebugMallocLogAddress	INTEGER

Defined Values

alliedTelesyn		1.3.6.1.4.1.207
OBJECT IDENTIFIER

atiProduct		1.3.6.1.4.1.207.1
OBJECT IDENTIFIER

mibObject		1.3.6.1.4.1.207.8
OBJECT IDENTIFIER

atswitchMib		1.3.6.1.4.1.207.8.10
OBJECT IDENTIFIER

atswitchSysGroup		1.3.6.1.4.1.207.8.10.1
OBJECT IDENTIFIER

atswitchConfigGroup		1.3.6.1.4.1.207.8.10.2
OBJECT IDENTIFIER

atswitchPortConfigGroup		1.3.6.1.4.1.207.8.10.3
OBJECT IDENTIFIER

atswitchVlanConfigGroup		1.3.6.1.4.1.207.8.10.4
OBJECT IDENTIFIER

atswitchEthernetStatsGroup		1.3.6.1.4.1.207.8.10.5
OBJECT IDENTIFIER

atswitchEthPortStatsGroup		1.3.6.1.4.1.207.8.10.6
OBJECT IDENTIFIER

atswitchFwdVlanGroup		1.3.6.1.4.1.207.8.10.7
OBJECT IDENTIFIER

atswitchTrapAttrGroup		1.3.6.1.4.1.207.8.10.8
OBJECT IDENTIFIER

atswitchBridgeMib		1.3.6.1.4.1.207.8.10.9
OBJECT IDENTIFIER

atswitchStaticMACGroup		1.3.6.1.4.1.207.8.10.10
OBJECT IDENTIFIER

atswitchPortMacAddrGroup		1.3.6.1.4.1.207.8.10.12
OBJECT IDENTIFIER

atswitchDebugMallocLogGroup		1.3.6.1.4.1.207.8.10.13
OBJECT IDENTIFIER

atswitchBrBase		1.3.6.1.4.1.207.8.10.9.1
OBJECT IDENTIFIER

atswitchBrStp		1.3.6.1.4.1.207.8.10.9.2
OBJECT IDENTIFIER

atswitchBrTp		1.3.6.1.4.1.207.8.10.9.3
OBJECT IDENTIFIER

atswitchProductType		1.3.6.1.4.1.207.8.10.1.1
This object will return Product Type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	at-3726(1), at-3714(2), at-8124XL(3), at-8118(4), at-3726XL(5), at-3714FXL(6), at-3716XL(7), other(10)

atswitchEthernetPortCount		1.3.6.1.4.1.207.8.10.1.2
This object will return the number of 10/100 Mbps Ethernet ports on the switch.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchReset		1.3.6.1.4.1.207.8.10.1.3
Setting this object to 'switch-reset' will cause the switch to perform a hardware reset within approximately 4-6 seconds. Setting this object to 'switch-no-reset will have no effect. The value 'no-reset' will be returned whenever this object is retrieved.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	switch-no-reset(1), switch-reset(2)

atswitchMDA1Type		1.3.6.1.4.1.207.8.10.1.4
This object returns the MDA type of the Uplink port
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	rj45-mii(1), fiber(2), none(3)

atswitchMDA2Type		1.3.6.1.4.1.207.8.10.1.5
This Object is supported in 81XX product line only. This object returns the MDA type of the Uplink Port named 'B'. It returns 'none' if a 'B' MDA slot is not installed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	rj45-mii(1), fiber(2), none(3)

atswitchDeviceFlowControl		1.3.6.1.4.1.207.8.10.1.6
This Object is supported on 81XX products only. This object configures the Flow Control of the Device
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

atswitchSwGroup		1.3.6.1.4.1.207.8.10.1.7
OBJECT IDENTIFIER

atswitchIpGroup		1.3.6.1.4.1.207.8.10.1.8
OBJECT IDENTIFIER

atswitchNMGroup		1.3.6.1.4.1.207.8.10.1.9
OBJECT IDENTIFIER

atswitchSwProduct		1.3.6.1.4.1.207.8.10.1.7.1
Identifies the software product the device is running.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

atswitchSwVersion		1.3.6.1.4.1.207.8.10.1.7.2
Identifies the version number of the present release.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

atswitchCurrentIpAddress		1.3.6.1.4.1.207.8.10.1.8.1
The Current IP address is the one which is currently used and is obtained dynamically through one of the protocols interaction.( DHCP or Bootp.) This address is NULL if the Address is Statically configured.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

atswitchConfiguredIpAddress		1.3.6.1.4.1.207.8.10.1.8.2
The Configured IP address of the device. This is the address configured through Network or Local Omega.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

atswitchConfiguredSubnetMask		1.3.6.1.4.1.207.8.10.1.8.3
The Configured Subnet Mask of the device.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

atswitchConfiguredRouter		1.3.6.1.4.1.207.8.10.1.8.4
The Configured Gateway/Router address of the device
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

atswitchIPAddressStatus		1.3.6.1.4.1.207.8.10.1.8.5
The IP Address can be obtained/configured by any of the above different ways. This object specifies how IP address currently on the switch Box, was configured/obtained.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	from-dhcp(1), from-bootp(2), from-psuedoip(3), from-Omega(4)

atswitchDNServer		1.3.6.1.4.1.207.8.10.1.8.6
The Configured DNS Server address of the device
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

atswitchDefaultDomainName		1.3.6.1.4.1.207.8.10.1.8.7
This Object defines the Default Domain where this switch can be belong to.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

atswitchNwMgrTable		1.3.6.1.4.1.207.8.10.1.9.1
A list of SNMP Trap Manager stations Entries. The number of entries is given by the switchNwMgrTotal mib object.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchNwMgrEntry

atswitchNwMgrEntry		1.3.6.1.4.1.207.8.10.1.9.1.1
Trap receipt Manager Entry containing ipaddress of the configured NMS's to which Traps are sent.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchNwMgrEntry

atswitchNwMgrIndex		1.3.6.1.4.1.207.8.10.1.9.1.1.1
The Index of the Managers Ip address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

atswitchNwMgrIpAddr		1.3.6.1.4.1.207.8.10.1.9.1.1.2
The IP Address of the NMS host configured.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

atswitchPortDisableOnSecurityViolation		1.3.6.1.4.1.207.8.10.2.1
This System wide attribute allows the port to be disabled on Violation of the Security. or suspend the port due to Duplicate Address. Needs More explaination after somebody figures out whether atswitch needs the suspend state.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable-on-security-voilation(1), suspend-on-double-address(2), security-not-yet-initalized(3)

atswitchMirroringSourcePort		1.3.6.1.4.1.207.8.10.2.2
This is the Source port number for which there is another mirror port.If the atswitchEthConfigMirrorState is Enabled then ,the mirror portgets routed with all the packets going in and out of Source port. This arrangement is to put an RMON Probe on mirrored port to Probe the traffic on the Source port. One of the port is dedicated to this so that for any port as source port, this dedicated port can be a mirrored port. This object will return a '0' if the MirrorState is not enabled. For the AT-81XX only the receive activity can be mirrored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

atswitchMirrorState		1.3.6.1.4.1.207.8.10.2.3
if the state of Mirroring is enabled by selecting one of the first three values , then the Mirroring explained above works. If disabled, port operation works normally. No Traffic gets routed from MirroringSourcePort to Destination Mirrored Port. Mirroring of both transmit and receive activity can only be done if the port is half duplex. Choose both only if you know the port will be run in half duplex mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	receive(1), transmit(2), both(3), disabled(4)

atswitchMirroringDestinationPort		1.3.6.1.4.1.207.8.10.2.4
This is the Destination port number for which there is another mirror port.If the atswitchEthConfigMirrorState is Enabled then ,the mirror portgets routed with all the packets going in and out of Destination port. This arrangement is to put an RMON Probe on mirrored port to Probe the traffic on the Destination port. One of the port is dedicated to this so that for any port as destination port, this dedicated port can be a mirrored port. This object will return a '0' if the MirrorState is not enabled. For the AT-81XX only the receive activity can be mirrored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

atswitchSecurityConfig		1.3.6.1.4.1.207.8.10.2.5
This Object is suppported only in 37XX product Line. Security feature configuration Object. The Security disable would let the device carry on the learn-new-address-as-it-comes-in mode as usual. When security is enabled-with-learning-locked, the learning of new address is stopped and the addresses locked in the device is used as the security Database. If an address comes in which is not present in the Device Security Database, then any of the atswitchSecurityAction Configured is triggered. When limited-enabled is selected, a per-port atswitchPortSecurityNumberOfAddresses specify the max number of MACs to be learned .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled-with-learning-locked(2), limited-enabled(3)

atswitchSecurityAction		1.3.6.1.4.1.207.8.10.2.6
Security Action to be carried when the atswitchSecurityConfig is enabled-with-learning-locked or limted-enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	send-trap-only(1), disable-port-only(2), disable-port-and-send-trap(3), do-nothing(4)

atswitchDebugAvailableBytes		1.3.6.1.4.1.207.8.10.2.7
This is strictly for Debug reason and this object should not be beleived as the correct number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchTrunkConfig		1.3.6.1.4.1.207.8.10.2.8
This Object Configures the Trunking for the Uplink Ports only. This feature is currently available only in Fenix 37XX-XL hardware.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

atswitchPortTable		1.3.6.1.4.1.207.8.10.3.1
Table of basic port configuration information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchPortEntry

atswitchPortEntry		1.3.6.1.4.1.207.8.10.3.1.1
An entry in the port config table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchPortEntry

atswitchPortNumber		1.3.6.1.4.1.207.8.10.3.1.1.1
This object identifies the port of the switch.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchPortName		1.3.6.1.4.1.207.8.10.3.1.1.2
This attribute associates a user defined string name with the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

atswitchPortAutosenseOrHalfDuplex		1.3.6.1.4.1.207.8.10.3.1.1.3
This attribute allows an administrative request to configure whether this port can Autosense or Force the Half Duplex
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	portAutoSense(1), forceHalfDuplex(2)

atswitchPortLinkState		1.3.6.1.4.1.207.8.10.3.1.1.4
This attribute allows an administrative request to read the status of link state on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	online(1), offline(2)

atswitchPortDuplexStatus		1.3.6.1.4.1.207.8.10.3.1.1.5
This attribute allows an administrative request to read the status of Duplex on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	fullDuplex(1), halfDuplex(2)

atswitchPortSpeed		1.3.6.1.4.1.207.8.10.3.1.1.6
This attribute allows an administrative request to read/write the speed of this port. This attribure is read-only for all the Ports on AT-37XX product . This Attribute is read-write for ATS21 (AT81XX) product Only. This attribute allows an administrative request to change the speed on ATS21 product.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	tenMBits(1), hundredMBits(2)

atswitchPortState		1.3.6.1.4.1.207.8.10.3.1.1.7
This attribute allows an administrative request to disable or enable communications on this port.It also responds with the status of the port .Except enabled(1) and disabled(2), all values are read-only status.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2), blocking(3), listening(4), learning(5)

atswitchPortTransmitPacingConfig		1.3.6.1.4.1.207.8.10.3.1.1.8
This Object is supported on AT36XX product line Only. This attribute allows the transmit Pacing to be enabled or disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

atswitchPortSTPConfig		1.3.6.1.4.1.207.8.10.3.1.1.9
This attribute allows a bridging Mode to be configured with either Spanning Tree enabled or disabled. When Spanning tree is enabled, make sure that this port is belonging to a valid Bridge_id. Spanning Tree is enabled only when a valid Bridge_id is set.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

atswitchPortBridgeid		1.3.6.1.4.1.207.8.10.3.1.1.10
The Bridge to which this port belongs to .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..64

atswitchPortSTPCost		1.3.6.1.4.1.207.8.10.3.1.1.11
The Cost of the Spanning Tree Protocol.This object is valid only when STP is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atswitchPortSTPPriority		1.3.6.1.4.1.207.8.10.3.1.1.12
The Priority of the spanning Tree Protocol. This object is valid when STP is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atswitchPortSwitchingType		1.3.6.1.4.1.207.8.10.3.1.1.13
This per-port attribute describes whether the port identified by atswitchPortNumber uses store-and-forward bridging for local switched Ethernet packets or cut-through. The Hardware allows cut-through on Transmission and cut-through-on Receive and the same for the store-and-forward. But some of the Config option does not make any sense. So, for now there is no distiction of Rx and Tx. Both Tx/Rx support store-and-forward or cut-through. This Object is not applicable for 37XX with XL hardware as the Hardware does not support both Cut through and Store and Forward. It is default Store and Forward. Even though the Set on either of them is done, Hardware does not do the Cut through Switching.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	fast-cut-through(1), store-and-forward(2)

atswitchPortFlowControlEnable		1.3.6.1.4.1.207.8.10.3.1.1.14
This Per_port attribute is only for ATS21 product.(81XX). This per-port attribute describes whether the port identified has flow Control Enabled or not. Flow Control on Full Duplex and Half Duplex is detected and Automatically, flow control accordingly is taken care of. BY Default, Flow Control is Disabled.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atswitchPortSecurityNumberOfAddresses		1.3.6.1.4.1.207.8.10.3.1.1.15
This object configures the Max number of addresses at an instance to be learnt by the device. If the learnt addresses number is above this number, then the atswitchSecurityAction is triggered . when the number of learnt addresses exceeds this number ,the the atswitchSecurityAction is triggered only if atswitchSecurityConfig is set to limited-enalbled. ELse nothing is triggered.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

atswitchBasicVlanTable		1.3.6.1.4.1.207.8.10.4.1
Table of Virtual LAN configured.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBasicVlanEntry

atswitchBasicVlanEntry		1.3.6.1.4.1.207.8.10.4.1.1
An entry in the table, containing VLAN information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBasicVlanEntry

atswitchBeVlanIndex		1.3.6.1.4.1.207.8.10.4.1.1.1
This object identifies the VLAN.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..64

atswitchBeVlanName		1.3.6.1.4.1.207.8.10.4.1.1.2
This attribute associates a user defined string with the Virtual LAN. To configure a new VLAN, do 'set' operation on this object with the VLAN name. To delete an VLAN, do 'set' operation with string '*'. Before configuring any of the objects in this row , set the atswitchVlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

atswitchBeVlanTagId		1.3.6.1.4.1.207.8.10.4.1.1.3
This object is supported by 37xx series of fenix with the VLAN tagging capability hardware only. Please check whether the SysObjectId is greater than 29. This object configures the VId in the Tag Information header in accordance with 802.1q spec. Before configuring any of the objects in this row , set the atswitchVlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..4095

atswitchBeVlanPortMask		1.3.6.1.4.1.207.8.10.4.1.1.4
This object is supported by 37xx series of fenix with the VLAN tagging capability hardware only. Please check whether the SysObjectId is greater than 29. This Object builds the Output Ports that participate in the Vlan with the atswitchBeVlanName. The Format of the input string would be like '1,2,5,7,12'. Before configuring any of the objects in this row , set the atswitchVlanStatus to 'under-construction' and once configured with all the information, please set the same object to operational
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

atswitchBeVlanRowStatus		1.3.6.1.4.1.207.8.10.4.1.1.5
This object is supported by 37xx series of fenix with the VLAN tagging capability hardware only. Please check whether the SysObjectId is greater than 29. This object identifies the atswitchBeVLANEntry Row Status . The User sets this object to under-construction, to start with to create a row. Once the User Configures the VlanName and TagId and also the Output Ports.This object should be set to operational. If the user does not set this object to operational, the whole row is lost .when a 'get' of this row is done, this uncommited row is not seen. configured in the switch.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	idle(1), operational(2), under-construction(3), not-operational(4)

atswitchPort2VlanTable		1.3.6.1.4.1.207.8.10.4.2
Table of per port Virtual LAN configuration.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchPort2VlanEntry

atswitchPort2VlanEntry		1.3.6.1.4.1.207.8.10.4.2.1
An entry in the table, containing per port VLAN information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchPort2VlanEntry

atswitchPvPortNumber		1.3.6.1.4.1.207.8.10.4.2.1.1
This object identifies the port on the switch.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchPvVlanName		1.3.6.1.4.1.207.8.10.4.2.1.2
This attribute associates a user defined string with the Virtual LAN. This Object is the same as atswitchBeVlanName. Please make sure to give the same string as atswitchBeVlanName.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

atswitchEthMonStats		1.3.6.1.4.1.207.8.10.5.1
OBJECT IDENTIFIER

atswitchEthErrorStats		1.3.6.1.4.1.207.8.10.5.2
OBJECT IDENTIFIER

atswitchEthMonRxGoodFrames		1.3.6.1.4.1.207.8.10.5.1.1
The total number of Good Frames received on this module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthMonTxGoodFrames		1.3.6.1.4.1.207.8.10.5.1.2
The total number of Good Frames Transmitted by this module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthMonTxTotalBytes		1.3.6.1.4.1.207.8.10.5.1.3
The total number of Bytes transmitted from this module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthMonTxDeferred		1.3.6.1.4.1.207.8.10.5.1.4
This is the count of first time Transmission attempt which failed on an interface due to medium being busy.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthMonTxCollisions		1.3.6.1.4.1.207.8.10.5.1.5
The total number of collisions while switching on an interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthErrorCRC		1.3.6.1.4.1.207.8.10.5.2.1
The total number of CRC errors on received packets.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthErrorAlignment		1.3.6.1.4.1.207.8.10.5.2.2
The total number of packets received that has alignment errors
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthErrorRxBadFrames		1.3.6.1.4.1.207.8.10.5.2.3
The counter is incremented when a bad frame was received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthErrorLateCollisions		1.3.6.1.4.1.207.8.10.5.2.4
This object counts the number of times the collison was detected in the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthErrorTxTotal		1.3.6.1.4.1.207.8.10.5.2.6
Total number of error resulted from transfer operations.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthPortMonStats		1.3.6.1.4.1.207.8.10.6.1
OBJECT IDENTIFIER

atswitchEthPortError		1.3.6.1.4.1.207.8.10.6.2
OBJECT IDENTIFIER

atswitchEthPortMonTable		1.3.6.1.4.1.207.8.10.6.1.1
A list of statistics entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchEthPortMonEntry

atswitchEthPortMonEntry		1.3.6.1.4.1.207.8.10.6.1.1.1
A collection of statistics kept for a particular port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchEthPortMonEntry

atswitchEthPortMonId		1.3.6.1.4.1.207.8.10.6.1.1.1.1
The relative position of a port within a switch starting with 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchEthPortMonTxTotalBytes		1.3.6.1.4.1.207.8.10.6.1.1.1.2
The total number of Bytes transmited to this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchRxGoodFrames		1.3.6.1.4.1.207.8.10.6.1.1.1.3
The total number of good packets(including unicast,broadcast packets and multicast packets) received
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchTxGoodFrames		1.3.6.1.4.1.207.8.10.6.1.1.1.4
The total number of good packets(including bad packets, broadcast packets and multicast packets) transmitted successfully
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchTxBroadcastFrames		1.3.6.1.4.1.207.8.10.6.1.1.1.5
The total number of packets transmitted that were directed to the broadcast address. This does not include multicast packets
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchTxMulticastFrames		1.3.6.1.4.1.207.8.10.6.1.1.1.6
The total number of packets transmitted that were directed to a multicast address. This does not include packets addressed to the broadcast address
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchAddrDuplicate		1.3.6.1.4.1.207.8.10.6.1.1.1.7
The number of address duplications seen on this port which is secured on another port. If a source address is locked for a port and if that address is eeen as source address on this port, then such occurances of duplicate Address is noted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchAddrMismatches		1.3.6.1.4.1.207.8.10.6.1.1.1.8
Address mismatches /address changes the sum of : 1. The number of mismatches seen on a port between a securely assigned port address and the source address observed on the port. Occurrence of this causes the TNETX3150 to suspend the port. 2. The number of times the TNETX3150 is required to assign or learn an address for a port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchRxOverruns		1.3.6.1.4.1.207.8.10.6.1.1.1.9
The number of frames lost due to lack of resources during frame reception. The counter is incremented when frame data cannot enter the RX fifo for whatever reason. Frames that overrun after entering the fifo also can be counted as RX discards if they are not cut-through.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthPortErrorTable		1.3.6.1.4.1.207.8.10.6.2.1
A list of statistics entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchEthPortErrorEntry

atswitchEthPortErrorEntry		1.3.6.1.4.1.207.8.10.6.2.1.1
A collection of statistics kept for a particular port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchEthPortErrorEntry

atswitchEthPortErrorId		1.3.6.1.4.1.207.8.10.6.2.1.1.1
The relative position of a port within a switch starting with 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchEthPortErrorRxBadFrames		1.3.6.1.4.1.207.8.10.6.2.1.1.2
The counter is incremented when a bad frame was received on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchEthPortErrorTxTotal		1.3.6.1.4.1.207.8.10.6.2.1.1.3
Total number of error resulted from transmit operations on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchFwdVlanTable		1.3.6.1.4.1.207.8.10.7.1
This tables lists Mac Addresses lexicographically from the forwarding table and also the information about the Vlan/Vlan which this MAC address belongs to.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchFwdVlanEntry

atswitchFwdVlanEntry		1.3.6.1.4.1.207.8.10.7.1.1
Entry in the atswitchFwdVlanTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchFwdVlanEntry

atswitchFwdVlanMACAddr		1.3.6.1.4.1.207.8.10.7.1.1.1
This object identifies the MAC Address associated with this entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

atswitchFwdVlanVlanId		1.3.6.1.4.1.207.8.10.7.1.1.2
This object identifies the Vlan/Vlan which MAC Address defined by the atswitchFwdMACAddr is associated with.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchFwdVlanAge		1.3.6.1.4.1.207.8.10.7.1.1.3
Current Age of the MACAddr in the Forwarding Table.It Starts with 0 and if not heard it increments to some value until it hears from it and if not heard before reaching Max value, it will purge this entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchFwdVlanStatus		1.3.6.1.4.1.207.8.10.7.1.1.4
The status of this entry. The meanings of the values are: inactive(1) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. active(2) : the value of the corresponding instance of atswitchFwdVlanPort was active, and is being used. other(3) : none of the following.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(1), active(2), other(3)

atswitchFwdVlanPort		1.3.6.1.4.1.207.8.10.7.1.1.5
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of atswitchFwdVlanMACAddr has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address. Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of atswitchFwdVlanStatus is not learned(3).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrBaseTable		1.3.6.1.4.1.207.8.10.9.1.1
Table of basic bridge information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrBaseEntry

atswitchBrBaseEntry		1.3.6.1.4.1.207.8.10.9.1.1.1
An entry in the atswitchBrBaseTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrBaseEntry

atswitchBrBaseLanId		1.3.6.1.4.1.207.8.10.9.1.1.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrBaseBridgeAddress		1.3.6.1.4.1.207.8.10.9.1.1.1.2
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with atswitchBrStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

atswitchBrBaseNumPorts		1.3.6.1.4.1.207.8.10.9.1.1.1.3
The number of ports controlled by this bridging entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrBaseType		1.3.6.1.4.1.207.8.10.9.1.1.1.4
Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), transparent-only(2), sourceroute-only(3), srt(4)

atswitchBrBasePortTable		1.3.6.1.4.1.207.8.10.9.1.4
A table that contains generic information about every port that is associated with this bridge. Transparent, source-route, and srt ports are included.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrBasePortEntry

atswitchBrBasePortEntry		1.3.6.1.4.1.207.8.10.9.1.4.1
A list of information for each port of the bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrBasePortEntry

atswitchBrBasePortLanId		1.3.6.1.4.1.207.8.10.9.1.4.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrBasePort		1.3.6.1.4.1.207.8.10.9.1.4.1.2
The port number of the port for which this entry contains bridge management information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atswitchBrBasePortIfIndex		1.3.6.1.4.1.207.8.10.9.1.4.1.3
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrBasePortCircuit		1.3.6.1.4.1.207.8.10.9.1.4.1.4
For a port which (potentially) has the same value of atswitchBrBasePortIfIndex as another port on the same bridge, this object contains the name of an object instance unique to this port. For example, in the case where multiple ports correspond one- to-one with multiple X.25 virtual circuits, this value might identify an (e.g., the first) object instance associated with the X.25 virtual circuit corresponding to this port. For a port which has a unique value of atswitchBrBasePortIfIndex, this object can have the value { 0 0 }.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

atswitchBrBasePortDelayExceededDiscards		1.3.6.1.4.1.207.8.10.9.1.4.1.5
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrBasePortMtuExceededDiscards		1.3.6.1.4.1.207.8.10.9.1.4.1.6
The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrStpTable		1.3.6.1.4.1.207.8.10.9.2.1
Table of bridge spanning tree information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrStpEntry

atswitchBrStpEntry		1.3.6.1.4.1.207.8.10.9.2.1.1
An entry in the atswitchBrStpTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrStpEntry

atswitchBrStpLanId		1.3.6.1.4.1.207.8.10.9.2.1.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrStpProtocolSpecification		1.3.6.1.4.1.207.8.10.9.2.1.1.2
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), decLb100(2), ieee8021d(3)

atswitchBrStpPriority		1.3.6.1.4.1.207.8.10.9.2.1.1.3
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of atswitchBrBaseBridgeAddress.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

atswitchBrStpTimeSinceTopologyChange		1.3.6.1.4.1.207.8.10.9.2.1.1.4
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

atswitchBrStpTopChanges		1.3.6.1.4.1.207.8.10.9.2.1.1.5
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrStpDesignatedRoot		1.3.6.1.4.1.207.8.10.9.2.1.1.6
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeId

atswitchBrStpRootCost		1.3.6.1.4.1.207.8.10.9.2.1.1.7
The cost of the path to the root as seen from this bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrStpRootPort		1.3.6.1.4.1.207.8.10.9.2.1.1.8
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrStpMaxAge		1.3.6.1.4.1.207.8.10.9.2.1.1.9
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Timeout

atswitchBrStpHelloTime		1.3.6.1.4.1.207.8.10.9.2.1.1.10
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Timeout

atswitchBrStpHoldTime		1.3.6.1.4.1.207.8.10.9.2.1.1.11
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrStpForwardDelay		1.3.6.1.4.1.207.8.10.9.2.1.1.12
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to atswitchBrStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
Status: mandatory	Access: read-only
OBJECT-TYPE
	Timeout

atswitchBrStpBridgeMaxAge		1.3.6.1.4.1.207.8.10.9.2.1.1.13
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of atswitchBrStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Timeout	600..4000

atswitchBrStpBridgeHelloTime		1.3.6.1.4.1.207.8.10.9.2.1.1.14
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Timeout	100..1000

atswitchBrStpBridgeForwardDelay		1.3.6.1.4.1.207.8.10.9.2.1.1.15
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of atswitchBrStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Timeout	400..3000

atswitchBrStpPortTable		1.3.6.1.4.1.207.8.10.9.2.15
A table that contains port-specific information for the Spanning Tree Protocol.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrStpPortEntry

atswitchBrStpPortEntry		1.3.6.1.4.1.207.8.10.9.2.15.1
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrStpPortEntry

atswitchBrStpPortLanId		1.3.6.1.4.1.207.8.10.9.2.15.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrStpPort		1.3.6.1.4.1.207.8.10.9.2.15.1.2
The port number of the port for which this entry contains Spanning Tree Protocol management information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atswitchBrStpPortPriority		1.3.6.1.4.1.207.8.10.9.2.15.1.3
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of atswitchBrStpPort.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

atswitchBrStpPortState		1.3.6.1.4.1.207.8.10.9.2.15.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see atswitchBrStpPortEnable), this object will have a value of disabled(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)

atswitchBrStpPortEnable		1.3.6.1.4.1.207.8.10.9.2.15.1.5
The enabled/disabled status of the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

atswitchBrStpPortPathCost		1.3.6.1.4.1.207.8.10.9.2.15.1.6
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

atswitchBrStpPortDesignatedRoot		1.3.6.1.4.1.207.8.10.9.2.15.1.7
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeId

atswitchBrStpPortDesignatedCost		1.3.6.1.4.1.207.8.10.9.2.15.1.8
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrStpPortDesignatedBridge		1.3.6.1.4.1.207.8.10.9.2.15.1.9
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: mandatory	Access: read-only
OBJECT-TYPE
	BridgeId

atswitchBrStpPortDesignatedPort		1.3.6.1.4.1.207.8.10.9.2.15.1.10
The Port Identifier of the port on the Designated Bridge for this port's segment.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

atswitchBrStpPortForwardTransitions		1.3.6.1.4.1.207.8.10.9.2.15.1.11
The number of times this port has transitioned from the Learning state to the Forwarding state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrTpTable		1.3.6.1.4.1.207.8.10.9.3.1
Table of transparent bridging information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrTpEntry

atswitchBrTpEntry		1.3.6.1.4.1.207.8.10.9.3.1.1
An entry in the atswitchBrTpTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrTpEntry

atswitchBrTpLanId		1.3.6.1.4.1.207.8.10.9.3.1.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrTpLearnedEntryDiscards		1.3.6.1.4.1.207.8.10.9.3.1.1.2
The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrTpAgingTime		1.3.6.1.4.1.207.8.10.9.3.1.1.3
The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	10..1000000

atswitchBrTpFdbTable		1.3.6.1.4.1.207.8.10.9.3.3
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrTpFdbEntry

atswitchBrTpFdbEntry		1.3.6.1.4.1.207.8.10.9.3.3.1
Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrTpFdbEntry

atswitchBrTpFdbLanId		1.3.6.1.4.1.207.8.10.9.3.3.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrTpFdbAddress		1.3.6.1.4.1.207.8.10.9.3.3.1.2
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

atswitchBrTpFdbPort		1.3.6.1.4.1.207.8.10.9.3.3.1.3
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of atswitchBrTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address . Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of atswitchBrTpFdbStatus is not learned(3).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrTpFdbStatus		1.3.6.1.4.1.207.8.10.9.3.3.1.4
The status of this entry. The meanings of the values are: inactive(1) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. active(2) : the value of the corresponding instance of atswitchBrTpFdbPort was active, and is being used. other(3) : none of the following. This would include the case where some other MIB object (not the corresponding instance of atswitchBrTpFdbPort ) is being used to determine if and how frames addressed to the value of the corresponding instance of atswitchBrTpFdbAddress are being forwarded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(1), active(2), other(3)

atswitchBrTpPortTable		1.3.6.1.4.1.207.8.10.9.3.4
A table that contains information about every port that is associated with this transparent bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchBrTpPortEntry

atswitchBrTpPortEntry		1.3.6.1.4.1.207.8.10.9.3.4.1
A list of information for each port of a transparent bridge.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchBrTpPortEntry

atswitchBrTpPortLanId		1.3.6.1.4.1.207.8.10.9.3.4.1.1
This object uniquely identifies the lan or Virtual lan.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrTpPort		1.3.6.1.4.1.207.8.10.9.3.4.1.2
The port number of the port for which this entry contains Transparent bridging management information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atswitchBrTpPortMaxInfo		1.3.6.1.4.1.207.8.10.9.3.4.1.3
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchBrTpPortInFrames		1.3.6.1.4.1.207.8.10.9.3.4.1.4
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrTpPortOutFrames		1.3.6.1.4.1.207.8.10.9.3.4.1.5
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchBrTpPortInDiscards		1.3.6.1.4.1.207.8.10.9.3.4.1.6
Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

atswitchStaticMACTable		1.3.6.1.4.1.207.8.10.10.1
This tables lists Mac Addresses lexicographically from the Static table which binds MAC addresses to ports on the switch.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchStaticMACEntry

atswitchStaticMACEntry		1.3.6.1.4.1.207.8.10.10.1.1
Entry in the atswitchStaticMACTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchStaticMACEntry

atswitchStaticMACAddress		1.3.6.1.4.1.207.8.10.10.1.1.1
This object identifies the MAC Address associated with Static MAC Table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

atswitchStaticMACPortNumbers		1.3.6.1.4.1.207.8.10.10.1.1.2
This object identifies the Ports for which the above MAC address is associated Statically in Static MAC Table. This Object could take the port numbers as the Static Address added can be Multicast addresses. This Object is a DisplayString So, the input for example would be 1,5,6,8,9
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

atswitchStaticMACVlan		1.3.6.1.4.1.207.8.10.10.1.1.3
The Static MAC Address to be added can also be confined to a Vlan also. If the Port does not belong to that Vlan. the Port is forced to be moved to that Vlan.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

atswitchPortMACTable		1.3.6.1.4.1.207.8.10.12.1
A table that contains information about unicast entries seen on ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchPortMACEntry

atswitchPortMACEntry		1.3.6.1.4.1.207.8.10.12.1.1
Information about a specific unicast MAC address seen on ports.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AtswitchPortMACEntry

atswitchPortMACAddress		1.3.6.1.4.1.207.8.10.12.1.1.1
A unicast MAC address seen on this port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	MacAddress

atswitchPortMACPort		1.3.6.1.4.1.207.8.10.12.1.1.2
This object identifies the port on which the atswitchPortMACAddress was seen.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchDebugMallocLogTable		1.3.6.1.4.1.207.8.10.13.1
Dont care.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtswitchMallocLogEntry

atswitchMallocLogEntry		1.3.6.1.4.1.207.8.10.13.1.1
Entry in the atswitchDebugMallocLogEntry.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	AtswitchMallocLogEntry

atswitchDebugMallocLogIndex		1.3.6.1.4.1.207.8.10.13.1.1.1
This is strictly for Debug reason and this object should not be beleived as the correct number. This log is useful for finding the memory leak which is stored in Leak_Table. The Entry of this table is the address where malloc is done and no free is done. The size of this 6000.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchDebugMallocLogCaller		1.3.6.1.4.1.207.8.10.13.1.1.2
This is strictly for Debug reason and this object should not be beleived as the correct number. This log is useful for finding the memory leak which is stored in Leak_Table. The Entry of this table is the caller address who malloc'd . The size of this 6000.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchDebugMallocLogAddress		1.3.6.1.4.1.207.8.10.13.1.1.3
This is strictly for Debug reason and this object should not be beleived as the correct number. This log is useful for finding the memory leak which is stored in Leak_Table. The Entry of this table is the address where malloc is done and no free is done. The size of this 6000.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER

atswitchDuplicateMacAddress		1.3.6.1.4.1.207.8.10.8.1
The Duplicate Mac address which is secured on atswitchSecurePortNumber.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

atswitchIntruderMacAddress		1.3.6.1.4.1.207.8.10.8.2
The Mac address of the Intruder as seen on port which is the the next object
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

atswitchSecuredPortNumber		1.3.6.1.4.1.207.8.10.8.3
This is the Port number which has the duplicate Address as the secured address .
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	INTEGER

newRoot		101
The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election. Implementation of this trap is optional.
TRAP-TYPE

topologyChange		102
A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition. Implementation of this trap is optional.
TRAP-TYPE

intruderTrap		105
The intruderTrap trap indicates that there was a Intruder was detected on the port shown as ifIndex.
TRAP-TYPE

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor