ATEN-PE-CFG

File: ATEN-PE-CFG.mib (156246 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215 SNMPv2-SMI SNMP-USER-BASED-SM-MIB
SNMPv2-TC

Imported symbols

enterprises IpAddress Gauge
TimeTicks DisplayString OBJECT-TYPE
TRAP-TYPE MODULE-IDENTITY NOTIFICATION-TYPE
KeyChange TEXTUAL-CONVENTION

Defined Types

DeviceValueEntry  
SEQUENCE    
  deviceValueIndex INTEGER
  deviceCurrent DisplayString
  deviceVoltage DisplayString
  devicePower DisplayString
  devicePowerDissipation DisplayString
  inputMaxVoltage INTEGER
  inputMaxCurrent INTEGER
  powerCapacity INTEGER
  devicePowerFactor DisplayString

SensorValueEntry  
SEQUENCE    
  sensorValueIndex INTEGER
  sensorTemperature DisplayString
  sensorHumidity DisplayString
  sensorPressure DisplayString
  sensorProperty INTEGER

DeviceOutletStatusEntry  
SEQUENCE    
  deviceOutletStatusIndex INTEGER
  displayOutletStatus INTEGER

DeviceConfigEntry  
SEQUENCE    
  deviceConfigIndex INTEGER
  deviceMinCurMT INTEGER
  deviceMaxCurMT INTEGER
  deviceMinVolMT INTEGER
  deviceMaxVolMT INTEGER
  deviceMinPMT INTEGER
  deviceMaxPMT INTEGER
  deviceMaxPDMT INTEGER

DeviceSensorTresholdEntry  
SEQUENCE    
  deviceSensorTresholdIndex INTEGER
  sensorMinTempMT INTEGER
  sensorMaxTempMT INTEGER
  sensorMinHumMT INTEGER
  sensorMaxHumMT INTEGER
  sensorMinPressMT INTEGER
  sensorMaxPressMT INTEGER

OutletCAPEntry  
SEQUENCE    
  outletCAPIndex INTEGER
  outletCAPPriority INTEGER

DeviceIntegerValueEntry  
SEQUENCE    
  deviceIntegerValueIndex INTEGER
  deviceIntegerCurrent INTEGER
  deviceIntegerVoltage INTEGER
  deviceIntegerPower INTEGER
  deviceIntegerPowerDissipation INTEGER

SensorIntegerValueEntry  
SEQUENCE    
  sensorIntegerValueIndex INTEGER
  sensorIntegerTemperature INTEGER
  sensorIntegerHumidity INTEGER
  sensorIntegerPressure INTEGER

OutletValueEntry  
SEQUENCE    
  outletValueIndex INTEGER
  outletCurrent DisplayString
  outletVoltage DisplayString
  outletPower DisplayString
  outletPowerDissipation DisplayString
  outletMaxCurrent INTEGER
  outletPowerFactor DisplayString

OutletSwitchableEntry  
SEQUENCE    
  outletSwitchableIndex INTEGER
  outletSwitchable INTEGER

OutletIntegerValueEntry  
SEQUENCE    
  outletIntegerValueIndex INTEGER
  outletIntegerCurrent INTEGER
  outletIntegerVoltage INTEGER
  outletIntegerPower INTEGER
  outletIntegerPowerDissipation INTEGER

OutletConfigEntry  
SEQUENCE    
  outletConfigIndex INTEGER
  outletName DisplayString
  outletConfirmation INTEGER
  outletOnDelayTime INTEGER
  outletOffDelayTime INTEGER
  outletShutdownMethod INTEGER
  outletMAC DisplayString
  outletMinCurMT INTEGER
  outletMaxCurMT INTEGER
  outletMinVolMT INTEGER
  outletMaxVolMT INTEGER
  outletMinPMT INTEGER
  outletMaxPMT INTEGER
  outletMaxPDMT INTEGER

BreakerStatusEntry  
SEQUENCE    
  breakerStatusIndex INTEGER
  breakerStatus INTEGER

BankValueEntry  
SEQUENCE    
  bankValueIndex INTEGER
  bankCurrent DisplayString
  bankVoltage DisplayString
  bankPower DisplayString
  bankPowerDissipation DisplayString
  bankMaxCurrent INTEGER
  bankAttachStatus INTEGER
  bankPowerFactor DisplayString

BankConfigEntry  
SEQUENCE    
  bankConfigIndex INTEGER
  bankName DisplayString
  bankMinCurMT INTEGER
  bankMaxCurMT INTEGER
  bankMinVolMT INTEGER
  bankMaxVolMT INTEGER
  bankMinPMT INTEGER
  bankMaxPMT INTEGER
  bankMaxPDMT INTEGER

BankControlEntry  
SEQUENCE    
  bankControlIndex INTEGER
  bankControlStatus INTEGER

BankIntegerValueEntry  
SEQUENCE    
  bankIntegerValueIndex INTEGER
  bankIntegerCurrent INTEGER
  bankIntegerVoltage INTEGER
  bankIntegerPower INTEGER
  bankIntegerPowerDissipation INTEGER

SnmpTrapEntry  
SEQUENCE    
  trapReceiverNumber INTEGER
  trapReceiverIPAddress IpAddress
  trapPort INTEGER
  trapCommunity DisplayString
  trapUsername DisplayString
  trapAuthpassword DisplayString
  trapPrivpassword DisplayString

IpFilterEntry  
SEQUENCE    
  ipFilterIndex INTEGER
  ipFilterFrom IpAddress
  ipFilterTo IpAddress

MacFilterEntry  
SEQUENCE    
  macFilterIndex INTEGER
  macFilterSet DisplayString

UsrListEntry  
SEQUENCE    
  usrIndex INTEGER
  usrType INTEGER
  usrName DisplayString
  usrPassword DisplayString
  usrPort1Auth INTEGER
  usrPort2Auth INTEGER
  usrPort3Auth INTEGER
  usrPort4Auth INTEGER
  usrPort5Auth INTEGER
  usrPort6Auth INTEGER
  usrPort7Auth INTEGER
  usrPort8Auth INTEGER
  usrPort9Auth INTEGER
  usrPort10Auth INTEGER
  usrPort11Auth INTEGER
  usrPort12Auth INTEGER
  usrPort13Auth INTEGER
  usrPort14Auth INTEGER
  usrPort15Auth INTEGER
  usrPort16Auth INTEGER
  usrPort17Auth INTEGER
  usrPort18Auth INTEGER
  usrPort19Auth INTEGER
  usrPort20Auth INTEGER
  usrPort21Auth INTEGER
  usrPort22Auth INTEGER
  usrPort23Auth INTEGER
  usrPort24Auth INTEGER
  usrPort25Auth INTEGER
  usrPort26Auth INTEGER
  usrPort27Auth INTEGER
  usrPort28Auth INTEGER
  usrPort29Auth INTEGER
  usrPort30Auth INTEGER
  usrPort31Auth INTEGER
  usrPort32Auth INTEGER
  usrPort33Auth INTEGER
  usrPort34Auth INTEGER
  usrPort35Auth INTEGER
  usrPort36Auth INTEGER
  usrPort37Auth INTEGER
  usrPort38Auth INTEGER
  usrPort39Auth INTEGER
  usrPort40Auth INTEGER
  usrPort41Auth INTEGER
  usrPort42Auth INTEGER
  usrEnable INTEGER

Defined Values

aten 1.3.6.1.4.1.21317
ATEN PE MIB
MODULE-IDENTITY    

atenProducts 1.3.6.1.4.1.21317.1
OBJECT IDENTIFIER    

overip 1.3.6.1.4.1.21317.1.3
OBJECT IDENTIFIER    

poweroverip 1.3.6.1.4.1.21317.1.3.2
OBJECT IDENTIFIER    

pe 1.3.6.1.4.1.21317.1.3.2.2
OBJECT IDENTIFIER    

userManagement 1.3.6.1.4.1.21317.1.3.2.2.1
OBJECT IDENTIFIER    

control 1.3.6.1.4.1.21317.1.3.2.2.2
OBJECT IDENTIFIER    

device 1.3.6.1.4.1.21317.1.3.2.2.2.1
OBJECT IDENTIFIER    

doorSensor 1.3.6.1.4.1.21317.1.3.2.2.2.1.16
OBJECT IDENTIFIER    

pop 1.3.6.1.4.1.21317.1.3.2.2.2.1.17
OBJECT IDENTIFIER    

cap 1.3.6.1.4.1.21317.1.3.2.2.2.1.18
OBJECT IDENTIFIER    

outlet 1.3.6.1.4.1.21317.1.3.2.2.2.2
OBJECT IDENTIFIER    

bank 1.3.6.1.4.1.21317.1.3.2.2.2.3
OBJECT IDENTIFIER    

deviceManagement 1.3.6.1.4.1.21317.1.3.2.2.3
OBJECT IDENTIFIER    

config 1.3.6.1.4.1.21317.1.3.2.2.3.4
OBJECT IDENTIFIER    

dashBoard 1.3.6.1.4.1.21317.1.3.2.2.3.4.4
OBJECT IDENTIFIER    

servicePorts 1.3.6.1.4.1.21317.1.3.2.2.3.4.5
OBJECT IDENTIFIER    

ipv4config 1.3.6.1.4.1.21317.1.3.2.2.3.4.6
OBJECT IDENTIFIER    

eventNotification 1.3.6.1.4.1.21317.1.3.2.2.3.4.7
OBJECT IDENTIFIER    

devicesnmp 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1
OBJECT IDENTIFIER    

syslog 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2
OBJECT IDENTIFIER    

smtp 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3
OBJECT IDENTIFIER    

configurationNotification 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.9
OBJECT IDENTIFIER    

dateTime 1.3.6.1.4.1.21317.1.3.2.2.3.4.8
OBJECT IDENTIFIER    

timeZone 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.1
OBJECT IDENTIFIER    

manualInput 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.2
OBJECT IDENTIFIER    

networkTime 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3
OBJECT IDENTIFIER    

devicesecurity 1.3.6.1.4.1.21317.1.3.2.2.3.5
OBJECT IDENTIFIER    

loginFailures 1.3.6.1.4.1.21317.1.3.2.2.3.5.1
OBJECT IDENTIFIER    

workingMode 1.3.6.1.4.1.21317.1.3.2.2.3.5.2
OBJECT IDENTIFIER    

accountPolicy 1.3.6.1.4.1.21317.1.3.2.2.3.5.3
OBJECT IDENTIFIER    

loginRestriction 1.3.6.1.4.1.21317.1.3.2.2.3.5.4
OBJECT IDENTIFIER    

ipFilter 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2
OBJECT IDENTIFIER    

macFilter 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3
OBJECT IDENTIFIER    

authentication 1.3.6.1.4.1.21317.1.3.2.2.3.5.5
OBJECT IDENTIFIER    

radius 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1
OBJECT IDENTIFIER    

modelName 1.3.6.1.4.1.21317.1.3.2.2.2.1.1
Indicate PE device model name.
OBJECT-TYPE    
  DisplayString  

deviceName 1.3.6.1.4.1.21317.1.3.2.2.2.1.2
The name of PE device. string length: 1~39 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

deviceValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.3
Device value table. This table displays device's current, voltage, power and power dissipation.
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceValueEntry

deviceValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1
Single deviceValue entry containing device info.
OBJECT-TYPE    
  DeviceValueEntry  

deviceValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.1
Index of deviceValue.
OBJECT-TYPE    
  INTEGER 1  

deviceCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.2
Device electric current value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

deviceVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.3
Device voltage value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

devicePower 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.4
Device power value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

devicePowerDissipation 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.5
Device power dissipation value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

inputMaxVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.6
Device input Voltage value. unit:(V) If the device does not support this OID, we show value 0.
OBJECT-TYPE    
  INTEGER  

inputMaxCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.7
Device input Current value. unit:(A) If the device does not support this OID, we show value 0.
OBJECT-TYPE    
  INTEGER  

powerCapacity 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.8
Device power Capacity value.unit:(VA) If the device does not support this OID, we show value 0.
OBJECT-TYPE    
  INTEGER  

devicePowerFactor 1.3.6.1.4.1.21317.1.3.2.2.2.1.3.1.9
Device power Factor value. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

sensorValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.4
Device's sensor value table. This table displays sensor's temperature, humidity and pressure.
OBJECT-TYPE    
  SEQUENCE OF  
    SensorValueEntry

sensorValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1
Single device's sensor value entry containing device info.
OBJECT-TYPE    
  SensorValueEntry  

sensorValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.1
Index of sensor number.
OBJECT-TYPE    
  INTEGER 1..6  

sensorTemperature 1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.2
Sensor's Temperature value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

sensorHumidity 1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.3
Sensor's Humidity value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

sensorPressure 1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.4
Sensor's Pressure value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

sensorProperty 1.3.6.1.4.1.21317.1.3.2.2.2.1.4.1.5
Sensor's Property.
OBJECT-TYPE    
  INTEGER intake(1), exhaust(2), floor(3)  

deviceOutletStatusTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.5
Device outlet status value table.
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceOutletStatusEntry

deviceOutletStatusEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.5.1
Single deviceOutletStatus entry containing device info.
OBJECT-TYPE    
  DeviceOutletStatusEntry  

deviceOutletStatusIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.5.1.1
Index of deviceOutletStatus
OBJECT-TYPE    
  INTEGER 1..30  

displayOutletStatus 1.3.6.1.4.1.21317.1.3.2.2.2.1.5.1.2
Display outlet status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), fault(4), noauth(5), not-support(6), pop(7)  

deviceConfigTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.6
Device configuration table
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceConfigEntry

deviceConfigEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1
Single deviceConfig entry containing device info.
OBJECT-TYPE    
  DeviceConfigEntry  

deviceConfigIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.1
Index of deviceConfig
OBJECT-TYPE    
  INTEGER 1  

deviceMinCurMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.2
Display or set device minimum electric current measurement threshold. Example: range 0.0~32.0 represents 0~320. NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

deviceMaxCurMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.3
Display or set device maximum electric current measurement threshold. Example: range 0.0~32.0 represents 0~320 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

deviceMinVolMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.4
Display or set device minimum voltage measurement threshold. Exapmple: range 90.0~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 900..2600 | -3000  

deviceMaxVolMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.5
Display or set device maximum voltage measurement threshold. Example: range 90.0~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 900..2600 | -3000  

deviceMinPMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.6
Display or set device minimum power measurement threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..99999 | -3000  

deviceMaxPMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.7
Display or set device maximum power measurement threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..99999 | -3000  

deviceMaxPDMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.6.1.8
Display or set device maximum power dissipation measurement threshold. Example: range 0.0 ~ 99999.0 represents 0~999990 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..999990 | -3000  

deviceSensorTresholdTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.7
Device environment value table
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceSensorTresholdEntry

deviceSensorTresholdEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1
Device's sensor Environment entry containing sensor info.
OBJECT-TYPE    
  DeviceSensorTresholdEntry  

deviceSensorTresholdIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.1
Index of sensor number
OBJECT-TYPE    
  INTEGER 1..6  

sensorMinTempMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.2
Display or set sensor minimum temperature measurement threshold. Example: range -20.0 ~ 60.0 represents -200~600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER -200..600 | -3000  

sensorMaxTempMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.3
Display or set sensor maximum temperature measurement threshold. Example: range -20.0 ~ 60.0 represents -200~600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER -200..600 | -3000  

sensorMinHumMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.4
Display or set sensor minimum humidity measurement threshold. Example: range 15.0 ~ 95.0 represents 150~950 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 150..950 | -3000  

sensorMaxHumMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.5
Display or set sensor maximum humidity measurement threshold. Example: range 15.0 ~ 95.0 represents 150~950 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 150..950 | -3000  

sensorMinPressMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.6
Display or set sensor minimum pressure measurement threshold. Example: range -250.0 ~ 250.0 represents -2500 ~ 2500 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER -2500..2500 | -3000  

sensorMaxPressMT 1.3.6.1.4.1.21317.1.3.2.2.2.1.7.1.7
Display or set sensor maximum pressure measurement threshold. Example: range -250.0 ~ 250.0 represents -2500 ~ 2500 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER -2500..2500 | -3000  

deviceOutletControl 1.3.6.1.4.1.21317.1.3.2.2.2.1.8
This function is used for all outlet ports control. Set off(1) to turn off for all outlet ports. Set on(2) to turn on for all outlet ports. Get this object always return nostatus(3), because there is no device status.
OBJECT-TYPE    
  INTEGER off(1), on(2), nostatus(3), not-support(4)  

deviceOutletReboot 1.3.6.1.4.1.21317.1.3.2.2.2.1.9
This function is used for all outlet ports to reboot. Only when outlet status is ON can do outlet reboot action to all ports. Set yes(2) to reboot all outlet ports. Get this object always return no(1).
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-support(4)  

switchable 1.3.6.1.4.1.21317.1.3.2.2.2.1.10
Outlet is switchable or not.
OBJECT-TYPE    
  INTEGER no(1), yes(2), mix(3)  

perportreading 1.3.6.1.4.1.21317.1.3.2.2.2.1.11
Outlet is per-port reading or not.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

sensornumber 1.3.6.1.4.1.21317.1.3.2.2.2.1.12
Sensor number.
OBJECT-TYPE    
  INTEGER  

outletnumber 1.3.6.1.4.1.21317.1.3.2.2.2.1.13
Outlet number.
OBJECT-TYPE    
  INTEGER  

banknumber 1.3.6.1.4.1.21317.1.3.2.2.2.1.14
Bank number.
OBJECT-TYPE    
  INTEGER  

doorSensorStatus 1.3.6.1.4.1.21317.1.3.2.2.2.1.16.1
Display door sensor status. close(0) represents door close. open(1) represents door open. not-attached(2) represents door sensor don't attach to device.
OBJECT-TYPE    
  INTEGER close(0), open(1), not-attached(2), not-support(4)  

doorSensorType 1.3.6.1.4.1.21317.1.3.2.2.2.1.16.2
Door Sensor Type Selection
OBJECT-TYPE    
  INTEGER notinstalled(0), photo(1), inductiveproximity(2), reed(3)  

enablePOPmode 1.3.6.1.4.1.21317.1.3.2.2.2.1.17.1
Enable/Disable POP mode.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

popThreshold 1.3.6.1.4.1.21317.1.3.2.2.2.1.17.2
(-1)means default value same as Bank Max Current 16 A. Example: range 0.0~32.0 represents 0~320 You can define the POP threshold or set as default(-1) value.
OBJECT-TYPE    
  INTEGER  

enableOutletPOPmode 1.3.6.1.4.1.21317.1.3.2.2.2.1.17.3
Enable/Disable Outlet POP mode.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-support(3)  

enableLIFOPOPmode 1.3.6.1.4.1.21317.1.3.2.2.2.1.17.4
Enable/Disable LIFO POP mode.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-support(3)  

enablePriorityPOPmode 1.3.6.1.4.1.21317.1.3.2.2.2.1.17.5
Enable/Disable Priority POP mode.
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-support(3)  

enableCAPmode 1.3.6.1.4.1.21317.1.3.2.2.2.1.18.1
Enable/Disable CAP mode.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

outletCAPTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2
Outlet CAP table
OBJECT-TYPE    
  SEQUENCE OF  
    OutletCAPEntry

outletCAPEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2.1
Outlet CAP entry containing CAP info.
OBJECT-TYPE    
  OutletCAPEntry  

outletCAPIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2.1.1
Index of outlet's CAP configuration
OBJECT-TYPE    
  INTEGER 1..40  

outletCAPPriority 1.3.6.1.4.1.21317.1.3.2.2.2.1.18.2.1.2
Display or set the CAP Priority of outlet. Priority 0 means this outlet does not support this OID.
OBJECT-TYPE    
  INTEGER 0..99  

outletInitMode 1.3.6.1.4.1.21317.1.3.2.2.2.1.19
choose outlet init mode you want.
OBJECT-TYPE    
  INTEGER no-delaytime(1), delaytime(2), not-support(3)  

deviceIntegerValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.99
Device value table. This table displays device's current, voltage, power and power dissipation.
OBJECT-TYPE    
  SEQUENCE OF  
    DeviceIntegerValueEntry

deviceIntegerValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.99.1
Single deviceValue entry containing device info.
OBJECT-TYPE    
  DeviceIntegerValueEntry  

deviceIntegerValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.99.1.1
Index of deviceValue.
OBJECT-TYPE    
  INTEGER 1  

deviceIntegerCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.1.99.1.2
Device electric current value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

deviceIntegerVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.1.99.1.3
Device voltage value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

deviceIntegerPower 1.3.6.1.4.1.21317.1.3.2.2.2.1.99.1.4
Device power value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

deviceIntegerPowerDissipation 1.3.6.1.4.1.21317.1.3.2.2.2.1.99.1.5
Device power dissipation value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

sensorIntegerValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.1.100
Device's sensor value table. This table displays sensor's temperature, humidity and pressure.
OBJECT-TYPE    
  SEQUENCE OF  
    SensorIntegerValueEntry

sensorIntegerValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.1.100.1
Single device's sensor value entry containing device info.
OBJECT-TYPE    
  SensorIntegerValueEntry  

sensorIntegerValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.1.100.1.1
Index of sensor number.
OBJECT-TYPE    
  INTEGER 1..6  

sensorIntegerTemperature 1.3.6.1.4.1.21317.1.3.2.2.2.1.100.1.2
Sensor's Temperature value. This value indicates that 1,000 times. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

sensorIntegerHumidity 1.3.6.1.4.1.21317.1.3.2.2.2.1.100.1.3
Sensor's Humidity value. This value indicates that 1,000 times. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

sensorIntegerPressure 1.3.6.1.4.1.21317.1.3.2.2.2.1.100.1.4
Sensor's Pressure value. This value indicates that 1,000 times. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.2.1
Display total outlet value table
OBJECT-TYPE    
  SEQUENCE OF  
    OutletValueEntry

outletValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1
Single outletValue entry containing outlet info.
OBJECT-TYPE    
  OutletValueEntry  

outletValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.1
Index of outlet number
OBJECT-TYPE    
  INTEGER 1..30  

outletCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.2
Outlet electric current value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

outletVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.3
Outlet voltage value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

outletPower 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.4
Outlet power value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

outletPowerDissipation 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.5
Outlet power dissipation value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

outletMaxCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.6
Outlet Max Current value. unit: (A). If the device does not support this OID, we show value 0.
OBJECT-TYPE    
  INTEGER  

outletPowerFactor 1.3.6.1.4.1.21317.1.3.2.2.2.2.1.1.7
Outlet Power Factor value. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

outlet1Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.2
Display and control outlet 1 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet2Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.3
Display and control outlet 2 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet3Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.4
Display and control outlet 3 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet4Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.5
Display and control outlet 4 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet5Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.6
Display and control outlet 5 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet6Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.7
Display and control outlet 6 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet7Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.8
Display and control outlet 7 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet8Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.9
Display and control outlet 8 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet9Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.11
Display and control outlet 9 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet10Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.12
Display and control outlet 10 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet11Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.13
Display and control outlet 11 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet12Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.14
Display and control outlet 12 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet13Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.15
Display and control outlet 13 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet14Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.16
Display and control outlet 14 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet15Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.17
Display and control outlet 15 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet16Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.18
Display and control outlet 16 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet17Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.19
Display and control outlet 17 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet18Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.20
Display and control outlet 18 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet19Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.21
Display and control outlet 19 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet20Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.22
Display and control outlet 20 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet21Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.23
Display and control outlet 21 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet22Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.24
Display and control outlet 22 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet23Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.25
Display and control outlet 23 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet24Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.26
Display and control outlet 24 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet25Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.27
Display and control outlet 25 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet26Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.28
Display and control outlet 26 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet27Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.29
Display and control outlet 27 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet28Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.30
Display and control outlet 28 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet29Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.31
Display and control outlet 29 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet30Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.32
Display and control outlet 30 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet31Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.33
Display and control outlet 31 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet32Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.34
Display and control outlet 32 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet33Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.35
Display and control outlet 33 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet34Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.36
Display and control outlet 34 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet35Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.37
Display and control outlet 35 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet36Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.38
Display and control outlet 36 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet37Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.39
Display and control outlet 37 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet38Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.40
Display and control outlet 38 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet39Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.41
Display and control outlet 39 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet40Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.42
Display and control outlet 40 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet41Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.43
Display and control outlet 41 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outlet42Status 1.3.6.1.4.1.21317.1.3.2.2.2.2.44
Display and control outlet 42 status. Can't set pending status.
OBJECT-TYPE    
  INTEGER off(1), on(2), pending(3), reboot(4), fault(5), noauth(6), not-support(7), pop(8)  

outletSwitchableTable 1.3.6.1.4.1.21317.1.3.2.2.2.2.70
OBJECT-TYPE    
  SEQUENCE OF  
    OutletSwitchableEntry

outletSwitchableEntry 1.3.6.1.4.1.21317.1.3.2.2.2.2.70.1
Tok_String
OBJECT-TYPE    
  OutletSwitchableEntry  

outletSwitchableIndex 1.3.6.1.4.1.21317.1.3.2.2.2.2.70.1.1
Index of outlet number.
OBJECT-TYPE    
  INTEGER 1..30  

outletSwitchable 1.3.6.1.4.1.21317.1.3.2.2.2.2.70.1.2
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

outletIntegerValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.2.99
Display total outlet value table
OBJECT-TYPE    
  SEQUENCE OF  
    OutletIntegerValueEntry

outletIntegerValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.2.99.1
Single outletValue entry containing outlet info.
OBJECT-TYPE    
  OutletIntegerValueEntry  

outletIntegerValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.2.99.1.1
Index of outlet number.
OBJECT-TYPE    
  INTEGER 1..42  

outletIntegerCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.2.99.1.2
Outlet electric current value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletIntegerVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.2.99.1.3
Outlet voltage value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletIntegerPower 1.3.6.1.4.1.21317.1.3.2.2.2.2.99.1.4
Outlet power value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletIntegerPowerDissipation 1.3.6.1.4.1.21317.1.3.2.2.2.2.99.1.5
Outlet power dissipation value. This value indicates that 1,000 times. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletConfigTable 1.3.6.1.4.1.21317.1.3.2.2.2.2.10
Outlet configuration table
OBJECT-TYPE    
  SEQUENCE OF  
    OutletConfigEntry

outletConfigEntry 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1
Outlet Config entry containing outlet info.
OBJECT-TYPE    
  OutletConfigEntry  

outletConfigIndex 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.1
Index of outlet number
OBJECT-TYPE    
  INTEGER 1..30  

outletName 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.2
Display or set the name of outlet. If the device does not support this OID, we show n/a. string length: 0~15 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

outletConfirmation 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.3
Display or set the confirmation of outlet.
OBJECT-TYPE    
  INTEGER no(1), yes(2), noauth(3), not-support(4)  

outletOnDelayTime 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.4
Display or set the ON delay time of outlet. When this model does not support the OID, we show value -1.
OBJECT-TYPE    
  INTEGER 0..999 | -1  

outletOffDelayTime 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.5
Display or set the OFF delay time of outlet. When this model does not support the OID, we show value -1.
OBJECT-TYPE    
  INTEGER 0..999 | -1  

outletShutdownMethod 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.6
Display or set the shutdown mehtod of outlet.
OBJECT-TYPE    
  INTEGER kill-the-power(1), wake-on-lan(2), after-ac-back(3), not-support(4)  

outletMAC 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.7
Display or set the MAC address of ShutdownMethod. If the device does not support this OID, we show n/a. string length: 12
OBJECT-TYPE    
  DisplayString  

outletMinCurMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.8
Display or set the outlet minimum electric current measurment threshold. Example: range 0.0 ~16.0 rerpresnts 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletMaxCurMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.9
Display or set the outlet maximum electric current measurment threshold. Example: range 0.0 ~16.0 represents 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

outletMinVolMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.10
Display or set the outlet minimum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 900..2600 | -3000 | -2000000  

outletMaxVolMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.11
Display or set the outlet maximum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 900..2600 | -3000 | -2000000  

outletMinPMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.12
Display or set the outlet minimum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..99999 | -3000 | -2000000  

outletMaxPMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.13
Display or set the outlet maximum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..99999 | -3000 | -2000000  

outletMaxPDMT 1.3.6.1.4.1.21317.1.3.2.2.2.2.10.1.14
Display or set the outlet maximum power dissipation measurment threshold. Example: range 0.0 ~ 99999.0 represents 0~999990 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..999990 | -3000 | -2000000  

breakerStatusTable 1.3.6.1.4.1.21317.1.3.2.2.2.3.1
Display total bank value table
OBJECT-TYPE    
  SEQUENCE OF  
    BreakerStatusEntry

breakerStatusEntry 1.3.6.1.4.1.21317.1.3.2.2.2.3.1.1
Single bankValue entry containing bank info.
OBJECT-TYPE    
  BreakerStatusEntry  

breakerStatusIndex 1.3.6.1.4.1.21317.1.3.2.2.2.3.1.1.1
Index of breaker number.
OBJECT-TYPE    
  INTEGER 1..30  

breakerStatus 1.3.6.1.4.1.21317.1.3.2.2.2.3.1.1.2
Breaker status.
OBJECT-TYPE    
  INTEGER off(1), on(2), not-support(3)  

bankValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.3.2
Display total bank value table
OBJECT-TYPE    
  SEQUENCE OF  
    BankValueEntry

bankValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1
Single bankValue entry containing bank info.
OBJECT-TYPE    
  BankValueEntry  

bankValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.1
Index of bank number
OBJECT-TYPE    
  INTEGER 1..30  

bankCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.2
Bank electric current value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

bankVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.3
Bank voltage value. We put this OID to write access type for user to set the reference voltage on EC1000 model. And the setting should be the numbers. You can set 0 to clear the setting. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

bankPower 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.4
Bank power value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

bankPowerDissipation 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.5
Bank power dissipation value. If this measurement value is not available, it returns: N/A. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

bankMaxCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.6
The Bank Max Current value. unit: (A) EC1000:0A~320A
OBJECT-TYPE    
  INTEGER  

bankAttachStatus 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.7
The status of Energy sensor Bank attached status.
OBJECT-TYPE    
  INTEGER noattached(1), attached(2), error(3), noexisted(4)  

bankPowerFactor 1.3.6.1.4.1.21317.1.3.2.2.2.3.2.1.8
Bank Power Factor value. If the device does not support this OID, it returns: not-support.
OBJECT-TYPE    
  DisplayString  

bankConfigTable 1.3.6.1.4.1.21317.1.3.2.2.2.3.3
Bank configuration table
OBJECT-TYPE    
  SEQUENCE OF  
    BankConfigEntry

bankConfigEntry 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1
Bank Config entry containing Bank info.
OBJECT-TYPE    
  BankConfigEntry  

bankConfigIndex 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.1
Index of bank number
OBJECT-TYPE    
  INTEGER 1..30  

bankName 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.2
Display or set the name of bank. When this model does not support the OID, we show n/a. string length: 0~15 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

bankMinCurMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.3
Display or set the outlet minimum electric current measurment threshold. Example: range 0.0 ~16.0 rerpresnts 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

bankMaxCurMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.4
Display or set the outlet maximum electric current measurment threshold. Example: range 0.0 ~16.0 represents 0~160 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

bankMinVolMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.5
Display or set the outlet minimum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 900..2600 | -3000 | -2000000  

bankMaxVolMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.6
Display or set the outlet maximum voltage measurment threshold. Example: range 90.0 ~260.0 represents 900~2600 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 900..2600 | -3000 | -2000000  

bankMinPMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.7
Display or set the outlet minimum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..99999 | -3000 | -2000000  

bankMaxPMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.8
Display or set the outlet maximum power measurment threshold. Example: range 0.0 ~ 9999.9 represents 0~99999 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..99999 | -3000 | -2000000  

bankMaxPDMT 1.3.6.1.4.1.21317.1.3.2.2.2.3.3.1.9
Display or set the outlet maximum power dissipation measurment threshold. Example: range 0.0 ~ 99999.0 represents 0~999990 NOTICE: Minimum threshold should be smaller than maximum threshold. Empty value: -3000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER 0..999990 | -3000 | -2000000  

bankControlTable 1.3.6.1.4.1.21317.1.3.2.2.2.3.4
Bank Control table
OBJECT-TYPE    
  SEQUENCE OF  
    BankControlEntry

bankControlEntry 1.3.6.1.4.1.21317.1.3.2.2.2.3.4.1
Bank control entry.
OBJECT-TYPE    
  BankControlEntry  

bankControlIndex 1.3.6.1.4.1.21317.1.3.2.2.2.3.4.1.1
Index of bank number
OBJECT-TYPE    
  INTEGER 1..4  

bankControlStatus 1.3.6.1.4.1.21317.1.3.2.2.2.3.4.1.2
This function is used for outlet control of bank. Set off(1) to turn off for outlet control of bank. Set on(2) to turn on for all outlet control of bank. Set reboot(3) to turn on for outlet control of bank. Get this object always return nostatus(3), because there is no bank status.
OBJECT-TYPE    
  INTEGER off(1), on(2), reboot(3), nostatus(4), not-support(5)  

bankIntegerValueTable 1.3.6.1.4.1.21317.1.3.2.2.2.3.99
Display total bank value table
OBJECT-TYPE    
  SEQUENCE OF  
    BankIntegerValueEntry

bankIntegerValueEntry 1.3.6.1.4.1.21317.1.3.2.2.2.3.99.1
Single bankValue entry containing bank info.
OBJECT-TYPE    
  BankIntegerValueEntry  

bankIntegerValueIndex 1.3.6.1.4.1.21317.1.3.2.2.2.3.99.1.1
Index of bank number.
OBJECT-TYPE    
  INTEGER 1..30  

bankIntegerCurrent 1.3.6.1.4.1.21317.1.3.2.2.2.3.99.1.2
Bank electric current value. This value indicates that 1,000 times. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

bankIntegerVoltage 1.3.6.1.4.1.21317.1.3.2.2.2.3.99.1.3
Bank voltage value. This value indicates that 1,000 times. We put this OID to write access type for user to set the reference voltage on EC1000 model. And the setting should be the numbers. You can set 0 to clear the setting. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

bankIntegerPower 1.3.6.1.4.1.21317.1.3.2.2.2.3.99.1.4
Bank power value. This value indicates that 1,000 times. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

bankIntegerPowerDissipation 1.3.6.1.4.1.21317.1.3.2.2.2.3.99.1.5
Bank power dissipation value. This value indicates that 1,000 times. If this measurement value is not available, it returns value -1000000. If the device does not support this OID, it returns value -2000000.
OBJECT-TYPE    
  INTEGER  

deviceMAC 1.3.6.1.4.1.21317.1.3.2.2.3.4.1
Display device MAC address.
OBJECT-TYPE    
  DisplayString  

deviceIPv4 1.3.6.1.4.1.21317.1.3.2.2.3.4.2
Display device IP address.
OBJECT-TYPE    
  IpAddress  

deviceFWversion 1.3.6.1.4.1.21317.1.3.2.2.3.4.3
Display device FW version.
OBJECT-TYPE    
  DisplayString  

dashboardRow 1.3.6.1.4.1.21317.1.3.2.2.3.4.4.1
Display or set device's dashboard row number.
OBJECT-TYPE    
  INTEGER 1..26  

dashboardColumn 1.3.6.1.4.1.21317.1.3.2.2.3.4.4.2
Display or set device's dashboard column number.
OBJECT-TYPE    
  INTEGER 1..26  

dashboardRackName 1.3.6.1.4.1.21317.1.3.2.2.3.4.4.3
Display or set device's dashboard rack name. string length: 1~32 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

httpPort 1.3.6.1.4.1.21317.1.3.2.2.3.4.5.1
Display or set the HTTP port of PE device.
OBJECT-TYPE    
  INTEGER 1..65535  

httpsPort 1.3.6.1.4.1.21317.1.3.2.2.3.4.5.2
Display or set the HTTPs port of PE device.
OBJECT-TYPE    
  INTEGER 1..65535  

httpsOnlyEnable 1.3.6.1.4.1.21317.1.3.2.2.3.4.5.3
Enable to use Webpage HTTPs only or disable to use Webpage HTTP/HTTPs
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

staticIPEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.1
Display or set IPv4 address automatically or not
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

fixedIPv4 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.2
Display or set fixed IPv4 address
OBJECT-TYPE    
  IpAddress  

subnetMask 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.3
Display or set subnet mask address
OBJECT-TYPE    
  IpAddress  

gateway 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.4
Display or set gateway address
OBJECT-TYPE    
  IpAddress  

staticDNSEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.5
Display or set DNS address automatically or not
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

dnsPreferIPv4 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.6
Display or set prefer DNS address
OBJECT-TYPE    
  IpAddress  

dnsAlternateIPv4 1.3.6.1.4.1.21317.1.3.2.2.3.4.6.7
Display or set alternate DNS address
OBJECT-TYPE    
  IpAddress  

trapEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.1
Indicates if this trap entry is enabled or not. You should set the username/auth-password/priv-password first, when choosing snmpv3. You should set the community string first, when choosing snmpv1/v2c.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

trapVersion 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.2
Choose SNMP Trap version to send trap. You should set the username/auth-password/priv-password first, when choosing snmpv3. You should set the community string first, when choosing snmpv1/v2c.
OBJECT-TYPE    
  INTEGER v1(1), v2c(2), v3(3)  

snmpTrapTable 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3
PE SNMP agent trap setup table. If users want to use trap, they must set enable trap, ip and community first.
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpTrapEntry

snmpTrapEntry 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1
Single trap entry containing trap receiver info.
OBJECT-TYPE    
  SnmpTrapEntry  

trapReceiverNumber 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.1
Index of trap receiver
OBJECT-TYPE    
  INTEGER 1..2  

trapReceiverIPAddress 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.2
Trap receiver IP address
OBJECT-TYPE    
  IpAddress  

trapPort 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.3
NMS trap port to be used by agent to send trap
OBJECT-TYPE    
  INTEGER 1..65535  

trapCommunity 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.4
If use SNMPv1/v2c to receive trap should set this Community string. MAX string length: 20 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString Size(0..20)  

trapUsername 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.5
If use SNMPv3 to receive trap should set this string. NOTE: Input string as /empty to set this object to NULL. MAX string length: 20
OBJECT-TYPE    
  DisplayString Size(0..20)  

trapAuthpassword 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.6
If use SNMPv3 to receive trap should set this string. MAX string length: 20 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString Size(8..20)  

trapPrivpassword 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.1.3.1.7
If use SNMPv3 to receive trap should set this string. MAX string length: 20 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString Size(8..20)  

sysLogServerEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2.1
Display or set syslog server address automatically or not
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

sysLogServerIPv4 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2.2
Display or set syslog server address
OBJECT-TYPE    
  IpAddress  

sysLogServerPort 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.2.3
Display or set syslog server port
OBJECT-TYPE    
  INTEGER 1..65535  

smtpServerEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.1
Display or set SMTP server enable status.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

smtpServerName 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.2
Display or set a SMTP server name. NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

smtpAuthEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.3
Display or set authentication of SMTP server.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

smtpAccountName 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.4
Display or set a user's name of SMTP server. NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

smtpAccountPwd 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.5
Display or set a user's password of SMTP server. NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

smtpMailFrom 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.6
Display or set a mail of SMTP server. NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

smtpMailTo 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.3.7
Display or set a mail of SMTP server. NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

configurationNotifyEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.9.1
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

configurationNotifyTrapMSG 1.3.6.1.4.1.21317.1.3.2.2.3.4.7.9.2
NOTIFICATION-TYPE    

timeZoneSetting 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.1.1
Display or set the time zone of PE device. (0) [GMT-12:00] Eniwetok Kwajalein (1) [GMT-11:00] Midway Island Samoa (2) [GMT-10:00] Hawaii (3) [GMT-09:00] Alaska (4) [GMT-08:00] Pacific Time (US & Canada); Tijuana (5) [GMT-07:00] Mountain Time (US & Canada) (6) [GMT-07:00] Arizona (7) [GMT-06:00] Central Time (US & Canada) (8) [GMT-06:00] Mexico City (9) [GMT-06:00] Saskatchewan (10)[GMT-06:00] Central America (11)[GMT-05:00] Eastern Time (US & Canada) (12)[GMT-05:00] Indiana (East) (13)[GMT-05:00] Bogota Lima Quito (14)[GMT-04:00] Atlantic Time (Canada) (15)[GMT-04:00] Caracas La Paz (16)[GMT-04:00] Santiago (17)[GMT-03:30] Newfoundland (18)[GMT-03:00] Buenos Aires Georgetown (19)[GMT-03:00] Brasilia (20)[GMT-03:00] Greenland (21)[GMT-02:00] Mid-Atlantic (22)[GMT-01:00] Azores (23)[GMT-01:00] Cape Verde Is (24)[GMT] Casablanca Monrovia (25)[GMT] Greenwich Mean Time: Dublin Edinburgh Lisbon London (26)[GMT+01:00] Amsterdam Copenhagen Madrid Paris Vilnius (27)[GMT+01:00] West Central Africa (28)[GMT+01:00] Belgrade Sarajevo Skopje Sofija Zagreb (29)[GMT+01:00] Bratislava Budapest Ljubljana Prague Warsaw (30)[GMT+01:00] Brussels Berlin Bern Rome Stockholm Vienna (31)[GMT+02:00] Cairo (32)[GMT+02:00] Harare Pretoria (33)[GMT+02:00] Jerusalem (34)[GMT+02:00] Bucharest (35)[GMT+02:00] Helsinki Riga Tallinn (36)[GMT+02:00] Athens Istanbul Minsk (37)[GMT+03:00] Kuwait Riyadh (38)[GMT+03:00] Nairobi (39)[GMT+03:00] Baghdad (40)[GMT+03:00] Moscow St. Petersburg Volgograd (41)[GMT+03:30] Tehran (42)[GMT+04:00] Abu Dhabi Muscat (43)[GMT+04:00] Baku Tbilisi Yerevan (44)[GMT+04:30] Kabul (45)[GMT+05:00] Islamabad Karachi Tashkent (46)[GMT+05:00] Ekaterinburg (47)[GMT+05:30] Calcutta Chennai Mumbai New Delhi (48)[GMT+05:45] Kathmandu (49)[GMT+06:00] Astana Dhaka (50)[GMT+06:00] Sri Jayawardenepura (51)[GMT+06:00] Almaty Novosibirsk (52)[GMT+06:30] Rangoon (53)[GMT+07:00] Bangkok Hanoi Jakarta (54)[GMT+07:00] Krasnoyarsk (55)[GMT+08:00] Beijing Chongqing Hong Kong Urumqi (56)[GMT+08:00] Perth (57)[GMT+08:00] Kuala Lumpur Singapore (58)[GMT+08:00] Taipei (59)[GMT+08:00] Irkutsk Ulaan Bataar (60)[GMT+09:00] Osaka Sapporo Tokyo (61)[GMT+09:00] Seoul (62)[GMT+09:00] Yakutsk (63)[GMT+09:30] Darwin (64)[GMT+09:30] Adelaide (65)[GMT+10:00] Canberra Melbourne Sydney (66)[GMT+10:00] Brisbane (67)[GMT+10:00] Guam Port Moresby (68)[GMT+10:00] Hobart (69)[GMT+10:00] Vladivostok (70)[GMT+11:00] Magadan Solomon Is New Caledonia (71)[GMT+12:00] Fiji Kamchatka Marshall Is. (72)[GMT+12:00] Auckland Wellington (73)[GMT+13:00] Nuku'alofa
OBJECT-TYPE    
  INTEGER  

dstEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.1.2
Display or set daylight savings time .
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

dateSetting 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.2.1
Display or set date in a manual way.(This is Greenwich Mean Time, GMT) string length: 10 This value format must match the following form: YYYY-MM-DD ex. 2011-01-01 Note: range of year: 2000-2099 range of month: 01-12 range of day: 01-31
OBJECT-TYPE    
  DisplayString  

timeSetting 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.2.2
Display or set time in a manual way.(This is Greenwich Mean Time, GMT) string length: 8 This value format must match the following form: HH:MM:SS ex. 02:02:02 Note: range of hour: 00-24 range of minute: 00-60 range of second: 00-60
OBJECT-TYPE    
  DisplayString  

autoAdjustEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.1
Display or set date time useing auto adjustment way.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

preferNTP 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.2
Display or set prefer NTP server. AU | ntp1.cs.mu.OZ.AU(0), AU | ntp0.cs.mu.OZ.AU(1), BE | ntp2.oma.be(2), BE | ntp1.oma.be(3), BR | ntps1.pads.ufrj.br(4), CH | swisstime.ethz.ch(5), CL | ntp.shoa.cl(6), CZ | ntp.nic.cz(7), DE | ntp.stairweb.de(8), DE | ntps1-0.cs.tu-berlin.de(9), DE | ptbtime1.ptb.de(10), DE | ntp1.fau.de(11), DE | ptbtime2.ptb.de(12), DE | time1.one4vision.de(13), DE | rustime01.rus.uni-stuttgart.de(14), DE | ntp.probe-networks.de(15), DE | ntp2.fau.de(16), ES | hora.roa.es(17), HK | stdtime.gov.hk(18), IE | ntp-galway.hea.net(19), IT | ntp1.inrim.it(20), IT | ntp2.inrim.it(21), JP | clock.tl.fukuoka-u.ac.jp(22), JP | ntp.nict.jp(23), JP | clock.nc.fukuoka-u.ac.jp(24), KR | ntp.xbsd.kr(25), MX | cronos.cenam.mx(26), NL | ntp0.nl.uu.net(27), NL | ntp1.nl.uu.net(28), NL | ntp.remco.org(29), NL | ntp0.nl.net(30), PL | vega.cbk.poznan.pl(31), PL | ntp.ntp-servers.com(32), RO | ntp3.usv.ro(33), RO | ntp2.usv.ro(34), RU | ntp1.vniiftri.ru; ntp1.imvp.ru(35), RU | ntp2.vniiftri.ru; ntp2.imvp.ru(36), SE | ntp1.mmo.netnod.se(37), SE | ntp1.sth.netnod.se(38), SE | ntp2.mmo.netnod.se(39), SE | ntp2.sth.netnod.se(40), SE | time2.stupi.se(41), SE | ntp1.sp.se(42), SE | timehost.lysator.liu.se(43), SI | ntp.mostovna.com(44), US CA | timekeeper.isi.edu(45), US CA | clock.sjc.he.net(46), US CA | nist1.symmetricom.com(47), US CA | clock.via.net(48), US CA | nist1.aol-ca.truetime.com(49), US CA | clock.isc.org(50), US CA | clepsydra.dec.com(51), US CA | gps.layer42.net(52), US CA | time.no-such-agency.net(53), US CA | nist1-sj.WiTime.net(54), US CA | clock.fmt.he.net(55), US CO | time-b.timefreq.bldrdoc.gov(56), US CO | time-a.timefreq.bldrdoc.gov(57), US CO | utcnist.colorado.edu(58), US CO | time-c.timefreq.bldrdoc.gov(59), US DE | rackety.udel.edu(60), US DE | mizbeaver.udel.edu(61), US GA | nist1.columbiacountyga.gov(62), US IL | ntp.your.org(63), US MA | bonehed.lcs.mit.edu(64), US MA | time.keneli.org(65), US MA | ntp0.broad.mit.edu(66), US MD | time-a.nist.gov(67), US MD | time-b.nist.gov(68), US MI | nist.netservicesgroup.com(69), US NY | nist1-ny.WiTime.net(70), US NY | clock.nyc.he.net(71), US UT | time.xmission.com(72), US VA | nist1-dc.WiTime.net(73), US VA | nist1.aol-va.truetime.com(74), US WA | time-nw.nist.gov(75), FR | utp.univ-lyon1.fr(76), FR | ntp-sop.inria.fr(77), FR | ntp.tuxfamily.net(78), UK | bear.zoo.bt.co.uk(79)
OBJECT-TYPE    
  INTEGER  

preferServerIPenable 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.3
Enable or disable prefer custom server IP.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

preferNTPIp 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.4
Display or set prefer NTP server IP.
OBJECT-TYPE    
  IpAddress  

alternateNtpEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.5
Display or set date time using alternate NTP server.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

alternateNtp 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.6
Display or set alternative NTP server. AU | ntp1.cs.mu.OZ.AU(0), AU | ntp0.cs.mu.OZ.AU(1), BE | ntp2.oma.be(2), BE | ntp1.oma.be(3), BR | ntps1.pads.ufrj.br(4), CH | swisstime.ethz.ch(5), CL | ntp.shoa.cl(6), CZ | ntp.nic.cz(7), DE | ntp.stairweb.de(8), DE | ntps1-0.cs.tu-berlin.de(9), DE | ptbtime1.ptb.de(10), DE | ntp1.fau.de(11), DE | ptbtime2.ptb.de(12), DE | time1.one4vision.de(13), DE | rustime01.rus.uni-stuttgart.de(14), DE | ntp.probe-networks.de(15), DE | ntp2.fau.de(16), ES | hora.roa.es(17), HK | stdtime.gov.hk(18), IE | ntp-galway.hea.net(19), IT | ntp1.inrim.it(20), IT | ntp2.inrim.it(21), JP | clock.tl.fukuoka-u.ac.jp(22), JP | ntp.nict.jp(23), JP | clock.nc.fukuoka-u.ac.jp(24), KR | ntp.xbsd.kr(25), MX | cronos.cenam.mx(26), NL | ntp0.nl.uu.net(27), NL | ntp1.nl.uu.net(28), NL | ntp.remco.org(29), NL | ntp0.nl.net(30), PL | vega.cbk.poznan.pl(31), PL | ntp.ntp-servers.com(32), RO | ntp3.usv.ro(33), RO | ntp2.usv.ro(34), RU | ntp1.vniiftri.ru; ntp1.imvp.ru(35), RU | ntp2.vniiftri.ru; ntp2.imvp.ru(36), SE | ntp1.mmo.netnod.se(37), SE | ntp1.sth.netnod.se(38), SE | ntp2.mmo.netnod.se(39), SE | ntp2.sth.netnod.se(40), SE | time2.stupi.se(41), SE | ntp1.sp.se(42), SE | timehost.lysator.liu.se(43), SI | ntp.mostovna.com(44), US CA | timekeeper.isi.edu(45), US CA | clock.sjc.he.net(46), US CA | nist1.symmetricom.com(47), US CA | clock.via.net(48), US CA | nist1.aol-ca.truetime.com(49), US CA | clock.isc.org(50), US CA | clepsydra.dec.com(51), US CA | gps.layer42.net(52), US CA | time.no-such-agency.net(53), US CA | nist1-sj.WiTime.net(54), US CA | clock.fmt.he.net(55), US CO | time-b.timefreq.bldrdoc.gov(56), US CO | time-a.timefreq.bldrdoc.gov(57), US CO | utcnist.colorado.edu(58), US CO | time-c.timefreq.bldrdoc.gov(59), US DE | rackety.udel.edu(60), US DE | mizbeaver.udel.edu(61), US GA | nist1.columbiacountyga.gov(62), US IL | ntp.your.org(63), US MA | bonehed.lcs.mit.edu(64), US MA | time.keneli.org(65), US MA | ntp0.broad.mit.edu(66), US MD | time-a.nist.gov(67), US MD | time-b.nist.gov(68), US MI | nist.netservicesgroup.com(69), US NY | nist1-ny.WiTime.net(70), US NY | clock.nyc.he.net(71), US UT | time.xmission.com(72), US VA | nist1-dc.WiTime.net(73), US VA | nist1.aol-va.truetime.com(74), US WA | time-nw.nist.gov(75), FR | utp.univ-lyon1.fr(76), FR | ntp-sop.inria.fr(77), FR | ntp.tuxfamily.net(78), UK | bear.zoo.bt.co.uk(79)
OBJECT-TYPE    
  INTEGER  

alternateServerIPenable 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.7
Enable or disable alternate custom server IP.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

alternateNtpIp 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.8
Display or set alternative NTP server IP.
OBJECT-TYPE    
  IpAddress  

adjustTimeEveryDays 1.3.6.1.4.1.21317.1.3.2.2.3.4.8.3.9
Display or set frequency of adjustment in days.
OBJECT-TYPE    
  INTEGER  

loginAllowTimes 1.3.6.1.4.1.21317.1.3.2.2.3.5.1.1
Display or set time of login faliure.
OBJECT-TYPE    
  INTEGER 1..99  

loginTimeOut 1.3.6.1.4.1.21317.1.3.2.2.3.5.1.2
Display or set login time out.
OBJECT-TYPE    
  INTEGER 1..240  

icmpEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.2.1
Display or set status of ICMP.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

minUserNameLen 1.3.6.1.4.1.21317.1.3.2.2.3.5.3.1
Display or set minimum length of user name.
OBJECT-TYPE    
  INTEGER 1..16  

minUserPwdLen 1.3.6.1.4.1.21317.1.3.2.2.3.5.3.2
Display or set minimum length of user password.
OBJECT-TYPE    
  INTEGER 1..16  

upperCaseEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.3.3
Display or set one upper case rule in user password.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

lowerCaseEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.3.4
Display or set one lower case rule in user password.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

numberEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.3.5
Display or set one number rule in user password.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

disableDuplicateLogin 1.3.6.1.4.1.21317.1.3.2.2.3.5.3.6
Display or set status of disabled duplicate login rule.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

loginString 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.1
Display or set a login string. string length: 0~32 NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

ipFilterEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.1
Display or set status of ip filter.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipFilterRule 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.2
Display or set status of ip filter rule.
OBJECT-TYPE    
  INTEGER include(1), exclude(2)  

ipFilterTable 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3
A list of restricted ip.
OBJECT-TYPE    
  SEQUENCE OF  
    IpFilterEntry

ipFilterEntry 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1
Status and parameter values for a PE's restricted IP.
OBJECT-TYPE    
  IpFilterEntry  

ipFilterIndex 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1.1
The value of index for the ip filter.
OBJECT-TYPE    
  INTEGER 1..5  

ipFilterFrom 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1.2
A set of restricted ip. ex. 192.168.0.1 Note: Users must follow in order to set the ip address. Note: To clear the settings to set the ip 0.0.0.0
OBJECT-TYPE    
  IpAddress  

ipFilterTo 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.2.3.1.3
A set of restricted ip. ex. 192.168.0.255 Note: Users must follow in order to set the ip address. Note: To clear the settings to set the ip 0.0.0.0
OBJECT-TYPE    
  IpAddress  

macFilterEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.1
Display or set status of mac filter.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

macFilterRule 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.2
Display or set status of mac filter rule.
OBJECT-TYPE    
  INTEGER include(1), exclude(2)  

macFilterTable 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3
A list of restricted mac.
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterEntry

macFilterEntry 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3.1
Status and parameter values for a PE's restricted MAC.
OBJECT-TYPE    
  MacFilterEntry  

macFilterIndex 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3.1.1
The value of index for the mac filter.
OBJECT-TYPE    
  INTEGER 1..5  

macFilterSet 1.3.6.1.4.1.21317.1.3.2.2.3.5.4.3.3.1.2
A set of restricted mac. string length: 12 ex. 004854655511 Note: Users must follow in order to set the MAC address. Note: To clear the settings to set the MAC 000000000000
OBJECT-TYPE    
  DisplayString  

radiusEnabled 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.1
Display or set status of RADIUS server.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

preferRadiusIp 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.2
Display or set prefer RADIUS server IP.
OBJECT-TYPE    
  IpAddress  

preferRadiusPort 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.3
Display or set prefer RADIUS server port.
OBJECT-TYPE    
  INTEGER 1..65535  

alternateRadiusIp 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.4
Display or set alternative RADIUS server IP.
OBJECT-TYPE    
  IpAddress  

alternateRadiusPort 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.5
Display or set alternative RADIUS server port.
OBJECT-TYPE    
  INTEGER 1..65535  

radiusTimeOut 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.6
Display or set time out of authentication using RADIUS server. The unit is sec.
OBJECT-TYPE    
  INTEGER 1..60  

radiusRetry 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.7
Display or set retry times of authentication using RADIUS server.
OBJECT-TYPE    
  INTEGER 0..10  

radiusSecret 1.3.6.1.4.1.21317.1.3.2.2.3.5.5.1.8
Display or set shared secret of RADIUS server. string length: 6~15 At least 6 characters. NOTE: Input string as /empty to set this object to NULL.
OBJECT-TYPE    
  DisplayString  

usrListTable 1.3.6.1.4.1.21317.1.3.2.2.1.1
A list of user. The number of user is given by the value of usrcfgNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    UsrListEntry

usrListEntry 1.3.6.1.4.1.21317.1.3.2.2.1.1.1
Status and parameter values for a pe8208 user.
OBJECT-TYPE    
  UsrListEntry  

usrIndex 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.1
The value of usrIndex for the user. We have 1 administrator and 8 users. The index 9 will be the administrator.
OBJECT-TYPE    
  INTEGER 1..9  

usrType 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.2
The user's type.
OBJECT-TYPE    
  INTEGER administrator(1), user(2)  

usrName 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.3
A textual string containing name of the user. string length: 1~16
OBJECT-TYPE    
  DisplayString Size(1..16)  

usrPassword 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.4
A textual string containing password of the user. string length: 1~16
OBJECT-TYPE    
  DisplayString Size(1..16)  

usrPort1Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.5
Display or set this user's outlet 1 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort2Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.6
Display or set this user's outlet 2 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort3Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.7
Display or set this user's outlet 3 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort4Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.8
Display or set this user's outlet 4 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort5Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.9
Display or set this user's outlet 5 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort6Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.10
Dispaly or set this user's outlet 6 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort7Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.11
Display or set this user's outlet 7 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort8Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.12
Display or set this user's outlet 8 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrEnable 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.47
Display or set this user is enable or not
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

usrPort9Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.13
Display or set this user's outlet 9 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort10Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.14
Display or set this user's outlet 10 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort11Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.15
Display or set this user's outlet 11 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort12Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.16
Display or set this user's outlet 12 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort13Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.17
Display or set this user's outlet 13 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort14Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.18
Display or set this user's outlet 14 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort15Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.19
Display or set this user's outlet 15 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort16Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.20
Display or set this user's outlet 16 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort17Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.21
Display or set this user's outlet 17 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort18Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.22
Display or set this user's outlet 18 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort19Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.23
Display or set this user's outlet 19 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort20Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.24
Display or set this user's outlet 20 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort21Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.25
Display or set this user's outlet 21 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort22Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.26
Display or set this user's outlet 22 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort23Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.27
Display or set this user's outlet 23 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort24Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.28
Display or set this user's outlet 24 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort25Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.29
Display or set this user's outlet 25 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort26Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.30
Display or set this user's outlet 26 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort27Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.31
Display or set this user's outlet 27 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort28Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.32
Display or set this user's outlet 28 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort29Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.33
Display or set this user's outlet 29 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort30Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.34
Display or set this user's outlet 30 authority. Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort31Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.35
Display or set this user's outlet 31 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort32Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.36
Display or set this user's outlet 32 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort33Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.37
Display or set this user's outlet 33 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort34Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.38
Display or set this user's outlet 34 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort35Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.39
Display or set this user's outlet 35 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort36Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.40
Display or set this user's outlet 36 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort37Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.41
Display or set this user's outlet 37 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort38Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.42
Display or set this user's outlet 38 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort39Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.43
Display or set this user's outlet 39 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort40Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.44
Display or set this user's outlet 40 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort41Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.45
Display or set this user's outlet 41 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

usrPort42Auth 1.3.6.1.4.1.21317.1.3.2.2.1.1.1.46
Display or set this user's outlet 42 authority Port in the pe of series represents outlet. Port in the Energy monitor of series represents a bank or a pdu.
OBJECT-TYPE    
  INTEGER disable(1), view(2), modify(3), not-support(4)  

customTrapMSG 1.3.6.1.4.1.21317.1.3.2.2.5
Display custom trap message.
NOTIFICATION-TYPE    

rebootDevice 1.3.6.1.4.1.21317.1.3.2.2.6
Reboot PE Device
OBJECT-TYPE    
  INTEGER no(1), yes(2)