AT-UWC-WLAN-SWITCH-MIB

File: AT-UWC-WLAN-SWITCH-MIB.mib (656911 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC AT-SMI-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Integer32 Unsigned32
Counter32 Counter64 TimeTicks
RowStatus TruthValue DisplayString
MacAddress TimeStamp TEXTUAL-CONVENTION
wirelesslan atUWC

Defined Types

WsOui  
24-bit Organizationally Unique Identifier. Information on OUIs can be found in IEEE 802-2001 [802-2001] Clause 9.
TEXTUAL-CONVENTION    
  OCTET STRING Size(3)  

TspecSuppAC  
Access category (AC) used for TSPEC. Only those ACs that support mandatory admission control are listed here.
TEXTUAL-CONVENTION    
  INTEGER voice(0), video(1)  

WsValidAPConfigEntry  
SEQUENCE    
  wsAPMacAddress MacAddress
  wsAPLocation DisplayString
  wsAPMode INTEGER
  wsAPAuthenticationPasswd DisplayString
  wsUseAPProfileId Integer32
  wsAPRadio1Channel Integer32
  wsAPRadio2Channel Integer32
  wsAPRadio1TxPower Integer32
  wsAPRadio2TxPower Integer32
  wsAPStandaloneExpectedChannel Integer32
  wsAPStandaloneExpectedSecurity INTEGER
  wsAPStandaloneExpectedSsid DisplayString
  wsAPStandaloneExpectedWds INTEGER
  wsAPStandaloneExpectedWired INTEGER
  wsAPConfigRowStatus RowStatus

WsKnownClientEntry  
SEQUENCE    
  wsKnownClientMacAddress MacAddress
  wsKnownClientAuthAction INTEGER
  wsKnownClientName DisplayString
  wsKnownClientRowStatus RowStatus

WsSwitchStatusEntry  
SEQUENCE    
  wsSwitchIPAddress IpAddress
  wsSwitchClusterPriority Unsigned32
  wsSwitchAPImageDownloadMode DisplayString
  wsSwitchTotalAPs Unsigned32
  wsSwitchManagedAPs Unsigned32
  wsSwitchDiscoveredAPs Unsigned32
  wsSwitchConnectionFailedAPs Unsigned32
  wsSwitchMaximumManagedAPs Unsigned32
  wsSwitchTotalClients Unsigned32
  wsSwitchAuthenticatedClients Unsigned32
  wsSwitchWLANUtilization Unsigned32
  wsSwitchDistTunnelClients Unsigned32

WsSwitchStatisticsEntry  
SEQUENCE    
  wsSwitchWLANBytesTransmitted Counter64
  wsSwitchWLANBytesReceived Counter64
  wsSwitchWLANPktsTransmitted Counter64
  wsSwitchWLANPktsReceived Counter64
  wsSwitchWLANBytesTransmitDropped Counter64
  wsSwitchWLANBytesRecvDropped Counter64
  wsSwitchWLANPktsTransmitDropped Counter64
  wsSwitchWLANPktsRecvDropped Counter64

WsIPPollListEntry  
SEQUENCE    
  wsPollIpAddress IpAddress
  wsPollIPStatus INTEGER
  wsIPPollRowStatus RowStatus

WsL2DiscoveryVlanListEntry  
SEQUENCE    
  wsL2DiscoveryVlanId Integer32
  wsL2DiscoveryVlanRowStatus RowStatus

WsL2CentTnnlVlanListEntry  
SEQUENCE    
  wsL2CentTnnlVlanId Integer32
  wsL2CentTnnlVlanRowStatus RowStatus

WsOuiEntry  
SEQUENCE    
  wsOuiValue WsOui
  wsOuiDescription DisplayString
  wsOuiRowStatus RowStatus

WsAPProfileEntry  
SEQUENCE    
  wsAPProfileId Integer32
  wsAPProfileName DisplayString
  wsAPProfileState INTEGER
  wsAPProfileRowStatus RowStatus
  wsCopyAPProfileToProfileId Integer32
  wsAPProfileApply INTEGER
  wsAPHardwareTypeID Integer32
  wsAPWiredDetectionVlanId Integer32
  wsAPProfileDisconnAPFwdingMode INTEGER
  wsAPProfileDisconnAPMgmtMode INTEGER
  wsAPProfileAeroScoutSupportMode INTEGER

WsAPProfileRadioEntry  
SEQUENCE    
  wsAPRadioInterface Integer32
  wsAPRadioAdminMode INTEGER
  wsAPRadioFrequency INTEGER
  wsAPRadioOtherChannelsScanMode INTEGER
  wsAPRadioOtherChannelsScanInterval Integer32
  wsAPRadioSentryScanMode INTEGER
  wsAPRadioSentryScanChannel INTEGER
  wsAPRadioScanDuration Integer32
  wsAPRadioRateLimitMode INTEGER
  wsAPRadioRateLimit Integer32
  wsAPRadioRateLimitBurst Integer32
  wsAPRadioBeaconInterval Integer32
  wsAPRadioDTIMPeriod Integer32
  wsAPRadioFragmentationThreshold Integer32
  wsAPRadioRTSThreshold Integer32
  wsAPRadioShortRetryLimit Integer32
  wsAPRadioLongRetryLimit Integer32
  wsAPRadioMaxTransmitLifetime Unsigned32
  wsAPRadioMaxReceiveLifetime Unsigned32
  wsAPRadioMaxClients Integer32
  wsAPRadioAutoPowerMode INTEGER
  wsAPRadioTxPower Integer32
  wsAPRadioWMMMode INTEGER
  wsAPRadioLoadBalancingMode INTEGER
  wsAPRadioUtilization Integer32
  wsAPRadioAutoChannelMode INTEGER
  wsAPRadioStationIsolationMode INTEGER
  wsAPRadioChannelBandwidth INTEGER
  wsAPRadioPrimaryChannel INTEGER
  wsAPRadioProtectionMode INTEGER
  wsAPRadioShortGuardInterval INTEGER
  wsAPRadioSTBCMode INTEGER
  wsAPRadioMulticastTxRate Integer32
  wsAPRadioAPSDMode INTEGER
  wsAPRadioNoAckMode INTEGER
  wsAPRadioResourceMeasEnabled INTEGER
  wsAPRadioQOSEDCATemplate INTEGER
  wsAPRadioMinTxPower Integer32

WsAPProfileRadioSupportedRatesEntry  
SEQUENCE    
  wsSupportedDataRate Integer32
  wsAPProfileRadioSupportedDataMode INTEGER

WsAPProfileRadioBasicRatesEntry  
SEQUENCE    
  wsBasicDataRate Integer32
  wsAPProfileRadioBasicDataMode INTEGER

WsAPProfileVAPEntry  
SEQUENCE    
  wsVAPId Integer32
  wsVAPMode INTEGER
  wsVAPNetworkId Integer32

WsAPProfileQOSEntry  
SEQUENCE    
  wsQOSQueueId INTEGER
  wsAPEDCAAIFS Integer32
  wsAPEDCAMinContentionWindow INTEGER
  wsAPEDCAMaxContentionWindow INTEGER
  wsAPEDCAMaxBurst Integer32
  wsStationEDCAAIFS Integer32
  wsStationEDCAMinContentionWindow INTEGER
  wsStationEDCAMaxContentionWindow INTEGER
  wsStationEDCATXOPLimit Integer32

WsNetworkEntry  
SEQUENCE    
  wsNetworkId Integer32
  wsNetworkIdRowStatus RowStatus
  wsNetworkSSID DisplayString
  wsNetworkDefaultVLANId Integer32
  wsNetworkHideSSIDMode INTEGER
  wsNetworkDenyBcastMode INTEGER
  wsNetworkMACAuthenticationMode INTEGER
  wsNetworkRadiusAccountingMode INTEGER
  wsNetworkSecurityMode INTEGER
  wsNetworkWPAVersionsSupported INTEGER
  wsNetworkWPACipherSuites INTEGER
  wsNetworkWPAKeyType INTEGER
  wsNetworkWPAKey DisplayString
  wsNetworkWPA2PreAuthenticationMode INTEGER
  wsNetworkWPA2PreAuthenticationLimit Integer32
  wsNetworkWPA2RoambackKeyCacheHoldtime Integer32
  wsNetworkStaticWEPAuthenticationMode INTEGER
  wsNetworkUseWEPTransferKeyIndex Integer32
  wsNetworkWEPKeyType INTEGER
  wsNetworkWEPKeyLength INTEGER
  wsNetworkWEPKey1 DisplayString
  wsNetworkWEPKey2 DisplayString
  wsNetworkWEPKey3 DisplayString
  wsNetworkWEPKey4 DisplayString
  wsClearNetworkEntry INTEGER
  wsNetworkRedirectMode INTEGER
  wsNetworkRedirectURL DisplayString
  wsIfNumber Integer32
  wsNetworkAuthRadiusServerName DisplayString
  wsNetworkAuthRadiusServerConfiguredStatus INTEGER
  wsNetworkAcctRadiusServerName DisplayString
  wsNetworkAcctRadiusServerConfiguredStatus INTEGER
  wsUseNetworkRadiusConfig INTEGER
  wsNetworkDistTunnelMode INTEGER
  wsNetworkBcastKeyRefreshRate Unsigned32
  wsNetworkSessionKeyRefreshRate Unsigned32
  wsNetworkARPSuppressionMode INTEGER
  wsNetworkBandSteerMode INTEGER

WsNetworkClientQosEntry  
SEQUENCE    
  wsNetworkClientQosBandwidthLimitDown Unsigned32
  wsNetworkClientQosBandwidthLimitUp Unsigned32
  wsNetworkClientQosAccessControlDownType INTEGER
  wsNetworkClientQosAccessControlDownName DisplayString
  wsNetworkClientQosAccessControlUpType INTEGER
  wsNetworkClientQosAccessControlUpName DisplayString
  wsNetworkClientQosDiffservPolicyDownType INTEGER
  wsNetworkClientQosDiffservPolicyDownName DisplayString
  wsNetworkClientQosDiffservPolicyUpType INTEGER
  wsNetworkClientQosDiffservPolicyUpName DisplayString
  wsNetworkClientQosMode INTEGER

WsAPProfileRadioSupportedChannelsEntry  
SEQUENCE    
  wsSupportedChannel Integer32

WsAPProfileRadioEligibleChannelsEntry  
SEQUENCE    
  wsEligibleChannel Integer32
  wsEligibleChannelRowStatus RowStatus

WsAPProfileRadioTspecEntry  
SEQUENCE    
  wsAPRadioTspecMode INTEGER
  wsAPRadioTspecVoiceAcmMode INTEGER
  wsAPRadioTspecVideoAcmMode INTEGER
  wsAPRadioTspecVoiceAcmLimit Unsigned32
  wsAPRadioTspecVideoAcmLimit Unsigned32
  wsAPRadioTspecRoamReserveLimit Unsigned32
  wsAPRadioTspecApInactivityTimeout Unsigned32
  wsAPRadioTspecStaInactivityTimeout Unsigned32
  wsAPRadioTspecLegacyWmmQueueMapMode INTEGER

WsAPProfileRadioMCSIndexEntry  
SEQUENCE    
  wsAPRadioMCSIndexValue Unsigned32
  wsAPRadioMCSIndexAvailable INTEGER

WsAPImageTypeFileEntry  
SEQUENCE    
  wsAPImageFilePath DisplayString
  wsAPImageFileName DisplayString

WsChannelPlanEntry  
SEQUENCE    
  wsChannelPlan INTEGER
  wsChannelPlanMode INTEGER
  wsChannelPlanInterval Integer32
  wsChannelPlanTime Integer32
  wsChannelPlanHistoryDepth Integer32
  wsChannelPlanOperatingStatus INTEGER
  wsChannelPlanLastIterationStatus Integer32
  wsChannelPlanManualAction INTEGER
  wsChannelPlanManualStatus INTEGER
  wsChannelPlanLastAlgorithmTime DisplayString
  wsChannelPlanChangeThreshold Integer32
  wsChannelPlanChangeThresholdAdj Integer32
  wsChannelPlanIgnoreUnamangedAPs INTEGER
  wsChannelPlanRunOnManagedApFailure INTEGER
  wsChannelPlanManagedAPFailureInterval Integer32
  wsChannelPlanNumOfRadios Integer32
  wsChannelPlanNumOfRadiosAnalysed Integer32
  wsChannelPlanNumOfRadiosScanned Integer32
  wsChannelPlanNumOfRadiosChanged Integer32
  wsChannelPlanNumOfRadiosChangedToOrigChannel Integer32
  wsChannelPlanEstimatedTimeOfCompletion DisplayString
  wsChannelPlanPercentageComplete Integer32

WsChannelPlanHistoryEntry  
SEQUENCE    
  wsChannelPlanHistory INTEGER
  wsChannelPlanAPMacAddress MacAddress
  wsChannelPlanAPRadioInterface Integer32
  wsChannelPlanAPLocation DisplayString
  wsChannelPlanAPHistoryIteration Integer32
  wsChannelPlanAPChannel Integer32

WsChannelPlanManualProposedAdjustmentEntry  
SEQUENCE    
  wsChannelPlanManual INTEGER
  wsChannelPlanManualMacAddress MacAddress
  wsChannelPlanManualAPRadioInterface Integer32
  wsChannelPlanManualCurrentChannel Integer32
  wsChannelPlanManualNewChannel Integer32

WsPowerManualProposedAdjustmentEntry  
SEQUENCE    
  wsPowerManualProposedAdjustmentAPMacAddress MacAddress
  wsPowerManualProposedAdjustmentAPRadioInterface Integer32
  wsPowerManualProposedAdjustmentAPCurrentTxPower Integer32
  wsPowerManualProposedAdjustmentAPNewTxPower Integer32

WsChannelPlanPerRadioPerBandEntry  
SEQUENCE    
  wsChannelPlanType INTEGER
  wsChannelPlanAPMacAddr MacAddress
  wsChannelPlanAPRadioIntf Integer32
  wsChannelPlanAPIsLocal INTEGER
  wsChannelPlanAPCurrentChannel Integer32
  wsChannelPlanAPOldChannel Integer32
  wsChannelPlanAPStrongestOldSignal DisplayString
  wsChannelPlanAPStrongestNewSignal DisplayString
  wsChannelPlanAPChannelChangeInd INTEGER
  wsChannelPlanAPReasonCode INTEGER
  wsChannelPlanAPStrongestOldManagedAPandSignal DisplayString
  wsChannelPlanAPStrongestNewManagedAPandSignal DisplayString
  wsChannelPlanAPStrongestOldUnmanagedAPandSignal DisplayString
  wsChannelPlanAPStrongestNewUnmanagedAPandSignal DisplayString
  wsChannelPlanAPTimeSinceLastChannelChange DisplayString
  wsChannelPlanAPLastChanScanDuration Integer32

WsPowerPlanPerRadioEntry  
SEQUENCE    
  wsPowerPlanAPMacAddress MacAddress
  wsPowerPlanAPRadioInterface Integer32
  wsPowerPlanAPIsLocal INTEGER
  wsPowerPlanAPChannel DisplayString
  wsPowerPlanAPTxPower Integer32
  wsPowerPlanAPNumInterferingAPs Integer32
  wsPowerPlanAPNumInterferingVAPs Integer32
  wsPowerPlanAPStrongestDetectorAP MacAddress
  wsPowerPlanAPStrongestDetectorRadio Integer32
  wsPowerPlanAPStrongestDetectorSignal DisplayString
  wsPowerPlanAPStrongestDetectedNeighbor MacAddress
  wsPowerPlanAPStrongestDetectedSignal DisplayString
  wsPowerPlanAPLastPwrAdjStatus INTEGER
  wsPowerPlanAPLastPwrAdjReasonCode INTEGER
  wsPowerPlanAPNumPwrChanges Integer32
  wsPowerPlanAPNumPwrInc Integer32
  wsPowerPlanAPNumPwrDec Integer32

WsPowerPlanPerProfileEntry  
SEQUENCE    
  wsPowerPlanProfileId Integer32
  wsPowerPlanPerProfileAvgNumInterferingAPs Integer32
  wsPowerPlanPerProfileAvgNumInterferingVAPs Integer32
  wsPowerPlanNumPwrChanges Integer32
  wsPowerPlanNumPwrInc Integer32
  wsPowerPlanNumPwrDec Integer32

WsManagedAPStatusEntry  
SEQUENCE    
  wsManagedAPMacAddress MacAddress
  wsManagedAPIpAddress IpAddress
  wsManagedAPVendorId Integer32
  wsManagedAPSoftwareVersion DisplayString
  wsManagedAPHWType Integer32
  wsManagedAPSerialNumber DisplayString
  wsManagedAPPartNumber DisplayString
  wsManagedAPDiscoveryReason INTEGER
  wsManagedAPStatus INTEGER
  wsManagedAPAuthenticatedClients Unsigned32
  wsManagedAPSysUpTime TimeTicks
  wsManagedAPProfileId Integer32
  wsManagedAPProfileName DisplayString
  wsManagedAPProtocolVersion Integer32
  wsManagedAPCodeDownloadStatus INTEGER
  wsManagedAPLocation DisplayString
  wsManagedAPLastFailingConfigElement Integer32
  wsManagedAPConfigFailureErrMsg DisplayString
  wsManagedAPReset INTEGER
  wsManagedAPResetStatus INTEGER
  wsManagedAPFailedEntryPurge INTEGER
  wsManagedAPDebugPassword DisplayString
  wsManagedAPDebugMode INTEGER
  wsManagedAPDebugStatus INTEGER
  wsManagedAPAge TimeTicks
  wsManagedAPManagingSwitch INTEGER
  wsManagedAPSwitchMacAddress MacAddress
  wsManagedAPSwitchIpAddress IpAddress
  wsManagedAPIpMask IpAddress
  wsManagedAPDistTunnelHomeAPClients Unsigned32
  wsManagedAPDistTunnelAssocAPClients Unsigned32
  wsManagedAPDistTunnelsTotal Unsigned32
  wsManagedAPDistTunnelsMaxMcastRepl Unsigned32
  wsManagedAPDistTunnelsMaxVlanMcastRepl Unsigned32

WsManagedAPStatisticsEntry  
SEQUENCE    
  wsManagedAPWLANPktsRecvd Counter64
  wsManagedAPWLANBytesRecvd Counter64
  wsManagedAPWLANPktsTransmitted Counter64
  wsManagedAPWLANBytesTransmitted Counter64
  wsManagedAPEthernetPktsRecvd Counter64
  wsManagedAPEthernetBytesRecvd Counter64
  wsManagedAPEthernetMcastPktsRecvd Counter64
  wsManagedAPEthernetPktsTransmitted Counter64
  wsManagedAPEthernetBytesTransmitted Counter64
  wsManagedAPEthernetTransmitErrorCount Counter64
  wsManagedAPEthernetRecvdErrorCount Counter64
  wsManagedAPCL2TunnelBytesRecvd Counter64
  wsManagedAPCL2TunnelPktsRecvd Counter64
  wsManagedAPCL2TunnelMcastRecvd Counter64
  wsManagedAPCL2TunnelBytesTransmitted Counter64
  wsManagedAPCL2TunnelPktsTransmitted Counter64
  wsManagedAPCL2TunnelMcastTransmitted Counter64
  wsManagedAPWLANPktsRecvDropped Counter64
  wsManagedAPWLANBytesRecvDropped Counter64
  wsManagedAPWLANPktsTransmitDropped Counter64
  wsManagedAPWLANBytesTransmitDropped Counter64
  wsManagedAPDistTunnelBytesTransmitted Counter64
  wsManagedAPDistTunnelBytesReceived Counter64
  wsManagedAPDistTunnelPacketsTransmitted Counter64
  wsManagedAPDistTunnelPacketsReceived Counter64
  wsManagedAPDistTunnelMcastPacketsTransmitted Counter64
  wsManagedAPDistTunnelMcastPacketsReceived Counter64
  wsManagedAPDistTunnelRoamedClients Unsigned32
  wsManagedAPDistTunnelRoamedClientsIdleTimedOut Unsigned32
  wsManagedAPDistTunnelRoamedClientsAgeTimedOut Unsigned32
  wsManagedAPDistTunnelMaxClientLimitSetupDenials Unsigned32
  wsManagedAPDistTunnelMaxReplSetupDenials Unsigned32
  wsManagedAPARPReqsFromBcastToUcast Unsigned32
  wsManagedAPFilteredARPRequest Unsigned32
  wsManagedAPBroadcastedARPRequests Unsigned32

WsManagedAPRadioStatusEntry  
SEQUENCE    
  wsManagedAPRadioInterface Integer32
  wsManagedAPRadioMacAddress MacAddress
  wsManagedAPRadioChannel Integer32
  wsManagedAPRadioTxPower Integer32
  wsManagedAPRadioAuthenticatedClients Unsigned32
  wsManagedAPRadioWLANUtilization Integer32
  wsManagedAPRadioFixedChannelIndicator INTEGER
  wsManagedAPRadioMCAStatus INTEGER
  wsManagedAPRadioFixedPowerIndicator INTEGER
  wsManagedAPRadioMPAStatus INTEGER
  wsManagedAPRadioNeighborCount Unsigned32
  wsManagedAPRadioFixedChannelAction INTEGER
  wsManagedAPRadioFixedChannel Integer32
  wsManagedAPRadioFixedPowerAction INTEGER
  wsManagedAPRadioFixedPower Integer32
  wsManagedAPRadioBandwidth INTEGER
  wsManagedAPRadioResourceMeasEnabled INTEGER

WsManagedAPRadioStatisticsEntry  
SEQUENCE    
  wsManagedAPRadioWLANPktsRecvd Counter64
  wsManagedAPRadioWLANBytesRecvd Counter64
  wsManagedAPRadioWLANPktsTransmitted Counter64
  wsManagedAPRadioWLANBytesTransmitted Counter64
  wsManagedAPRadioTxFragmentCount Counter32
  wsManagedAPRadioMcastTxFrameCount Counter32
  wsManagedAPRadioFailedCount Counter32
  wsManagedAPRadioRetryCount Counter32
  wsManagedAPRadioMultipleRetryCount Counter32
  wsManagedAPRadioFrameDuplicateCount Counter32
  wsManagedAPRadioRTSSuccessCount Counter32
  wsManagedAPRadioRTSFailureCount Counter32
  wsManagedAPRadioACKFailureCount Counter32
  wsManagedAPRadioRecvdFragmentCount Counter32
  wsManagedAPRadioMcastRecvdFrameCount Counter32
  wsManagedAPRadioFCSErrorCount Counter32
  wsManagedAPRadioTxFrameCount Counter32
  wsManagedAPRadioWEPUndecryptableCount Counter32
  wsManagedAPRadioWLANPktsRecvDropped Counter64
  wsManagedAPRadioWLANBytesRecvDropped Counter64
  wsManagedAPRadioWLANPktsTransmitDropped Counter64
  wsManagedAPRadioWLANBytesTransmitDropped Counter64

WsManagedAPNeighborAPListEntry  
SEQUENCE    
  wsNeighborMacAddress MacAddress
  wsNeighborSSID DisplayString
  wsNeighborRSSI Integer32
  wsNeighborStatus INTEGER
  wsNeighborAge TimeTicks

WsManagedAPNeighborClientListEntry  
SEQUENCE    
  wsNeighborClientMacAddress MacAddress
  wsNeighborClientRSSI Integer32
  wsNeighborClientChannel Integer32
  wsNeighborClientAge TimeTicks
  wsNeighborClientDiscoveryReason BITS

WsManagedAPVAPStatusEntry  
SEQUENCE    
  wsManagedVAPId Integer32
  wsManagedVAPMacAddress MacAddress
  wsManagedVAPSSID DisplayString
  wsManagedVAPAuthenticatedClients Unsigned32

WsManagedAPVAPStatisticsEntry  
SEQUENCE    
  wsManagedVAPAssociationFailures Counter32
  wsManagedVAPAuthenticationFailures Counter32
  wsManagedVAPWLANPktsRecvd Counter64
  wsManagedVAPWLANBytesRecvd Counter64
  wsManagedVAPWLANPktsTransmitted Counter64
  wsManagedVAPWLANBytesTransmitted Counter64
  wsManagedVAPWLANPktsRecvDropped Counter64
  wsManagedVAPWLANBytesRecvDropped Counter64
  wsManagedVAPWLANPktsTransmitDropped Counter64
  wsManagedVAPWLANBytesTransmitDropped Counter64

WsManagedAPRadioEligibleChannelListEntry  
SEQUENCE    
  wsManagedAPRadioEligibleChannel Integer32
  wsManagedAPRadioEligibleChannelRdrDetRequired INTEGER
  wsManagedAPRadioEligibleChannelRdrDetected INTEGER
  wsManagedAPRadioEligibleChannelLastRdrDetTime DisplayString

WsAssociatedClientStatusEntry  
SEQUENCE    
  wsAssociatedClientMacAddress MacAddress
  wsAssociatedClientTunnelIpAddress IpAddress
  wsAssociatedClientUserName DisplayString
  wsAssociatedClientSSID DisplayString
  wsAssociatedClientVLAN Integer32
  wsAssociatedClientStatus INTEGER
  wsAssociatedClientTxDataRate Integer32
  wsAssociatedClientInactivePeriod TimeTicks
  wsAssociatedClientDisassociateAction INTEGER
  wsAssociatedClientAge TimeTicks
  wsAssociatedClientNwTime TimeTicks
  wsAssociatedClientAssociatingSwitch INTEGER
  wsAssociatedClientSwitchMacAddress MacAddress
  wsAssociatedClientSwitchIpAddress IpAddress
  wsAssociatedClientDot11nCapable INTEGER
  wsAssociatedClientStbcCapable INTEGER
  wsAssociatedClientDistTunnelStatus INTEGER
  wsAssociatedClientDistTunnelRoamStatus INTEGER
  wsAssociatedClientDistTunnelHomeAPMac MacAddress
  wsAssociatedClientDistTunnelAssocAPMac MacAddress
  wsAssociatedClientAPMacAddress MacAddress
  wsAssociatedClientBSSID MacAddress
  wsAssociatedClientRadioInterface Integer32
  wsAssociatedClientChannel Integer32
  wsAssociatedClientIpAddress IpAddress
  wsAssociatedClientNetBiosName DisplayString
  wsAssociatedClientRRMSupported INTEGER
  wsAssociatedClientRRMLocationReportSupported INTEGER
  wsAssociatedClientRRMBeaconTableMeasurementSupported INTEGER
  wsAssociatedClientRRMBeaconActiveMeasurementSupported INTEGER
  wsAssociatedClientRRMBeaconPassiveMeasurementSupported INTEGER
  wsAssociatedClientRRMChannelLoadMeasurementSupported INTEGER

WsAssociatedClientStatisticsEntry  
SEQUENCE    
  wsAssociatedClientPktsRecvd Counter64
  wsAssociatedClientBytesRecvd Counter64
  wsAssociatedClientPktsTransmitted Counter64
  wsAssociatedClientBytesTransmitted Counter64
  wsAssociatedClientDuplicatePktsRecvd Counter32
  wsAssociatedClientFragmentedPktsRecvd Counter32
  wsAssociatedClientFragmentedPktsTransmitted Counter32
  wsAssociatedClientTransmitRetryCount Counter32
  wsAssociatedClientTransmitRetryFailedCount Counter32
  wsAssociatedClientPktsRecvDropped Counter64
  wsAssociatedClientBytesRecvDropped Counter64
  wsAssociatedClientPktsTransmitDropped Counter64
  wsAssociatedClientBytesTransmitDropped Counter64
  wsAssociatedClientTsViolatePktsRecvd Counter32
  wsAssociatedClientTsViolatePktsTransmitted Counter32

WsAssociatedClientNeighborManagedAPStatusEntry  
SEQUENCE    
  wsClientStationMacAddress MacAddress
  wsClientNeighborWSManagedAPMacAddress MacAddress
  wsClientNeighborWSManagedAPRadioInterface Integer32
  wsClientStationDiscoveryReason BITS

WsVAPAssociatedClientStatusEntry  
SEQUENCE    
  wsVAPMacAddress MacAddress
  wsVAPAssociatedClientMacAddress MacAddress

WsSSIDAssociatedClientStatusEntry  
SEQUENCE    
  wsSSID DisplayString
  wsSSIDAssociatedClientMacAddress MacAddress

WsSwitchAssociatedClientStatusEntry  
SEQUENCE    
  wsAssociatedClientSwitchIPAddress IpAddress
  wsSwitchAssociatedClientMacAddress MacAddress

WsAssociatedClientQosStatusEntry  
SEQUENCE    
  wsAssociatedClientQosBandwidthLimitDown Unsigned32
  wsAssociatedClientQosBandwidthLimitUp Unsigned32
  wsAssociatedClientQosAccessControlDownType INTEGER
  wsAssociatedClientQosAccessControlDownName DisplayString
  wsAssociatedClientQosAccessControlUpType INTEGER
  wsAssociatedClientQosAccessControlUpName DisplayString
  wsAssociatedClientQosDiffservPolicyDownType INTEGER
  wsAssociatedClientQosDiffservPolicyDownName DisplayString
  wsAssociatedClientQosDiffservPolicyUpType INTEGER
  wsAssociatedClientQosDiffservPolicyUpName DisplayString
  wsAssociatedClientQosOperStatus INTEGER

WsAssociatedClientSessionStatisticsEntry  
SEQUENCE    
  wsAssociatedClientSessionPktsRecvd Counter64
  wsAssociatedClientSessionBytesRecvd Counter64
  wsAssociatedClientSessionPktsTransmitted Counter64
  wsAssociatedClientSessionBytesTransmitted Counter64
  wsAssociatedClientSessionDuplicatePktsRecvd Counter32
  wsAssociatedClientSessionFragmentedPktsRecvd Counter32
  wsAssociatedClientSessionFragmentedPktsTransmitted Counter32
  wsAssociatedClientSessionTransmitRetryCount Counter32
  wsAssociatedClientSessionTransmitRetryFailedCount Counter32
  wsAssociatedClientSessionPktsRecvDropped Counter64
  wsAssociatedClientSessionBytesRecvDropped Counter64
  wsAssociatedClientSessionPktsTransmitDropped Counter64
  wsAssociatedClientSessionBytesTransmitDropped Counter64
  wsAssociatedClientSessionTSViolatePktsRecvd Counter32
  wsAssociatedClientSessionTSViolatePktsTransmitted Counter32

WsAssociatedClientQosCachedStatusEntry  
SEQUENCE    
  wsAssociatedClientQosCachedBandwidthLimitDown Unsigned32
  wsAssociatedClientQosCachedBandwidthLimitUp Unsigned32
  wsAssociatedClientQosCachedAccessControlDownType INTEGER
  wsAssociatedClientQosCachedAccessControlDownName DisplayString
  wsAssociatedClientQosCachedAccessControlUpType INTEGER
  wsAssociatedClientQosCachedAccessControlUpName DisplayString
  wsAssociatedClientQosCachedDiffservPolicyDownType INTEGER
  wsAssociatedClientQosCachedDiffservPolicyDownName DisplayString
  wsAssociatedClientQosCachedDiffservPolicyUpType INTEGER
  wsAssociatedClientQosCachedDiffservPolicyUpName DisplayString

WsPeerStatusEntry  
SEQUENCE    
  wsPeerIpAddress IpAddress
  wsPeerClusterControllerIndicator INTEGER
  wsPeerTotalPeerSwitches Integer32
  wsPeerVendorId Integer32
  wsPeerProtocolVersion Integer32
  wsPeerSoftwareVersion DisplayString
  wsPeerDiscoveryReason INTEGER
  wsPeerAge TimeTicks
  wsPeerManagedAPCount INTEGER
  wsPeerConfigRequestAction INTEGER
  wsPeerConfigRequestStatus INTEGER
  wsPeerConfigSwitchIp IpAddress
  wsPeerConfigReceived BITS
  wsPeerConfigReceivedTimestamp DisplayString

WsPeerSwitchManagedAPEntry  
SEQUENCE    
  wsPeerSwitchIpAddress IpAddress
  wsPeerSwitchAPMacAddress MacAddress
  wsPeerSwitchAPLocation DisplayString
  wsPeerSwitchAPIPAddress IpAddress
  wsPeerSwitchAPProfileId INTEGER
  wsPeerSwitchAPProfileName DisplayString
  wsPeerSwitchAPHardwareType Integer32

WsRFScanAPStatusEntry  
SEQUENCE    
  wsRFScanAPMacAddress MacAddress
  wsRFScanAPRadioInterface Integer32
  wsRFScanAPBaseMacAddress MacAddress
  wsRFScanAPSSID DisplayString
  wsRFScanAPPhysicalMode INTEGER
  wsRFScanAPChannel Integer32
  wsRFScanAPTxRate DisplayString
  wsRFScanAPBeaconInterval Integer32
  wsRFScanAPStatus INTEGER
  wsRFScanAPDiscoveredAge TimeTicks
  wsRFScanAPAge TimeTicks
  wsRFScanAPStatusInitial INTEGER
  wsRFScanAPSecurityMode INTEGER
  wsRFScanAPHighRate DisplayString
  wsRFScanAPDot11nMode INTEGER
  wsRFScanAPAdHoc INTEGER
  wsRFScanAPPeerManaged INTEGER
  wsRFScanAPRogueMitigation INTEGER
  wsRFScanAPAcknowledgeRogue INTEGER
  wsRFScanAPBSSID MacAddress
  wsRFScanAPOUI DisplayString
  wsRFScanAPRRMSupported INTEGER
  wsRFScanAPDot11acMode INTEGER

WsFailureAPStatusEntry  
SEQUENCE    
  wsFailedAPMacAddress MacAddress
  wsFailedAPIpAddress IpAddress
  wsFailedAPVendorId INTEGER
  wsFailedAPSoftwareVersion DisplayString
  wsFailedAPHWType INTEGER
  wsFailedAPFailureType INTEGER
  wsFailedAPValidationFailureCount Unsigned32
  wsFailedAPAuthenticationFailureCount Unsigned32
  wsFailedAPProtocolVersion Integer32
  wsFailedAPAge TimeTicks
  wsFailedAPReportingSwitch INTEGER
  wsFailedAPSwitchMacAddress MacAddress
  wsFailedAPSwitchIpAddress IpAddress

WsAdHocClientStatusEntry  
SEQUENCE    
  wsAdHocClientMacAddress MacAddress
  wsDetectedAPMacAddress MacAddress
  wsDetectedAPRadioInterface Integer32
  wsAdHocClientDetectionMode INTEGER
  wsAdHocClientAge TimeTicks

WsAPTriangulationNonSentryStatusEntry  
SEQUENCE    
  wsAPTriangulationMacAddr MacAddress
  wsAPTriangulationId Integer32
  wsAPTriangulationNonSentryMacAddr MacAddress
  wsAPTriangulationNonSentryRadio Integer32
  wsAPTriangulationRssi Integer32
  wsAPTriangulationStrength Integer32
  wsAPTriangulationNoise Integer32
  wsAPTriangulationAge TimeTicks

WsAPTriangulationSentryStatusEntry  
SEQUENCE    
  wsAPSentryTriangulationMacAddr MacAddress
  wsAPSentryTriangulationId Integer32
  wsAPSentryTriangulationSentryMacAddr MacAddress
  wsAPSentryTriangulationSentryRadio Integer32
  wsAPSentryTriangulationRssi Integer32
  wsAPSentryTriangulationStrength Integer32
  wsAPSentryTriangulationNoise Integer32
  wsAPSentryTriangulationAge TimeTicks

WsAPRogueClassificationStatusEntry  
SEQUENCE    
  wsAPRogueClassificationMacAddr MacAddress
  wsAPRogueClassificationTestId Integer32
  wsAPRogueClassificationTestName INTEGER
  wsAPRogueClassificationDetected INTEGER
  wsAPRogueClassificationReportingAPMac MacAddress
  wsAPRogueClassificationReportingAPRadio Integer32
  wsAPRogueClassificationTestState INTEGER
  wsAPRogueClassificationTestResult INTEGER
  wsAPRogueClassificationFirstTime TimeTicks
  wsAPRogueClassificationLastTime TimeTicks

WsAPDeAuthenticationAttackStatusEntry  
SEQUENCE    
  wsAPDeAuthenticationAttackStatusId Integer32
  wsAPDeAuthenticationAttackBSSID MacAddress
  wsAPDeAuthenticationAttackChannel Integer32
  wsAPDeAuthenticationAttackTime TimeTicks
  wsAPDeAuthenticationAttackAge TimeTicks

WsDetectedClientStatusEntry  
SEQUENCE    
  wsDetectedClientMacAddress MacAddress
  wsDetectedClientStatus INTEGER
  wsDetectedClientAuthStatus INTEGER
  wsDetectedClientEntryLastUpdatedAt TimeTicks
  wsDetectedClientThreatDetectedStatus INTEGER
  wsDetectedClientThreatMitigationStatus INTEGER
  wsDetectedClientName DisplayString
  wsDetectedClientEntryCreateTime TimeTicks
  wsDetectedClientChannel Unsigned32
  wsDetectedClientAuthRSSI Unsigned32
  wsDetectedClientAuthSignal Integer32
  wsDetectedClientAuthNoise Integer32
  wsDetectedClientProbeReqRecorded Unsigned32
  wsDetectedClientProbeCollectionIntvl TimeTicks
  wsDetectedClientHighestNumProbes Unsigned32
  wsDetectedClientAuthMsgsRecorded Unsigned32
  wsDetectedClientAuthCollectionIntvl TimeTicks
  wsDetectedClientHighestNumAuthMsgs Unsigned32
  wsDetectedClientDeAuthMsgsRecorded Unsigned32
  wsDetectedClientDeAuthCollectionIntvl TimeTicks
  wsDetectedClientHighestNumDeAuthMsgs Unsigned32
  wsDetectedClientAuthFailures Unsigned32
  wsDetectedClientProbesDetected Unsigned32
  wsDetectedClientBcastBSSIDProbes Unsigned32
  wsDetectedClientBcastSSIDProbes Unsigned32
  wsDetectedClientSpecificBSSIDProbes Unsigned32
  wsDetectedClientSpecificSSIDProbes Unsigned32
  wsDetectedClientLastNonBcastBSSID MacAddress
  wsDetectedClientLastNonBcastSSID DisplayString
  wsDetectedClientThreatMitigationSent TimeTicks
  wsDetectedClientEntryPurge INTEGER
  wsDetectedClientEntryAcknowledge INTEGER
  wsDetectedClientOUI DisplayString

WsClientRogueClassificationStatusEntry  
SEQUENCE    
  wsClientRogueClassificationMacAddr MacAddress
  wsClientRogueClassificationTestId Integer32
  wsClientRogueClassificationTestName INTEGER
  wsClientRogueClassificationDetected INTEGER
  wsClientRogueClassificationReportingAPMac MacAddress
  wsClientRogueClassificationReportingAPRadio Integer32
  wsClientRogueClassificationTestState INTEGER
  wsClientRogueClassificationTestResult INTEGER
  wsClientRogueClassificationFirstTime TimeTicks
  wsClientRogueClassificationLastTime TimeTicks

WsDetectedClientTriangulationNonSentryStatusEntry  
SEQUENCE    
  wsDetectedClientTriangulationMacAddr MacAddress
  wsDetectedClientTriangulationId Integer32
  wsDetectedClientTriangulationNonSentryMacAddr MacAddress
  wsDetectedClientTriangulationNonSentryRadio Integer32
  wsDetectedClientTriangulationRssi Integer32
  wsDetectedClientTriangulationStrength Integer32
  wsDetectedClientTriangulationNoise Integer32
  wsDetectedClientTriangulationAge TimeTicks

WsDetectedClientTriangulationSentryStatusEntry  
SEQUENCE    
  wsDetectedClientSentryTriangulationMacAddr MacAddress
  wsDetectedClientSentryTriangulationId Integer32
  wsDetectedClientSentryTriangulationSentryMacAddr MacAddress
  wsDetectedClientSentryTriangulationSentryRadio Integer32
  wsDetectedClientSentryTriangulationRssi Integer32
  wsDetectedClientSentryTriangulationStrength Integer32
  wsDetectedClientSentryTriangulationNoise Integer32
  wsDetectedClientSentryTriangulationAge TimeTicks

WsDetectedClientPreAuthenticationHistoryEntry  
SEQUENCE    
  wsDetectedClientPreAuthenticationMacAddr MacAddress
  wsDetectedClientPreAuthenticationId Unsigned32
  wsDetectedClientPreAuthenticationApMac MacAddress
  wsDetectedClientPreAuthenticationApRadioId Integer32
  wsDetectedClientPreAuthenticationVapMac MacAddress
  wsDetectedClientPreAuthenticationSSID DisplayString
  wsDetectedClientPreAuthenticationAge TimeTicks
  wsDetectedClientPreAuthenticationStatus INTEGER

WsDetectedClientRoamHistoryEntry  
SEQUENCE    
  wsDetectedClientRoamMacAddr MacAddress
  wsDetectedClientRoamId Unsigned32
  wsDetectedClientRoamApMac MacAddress
  wsDetectedClientRoamApRadioId Integer32
  wsDetectedClientRoamVapMac MacAddress
  wsDetectedClientRoamSSID DisplayString
  wsDetectedClientRoamAge TimeTicks
  wsDetectedClientRoamStatus INTEGER

WsRrmNeighborEntry  
SEQUENCE    
  wsRrmNeighborApMacAddr MacAddress
  wsRrmNeighborVapMacAddr MacAddress
  wsRrmNeighborMacAddr MacAddress
  wsRrmNeighborRSSI Integer32
  wsRrmNeighborSSID DisplayString
  wsRrmNeighborChannel Integer32
  wsRrmNeighborAge TimeTicks
  wsRrmNeighborAllPurge INTEGER
  wsRrmNeighborApPurge INTEGER
  wsRrmNeighborVapPurge INTEGER

WsRrmChannelLoadHistoryEntry  
SEQUENCE    
  wsRrmChannelLoadHistoryEntryId Unsigned32
  wsRrmChannelLoadHistoryEntryApMacAddr MacAddress
  wsRrmChannelLoadHistoryEntryClientMacAddr MacAddress
  wsRrmChannelLoadHistoryEntryChannel Unsigned32
  wsRrmChannelLoadHistoryEntryDuration Unsigned32
  wsRrmChannelLoadHistoryEntryAge TimeTicks
  wsRrmChannelLoadHistoryEntryLoad Unsigned32

WsAPHardwareCapabilityEntry  
SEQUENCE    
  wsAPHWTypeID Integer32
  wsAPHWTypeDescription DisplayString
  wsAPHWTypeRadioCount Integer32
  wsAPImageTypeID Integer32
  wsAPHWDualBootSuppport INTEGER

WsAPHardwareRadioCapabilityEntry  
SEQUENCE    
  wsAPHWTypeRadioNum Integer32
  wsAPHWTypeRadioID Integer32
  wsAPHWTypeRadioDescription DisplayString
  wsAPHWTypeRadioVapCount Integer32
  wsAPHWTypeRadioAmodeSupport INTEGER
  wsAPHWTypeRadioBGmodeSupport INTEGER
  wsAPHWTypeRadioNmodeSupport INTEGER
  wsAPHWTypeRadioACmodeSupport INTEGER

WsAPImageTypeCapabilityEntry  
SEQUENCE    
  wsAPImageTypeDescription DisplayString

WsAPImageAvailabilityEntry  
SEQUENCE    
  wsAPImageAvailability DisplayString

WsGlobalTspecStatisticsEntry  
SEQUENCE    
  wsTspecACIndex TspecSuppAC
  wsTotalWLANTspecPktsRecvd Counter64
  wsTotalWLANTspecPktsTransmitted Counter64
  wsTotalWLANTspecBytesRecvd Counter64
  wsTotalWLANTspecBytesTransmitted Counter64
  wsTotalWLANTspecsAccepted Counter32
  wsTotalWLANTspecsRejected Counter32
  wsTotalWLANRoamingTspecsAccepted Counter32
  wsTotalWLANRoamingTspecsRejected Counter32

WsSwitchTspecStatusEntry  
SEQUENCE    
  wsSwitchTspecTotalVoiceTrafficStreams Unsigned32
  wsSwitchTspecTotalVideoTrafficStreams Unsigned32
  wsSwitchTspecTotalTrafficStreamClients Unsigned32
  wsSwitchTspecTotalTrafficStreamRoamingClients Unsigned32

WsSwitchTspecStatisticsEntry  
SEQUENCE    
  wsSwitchWLANTspecPktsRecvd Counter64
  wsSwitchWLANTspecPktsTransmitted Counter64
  wsSwitchWLANTspecBytesRecvd Counter64
  wsSwitchWLANTspecBytesTransmitted Counter64
  wsSwitchWLANTspecsAccepted Counter32
  wsSwitchWLANTspecsRejected Counter32
  wsSwitchWLANRoamingTspecsAccepted Counter32
  wsSwitchWLANRoamingTspecsRejected Counter32

WsManagedAPTspecStatusEntry  
SEQUENCE    
  wsManagedAPTspecNumActiveTrafficStreams Unsigned32
  wsManagedAPTspecNumTrafficStreamClients Unsigned32
  wsManagedAPTspecNumTrafficStreamRoamingClients Unsigned32

WsManagedAPTspecStatisticsEntry  
SEQUENCE    
  wsManagedAPTspecPktsRecvd Counter64
  wsManagedAPTspecPktsTransmitted Counter64
  wsManagedAPTspecBytesRecvd Counter64
  wsManagedAPTspecBytesTransmitted Counter64
  wsManagedAPTspecsAccepted Counter32
  wsManagedAPTspecsRejected Counter32
  wsManagedAPRoamingTspecsAccepted Counter32
  wsManagedAPRoamingTspecsRejected Counter32

WsManagedAPRadioTspecStatusEntry  
SEQUENCE    
  wsManagedAPRadioTspecOperStatus INTEGER
  wsManagedAPRadioTspecNumActiveTrafficStreams Unsigned32
  wsManagedAPRadioTspecNumTrafficStreamClients Unsigned32
  wsManagedAPRadioTspecNumTrafficStreamRoamingClients Unsigned32
  wsManagedAPRadioTspecMediumTimeAdmitted Unsigned32
  wsManagedAPRadioTspecMediumTimeUnallocated Unsigned32
  wsManagedAPRadioTspecMediumTimeRoamingUnallocated Unsigned32

WsManagedAPRadioTspecStatisticsEntry  
SEQUENCE    
  wsManagedAPRadioTspecPktsRecvd Counter64
  wsManagedAPRadioTspecPktsTransmitted Counter64
  wsManagedAPRadioTspecBytesRecvd Counter64
  wsManagedAPRadioTspecBytesTransmitted Counter64

WsManagedAPVAPTspecStatusEntry  
SEQUENCE    
  wsManagedAPVAPTspecOperStatus INTEGER
  wsManagedAPVAPTspecNumActiveTrafficStreams Unsigned32
  wsManagedAPVAPTspecNumTrafficStreamClients Unsigned32
  wsManagedAPVAPTspecNumTrafficStreamRoamingClients Unsigned32
  wsManagedAPVAPTspecMediumTimeAdmitted Unsigned32
  wsManagedAPVAPTspecMediumTimeUnallocated Unsigned32
  wsManagedAPVAPTspecMediumTimeRoamingUnallocated Unsigned32

WsManagedAPVAPTspecStatisticsEntry  
SEQUENCE    
  wsManagedAPVAPTspecPktsRecvd Counter64
  wsManagedAPVAPTspecPktsTransmitted Counter64
  wsManagedAPVAPTspecBytesRecvd Counter64
  wsManagedAPVAPTspecBytesTransmitted Counter64

WsAssociatedClientTsStatusEntry  
SEQUENCE    
  wsAssociatedClientTsTid Unsigned32
  wsAssociatedClientTsAccessCategory TspecSuppAC
  wsAssociatedClientTsDirection INTEGER
  wsAssociatedClientTsUserPriority Unsigned32
  wsAssociatedClientTsMediumTime Unsigned32
  wsAssociatedClientTsExcessUsageEvents Unsigned32
  wsAssociatedClientTsRoamingClientIndicator INTEGER

WsAssociatedClientTsStatisticsEntry  
SEQUENCE    
  wsAssociatedClientTsPktsRecvd Counter64
  wsAssociatedClientTsPktsTransmitted Counter64
  wsAssociatedClientTsBytesRecvd Counter64
  wsAssociatedClientTsBytesTransmitted Counter64

WsAPProvisioningEntry  
SEQUENCE    
  wsAPProvMacAddress MacAddress
  wsAPProvIPAddress IpAddress
  wsAPProvPrimarySwitchIP IpAddress
  wsAPProvBackupSwitchIP IpAddress
  wsAPProvMutualAuthMode INTEGER
  wsAPProvUnmanagedAPReprovMode INTEGER
  wsAPProvAge TimeTicks
  wsAPProvNewPrimarySwitchIP IpAddress
  wsAPProvNewBackupSwitchIP IpAddress
  wsAPProvNewProfileId Integer32
  wsAPProvCommand INTEGER
  wsAPProvStatus INTEGER
  wsAPProvCertProfileTxStatus INTEGER
  wsAPProvEntryPurge INTEGER

WsWDSAPGroupEntry  
SEQUENCE    
  wsWDSAPGroupId Integer32
  wsWDSAPGroupName DisplayString
  wsWDSAPGroupSpanningTree INTEGER
  wsWDSAPGroupPassword DisplayString
  wsWDSAPGroupRowStatus RowStatus

WsWDSAPGroupAPEntry  
SEQUENCE    
  wsWDSAPGroupAPMacAddress MacAddress
  wsWDSAPGroupAPStpPriority Integer32
  wsWDSAPGroupAPEntryRowStatus RowStatus

WsWDSAPLinkEntry  
SEQUENCE    
  wsWDSAPLinkSourceMacAddr MacAddress
  wsWDSAPLinkSourceRadio Integer32
  wsWDSAPLinkDestMacAddr MacAddress
  wsWDSAPLinkDestRadio Integer32
  wsWDSAPLinkPathCost Integer32
  wsWDSAPLinkRowStatus RowStatus

WsWDSAPGroupStatusEntry  
SEQUENCE    
  wsWDSConfigAPCount Integer32
  wsWDSConnectedAPCount Integer32
  wsWDSRootAPCount Integer32
  wsWDSSatelliteAPCount Integer32
  wsWDSAPRootBridge MacAddress
  wsWDSAPRootDeviceType INTEGER
  wsWDSConfigWDSLinkCount Integer32
  wsWDSDetectedWDSLinkCount Integer32
  wsWDSBlockedWDSLinkCount Integer32
  wsWDSGroupNewPassword DisplayString
  wsWDSGroupChangePasswdStart INTEGER
  wsWDSGroupChangePasswdStatus INTEGER

WsWDSAPStatusEntry  
SEQUENCE    
  wsWDSAPMacAddr MacAddress
  wsWDSAPConnectionStatus INTEGER
  wsWDSAPSatelliteMode INTEGER
  wsWDSAPSTPRootMode INTEGER
  wsWDSAPSTPCost Unsigned32
  wsWDSAPEthPortSTPStatus INTEGER
  wsWDSAPEthPortMode INTEGER
  wsWDSAPEthPortLinkState INTEGER

WsWDSLinkStatusEntry  
SEQUENCE    
  wsWDSSourceMacAddr MacAddress
  wsWDSSourceRadio Integer32
  wsWDSDestMacAddr MacAddress
  wsWDSDestRadio Integer32
  wsWDSLinkSourceEndPointDetected INTEGER
  wsWDSLinkDestEndPointDetected INTEGER
  wsWDSLinkSourceSTPState INTEGER
  wsWDSLinkDestSTPState INTEGER
  wsWDSLinkAggregationMode INTEGER

WsWDSLinkStatisticsEntry  
SEQUENCE    
  wsWDSLinkSourceAPPktsSent Counter64
  wsWDSLinkSourceAPBytesSent Counter64
  wsWDSLinkSourceAPPktsRcvd Counter64
  wsWDSLinkSourceAPBytesRcvd Counter64
  wsWDSLinkDestAPPktsSent Counter64
  wsWDSLinkDestAPBytesSent Counter64
  wsWDSLinkDestAPPktsRcvd Counter64
  wsWDSLinkDestAPBytesRcvd Counter64

WsDevLocBldngEntry  
SEQUENCE    
  wsDevLocBldngNum Integer32
  wsDevLocBldngDesc DisplayString
  wsDevLocFlrCount INTEGER
  wsDevLocApCount INTEGER
  wsDevLocBldngRowStatus RowStatus

WsDevLocBldngFlrEntry  
SEQUENCE    
  wsDevLocBldngFlrNum Integer32
  wsDevLocBldngFlrDesc DisplayString
  wsDevLocBldngFlrApCount INTEGER
  wsDevLocFlrRowStatus RowStatus

WsDevLocManagedApEntry  
SEQUENCE    
  wsDevLocManagedApMac MacAddress
  wsDevLocMeasurementUnit INTEGER
  wsDevLocManagedApXCoord Integer32
  wsDevLocManagedApYCoord Integer32
  wsDevLocManagedApRowStatus RowStatus

WsOnDemandTriggerFloorStatusEntry  
SEQUENCE    
  wsOnDemandTriggerFloorStatusBuildingNum Unsigned32
  wsOnDemandTriggerFloorStatusFloorNum Unsigned32
  wsOnDemandTriggerFloorStatusDeviceFound INTEGER
  wsOnDemandTriggerFloorStatusNumOfAPs Unsigned32
  wsOnDemandTriggerFloorStatusSolutionType INTEGER
  wsOnDemandTriggerFloorStatusXCoordinate INTEGER
  wsOnDemandTriggerFloorStatusYCoordinate INTEGER
  wsOnDemandTriggerFloorStatusCircleRadius Unsigned32
  wsOnDemandTriggerFloorStatusSigma INTEGER

WsTriangulationLocStatusEntry  
SEQUENCE    
  wsTriangLocMacAddress MacAddress
  wsTriangLocDataType INTEGER
  wsTriangLocStatus INTEGER
  wsTriangLocDeviceType INTEGER
  wsTriangLocAge TimeTicks
  wsTriangLocBldng Integer32
  wsTriangLocFlr Integer32
  wsTriangLocXCoord Integer32
  wsTriangLocYCoord Integer32

WsAuthenticatedClientStatusEntry  
SEQUENCE    
  wsAuthenticatedClientMacAddress MacAddress
  wsAuthenticatedClientTunnelIpAddress IpAddress
  wsAuthenticatedClientUserName DisplayString
  wsAuthenticatedClientSSID DisplayString
  wsAuthenticatedClientVLAN Integer32
  wsAuthenticatedClientStatus INTEGER
  wsAuthenticatedClientTxDataRate Integer32
  wsAuthenticatedClientInactivePeriod TimeTicks
  wsAuthenticatedClientDisassociateAction INTEGER
  wsAuthenticatedClientAge TimeTicks
  wsAuthenticatedClientNwTime TimeTicks
  wsAuthenticatedClientAssociatingSwitch INTEGER
  wsAuthenticatedClientSwitchMacAddress MacAddress
  wsAuthenticatedClientSwitchIpAddress IpAddress
  wsAuthenticatedClientDot11nCapable INTEGER
  wsAuthenticatedClientStbcCapable INTEGER
  wsAuthenticatedClientDistTunnelStatus INTEGER
  wsAuthenticatedClientDistTunnelRoamStatus INTEGER
  wsAuthenticatedClientDistTunnelHomeAPMac MacAddress
  wsAuthenticatedClientDistTunnelAssocAPMac MacAddress
  wsAuthenticatedClientAPMacAddress MacAddress
  wsAuthenticatedClientBSSID MacAddress
  wsAuthenticatedClientRadioInterface Integer32
  wsAuthenticatedClientChannel Integer32
  wsAuthenticatedClientIpAddress IpAddress
  wsAuthenticatedClientNetBiosName DisplayString
  wsAuthenticatedClientRRMSupported INTEGER
  wsAuthenticatedClientRRMLocationReportSupported INTEGER
  wsAuthenticatedClientRRMBeaconTableMeasurementSupported INTEGER
  wsAuthenticatedClientRRMBeaconActiveMeasurementSupported INTEGER
  wsAuthenticatedClientRRMBeaconPassiveMeasurementSupported INTEGER
  wsAuthenticatedClientRRMChannelLoadMeasurementSupported INTEGER
  wsAuthenticatedClientDot11acCapable INTEGER

WsAuthenticatedClientStatisticsEntry  
SEQUENCE    
  wsAuthenticatedClientPktsRecvd Counter64
  wsAuthenticatedClientBytesRecvd Counter64
  wsAuthenticatedClientPktsTransmitted Counter64
  wsAuthenticatedClientBytesTransmitted Counter64
  wsAuthenticatedClientDuplicatePktsRecvd Counter32
  wsAuthenticatedClientFragmentedPktsRecvd Counter32
  wsAuthenticatedClientFragmentedPktsTransmitted Counter32
  wsAuthenticatedClientTransmitRetryCount Counter32
  wsAuthenticatedClientTransmitRetryFailedCount Counter32
  wsAuthenticatedClientPktsRecvDropped Counter64
  wsAuthenticatedClientBytesRecvDropped Counter64
  wsAuthenticatedClientPktsTransmitDropped Counter64
  wsAuthenticatedClientBytesTransmitDropped Counter64
  wsAuthenticatedClientTsViolatePktsRecvd Counter32
  wsAuthenticatedClientTsViolatePktsTransmitted Counter32

WsAuthenticatedClientNeighborManagedAPStatusEntry  
SEQUENCE    
  wsAuthenticatedClientStationMacAddress MacAddress
  wsAuthenticatedClientNeighborWSManagedAPMacAddress MacAddress
  wsAuthenticatedClientNeighborWSManagedAPRadioInterface Integer32
  wsAuthenticatedClientStationDiscoveryReason BITS

WsVAPAuthenticatedClientStatusEntry  
SEQUENCE    
  wsAuthenticatedVAPMacAddress MacAddress
  wsVAPAuthenticatedClientMacAddress MacAddress

WsSSIDAuthenticatedClientStatusEntry  
SEQUENCE    
  wsAuthenticatedSSID DisplayString
  wsSSIDAuthenticatedClientMacAddress MacAddress

WsSwitchAuthenticatedClientStatusEntry  
SEQUENCE    
  wsAuthenticatedClientSwitchIPAddress IpAddress
  wsSwitchAuthenticatedClientMacAddress MacAddress

WsAuthenticatedClientQosStatusEntry  
SEQUENCE    
  wsAuthenticatedClientQosBandwidthLimitDown Unsigned32
  wsAuthenticatedClientQosBandwidthLimitUp Unsigned32
  wsAuthenticatedClientQosAccessControlDownType INTEGER
  wsAuthenticatedClientQosAccessControlDownName DisplayString
  wsAuthenticatedClientQosAccessControlUpType INTEGER
  wsAuthenticatedClientQosAccessControlUpName DisplayString
  wsAuthenticatedClientQosDiffservPolicyDownType INTEGER
  wsAuthenticatedClientQosDiffservPolicyDownName DisplayString
  wsAuthenticatedClientQosDiffservPolicyUpType INTEGER
  wsAuthenticatedClientQosDiffservPolicyUpName DisplayString
  wsAuthenticatedClientQosOperStatus INTEGER

WsAuthenticatedClientSessionStatisticsEntry  
SEQUENCE    
  wsAuthenticatedClientSessionPktsRecvd Counter64
  wsAuthenticatedClientSessionBytesRecvd Counter64
  wsAuthenticatedClientSessionPktsTransmitted Counter64
  wsAuthenticatedClientSessionBytesTransmitted Counter64
  wsAuthenticatedClientSessionDuplicatePktsRecvd Counter32
  wsAuthenticatedClientSessionFragmentedPktsRecvd Counter32
  wsAuthenticatedClientSessionFragmentedPktsTransmitted Counter32
  wsAuthenticatedClientSessionTransmitRetryCount Counter32
  wsAuthenticatedClientSessionTransmitRetryFailedCount Counter32
  wsAuthenticatedClientSessionPktsRecvDropped Counter64
  wsAuthenticatedClientSessionBytesRecvDropped Counter64
  wsAuthenticatedClientSessionPktsTransmitDropped Counter64
  wsAuthenticatedClientSessionBytesTransmitDropped Counter64
  wsAuthenticatedClientSessionTSViolatePktsRecvd Counter32
  wsAuthenticatedClientSessionTSViolatePktsTransmitted Counter32

WsAuthenticatedClientQosCachedStatusEntry  
SEQUENCE    
  wsAuthenticatedClientQosCachedBandwidthLimitDown Unsigned32
  wsAuthenticatedClientQosCachedBandwidthLimitUp Unsigned32
  wsAuthenticatedClientQosCachedAccessControlDownType INTEGER
  wsAuthenticatedClientQosCachedAccessControlDownName DisplayString
  wsAuthenticatedClientQosCachedAccessControlUpType INTEGER
  wsAuthenticatedClientQosCachedAccessControlUpName DisplayString
  wsAuthenticatedClientQosCachedDiffservPolicyDownType INTEGER
  wsAuthenticatedClientQosCachedDiffservPolicyDownName DisplayString
  wsAuthenticatedClientQosCachedDiffservPolicyUpType INTEGER
  wsAuthenticatedClientQosCachedDiffservPolicyUpName DisplayString

Defined Values

fastPathWLANSwitch 1.3.6.1.4.1.207.8.42.8.34
The Allied Telesis Private MIB for AT-UWC
MODULE-IDENTITY    

at-uwc 1.3.6.1.4.1.207.1.13.21
OBJECT IDENTIFIER    

wsTraps 1.3.6.1.4.1.207.8.42.8.34.0
OBJECT IDENTIFIER    

wsGlobalConfig 1.3.6.1.4.1.207.8.42.8.34.1
OBJECT IDENTIFIER    

discovery 1.3.6.1.4.1.207.8.42.8.34.2
OBJECT IDENTIFIER    

apProfile 1.3.6.1.4.1.207.8.42.8.34.3
OBJECT IDENTIFIER    

apCodeDownload 1.3.6.1.4.1.207.8.42.8.34.4
OBJECT IDENTIFIER    

rfManagement 1.3.6.1.4.1.207.8.42.8.34.5
OBJECT IDENTIFIER    

managedAP 1.3.6.1.4.1.207.8.42.8.34.6
OBJECT IDENTIFIER    

associatedClient 1.3.6.1.4.1.207.8.42.8.34.7
OBJECT IDENTIFIER    

peerSwitch 1.3.6.1.4.1.207.8.42.8.34.8
OBJECT IDENTIFIER    

intrusionDetection 1.3.6.1.4.1.207.8.42.8.34.9
OBJECT IDENTIFIER    

snmpTrapsConfig 1.3.6.1.4.1.207.8.42.8.34.10
OBJECT IDENTIFIER    

wsMibInfo 1.3.6.1.4.1.207.8.42.8.34.11
OBJECT IDENTIFIER    

wsCapability 1.3.6.1.4.1.207.8.42.8.34.12
OBJECT IDENTIFIER    

l2centTunnel 1.3.6.1.4.1.207.8.42.8.34.13
OBJECT IDENTIFIER    

wsOuiDatabase 1.3.6.1.4.1.207.8.42.8.34.14
OBJECT IDENTIFIER    

rrmNeighbor 1.3.6.1.4.1.207.8.42.8.34.15
OBJECT IDENTIFIER    

rrmChannelLoad 1.3.6.1.4.1.207.8.42.8.34.16
OBJECT IDENTIFIER    

tspec 1.3.6.1.4.1.207.8.42.8.34.17
OBJECT IDENTIFIER    

provisioning 1.3.6.1.4.1.207.8.42.8.34.18
OBJECT IDENTIFIER    

wdsManagedAP 1.3.6.1.4.1.207.8.42.8.34.19
OBJECT IDENTIFIER    

deviceLocation 1.3.6.1.4.1.207.8.42.8.34.20
OBJECT IDENTIFIER    

authenticatedClient 1.3.6.1.4.1.207.8.42.8.34.21
OBJECT IDENTIFIER    

wsMibVersion 1.3.6.1.4.1.207.8.42.8.34.11.1
The version number of this MIB module
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsMode 1.3.6.1.4.1.207.8.42.8.34.1.1
Flag to enable/disable wireless controller functionality on the device. Disable will purge all status and statistics related to wireless functionality.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsCountryCode 1.3.6.1.4.1.207.8.42.8.34.1.2
This object indicates country of operation for WLAN. Supported country codes are: Australia - AU, Austria - AT, Austria - AT, Belgium - BE, Brazil - BR, Canada - CA, China - CN, Czech Republic - CZ, Denmark - DK, Finland - FI, France - FR, Germany - DE, Greece - GR, Hong Kong - HK, Hungary - HU, Iceland - IS, India - IN, Ireland - IE, Israel - IL, Italy - IT, Japan - JP, Liechtenstein - LI,Luxembourg - LU,Malaysia - MY, Mexico - MX, Netherlands - NL, New Zealand - NZ, Norway - NO, Poland - PL, Portugal - PT, Saudi Arabia - SA, Singapore - SG, Slovakia - SK, Slovenia - SI, South Africa - ZA, South Korea - KR, Spain - ES, Sweden - SE, Switzerland - CH, Taiwan - TW, Thailand - TH, United Arab Emirates - AE, United Kingdom - GB, United States - US.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(2)  

wsPeerGroupId 1.3.6.1.4.1.207.8.42.8.34.1.3
This object indicates which peer group this controller belongs to, there may be more than one group of peer controllers in the WLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsAPValidationMethod 1.3.6.1.4.1.207.8.42.8.34.1.4
This object indicates whether or not to verify newly discovered APs and look up their configuration against the local database or a RADIUS server.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER local(1), radius(2)  

wsAPAuthenticationMode 1.3.6.1.4.1.207.8.42.8.34.1.5
Flag to indicate if authentication is required for an AP to establish communication with the controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsClientRoamAgeTime 1.3.6.1.4.1.207.8.42.8.34.1.6
Time in seconds to wait after a client disassociates from a managed AP before deleting the client association database entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..120  

wsRFScanAgeTime 1.3.6.1.4.1.207.8.42.8.34.1.7
Time in hours to wait before deleting an entry obtained from an RF scan.A value of 0 in input range means that the entry never ages out.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..168  

wsAPFailureAgeTime 1.3.6.1.4.1.207.8.42.8.34.1.8
Time in hours to wait before deleting an entry in the AP association and authentication failure list. A value of 0 in input range means that the entry never ages out.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..168  

wsAdHocClientAgeTime 1.3.6.1.4.1.207.8.42.8.34.1.9
Time in hours to wait before deleting an entry in Ad hoc client list.A value of 0 in input range means that the entry never ages out.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..168  

wsDetectedClientAgeTime 1.3.6.1.4.1.207.8.42.8.34.1.10
Time in hours to wait before deleting an entry from the detected clients database.A value of 0 in input range means that the entry never ages out.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..168  

wsValidAPConfigTable 1.3.6.1.4.1.207.8.42.8.34.1.11
This table contains configurable parameters for a specific AP. When an AP is discovered and the wsValidationMethod is local, its MAC address is verified in this table to determine if it should be managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsValidAPConfigEntry

wsValidAPConfigEntry 1.3.6.1.4.1.207.8.42.8.34.1.11.1
Each entry has parameters that can be configured locally or on a RADIUS server, for a specific AP on the WLAN. As this table is indexed by wsAPMacAddress, - to create an entry, specify the AP MAC address and set object wsAPConfigRowStatus to createAndGo(4) - to delete an entry, select the entry from the list and set object wsAPConfigRowStatus to destroy(6)
Status: current Access: not-accessible
OBJECT-TYPE    
  WsValidAPConfigEntry  

wsAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.1.11.1.1
MAC address of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPLocation 1.3.6.1.4.1.207.8.42.8.34.1.11.1.2
This object indicates description of an AP, often based on its location.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAPMode 1.3.6.1.4.1.207.8.42.8.34.1.11.1.3
This field indicates whether this AP is managed by the controller, by an administrator, or is a Rogue AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER wsManaged(1), standalone(2), rogue(3)  

wsAPAuthenticationPasswd 1.3.6.1.4.1.207.8.42.8.34.1.11.1.4
If AP authentication is enabled, this indicates the password for an AP to authenticate to the controller. This must match the password configured on an AP. When passwod is configured this object will always return '*****'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8..63)  

wsUseAPProfileId 1.3.6.1.4.1.207.8.42.8.34.1.11.1.5
If AP is managed by controller, this object indicates Id of configuration profile for this AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..16  

wsAPRadio1Channel 1.3.6.1.4.1.207.8.42.8.34.1.11.1.6
This object indicates the fixed channel for the AP radio one. Zero indicates automatic channel assignment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsAPRadio2Channel 1.3.6.1.4.1.207.8.42.8.34.1.11.1.7
This object indicates the fixed channel for the AP radio two. Zero indicates automatic channel assignment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsAPRadio1TxPower 1.3.6.1.4.1.207.8.42.8.34.1.11.1.8
This indicates the power setting of AP radio one. Zero indicates automatic power adjustment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsAPRadio2TxPower 1.3.6.1.4.1.207.8.42.8.34.1.11.1.9
This indicates the power setting of AP radio two. Zero indicates automatic power adjustment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsAPStandaloneExpectedChannel 1.3.6.1.4.1.207.8.42.8.34.1.11.1.10
This object indicates the expected channel for the AP in standalone mode. Zero indicates that any channel is allowed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsAPStandaloneExpectedSecurity 1.3.6.1.4.1.207.8.42.8.34.1.11.1.11
This object indicates the expected security mode for the AP in standalone mode. Zero indicates that any security mode is allowed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER any(0), open(1), wep(2), wpa(3)  

wsAPStandaloneExpectedSsid 1.3.6.1.4.1.207.8.42.8.34.1.11.1.12
This object indicates the expected SSID for the AP in standalone mode. A null string indicates that any SSID is allowed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAPStandaloneExpectedWds 1.3.6.1.4.1.207.8.42.8.34.1.11.1.13
This object indicates whether the AP is allowed to operate as a bridge. Configurable values are: any Either WDS or normal mode is allowed normal - AP is not allowed to operate in WDS mode bridge - AP is only allowed to operate in WDS mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER any(0), normal(1), bridge(2)  

wsAPStandaloneExpectedWired 1.3.6.1.4.1.207.8.42.8.34.1.11.1.14
This object indicates the expected wired network mode for the AP in standalone mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER allowed(0), not-allowed(1)  

wsAPConfigRowStatus 1.3.6.1.4.1.207.8.42.8.34.1.11.1.15
This object is used to create or delete entries in the table. The supported values are: active(1) - indicates a valid entry createAndGo(4) - creates a new entry in the table destroy(6) - removes an existing entry from the table As this table is indexed by wsAPMacAddress, - to create an entry, specify the AP MAC address and set object value to createAndGo(4) - to delete an entry, select the entry from the list and set object value to destroy(6)
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsGlobalStatus 1.3.6.1.4.1.207.8.42.8.34.1.12
OBJECT IDENTIFIER    

wsIPAddress 1.3.6.1.4.1.207.8.42.8.34.1.12.1
This object represents wireless controller IP address. When wireless mode is in disabled state, the value of controller IP address is zero.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsOperationalStatus 1.3.6.1.4.1.207.8.42.8.34.1.12.2
Indicates the current operating status of the wireless system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), enable-pending(2), disabled(3), disable-pending(4)  

wsOperationalStatusDisableReason 1.3.6.1.4.1.207.8.42.8.34.1.12.3
This object indicates the reason of operational status to be disabled. Values 5 and 6 are applicable only if routing functionality present.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), admin-disabled(2), no-ipAddress(3), no-sslFiles(4), no-loopback-interface(5), routing-disabled(6), no-active-interface(7)  

wsTotalPeerSwitches 1.3.6.1.4.1.207.8.42.8.34.1.12.4
Total number of peer controllers detected on the network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

wsTotalAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.5
Sum of all the WS managed APs, connection failed APs, and discovered APs in the database.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalManagedAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.6
Total number of WS managed APs currently authenticated to the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

wsTotalStandaloneAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.7
Total number of trusted AP's in the standalone mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalDiscoveredAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.8
Number of APs that are connected to the controller, but are not completely configured.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalConnectionFailedAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.9
Number of APs that were previously authenticated and managed, but currently do not have connection with the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalRogueAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.10
Total number of Rogue APs detected on the WLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalUnknownAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.11
Total number of Unknown APs detected on the WLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsMaximumManagedAPsInPeerGroup 1.3.6.1.4.1.207.8.42.8.34.1.12.12
Maximum number of APs that can be managed by the wireless controller when it acts as Cluster Controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalClients 1.3.6.1.4.1.207.8.42.8.34.1.12.13
Total number of clients present in the network.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalAuthenticatedClients 1.3.6.1.4.1.207.8.42.8.34.1.12.14
Total number of authenticated clients across all APs managed by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsMaximumAssociatedClients 1.3.6.1.4.1.207.8.42.8.34.1.12.15
Maximum number of clients that can associate with the wireless system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsWLANUtilization 1.3.6.1.4.1.207.8.42.8.34.1.12.16
Total network utilization across all APs managed by this controller. This is based on global statistics.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsGlobalStatusRegulatoryDomainFor2GHz 1.3.6.1.4.1.207.8.42.8.34.1.12.18
Regulatory domain for 2GHz frequency channels.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8..32)  

wsGlobalStatusRegulatoryDomainFor5GHz 1.3.6.1.4.1.207.8.42.8.34.1.12.19
Regulatory domain for 5GHz frequency channels.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8..32)  

wsGlobalPeerConfigRequestAction 1.3.6.1.4.1.207.8.42.8.34.1.12.20
This action object is used to: - start - Start the config push into all the peer controllers in the peer group. - Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsGlobalPeerConfigRequestStatus 1.3.6.1.4.1.207.8.42.8.34.1.12.21
The global status for the configuration push operation to one or more peer controllers.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(0), requested(1), savingConfig(2), sendingConfig(3), applyingAPprofileConfig(4), complete(5)  

wsGlobalPeerConfigReceiveStatus 1.3.6.1.4.1.207.8.42.8.34.1.12.22
The global status when wireless configuration is received from a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(0), receivingConfig(1), savingConfig(2), applyingAPprofileConfig(3), failureInvalidCodeVersion(4), failureInvalidHwVersion(5), failureInvalidConfig(6), failureInvalidPacketFormat(7), failureTimeout(8), success(9)  

wsGlobalPeerConfigSwitchIp 1.3.6.1.4.1.207.8.42.8.34.1.12.23
IP Address of the last controller from which this controller received any wireless configuration data.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsGlobalPeerConfigReceived 1.3.6.1.4.1.207.8.42.8.34.1.12.24
Indicates which portions of configuration were last received from a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  BITS none(1), globalConfig(2), discoveryConfig(3), validAPDatabase(4), channelPowerConfig(5), profileNetworkConfig(6), knownClientConfig(7), captivePortalConfig(8), radiusClientConfig(9), qosAclConfig(10), qosDiffServConfig(11), wdsGroupConfig(12), deviceLocationConfig(13)  

wsGlobalPeerConfigReceivedTimestamp 1.3.6.1.4.1.207.8.42.8.34.1.12.25
The last time this controller received any configuration data from a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsClusterControllerIndicator 1.3.6.1.4.1.207.8.42.8.34.1.12.26
Indicates if the controller is currently the Cluster Controller of the peer group or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsClusterController 1.3.6.1.4.1.207.8.42.8.34.1.12.27
This object represents Cluster Controller's IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsRogueAPMitigationCount 1.3.6.1.4.1.207.8.42.8.34.1.12.28
Number of APs to which the wireless system is currently sending de-authentication messages to mitigate against rogue APs.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsRogueAPMitigationLimit 1.3.6.1.4.1.207.8.42.8.34.1.12.29
Maximum number of APs for which the system can send de-authentication frames.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsRogueAPAcknowledgeAll 1.3.6.1.4.1.207.8.42.8.34.1.12.30
This is a command that allows the administrator to clear out all rogue AP states in the RF Scan database
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no-action(0), acknowledge(1)  

wsTotalDetectedClients 1.3.6.1.4.1.207.8.42.8.34.1.12.31
Total number of detected clients across all APs managed by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsMaximumDetectedClients 1.3.6.1.4.1.207.8.42.8.34.1.12.32
Maximum number of clients that can be maintained by the detected clients database.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsMaximumDetectedClientPreAuthenticationHistoryEntries 1.3.6.1.4.1.207.8.42.8.34.1.12.33
Maximum number of pre-authentication history entries that can be recorded for all the detected clients present in the detected client database.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalDetectedClientPreAuthenticationHistoryEntries 1.3.6.1.4.1.207.8.42.8.34.1.12.34
Total number of pre-authentication history entries accumulated for all the detected clients present in the detected client database.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsMaximumDetectedClientRoamHistoryEntries 1.3.6.1.4.1.207.8.42.8.34.1.12.35
Maximum number of roam history entries that can be recorded for all the detected clients present in the detected client database.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalDetectedClientRoamHistoryEntries 1.3.6.1.4.1.207.8.42.8.34.1.12.36
Total number of roam history entries accumulated for all the detected clients present in the detected client database.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsRegenerateX509CertificateAction 1.3.6.1.4.1.207.8.42.8.34.1.12.37
This action object is used to: - start - Start the certificate regeneration on the controller. - Read on this object will always return none.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsRegenerateX509CertificateStatus 1.3.6.1.4.1.207.8.42.8.34.1.12.38
Status of regenerate X.509 certificates.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-in-progress(1), started(2), in-progress(3)  

wsNetworkMutualAuthenticationStatus 1.3.6.1.4.1.207.8.42.8.34.1.12.39
Status of the mutual authentication enable/disable command. When status is Complete With Errors then the administrator may need to provision some controllers or APs separately.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-started(1), exchange-start(2), in-progress(3), provisioning-in-progress(4), exchange-in-progress(5), provisioning-complete(6), exchange-complete(7), complete-without-errors(8), complete-with-errors-refer-to-event-log-for-details(9)  

wsTotalProvisioningAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.40
Total number of APs present in the AP Provisioning database.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsMaximumProvisioningAPs 1.3.6.1.4.1.207.8.42.8.34.1.12.41
Maximum number of APs that can be maintained in the AP Provisioning database.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsGlobalStatistics 1.3.6.1.4.1.207.8.42.8.34.1.13
OBJECT IDENTIFIER    

wsTotalWLANBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.1.13.1
Total bytes transmitted across all APs managed by this controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.1.13.2
Total bytes received across all APs managed by by this controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.1.13.3
Total packets transmitted across all APs managed by this controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.1.13.4
Total packets received across all APs managed by this controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAllStatisticsReset 1.3.6.1.4.1.207.8.42.8.34.1.13.5
When we set this object to enable, all statistics maintained by controller will be cleared. Read on this object will always return disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAllStatisticsResetStatus 1.3.6.1.4.1.207.8.42.8.34.1.13.6
This object indicates the current status of controller statistics reset request. Default value is not started.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-started(0), requested(1), in-progress(2), success(3), partial-success(4), failure(5)  

wsTotalWLANBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.1.13.7
Total bytes dropped in the transmit direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.1.13.8
Total bytes dropped in the receive direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.1.13.9
Total packets dropped in the transmit direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.1.13.10
Total packets dropped in the receive direction across all APs managed by this controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANDistTunnelPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.1.13.11
Total number of packets transmitted by all APs using distributed tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsTotalWLANDistTunnelRoamedClients 1.3.6.1.4.1.207.8.42.8.34.1.13.12
Number of clients in all APs currently in roaming state using distributed tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsTotalWLANDistTunnelClientDenials 1.3.6.1.4.1.207.8.42.8.34.1.13.13
Number of client tunnel setups denied for all APs.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsPeerConfiguration 1.3.6.1.4.1.207.8.42.8.34.1.14
OBJECT IDENTIFIER    

wsPeerConfigurationGlobal 1.3.6.1.4.1.207.8.42.8.34.1.14.1
Flag to enable/disable the functionality to send global configuration parameters to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationDiscovery 1.3.6.1.4.1.207.8.42.8.34.1.14.2
Flag to enable/disable the functionality to send discovery configuration parameters to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationAPDatabase 1.3.6.1.4.1.207.8.42.8.34.1.14.3
Flag to enable/disable the functionality to send valid AP Database to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationChannelPower 1.3.6.1.4.1.207.8.42.8.34.1.14.4
Flag to enable/disable the functionality to send Channel and Power configuration to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationAPProfiles 1.3.6.1.4.1.207.8.42.8.34.1.14.5
Flag to enable/disable the functionality to send all AP profiles and networks to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationKnownClients 1.3.6.1.4.1.207.8.42.8.34.1.14.6
Flag to enable/disable the functionality to send configured known client entries to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationCaptivePortal 1.3.6.1.4.1.207.8.42.8.34.1.14.7
Flag to enable/disable the functionality to send all Captive Portal configuration to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationRadiusClient 1.3.6.1.4.1.207.8.42.8.34.1.14.8
Flag to enable/disable the functionality to send RADIUS Client configuration parameters to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationQosAcl 1.3.6.1.4.1.207.8.42.8.34.1.14.9
Flag to enable/disable the functionality to send all QoS ACL configuration to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationQosDiffServ 1.3.6.1.4.1.207.8.42.8.34.1.14.10
Flag to enable/disable the functionality to send all QoS DiffServ configuration to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationWdsGroup 1.3.6.1.4.1.207.8.42.8.34.1.14.11
Flag to enable/disable the functionality to send configured wds groups to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerConfigurationDeviceLocation 1.3.6.1.4.1.207.8.42.8.34.1.14.12
Flag to enable/disable the functionality to send configured device location parameters to a peer controller on a configuration push.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsClusterPriority 1.3.6.1.4.1.207.8.42.8.34.1.16
Preference level of the controller to become the Cluster Controller of the Peer Group.A priority of 0 means that the controller can not become cluster controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

wsAPClientQosMode 1.3.6.1.4.1.207.8.42.8.34.1.17
Flag to globally enable/disable AP quality-of-service operation for wireless clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPAutoUpgradeMode 1.3.6.1.4.1.207.8.42.8.34.1.18
Flag to enable/disable AP auto upgrade mode. This object is configurable only if the wireless controller supports both 'Integrated' and 'Independent' AP image download modes. If the controller supports only 'Integrated' mode, the default is Enable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsDistTunnelIdleTimeout 1.3.6.1.4.1.207.8.42.8.34.1.19
Time of inactivity in seconds to wait before terminating a tunnel client.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 30..3600  

wsDistTunnelMaxTimeout 1.3.6.1.4.1.207.8.42.8.34.1.20
Time in seconds to wait before terminating a tunnel client.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 30..86400  

wsDistTunnelMaxMcastRepl 1.3.6.1.4.1.207.8.42.8.34.1.21
Maximum number of multicast replications that can be performed by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..1024  

wsDistTunnelMaxClients 1.3.6.1.4.1.207.8.42.8.34.1.22
Maximum number of clients that can use tunneled through a Home AP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..8000  

wsMACAuthenticationMode 1.3.6.1.4.1.207.8.42.8.34.1.23
This object indicates whether MAC addresses in the Known Client database are granted or denied access if they are in the list, but dont have a specific action.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER whitelist(1), blacklist(2)  

wsKnownClientTable 1.3.6.1.4.1.207.8.42.8.34.1.24
This table contains entries of the known clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsKnownClientEntry

wsKnownClientEntry 1.3.6.1.4.1.207.8.42.8.34.1.24.1
The entry contains parameters of a known client.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsKnownClientEntry  

wsKnownClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.1.24.1.1
MAC address of the known client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsKnownClientAuthAction 1.3.6.1.4.1.207.8.42.8.34.1.24.1.2
This object indicates whether to grant, deny, or use global action for client authentication.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER global(1), grant(2), deny(3)  

wsKnownClientName 1.3.6.1.4.1.207.8.42.8.34.1.24.1.3
Descriptive name of the known client.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsKnownClientRowStatus 1.3.6.1.4.1.207.8.42.8.34.1.24.1.4
This object is used to create or delete entries in this table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsWidsSecurity 1.3.6.1.4.1.207.8.42.8.34.1.25
OBJECT IDENTIFIER    

wsWidsApSecurity 1.3.6.1.4.1.207.8.42.8.34.1.25.1
OBJECT IDENTIFIER    

rogueAdminConfig 1.3.6.1.4.1.207.8.42.8.34.1.25.1.1
Report the AP as rogue in the RF Scan if the local database indicates that the AP is rogue. Can not be disabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1)  

rogueUnknownApManagedSsid 1.3.6.1.4.1.207.8.42.8.34.1.25.1.2
Enable rogue reporting for unknown AP's detected with a managed SSID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueFakeManagedApManagedSsid 1.3.6.1.4.1.207.8.42.8.34.1.25.1.3
Enable rogue reporting for fake managed AP's detected with a managed SSID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueManagedApNoSsid 1.3.6.1.4.1.207.8.42.8.34.1.25.1.4
Enable rogue reporting of all APs detected with no SSID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueManagedApInvalidChannel 1.3.6.1.4.1.207.8.42.8.34.1.25.1.5
Enable rogue reporting of fake managed AP's detected with an invalid channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueManagedSsidInvalidSecurity 1.3.6.1.4.1.207.8.42.8.34.1.25.1.6
Enable rogue reporting of AP's detected with managed SSID's and an invalid security configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueManagedApInvalidSsid 1.3.6.1.4.1.207.8.42.8.34.1.25.1.7
Enable rogue reporting of managed AP's with an invalid SSID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueApIllegalChannel 1.3.6.1.4.1.207.8.42.8.34.1.25.1.8
Enable rogue reporting of AP's operating on an illegal channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueStandaloneApInvalidConfig 1.3.6.1.4.1.207.8.42.8.34.1.25.1.9
Enable rogue reporting of standalone AP's operating with an unexpected configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueUnexpectedWdsDevice 1.3.6.1.4.1.207.8.42.8.34.1.25.1.10
Enable rogue reporting of unexpected WDS devices.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rogueUnmanagedApWiredNetwork 1.3.6.1.4.1.207.8.42.8.34.1.25.1.11
Enable rogue reporting of unmanaged AP's on a wired network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wiredNetworkDetectionInterval 1.3.6.1.4.1.207.8.42.8.34.1.25.1.12
Minimum number of seconds that the AP waits before starting a new wired network detection cycle. A value of 0 disables wired network detection.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..3600  

rogueDetectedTrapInterval 1.3.6.1.4.1.207.8.42.8.34.1.25.1.13
The interval in seconds between transmissions of the trap telling the administrator that Rogues are present in the RF Scan database. A configured value of 0 disables the trap from being sent. .
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 60..3600  

apDeauthenticationAttack 1.3.6.1.4.1.207.8.42.8.34.1.25.1.14
Enable the AP de-authentication attack.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsWidsClientSecurity 1.3.6.1.4.1.207.8.42.8.34.1.25.2
OBJECT IDENTIFIER    

rogueDetectedTrapIntvl 1.3.6.1.4.1.207.8.42.8.34.1.25.2.1
The interval in seconds between transmissions of the trap telling the administrator that Rogues are present in the Rogue Clients are present in the Detected Clients Database. A configured value of 0 disables the trap from being sent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 60..3600  

knownClientDatabaseTest 1.3.6.1.4.1.207.8.42.8.34.1.25.2.2
Report the client as rogue if it fails the Known Client Database Test.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

authReqTransmitRate 1.3.6.1.4.1.207.8.42.8.34.1.25.2.3
Report the client as rogue if it exceeds configured rate for transmitting 802.11 authentication requests.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

probeReqTransmitRate 1.3.6.1.4.1.207.8.42.8.34.1.25.2.4
Report the client as rogue if it exceeds configured rate for transmitting probe requests.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

deauthReqTransmitRate 1.3.6.1.4.1.207.8.42.8.34.1.25.2.5
Report the client as rogue if it exceeds configured rate for transmitting 802.11 deauthentication requests.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

maxFailingAuthentication 1.3.6.1.4.1.207.8.42.8.34.1.25.2.6
Report the client as rogue if it exceeds maximum number of failing authentications.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

authWithUnknownAP 1.3.6.1.4.1.207.8.42.8.34.1.25.2.7
Report the client as rogue if it is authenticated with an unknown AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

clientThreatMitigation 1.3.6.1.4.1.207.8.42.8.34.1.25.2.8
Transmission of de-authentication messages to known clients associated with unknown APs. The Known Client test must also be enabled in order for the mitigation to take place.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

deauthThresholdInterval 1.3.6.1.4.1.207.8.42.8.34.1.25.2.9
Number of seconds for counting the de-authentication messages.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3600  

deauthThresholdValue 1.3.6.1.4.1.207.8.42.8.34.1.25.2.10
If controller receives more than specified de-auth messages during the threshold interval the test triggers the client to be reported as rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..99999  

authThresholdInterval 1.3.6.1.4.1.207.8.42.8.34.1.25.2.11
Number of seconds for counting the authentication messages.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3600  

authThresholdValue 1.3.6.1.4.1.207.8.42.8.34.1.25.2.12
If controller receives more than specified auth messages during the threshold interval the test triggers the client to be reported as rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..99999  

probeThresholdInterval 1.3.6.1.4.1.207.8.42.8.34.1.25.2.13
Number of seconds for counting the probe messages.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3600  

probeThresholdValue 1.3.6.1.4.1.207.8.42.8.34.1.25.2.14
If controller receives more than specified probe messages during the threshold interval the test triggers the client to be reported as rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..99999  

authFailureThreshold 1.3.6.1.4.1.207.8.42.8.34.1.25.2.15
The number of 802.1X authentication failures that triggers the client to be reported as rogue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..99999  

knownClientDatabaseLocation 1.3.6.1.4.1.207.8.42.8.34.1.25.2.16
The location of Known Client Database. If the value is local then Known Client Database is located in the local controller. Otherwise the database is located in the RADIUS Server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), radius(2)  

knownClientDatabaseRadiusServerName 1.3.6.1.4.1.207.8.42.8.34.1.25.2.17
Name of the RADIUS server used for Known Client database This is used when knownClientDatabaseLocation is set to 'radius'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

knownClientDatabaseRadiusServerStatus 1.3.6.1.4.1.207.8.42.8.34.1.25.2.18
Indicates whether the specified named RADIUS Authentication server is configured in the RADIUS Client configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-configured(1), configured(2)  

notInOUIDatabase 1.3.6.1.4.1.207.8.42.8.34.1.25.2.19
Report the client as rogue if it's OUI is not present in the OUI Database.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsGlobalRadiusConfiguration 1.3.6.1.4.1.207.8.42.8.34.1.26
OBJECT IDENTIFIER    

wsRadiusConfiguration 1.3.6.1.4.1.207.8.42.8.34.1.26.1
OBJECT IDENTIFIER    

wsAuthRadiusServerName 1.3.6.1.4.1.207.8.42.8.34.1.26.1.1
Name of the RADIUS server used for AP authentications as well as client authentications when a network-level RADIUS server is not defined.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsAuthRadiusServerConfiguredStatus 1.3.6.1.4.1.207.8.42.8.34.1.26.1.2
Indicates whether the specified named RADIUS Authentication server is configured in the RADIUS Client configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-configured(1), configured(2)  

wsAcctRadiusServerName 1.3.6.1.4.1.207.8.42.8.34.1.26.1.3
Name of the RADIUS server used for reporting wireless client associations and disassociations when a network-level RADIUS accounting server is not defined.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsAcctRadiusServerConfiguredStatus 1.3.6.1.4.1.207.8.42.8.34.1.26.1.4
Indicates whether the specified named RADIUS Accounting server is configured in the RADIUS Client configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-configured(1), configured(2)  

wsRadiusAcctMode 1.3.6.1.4.1.207.8.42.8.34.1.26.1.5
Flag to indicate whether or not RADIUS accounting is enabled for wireless clients.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAutoIPAssignMode 1.3.6.1.4.1.207.8.42.8.34.1.29
Flag indicating whether the Wireless feature should automatically assign an IP address from one of the active interfaces or whether the IP address is manually assigned.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsSwitchStaticIPAddress 1.3.6.1.4.1.207.8.42.8.34.1.30
Statically assigned IPv4 address for the Wireless feature. If Auto IP Assignment is true then this setting is ignored.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsGlobalTspecConfiguration 1.3.6.1.4.1.207.8.42.8.34.1.31
OBJECT IDENTIFIER    

wsTspecViolationReportInterval 1.3.6.1.4.1.207.8.42.8.34.1.31.1
Specifies the time period at which wireless clients detected as using admission-controlled resources without proper TSPEC authorization are reported via the system logging and SNMP trap mechanisms. If a violating client disassociates before the next report interval, it is reported upon disassociation. This object is specified in seconds, with a default value of 300 (5 minutes). Setting this object value to 0 disables TSPEC violation reporting.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..900  

wsSwitchStatusTable 1.3.6.1.4.1.207.8.42.8.34.1.27
This table contain access point and client status parameters of peer controllers of wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwitchStatusEntry

wsSwitchStatusEntry 1.3.6.1.4.1.207.8.42.8.34.1.27.1
Each entry describes the access point and client status parameters of each peer of wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwitchStatusEntry  

wsSwitchIPAddress 1.3.6.1.4.1.207.8.42.8.34.1.27.1.1
This object represents wireless controller IP address. When wireless mode is in disabled state, return entry will be none.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsSwitchClusterPriority 1.3.6.1.4.1.207.8.42.8.34.1.27.1.2
Preference level of the controller to become the Cluster Controller of the Peer Group.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

wsSwitchAPImageDownloadMode 1.3.6.1.4.1.207.8.42.8.34.1.27.1.3
The AP image download mode supported by the wireless controller. The displayed mode can be one of the following: Integrated - The controller supports Integrated mode. In this mode, the AP code is located on the controller, and the controller automatically updates the code on APs it manages. Independent - The controller supports Independent mode. In this mode, the AP code is on a TFTP server, and the download is triggered from the cluster controller. Integrated, Independent - The controller supports both modes. Note that this field displays the mode only if wireless controllers that support Independent and Integrated AP Image Download modes co-exist in the network.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsSwitchTotalAPs 1.3.6.1.4.1.207.8.42.8.34.1.27.1.4
Sum of all the WS managed APs, connection failed APs, and discovered APs in the database of specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..48  

wsSwitchManagedAPs 1.3.6.1.4.1.207.8.42.8.34.1.27.1.5
Total number of WS managed APs currently authenticated, configured and have an active connection with the specifed controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..48  

wsSwitchDiscoveredAPs 1.3.6.1.4.1.207.8.42.8.34.1.27.1.6
Number of APs that are connected to the specified controller, but have not been completely configured.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..48  

wsSwitchConnectionFailedAPs 1.3.6.1.4.1.207.8.42.8.34.1.27.1.7
Number of APs that were previously authenticated and managed, but currently do not have connection with the specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..48  

wsSwitchMaximumManagedAPs 1.3.6.1.4.1.207.8.42.8.34.1.27.1.8
Maximum number of APs that the specified controller can manage.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsSwitchTotalClients 1.3.6.1.4.1.207.8.42.8.34.1.27.1.9
Total number of clients in the database that include clients with an associated, authenticated and disassociated status.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..8192  

wsSwitchAuthenticatedClients 1.3.6.1.4.1.207.8.42.8.34.1.27.1.10
Total number of authenticated clients across all APs managed by the specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..8192  

wsSwitchWLANUtilization 1.3.6.1.4.1.207.8.42.8.34.1.27.1.11
Total network utilization across all APs managed by the specifed controller.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100  

wsSwitchDistTunnelClients 1.3.6.1.4.1.207.8.42.8.34.1.27.1.12
Number of clients that are currently sending and receiving packets via distributed tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsSwitchStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.1.28
This table contain WLAN statistics for every controller in the peer group. Only Cluster Controller can hold the entries for peer controllers. The controller which is not a Cluster Controller only keep statistics local to it.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwitchStatisticsEntry

wsSwitchStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.1.28.1
Each entry describe WLAN statistics of specified controller in the wireless system.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwitchStatisticsEntry  

wsSwitchWLANBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.1.28.1.1
Total bytes transmitted across all APs managed by the specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANBytesReceived 1.3.6.1.4.1.207.8.42.8.34.1.28.1.2
Total bytes received across all APs managed by the specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.1.28.1.3
Total packets transmitted across all APs managed by the specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANPktsReceived 1.3.6.1.4.1.207.8.42.8.34.1.28.1.4
Total packets received across all APs managed by the specified controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.1.28.1.5
Total bytes dropped in the transmit direction across all APs managed by the specified controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.1.28.1.6
Total bytes dropped in the receive direction across all APs managed the specified controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.1.28.1.7
Total packets dropped in the transmit direction across all APs managed by the specified controller. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsSwitchWLANPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.1.28.1.8
Total packets dropped in the receive direction across all APs managed by the specified controller. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

networkMutualAuthMode 1.3.6.1.4.1.207.8.42.8.34.1.32
Flag to enable/disable mutual authentication of the Wireless controllers and Access Points in the network.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

unmanagedAPReprovisioning 1.3.6.1.4.1.207.8.42.8.34.1.33
Flag to enable/disable reprovisioning of APs when in unmanaged mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

apProvisionDbAgeTime 1.3.6.1.4.1.207.8.42.8.34.1.34
Time in hours to wait without hearing any updates for the APs before removing them from the provisioning database.A value of 0 in input range means that the entry never ages out.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..240  

switchProvisioning 1.3.6.1.4.1.207.8.42.8.34.1.35
Flag to enable/disable controller provisioning.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsIpBasePort 1.3.6.1.4.1.207.8.42.8.34.1.36
Base IP port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65000  

devLocMeasurementSys 1.3.6.1.4.1.207.8.42.8.34.1.37
Measurement system in english/metric.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER metric(1), english(2)  

devLocRfScanLocMode 1.3.6.1.4.1.207.8.42.8.34.1.38
Flag to enable/disable RF Scan location Mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

devLocRfScanLocInterval 1.3.6.1.4.1.207.8.42.8.34.1.39
Number of seconds between iterations of triangulation table device location protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 30..3600  

wsIPPollMode 1.3.6.1.4.1.207.8.42.8.34.2.1
Flag to enable/disable IP based discovery of APs and peer controllers.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsL2DiscoveryMode 1.3.6.1.4.1.207.8.42.8.34.2.2
Flag to enable/disable L2 discovery of APs and peer controllers.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsIPPollListTable 1.3.6.1.4.1.207.8.42.8.34.2.3
This table contains IP addresses to poll on the network.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsIPPollListEntry

wsIPPollListEntry 1.3.6.1.4.1.207.8.42.8.34.2.3.1
An IP address list that can be configured globally on the wireless controller to define which IP addresses to poll in order to discover new APs and peer controllers. This list is used when discovery via IP Polling is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsIPPollListEntry  

wsPollIpAddress 1.3.6.1.4.1.207.8.42.8.34.2.3.1.1
IP address of an AP or controller to poll.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsPollIPStatus 1.3.6.1.4.1.207.8.42.8.34.2.3.1.2
Indicates whether or not the controller reached this IP address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-polled(1), polled(2), discovered(3), discovered-failed(4)  

wsIPPollRowStatus 1.3.6.1.4.1.207.8.42.8.34.2.3.1.3
This object is used to create and delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsL2DiscoveryVlanListTable 1.3.6.1.4.1.207.8.42.8.34.2.4
This table contains the list of VLANs on which to send L2 discovery multicast packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsL2DiscoveryVlanListEntry

wsL2DiscoveryVlanListEntry 1.3.6.1.4.1.207.8.42.8.34.2.4.1
A list of VLANs on which to send L2 discovery multicast frames when L2 broadcast discovery mode is enabled. The entries in this table are limited to sixteen. By default there will be one entry in this table with wsL2DiscoveryVlanId equal to one. This entry can neither be created nor deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsL2DiscoveryVlanListEntry  

wsL2DiscoveryVlanId 1.3.6.1.4.1.207.8.42.8.34.2.4.1.1
VLAN Id on which controller will send L2 discovery multicast frames.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4094  

wsL2DiscoveryVlanRowStatus 1.3.6.1.4.1.207.8.42.8.34.2.4.1.2
This variable is used to create and delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsIPPollListMaxNumOfEntries 1.3.6.1.4.1.207.8.42.8.34.2.5
Maximum number of IP discovery entries allowed to be configured.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..256  

wsIPPollListNumOfConfigEntries 1.3.6.1.4.1.207.8.42.8.34.2.6
Total number of entries configured IP discovery entries.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..256  

wsIPPollListNumOfPolledEntries 1.3.6.1.4.1.207.8.42.8.34.2.7
Total number of polled entries in the IP discovery list.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..256  

wsIPPollListNumOfNotPolledEntries 1.3.6.1.4.1.207.8.42.8.34.2.8
Total number of not-polled entries in the IP discovery list.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..256  

wsIPPollListNumOfDiscoveredEntries 1.3.6.1.4.1.207.8.42.8.34.2.9
Total number of discovered entries in the IP discovery list.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..256  

wsIPPollListNumOfDiscoveredFailedEntries 1.3.6.1.4.1.207.8.42.8.34.2.10
Total number of discovered-failed entries in the IP discovery list.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..256  

wsL2CentTnnlVlanListTable 1.3.6.1.4.1.207.8.42.8.34.13.1
This table contains the list of layer 2 tunneled VLANs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsL2CentTnnlVlanListEntry

wsL2CentTnnlVlanListEntry 1.3.6.1.4.1.207.8.42.8.34.13.1.1
A list of VLANs on which all frames are tunneled. The entries in this table are limited to 64.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsL2CentTnnlVlanListEntry  

wsL2CentTnnlVlanId 1.3.6.1.4.1.207.8.42.8.34.13.1.1.1
VLAN ID on which all frames are tunneled.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

wsL2CentTnnlVlanRowStatus 1.3.6.1.4.1.207.8.42.8.34.13.1.1.2
This variable is used to create and delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsOuiTable 1.3.6.1.4.1.207.8.42.8.34.14.1
This table contains the list of OUIs that have been configured by the administrator. The entries in this table are limited to 64.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsOuiEntry

wsOuiEntry 1.3.6.1.4.1.207.8.42.8.34.14.1.1
A list of OUIs. Each entry contains OUI and descriptive name of the wireless device manufacturer. The administrator can enter up to 64 user-defined OUIs.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsOuiEntry  

wsOuiValue 1.3.6.1.4.1.207.8.42.8.34.14.1.1.1
The OUI value for the AP or the client. Least significant bit of the first byte must be zero.
Status: current Access: read-only
OBJECT-TYPE    
  WsOui  

wsOuiDescription 1.3.6.1.4.1.207.8.42.8.34.14.1.1.2
The descriptive name for the manufacturer of AP or wireless client adapter.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsOuiRowStatus 1.3.6.1.4.1.207.8.42.8.34.14.1.1.3
This variable is used to create and delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsAPProfileTable 1.3.6.1.4.1.207.8.42.8.34.3.1
The following parameters can be configured within an AP configuration profile. A profile is used to replicate a single AP configuration across multiple managed APs. Modification or deletion is not allowed if the profile is assigned to one or more managed APs except wsCopyAPProfileToProfileId.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileEntry

wsAPProfileEntry 1.3.6.1.4.1.207.8.42.8.34.3.1.1
Each entry has parameters that can be configured within an AP configuration profile. A profile is used to replicate a single AP configuration across multiple managed APs, and is indexed by an integer Id.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileEntry  

wsAPProfileId 1.3.6.1.4.1.207.8.42.8.34.3.1.1.1
Unique AP Profile Id for each entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..16  

wsAPProfileName 1.3.6.1.4.1.207.8.42.8.34.3.1.1.2
AP configuration profile name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAPProfileState 1.3.6.1.4.1.207.8.42.8.34.3.1.1.3
Indicates current state of AP Profile.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), configured(1), requested(2), in-progress(3), associated(4)  

wsAPProfileRowStatus 1.3.6.1.4.1.207.8.42.8.34.3.1.1.8
This object is used to create or delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsCopyAPProfileToProfileId 1.3.6.1.4.1.207.8.42.8.34.3.1.1.9
This object copies the AP profile configuration to the specified valid AP Profile Id. If specified Profile Id is already assigned to one or more managed APs, the operation is not allowed. Read on this object will always return zero.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

wsAPProfileApply 1.3.6.1.4.1.207.8.42.8.34.3.1.1.10
This object is used to apply the AP profile configuration. Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), apply(2)  

wsAPHardwareTypeID 1.3.6.1.4.1.207.8.42.8.34.3.1.1.11
AP Hardware type ID associated with each entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..6  

wsAPWiredDetectionVlanId 1.3.6.1.4.1.207.8.42.8.34.3.1.1.12
VLAN ID that is used to send packets on the wire that enable the system to discover rogue APs attached to the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4094  

wsAPProfileDisconnAPFwdingMode 1.3.6.1.4.1.207.8.42.8.34.3.1.1.13
Flag to enable/disable Disconnected AP Data Forwarding Mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProfileDisconnAPMgmtMode 1.3.6.1.4.1.207.8.42.8.34.3.1.1.14
Flag to enable/disable Disconnected AP Management Mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProfileAeroScoutSupportMode 1.3.6.1.4.1.207.8.42.8.34.3.1.1.15
Flag to enable/disable AE Protocol Support Mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProfileRadioTable 1.3.6.1.4.1.207.8.42.8.34.3.3
This table contains parameters that can be configured with in an AP Profile per radio interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioEntry

wsAPProfileRadioEntry 1.3.6.1.4.1.207.8.42.8.34.3.3.1
Each entry in this table represents parameters that can be configured with in an AP profile per radio interface. Two entries in this table will get created automatically for each AP profile being created in wsAPProfileTable. Whenever AP profile entry is deleted, corresponding radio profile entries will get deleted automatically.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioEntry  

wsAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.3.3.1.1
AP physical radio interface number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAPRadioAdminMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.2
Flag to indicate whether the radio is operational.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wsAPRadioFrequency 1.3.6.1.4.1.207.8.42.8.34.3.3.1.3
Indicates which physical layer technology to use on radio. Default value for radio 1 is 'ieee802dot11bgn' and default value for radio 2 is 'ieee802dot11an'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ieee802dot11a(1), ieee802dot11bg(2), ieee802dot11an(3), ieee802dot11bgn(4), fiveGHzIeee802dot11n(5), twoDotFourGHzIeee802dot11n(6), fiveGHzIeee802dot11anac(7), fiveGHzIeee802dot11nac(8)  

wsAPRadioOtherChannelsScanMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.4
When Sentry mode is disabled this flag controls whether the radio moves away from the operating channel while doing scans. When this mode is disabled the radio scans only on the operating channel. When sentry mode is enabled on the radio this parameter is ignored.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioOtherChannelsScanInterval 1.3.6.1.4.1.207.8.42.8.34.3.3.1.5
If scan mode is enable, indicates how often the radio leaves its operational channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 30..120  

wsAPRadioSentryScanMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.6
When Sentry mode is enabled the radio doesn't do any data forwarding, but only periodically scan channels for rogues. The length of time spent on each channels controlled by the 'scan duration' time.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioSentryScanChannel 1.3.6.1.4.1.207.8.42.8.34.3.3.1.7
If scanning is enabled, this object indicates on which frequencies to scan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ieee802dot11an(1), ieee802dot11bORgn(2), all(3)  

wsAPRadioScanDuration 1.3.6.1.4.1.207.8.42.8.34.3.3.1.8
Indicates how long the radio can scan before returning to its operational channel. The default value is 10ms.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 10..2000  

wsAPRadioRateLimitMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.9
This object enables/disables rate limit for broadcast and multicast traffic transmitted across the network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioRateLimit 1.3.6.1.4.1.207.8.42.8.34.3.3.1.10
Allowed rate limit for broadcast/multicast traffic transmitted across the network. Broadcast/multicast traffic below this limit is transmitted normally.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..50  

wsAPRadioRateLimitBurst 1.3.6.1.4.1.207.8.42.8.34.3.3.1.11
Broadcast/multicast traffic can occur in bursts up to this value before all traffic is considered to exceed the limit.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..75  

wsAPRadioBeaconInterval 1.3.6.1.4.1.207.8.42.8.34.3.3.1.12
Interval at which the AP transmit beacon frames.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 20..2000  

wsAPRadioDTIMPeriod 1.3.6.1.4.1.207.8.42.8.34.3.3.1.13
Indicates the number of beacons between Delivery Traffic Indication MAP(DTIM). DTIM indicates buffered broadcast/multicast traffic on an AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsAPRadioFragmentationThreshold 1.3.6.1.4.1.207.8.42.8.34.3.3.1.14
This object limits the size of packets transmitted over the network. Only even values are allowed in the defined range.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 256..2346  

wsAPRadioRTSThreshold 1.3.6.1.4.1.207.8.42.8.34.3.3.1.15
This object indicates the number of octets in an MAC Protocol Data Unit(MPDU), below which an request to send(RTS)/clear to send(CTS) handshake shall not be performed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2347  

wsAPRadioShortRetryLimit 1.3.6.1.4.1.207.8.42.8.34.3.3.1.16
This object indicates the maximum number of transmission attempts on frame sizes less than or equal to the RTS threshold. Set action for this object will be supported in next release.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsAPRadioLongRetryLimit 1.3.6.1.4.1.207.8.42.8.34.3.3.1.17
This object indicates the maximum number of transmission attempts on frame sizes greater than the RTS threshold. Set action for this object will be supported in next release.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsAPRadioMaxTransmitLifetime 1.3.6.1.4.1.207.8.42.8.34.3.3.1.18
This object indicates the elapsed time after the initial transmission of MAC Service Data Unit(MSDU), after which further attempts to transmit the MSDU shall be terminated. Set action for this object will be supported in next release.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsAPRadioMaxReceiveLifetime 1.3.6.1.4.1.207.8.42.8.34.3.3.1.19
This object indicates the elapsed time after the initial reception of a fragmented MAC Management Protocol Data Unit(MMPDU) or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. Set action for this object will be supported in next release.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsAPRadioMaxClients 1.3.6.1.4.1.207.8.42.8.34.3.3.1.20
Maximum number of client stations that can simultaneously get associated on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..200  

wsAPRadioAutoPowerMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.21
Flag to indicate power is automatically adjusted by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioTxPower 1.3.6.1.4.1.207.8.42.8.34.3.3.1.22
If auto power mode is disabled, this object indicates a fixed power setting for the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

wsAPRadioWMMMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.23
Flag to enable/disable Wi-Fi MultiMedia Mode. When enabled, QOS settings affect both downstream traffic to the sation and upstream traffic to the AP. When disabled, QOS only applies to downstream traffic.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioLoadBalancingMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.24
Flag to indicate that AP will load balance users on this radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioUtilization 1.3.6.1.4.1.207.8.42.8.34.3.3.1.25
If load balancing is enabled, percentage of network utilization allowed on the radio before clients are denied. This value is displayed in percentage.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

wsAPRadioAutoChannelMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.26
Flag to indicate whether initial AP radio channel assignment can be automatically adjusted by controller due to changes in radio performance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioStationIsolationMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.27
Flag to indicate whether Station Isolation is enabled on the Radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioChannelBandwidth 1.3.6.1.4.1.207.8.42.8.34.3.3.1.28
Bandwidth used in the channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twentyMHz(1), fortyMHz(2), eightyMHz(3)  

wsAPRadioPrimaryChannel 1.3.6.1.4.1.207.8.42.8.34.3.3.1.29
Specify relative location of Primary Channel in the 40 MHz channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER upper(1), lower(2)  

wsAPRadioProtectionMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.30
Turn on/off Protection mechanisms.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auto(1), off(2)  

wsAPRadioShortGuardInterval 1.3.6.1.4.1.207.8.42.8.34.3.3.1.31
Dead time, in nanoseconds, between OFDM symbols which prevents Inter-Symbol and Inter-Carrier Interference (ISI, ICI). The short guard interval, when enabled, is 400ns and the standard guard interval, when disabled, is 800ns.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

wsAPRadioSTBCMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.32
The Space Time Block Code (STBC) Mode enables the AP to send the same data stream on multiple antennas at the same time. This is different from MIMO where the data stream is divided between two antennas.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wsAPRadioMulticastTxRate 1.3.6.1.4.1.207.8.42.8.34.3.3.1.33
Indicates the data rate AP will send multicast data to its client stations represented by a count from 2 - 127, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 63.5 Mbit/s. 0 represents automatic rate selection. For Example : Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 2..127  

wsAPRadioAPSDMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.34
Automatic Power Save Delivery Mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioNoAckMode 1.3.6.1.4.1.207.8.42.8.34.3.3.1.35
Don't send acknowledgement to correctly received frames.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioResourceMeasEnabled 1.3.6.1.4.1.207.8.42.8.34.3.3.1.36
Flag to enable/disable Radio Resource Management (RRM) as defined in the IEEE 802.11k specification. RRM allows wireless clients to request adjustments and report conditions regarding channel load and neighbor detection.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioQOSEDCATemplate 1.3.6.1.4.1.207.8.42.8.34.3.3.1.37
This object indicates the QOS template choice in effect for the profile and radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER custom(0), factory-default(1), voice(2)  

wsAPRadioMinTxPower 1.3.6.1.4.1.207.8.42.8.34.3.3.1.38
Minimum Transmit Power that can be set by APA on the radio. Default Value is 20% for 2.4Ghz Radio and 100% for 5Ghz radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

wsAPProfileRadioSupportedRatesTable 1.3.6.1.4.1.207.8.42.8.34.3.4
This table represents the supported data rates by AP Profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioSupportedRatesEntry

wsAPProfileRadioSupportedRatesEntry 1.3.6.1.4.1.207.8.42.8.34.3.4.1
Each entry in this table represents supported data rate.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioSupportedRatesEntry  

wsSupportedDataRate 1.3.6.1.4.1.207.8.42.8.34.3.4.1.1
Indicates the data rate, AP will actually support in setting up communications with client stations represented by a count from 2 - 127, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 63.5 Mbit/s. Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..127  

wsAPProfileRadioSupportedDataMode 1.3.6.1.4.1.207.8.42.8.34.3.4.1.2
Displays supported data rate by an AP Profile. Supported rates by an AP Profile depends on physical mode of the radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER supported(1), not-supported(2)  

wsAPProfileRadioBasicRatesTable 1.3.6.1.4.1.207.8.42.8.34.3.5
This table represents the basic data rates advertised by an AP Profile.Stations connecting to this AP must support this set of data rates.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioBasicRatesEntry

wsAPProfileRadioBasicRatesEntry 1.3.6.1.4.1.207.8.42.8.34.3.5.1
Each entry in this table represents basic data rate.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioBasicRatesEntry  

wsBasicDataRate 1.3.6.1.4.1.207.8.42.8.34.3.5.1.1
Indicates the basic data rate, AP will actually advertise to its client stations represented by a count from 2 - 127, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 63.5 Mbit/s. For Example : Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..127  

wsAPProfileRadioBasicDataMode 1.3.6.1.4.1.207.8.42.8.34.3.5.1.2
Displays basic data rate advertised by an AP Profile. Basic rate depends on physical mode of the radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER basic(1), not-basic(2)  

wsAPProfileVAPTable 1.3.6.1.4.1.207.8.42.8.34.3.6
This table is about VAP profile configuration. When AP profile entry is created, corresponding eight VAP entries will get created for each radio. When AP Profile entry is get deleted, corresponding VAP entries will be deleted automatically.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileVAPEntry

wsAPProfileVAPEntry 1.3.6.1.4.1.207.8.42.8.34.3.6.1
Each entry in this table represents VAP profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileVAPEntry  

wsVAPId 1.3.6.1.4.1.207.8.42.8.34.3.6.1.1
Index of the VAP with respect to the radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

wsVAPMode 1.3.6.1.4.1.207.8.42.8.34.3.6.1.2
Flag to enable/disable VAP. VAP0 can not be disabled. In order to disable VAP0, radio must be turned off.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsVAPNetworkId 1.3.6.1.4.1.207.8.42.8.34.3.6.1.3
Network configuration assigned to the VAP. By default, VAP 0 to 7 are assigned to Network Ids 1 to 8 in order.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..32  

wsAPProfileQOSTable 1.3.6.1.4.1.207.8.42.8.34.3.7
This table displays QOS configuration. Enhanced Distributed Channel Access(EDCA) parameters of an AP affect downstream traffic from AP to the client station. Station EDCA parameters affect upstream traffic from the client station to an AP. Creation of AP Profile creates corresponding four qos profiles with default values for each radio. Deletion of AP Profile deletes the corresponding QOS entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileQOSEntry

wsAPProfileQOSEntry 1.3.6.1.4.1.207.8.42.8.34.3.7.1
Each entry in this table represents QOS profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileQOSEntry  

wsQOSQueueId 1.3.6.1.4.1.207.8.42.8.34.3.7.1.1
This object indicates QOS Queue Id.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER voice(0), video(1), besteffort(2), background(3)  

wsAPEDCAAIFS 1.3.6.1.4.1.207.8.42.8.34.3.7.1.2
Specifies the wait time for data frames. The default values for each QOS Id is mentioned below: voice(0) - 1 msec video(1) - 1 msec besteffort(2) - 3 msec background(3) - 7 msec
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsAPEDCAMinContentionWindow 1.3.6.1.4.1.207.8.42.8.34.3.7.1.3
Specifies the upper limit of a range from which the initial random backoff wait time is determined. The default values for each QOS Id is mentioned below: voice(0) - 3 msec video(1) - 7 msec besteffort(2) - 15 msec background(3) - 15 msec
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER one(1), three(3), seven(7), fifteen(15), thirty-one(31), sixty-three(63), onetwenty-seven(127), twofifty-five(255), fivehundred-eleven(511), onethousand-twentythree(1023)  

wsAPEDCAMaxContentionWindow 1.3.6.1.4.1.207.8.42.8.34.3.7.1.4
Specifies the upper limit for the doubling of the random backoff value, doubling continues until either the data frame is sent or this value is reached. The default values for each QOS Id is mentioned below: voice(0) - 7 msec video(1) - 15 msec besteffort(2) - 63 msec background(3) - 1023 msec
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER one(1), three(3), seven(7), fifteen(15), thirty-one(31), sixty-three(63), onetwenty-seven(127), twofifty-five(255), fivehundred-eleven(511), onethousand-twentythree(1023)  

wsAPEDCAMaxBurst 1.3.6.1.4.1.207.8.42.8.34.3.7.1.5
Specifies the maximum burst length allowed for packet bursts on the wireless network. The default values for each QOS Id is mentioned below: voice(0) - 1500 micro sec video(1) - 3000 micro sec besteffort(2) - 0 micro sec background(3) - 0 micro sec
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999900  

wsStationEDCAAIFS 1.3.6.1.4.1.207.8.42.8.34.3.7.1.6
Specifies the wait time for data frames. The default values for each QOS Id is mentioned below: voice(0) - 2 msec video(1) - 2 msec besteffort(2) - 3 msec background(3) - 7 msec
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsStationEDCAMinContentionWindow 1.3.6.1.4.1.207.8.42.8.34.3.7.1.7
Specifies the upper limit of a range from which the initial random backoff wait time is determined for station. The default values for each QOS Id is mentioned below: voice(0) - 3 msec video(1) - 7 msec besteffort(2) - 15 msec background(3) - 15 msec
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER one(1), three(3), seven(7), fifteen(15), thirty-one(31), sixty-three(63), onetwenty-seven(127), twofifty-five(255), fivehundred-eleven(511), onethousand-twentythree(1023)  

wsStationEDCAMaxContentionWindow 1.3.6.1.4.1.207.8.42.8.34.3.7.1.8
Specifies the upper limit for the doubling of the random backoff value, doubling continues until either the data frame is sent or this value is reached. The default values for each QOS Id is mentioned below: voice(0) - 7 msec video(1) - 15 msec besteffort(2) - 63 msec background(3) - 1023 msec
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER one(1), three(3), seven(7), fifteen(15), thirty-one(31), sixty-three(63), onetwenty-seven(127), twofifty-five(255), fivehundred-eleven(511), onethousand-twentythree(1023)  

wsStationEDCATXOPLimit 1.3.6.1.4.1.207.8.42.8.34.3.7.1.9
Specifies an interval of the time when a Wireless Multimedia Extensions(WME) client station has the right to initiate transmissions on to the wireless medium. The default values for each QOS Id is mentioned below: voice(0) - 47 msec video(1) - 94 msec besteffort(2) - 0 msec background(3) - 0 msec
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

wsNetworkTable 1.3.6.1.4.1.207.8.42.8.34.3.8
The following parameters can be configured for each network. A network may be assigned to one or more VAPs within an AP configuration profile. The first eight networks are created with default values, and cannot be deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsNetworkEntry

wsNetworkEntry 1.3.6.1.4.1.207.8.42.8.34.3.8.1
Each entry in this table is associated with a unique network Id.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsNetworkEntry  

wsNetworkId 1.3.6.1.4.1.207.8.42.8.34.3.8.1.1
Network Id used to uniquely identify the network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..32  

wsNetworkIdRowStatus 1.3.6.1.4.1.207.8.42.8.34.3.8.1.2
Add Network ID to the network configuration table. The first 16 network configurations are created by default, they are applied to VAP-0 through VAP-15 in order on each radio when a new AP configuration profile is created (one default network configuration exists per VAP ID).
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsNetworkSSID 1.3.6.1.4.1.207.8.42.8.34.3.8.1.3
This object indicates Service Set ID specific to this Network. The first network is configured with a default SSID 'Guest Network', the rest of the networks have default SSIDs assigned based on the Network Id.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsNetworkDefaultVLANId 1.3.6.1.4.1.207.8.42.8.34.3.8.1.4
Default VLAN Id assigned to the Network. The default VLAN is used if RADIUS based authentication is not configured for the network or the RADIUS server does not return a VLAN for a specific client.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4094  

wsNetworkHideSSIDMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.5
Flag to enable/disable inclusion of SSID in AP beacons.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkDenyBcastMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.6
If client broadcasts probe requests to all available SSIDs this option controls whether or not the system will respond to the probe request. The 'disable' mode means that the system responds.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkMACAuthenticationMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.10
This object indicates mode to disable, or enable and specify lookup method for authentication via client MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), radius(2), disable(3)  

wsNetworkRadiusAccountingMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.14
Flag to enable/disable RADIUS accounting authentication for users on this network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkSecurityMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.15
Specifies authentication and encryption mode on this network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), wepStatic(2), wep802dot1x(3), wpaPersonal(4), wpaEnterprise(5)  

wsNetworkWPAVersionsSupported 1.3.6.1.4.1.207.8.42.8.34.3.8.1.16
If Wi-Fi Protected Access(WPA) encryption mode is enabled, this object indicates the versions of WPA allowed by clients on this network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER wpa(1), wpa2(2), both(3)  

wsNetworkWPACipherSuites 1.3.6.1.4.1.207.8.42.8.34.3.8.1.17
If WPA encryption mode is enabled, this object indicates which encryption solutions to use for WPA clients.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tkip(1), ccmp(2), both(3)  

wsNetworkWPAKeyType 1.3.6.1.4.1.207.8.42.8.34.3.8.1.18
If WPA-SharedKey security mode is enabled, this object specifies the type of the WPA key configured. Only ascii key type is supported for this release.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ascii(1)  

wsNetworkWPAKey 1.3.6.1.4.1.207.8.42.8.34.3.8.1.19
If WPA-SharedKey security mode is enabled, this object specifies the pre-shared secret for WPA clients. For ASCII - 8-63 characters.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8..63)  

wsNetworkWPA2PreAuthenticationMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.20
If WPA2 encryption is enabled, flag to enable/disable pre-authentication support for roaming WPA2 clients.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkWPA2PreAuthenticationLimit 1.3.6.1.4.1.207.8.42.8.34.3.8.1.21
If WPA2 pre-authentication is enabled, this object specifies a limit on the number of APs within the peer group to which one client is allowed to be pre-authenticate.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..192  

wsNetworkWPA2RoambackKeyCacheHoldtime 1.3.6.1.4.1.207.8.42.8.34.3.8.1.23
Length of time in minutes a PMK will be cached by an AP after the client using this PMK has roamed away from this AP. Length of time a PMK will be cached by an AP after the PMK has been received from the WS. After this time has expired, the AP deletes the PMK entry from the security database.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..1440  

wsNetworkStaticWEPAuthenticationMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.24
Indicates security configuration for static WEP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER openSystem(1), sharedKey(2), both(3)  

wsNetworkUseWEPTransferKeyIndex 1.3.6.1.4.1.207.8.42.8.34.3.8.1.25
If wsNetSecurityMode is wepSharedKey, this object indicates which Wired Equivalent Privacy(WEP) algorithm network will use for encryption.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..4  

wsNetworkWEPKeyType 1.3.6.1.4.1.207.8.42.8.34.3.8.1.26
If WEP-SharedKey security mode is enabled, this object specifies the type WEP key configured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ascii(1), hex(2)  

wsNetworkWEPKeyLength 1.3.6.1.4.1.207.8.42.8.34.3.8.1.27
If WEP-SharedKey security mode is enabled, this object specifies number of bits for the WEP key.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sixty-four(64), one-twentyeight(128)  

wsNetworkWEPKey1 1.3.6.1.4.1.207.8.42.8.34.3.8.1.28
If WEP-SharedKey security mode is enabled, this object specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0|5..32)  

wsNetworkWEPKey2 1.3.6.1.4.1.207.8.42.8.34.3.8.1.29
If WEP-SharedKey security mode is enabled, this object specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0|5..32)  

wsNetworkWEPKey3 1.3.6.1.4.1.207.8.42.8.34.3.8.1.30
If WEP-SharedKey security mode is enabled, specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0|5..32)  

wsNetworkWEPKey4 1.3.6.1.4.1.207.8.42.8.34.3.8.1.31
If WEP-SharedKey security mode is enabled, this object specifies the key for WEP clients. Minimum characters required for key based on key type/length are: For ASCII/64 - 5 characters ASCII/128 - 13 characters HEX/64 - 10 characters HEX/128 - 26 characters
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0|5..32)  

wsClearNetworkEntry 1.3.6.1.4.1.207.8.42.8.34.3.8.1.33
This is an action object. Setting this object to enable will set Network Id configuration to default configuration. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkRedirectMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.34
Specifies the redirect mode on this network.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), http(2)  

wsNetworkRedirectURL 1.3.6.1.4.1.207.8.42.8.34.3.8.1.35
This object indicates HTTP Redirect URL on the Network Id.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..127)  

wsIfNumber 1.3.6.1.4.1.207.8.42.8.34.3.8.1.36
A unique value to identify the wireless network interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsNetworkAuthRadiusServerName 1.3.6.1.4.1.207.8.42.8.34.3.8.1.37
The name of the RADIUS server used for client authentications.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsNetworkAuthRadiusServerConfiguredStatus 1.3.6.1.4.1.207.8.42.8.34.3.8.1.38
Indicates whether the specified named RADIUS Authentication server is configured in the RADIUS Client configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-configured(1), configured(2)  

wsNetworkAcctRadiusServerName 1.3.6.1.4.1.207.8.42.8.34.3.8.1.39
The name of the RADIUS server used for reporting wireless client associations and disassociations.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsNetworkAcctRadiusServerConfiguredStatus 1.3.6.1.4.1.207.8.42.8.34.3.8.1.40
Indicates whether the specified named RADIUS Accounting server is configured in the RADIUS Client configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-configured(1), configured(2)  

wsUseNetworkRadiusConfig 1.3.6.1.4.1.207.8.42.8.34.3.8.1.41
This flag controls whether the VAP uses the network RADIUS configuration or global RADIUS configuration. When enabled, network RADIUS configuration shall be used.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkDistTunnelMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.42
Flag to enable/disable Distributed Tunneling for this Network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkBcastKeyRefreshRate 1.3.6.1.4.1.207.8.42.8.34.3.8.1.43
The 802.1x broadcastkey refresh rate command specifies the interval after which the broadcast keys are changed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..86400  

wsNetworkSessionKeyRefreshRate 1.3.6.1.4.1.207.8.42.8.34.3.8.1.44
The 802.1x SessionKey refresh rate command specifies the interval after which the Unicast session keys are changed. This is applicable only dynamic WEP and WPA Enterprise modes.Valid values are 0 and from 30-86400.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsNetworkARPSuppressionMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.45
Flag to enable/disable Wireless ARP Suppression for this Network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkBandSteerMode 1.3.6.1.4.1.207.8.42.8.34.3.8.1.46
Configure band steering on this VAP. To have band steering operationally enabled, the following conditions should be met: 1. SSIDs on both VAPs should match. 2. One radio should be in the 2.4-GHz band, and the other should be in the 5-GHz band.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wsNetworkClientQosTable 1.3.6.1.4.1.207.8.42.8.34.3.9
The following parameters can be configured for each network. This table extends the wsNetworkTable definition.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsNetworkClientQosEntry

wsNetworkClientQosEntry 1.3.6.1.4.1.207.8.42.8.34.3.9.1
Each entry in this table is associated with a unique network ID, and defines its default client QoS parameters for a managed AP. These parameters are used for any wireless client on the designated network that does not have its own comparable parameter(s) defined via RADIUS when using 802.1X authentication.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsNetworkClientQosEntry  

wsNetworkClientQosBandwidthLimitDown 1.3.6.1.4.1.207.8.42.8.34.3.9.1.1
Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client for this network, thus controlling the maximum receive rate from the AP for a wireless client. This parameter is specified in bits-per-second (bps). This object may be set to any value in the range 0-4294967295. Any configured non-zero value is rounded down to the nearest 64000 bps by the AP, but no lower than 64000. Setting this object value to 0 disables bandwidth limiting in this direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsNetworkClientQosBandwidthLimitUp 1.3.6.1.4.1.207.8.42.8.34.3.9.1.2
Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP for this network, thus controlling the maximum send rate to the AP for a wireless client. This parameter is specified in bits-per-second (bps). This object may be set to any value in the range 0-4294967295. Any configured non-zero value is rounded down to the nearest 64000 bps by the AP, but no lower than 64000. Setting this object value to 0 disables bandwidth limiting in this direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsNetworkClientQosAccessControlDownType 1.3.6.1.4.1.207.8.42.8.34.3.9.1.3
Access list type used for the wireless down (outbound) direction from AP to client for this network. Setting this object usually requires that the wsNetworkClientQosAccessControlDownName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsNetworkClientQosAccessControlDownName 1.3.6.1.4.1.207.8.42.8.34.3.9.1.4
Name of the access list to use in accordance with the wsNetworkClientQosAccessControlDownType as follows: none(1) - This object is not used and must not be set. ip(2) - This specifies an IP access list number in the range 1-199, entered as a character string rather than an integer, or an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IP access list, as defined by the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are specified here using a character string notation instead of an integer value. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosAccessControlDownType to none(0), this object must not be set. 2. When setting wsNetworkClientQosAccessControlDownType to any value other than none(0), both the wsNetworkClientQosAccessControlDownType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosAccessControlDownType value, provided the type value is anything other than none(0).
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsNetworkClientQosAccessControlUpType 1.3.6.1.4.1.207.8.42.8.34.3.9.1.5
Access list type used for the wireless up (inbound) direction from client to AP for this network. Setting this object usually requires that the wsNetworkClientQosAccessControlUpName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsNetworkClientQosAccessControlUpName 1.3.6.1.4.1.207.8.42.8.34.3.9.1.6
Name of the access list to use in accordance with the wsNetworkClientQosAccessControlUpType as follows: none(1) - This object is not used and must not be set. ip(2) - This specifies an IP access list number in the range 1-199, entered as a character string rather than an integer, or an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IP access list, as defined by the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are specified here using a character string notation instead of an integer value. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosAccessControlUpType to none(0), this object must not be set. 2. When setting wsNetworkClientQosAccessControlUpType to any value other than none(0), both the wsNetworkClientQosAccessControlUpType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosAccessControlUpType value, provided the type value is anything other than none(0).
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsNetworkClientQosDiffservPolicyDownType 1.3.6.1.4.1.207.8.42.8.34.3.9.1.7
DiffServ policy type used for the wireless down (outbound) direction from AP to client for this network. Setting this object usually requires that the wsNetworkClientQosDiffservPolicyDownName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information). Only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsNetworkClientQosDiffservPolicyDownName 1.3.6.1.4.1.207.8.42.8.34.3.9.1.8
Name of the DiffServ policy to use in accordance with the wsNetworkClientQosDiffservPolicyDownType as follows: none(1) - This object is not used and must not be set. in(2) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosDiffservPolicyDownType to none(0), this object must not be set. 2. When setting wsNetworkClientQosDiffservPolicyDownType to any value other than none(0), both the wsNetworkClientQosDiffservPolicyDownType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosDiffservPolicyDownType value, provided the type value is anything other than none(0).
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsNetworkClientQosDiffservPolicyUpType 1.3.6.1.4.1.207.8.42.8.34.3.9.1.9
DiffServ policy type used for the wireless up (inbound) direction from client to AP for this network. Setting this object usually requires that the wsNetworkClientQosDiffservPolicyUpName object also be set at the same time (see the 'Object set restrictions' in that object's description for more information). Only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsNetworkClientQosDiffservPolicyUpName 1.3.6.1.4.1.207.8.42.8.34.3.9.1.10
Name of the DiffServ policy to use in accordance with the wsNetworkClientQosDiffservPolicyUpType as follows: none(1) - This object is not used and must not be set. in(2) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation. Object set restrictions: ------------------------ 1. When setting wsNetworkClientQosDiffservPolicyUpType to none(0), this object must not be set. 2. When setting wsNetworkClientQosDiffservPolicyUpType to any value other than none(0), both the wsNetworkClientQosDiffservPolicyUpType and this object must be set at the same time (i.e. use multiple variable bindings). 3. This object may be set by itself in accordance with the existing wsNetworkClientQosDiffservPolicyUpType value, provided the type value is anything other than none(0).
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsNetworkClientQosMode 1.3.6.1.4.1.207.8.42.8.34.3.9.1.11
Flag to enable/disable AP quality-of-service for wireless clients on this network.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProfileRadioSupportedChannelsTable 1.3.6.1.4.1.207.8.42.8.34.3.10
This table represents the supported channels by AP Profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioSupportedChannelsEntry

wsAPProfileRadioSupportedChannelsEntry 1.3.6.1.4.1.207.8.42.8.34.3.10.1
Each entry in this table represents a supported channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioSupportedChannelsEntry  

wsSupportedChannel 1.3.6.1.4.1.207.8.42.8.34.3.10.1.1
Indicates a channel currently supported by the radio for use with client connections. The set of supported channel numbers is determined by country code, radio mode, and in the case of modes that are compatible with 802.11n, primary channel selection and channel bandwidth settings.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsAPProfileRadioEligibleChannelsTable 1.3.6.1.4.1.207.8.42.8.34.3.11
This table represents the channels of an AP profile that are eligible for automatic channel selection.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioEligibleChannelsEntry

wsAPProfileRadioEligibleChannelsEntry 1.3.6.1.4.1.207.8.42.8.34.3.11.1
Each entry in this table represents an eligible channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioEligibleChannelsEntry  

wsEligibleChannel 1.3.6.1.4.1.207.8.42.8.34.3.11.1.1
Indicates a channel currently eligible for automatic channel selection by the radio for use with client connections. The set of eligible channel numbers is a subset of the channels supported by the radio in its current configuration of country, mode, and in the case of modes that are compatible with 802.11n, primary channel selection and channel bandwidth settings. For 80Mhz 4 channels form a set and setting one channel would unset all the remaining channels in the set. Deleting one channel would unset all the channels in the set.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

wsEligibleChannelRowStatus 1.3.6.1.4.1.207.8.42.8.34.3.11.1.2
The eligible channel status. Supported values: active(1) - valid instance createAndGo(4) - creates a new instance destroy(6) - removes an instance
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsAPProfileRadioTspecTable 1.3.6.1.4.1.207.8.42.8.34.3.12
This table contains TSPEC parameters that can be configured within an AP Profile per radio interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioTspecEntry

wsAPProfileRadioTspecEntry 1.3.6.1.4.1.207.8.42.8.34.3.12.1
Each entry in this table represents TSPEC parameters that can be configured per radio interface within an AP profile. These entries augment the wsAPProfileRadioEntry definition for TSPEC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioTspecEntry  

wsAPRadioTspecMode 1.3.6.1.4.1.207.8.42.8.34.3.12.1.1
The overall TSPEC operational mode for this radio. This object must be set to enable(1) for any of the other TSPEC ACM configuration parameters defined in this table row to have an effect. The default value for this object is disable(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioTspecVoiceAcmMode 1.3.6.1.4.1.207.8.42.8.34.3.12.1.2
Regulates mandatory admission control for the voice access category (AC). When set to enable(1), the voice AC may only be used by WMM-compliant client stations that have successfully established a TSPEC for this AC. Note that setting the wsAPRadioTspecLegacyWmmQueueMapMode object to enable(1) overrides the exclusive use of the voice AC by allowing legacy (i.e. non-WMM-compliant) client stations to use it as well.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioTspecVideoAcmMode 1.3.6.1.4.1.207.8.42.8.34.3.12.1.3
Regulates mandatory admission control for the video access category (AC). When set to enable(1), the video AC may only be used by WMM-compliant client stations that have successfully established a TSPEC for this AC. Note that setting the wsAPRadioTspecLegacyWmmQueueMapMode object to enable(1) overrides the exclusive use of the video AC by allowing legacy (i.e. non-WMM-compliant) client stations to use it as well.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPRadioTspecVoiceAcmLimit 1.3.6.1.4.1.207.8.42.8.34.3.12.1.4
Defines the maximum amount of wireless bandwidth utilization to admit for the voice access category. TSPEC requests that would cause this limit to be exceeded are rejected. Note that this value establishes an upper limit for wireless bandwidth to be admitted for this access category but does not guarantee that this limit can be reached. Setting this object value to 0 and the wsAPRadioTspecVoiceAcmMode object to enable(1) causes all TSPEC requests to be rejected by the AP for the voice access category. The sum of this value and the wsAPRadioTspecVideoAcmLimit object value is not allowed to exceed 70. This value is treated as a percentage.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0 | 1..70  

wsAPRadioTspecVideoAcmLimit 1.3.6.1.4.1.207.8.42.8.34.3.12.1.5
Defines the maximum amount of wireless bandwidth utilization to admit for the video access category. TSPEC requests that would cause this limit to be exceeded are rejected. Note that this value establishes an upper limit for wireless bandwidth to be admitted for this access category but does not guarantee that this limit can be reached. Setting this object value to 0 and the wsAPRadioTspecVideoAcmMode object to enable(1) causes all TSPEC requests to be rejected by the AP for the video access category. The sum of this value and the wsAPRadioTspecVoiceAcmLimit object value is not allowed to exceed 70. This value is treated as a percentage.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0 | 1..70  

wsAPRadioTspecRoamReserveLimit 1.3.6.1.4.1.207.8.42.8.34.3.12.1.6
Defines the portion of the wsAPRadioTspecVoiceAcmLimit and wsAPRadioTspecVideoAcmLimit object values to hold in reserve for roaming clients only. If this value exceeds the current value in either of those two objects, respectively, then their entire ACM limit is used exclusively for roaming clients. Setting this object value to 0 causes none of the voice or video ACM limit values to be reserved for roaming clients - they compete equally with non-roaming clients for wireless network bandwidth. This value is treated as a percentage.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0 | 1..70  

wsAPRadioTspecApInactivityTimeout 1.3.6.1.4.1.207.8.42.8.34.3.12.1.7
Specifies the amount of time that an active traffic stream (TS) in the downlink direction may be idle, from the perspective of the AP, before it is deleted by the AP. For a bidirectional TS, both the wsAPRadioTspecApInactivityTimeout and the wsAPRadioTspecStaInactivityTimeout must expire in order for the TS to be deleted by the AP due to inactivity. If either of these timeouts is disabled, the AP will not delete a bidirectional TS due to inactivity. This value is specified in seconds. Setting this object value to 0 disables this timeout.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0 | 1..120  

wsAPRadioTspecStaInactivityTimeout 1.3.6.1.4.1.207.8.42.8.34.3.12.1.8
Specifies the amount of time that an active traffic stream (TS) in the uplink direction may be idle, from the perspective of the AP, before it is deleted by the AP. For a bidirectional TS, both the wsAPRadioTspecApInactivityTimeout and the wsAPRadioTspecStaInactivityTimeout must expire in order for the TS to be deleted by the AP due to inactivity. If either of these timeouts is disabled, the AP will not delete a bidirectional TS due to inactivity. This value is specified in seconds. Setting this object value to 0 disables this timeout.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0 | 1..120  

wsAPRadioTspecLegacyWmmQueueMapMode 1.3.6.1.4.1.207.8.42.8.34.3.12.1.9
When enabled, the AP allows intermixing of legacy traffic with Wi-Fi Multimedia (WMM) traffic on access category queues that are operating according to admission control mandatory (ACM) rules. This mode is intended for use with non Wi-Fi Multimedia Enabled (non-WME) clients and is disabled by default. When this object is set to enable(1), both the voice and video access categories are accessible by wireless clients that do not have an admitted TSPEC, which can lead to underestimation of the available medium time by wireless TSPEC admission control. Use caution when enabling this mode and also consider using very small ACM limit values as well.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProfileRadioMCSIndexTable 1.3.6.1.4.1.207.8.42.8.34.3.13
This table contains MCS indices that can be configured within an AP Profile per radio interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProfileRadioMCSIndexEntry

wsAPProfileRadioMCSIndexEntry 1.3.6.1.4.1.207.8.42.8.34.3.13.1
Each entry in this table represents an MCS index that can be configured per radio interface within an AP profile.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAPProfileRadioMCSIndexEntry  

wsAPRadioMCSIndexValue 1.3.6.1.4.1.207.8.42.8.34.3.13.1.1
Indicates an index value available for use with the Modulation and Coding Scheme (MCS) for 802.11n connections. Not all radios support index values from 16 to 23.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32 0..23  

wsAPRadioMCSIndexAvailable 1.3.6.1.4.1.207.8.42.8.34.3.13.1.2
Indicates that the associated index value has or has not been configured for use with the Modulation and Coding Scheme (MCS) for 802.11n connections.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wsAPCodeDownloadServerIP 1.3.6.1.4.1.207.8.42.8.34.4.1
Indicates the server IP address to use for an AP code download request.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsAPImageTypeFileTable 1.3.6.1.4.1.207.8.42.8.34.4.2
The AP image type capability table contain parameters that are configurable for each image type download.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPImageTypeFileEntry

wsAPImageTypeFileEntry 1.3.6.1.4.1.207.8.42.8.34.4.2.1
Each entry provides image type capability details for each AP image type supported by the WS.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPImageTypeFileEntry  

wsAPImageFilePath 1.3.6.1.4.1.207.8.42.8.34.4.2.1.1
Indicates the file path on the server to use for an AP code download request.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..96)  

wsAPImageFileName 1.3.6.1.4.1.207.8.42.8.34.4.2.1.2
Indicates file on the server to use for an AP code download request.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAPCodeDownloadMACAddress 1.3.6.1.4.1.207.8.42.8.34.4.3
Indicates an AP MAC address to use in a code download request for a single AP. MAC address zero indicates the code download request is for all managed APs. Setting this object initiates the code download. A read on this object always returns zero.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPCodeDownloadGroupSize 1.3.6.1.4.1.207.8.42.8.34.4.4
Indicates the number of APs the wireless controller will issue a code download request to at one time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..48  

wsAPCodeDownloadImageType 1.3.6.1.4.1.207.8.42.8.34.4.5
Indicates which image to download to the AP(s). Configurable values are: - tq3600, if download is for APs with hardware that only require tq3600 code - image2, reserved future - image3, reserved future - tq2450, if download is for APs with hardware that only require tq2450 code - tq4400, if download is for APs with hardware that only require tq4400 code - tq4600, if download is for APs with hardware that only require tq4600 code - tq3200, if download is for APs with hardware that only require tq3200 code - tq3400, if download is for APs with hardware that only require tq3400 code - all, if download involves APs that require tq3600, tq2450, tq4400, tq4600, tq3200, and tq3400 code
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tq3600(1), image2(2), image3(3), tq2450(4), tq4400(5), tq4600(6), tq3200(7), tq3400(8), all(9)  

wsAPCodeDownloadStatus 1.3.6.1.4.1.207.8.42.8.34.4.6
This indicates the current status for an AP code download request. Default value is not started.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), code-transfer-in-progress(3), aborted(4), nvram-update-in-progress(5), success(6), failure(7)  

wsAPCodeDownloadTotalCount 1.3.6.1.4.1.207.8.42.8.34.4.7
Indicates the number of WS managed APs at the time a code download request is started. Value is 1 if a download request is for single AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..48  

wsAPCodeDownloadSuccessCount 1.3.6.1.4.1.207.8.42.8.34.4.8
Indicates the total number of APs that have successfully completed code download.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

wsAPCodeDownloadFailureCount 1.3.6.1.4.1.207.8.42.8.34.4.9
Indicates the total number of APs that have failed to complete a code download.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

wsAPCodeDownloadAbortCount 1.3.6.1.4.1.207.8.42.8.34.4.10
Indicates the total number of APs aborted from the code download.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..48  

wsAPCodeDownloadAbort 1.3.6.1.4.1.207.8.42.8.34.4.11
Abort the current code download on managed AP(s). Supported values: disable(0) - Code download is not to be aborted. enable(1) - Code download is to be aborted.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

wsChannelPlanTable 1.3.6.1.4.1.207.8.42.8.34.5.1
This table displays the channel plan parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsChannelPlanEntry

wsChannelPlanEntry 1.3.6.1.4.1.207.8.42.8.34.5.1.1
Each entry in this table will indicate the channel plan parameters for specific radio frequency.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsChannelPlanEntry  

wsChannelPlan 1.3.6.1.4.1.207.8.42.8.34.5.1.1.1
This object indicates the whether the channel plan is for ieee802dot11bORgn or ieee802dot11an.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ieee802dot11an(1), ieee802dot11bORgn(2)  

wsChannelPlanMode 1.3.6.1.4.1.207.8.42.8.34.5.1.1.2
Indicates mode of computing and applying channel adjustments for managed AP radios operating in 2.4Ghz and 5Ghz band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER manual(1), interval(2), time(3)  

wsChannelPlanInterval 1.3.6.1.4.1.207.8.42.8.34.5.1.1.3
If channel plan mode is interval, this object indicates a regular interval in minutes at which to compute and apply a new channel adjustments.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 10..1440  

wsChannelPlanTime 1.3.6.1.4.1.207.8.42.8.34.5.1.1.4
If channel plan mode is time, this object indicates the next scheduled time in minutes at which to compute and apply a new channel adjustments. Zero minutes stands for mid-night.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1440  

wsChannelPlanHistoryDepth 1.3.6.1.4.1.207.8.42.8.34.5.1.1.5
Indicates the maximum number of previously applied channel algorithm iterations stored on the controller and used in the next channel adjustment computation.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..10  

wsChannelPlanOperatingStatus 1.3.6.1.4.1.207.8.42.8.34.5.1.1.6
Indicates whether or not automatic channel adjustment is operating for managed AP radios operating in 2.4Ghz and 5Ghz band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inActive(2)  

wsChannelPlanLastIterationStatus 1.3.6.1.4.1.207.8.42.8.34.5.1.1.7
Indicates the current iteration of channel plan adjustments for managed AP radio.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..10  

wsChannelPlanManualAction 1.3.6.1.4.1.207.8.42.8.34.5.1.1.8
This action object is used to: - Run the Proposed Channel Adjustment alogorithm - Abort the channel plan. - Clear the calculated 2.4Ghz and 5Ghz channel plan. Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2), abort(3), clear(4)  

wsChannelPlanManualStatus 1.3.6.1.4.1.207.8.42.8.34.5.1.1.9
Indicates the current state of a manual request to compute or apply proposed channel adjustments.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER none(1), algorithm-in-progress(2), algorithm-complete(3), apply-in-process(4), apply-complete(5)  

wsChannelPlanLastAlgorithmTime 1.3.6.1.4.1.207.8.42.8.34.5.1.1.10
The time since the last channel plan algorithm ran.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanChangeThreshold 1.3.6.1.4.1.207.8.42.8.34.5.1.1.11
The minimum signal strength (dBm) with which a neighbor must be detected on the current operational channel in order for the channel plan to consider moving away from the current channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -99..-1  

wsChannelPlanChangeThresholdAdj 1.3.6.1.4.1.207.8.42.8.34.5.1.1.20
The number of dBm by which to reduce the Channel Change Threshold for detected managed APs based on the Transmit Power of the detected managed APs.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..5  

wsChannelPlanIgnoreUnamangedAPs 1.3.6.1.4.1.207.8.42.8.34.5.1.1.12
When enabled, the channel plan does not take into account the interfering unmanaged APs. Only managed APs are used for generating the channel plan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsChannelPlanRunOnManagedApFailure 1.3.6.1.4.1.207.8.42.8.34.5.1.1.22
When this administrative parameter is enabled, the controller runs ACA algorithm after it detects that a managed AP failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsChannelPlanManagedAPFailureInterval 1.3.6.1.4.1.207.8.42.8.34.5.1.1.21
The number of seconds to wait before triggering the channel plan after a managed AP fails.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 60..600  

wsChannelPlanNumOfRadios 1.3.6.1.4.1.207.8.42.8.34.5.1.1.13
Number of radios operating in the band. This includes the radios with static channel assignment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanNumOfRadiosAnalysed 1.3.6.1.4.1.207.8.42.8.34.5.1.1.14
Indicates the number of AP radios analyzed by the channel algorithm. This includes APs that operate on static channels.This value is reset at the start of each channel plan cycle.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanNumOfRadiosScanned 1.3.6.1.4.1.207.8.42.8.34.5.1.1.15
Indicates the number of AP radios for which a Channel Plan Request has been sent by the channel algorithm.This value is reset at the start of each channel plan cycle.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanNumOfRadiosChanged 1.3.6.1.4.1.207.8.42.8.34.5.1.1.16
Indicates the number of AP radios whose operating channel changed. This includes APs whose channel is changed to the same channel as the original operating channel.This value is reset at the start of each channel plan cycle.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanNumOfRadiosChangedToOrigChannel 1.3.6.1.4.1.207.8.42.8.34.5.1.1.17
Indicates the number of AP radios that scanned the candidate channels but ended on the same channel.This value is reset at the start of each channel plan cycle.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanEstimatedTimeOfCompletion 1.3.6.1.4.1.207.8.42.8.34.5.1.1.18
The time for the estimated time of completion of the current channel plan cycle. When the channel plan is inactive the time stamp is zeroed out.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanPercentageComplete 1.3.6.1.4.1.207.8.42.8.34.5.1.1.19
During the channel plan cycle this parameter is the percentage of the AP radios that have been analyzed. When the channel plan is inactive this value is 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanHistoryTable 1.3.6.1.4.1.207.8.42.8.34.5.2
This table contains parameters related to channel plan algorithm history, each entry indicates a previously computed and applied channel adjustment for the specified iteration. The maximum number of channel adjustment iterations displayed is based on the 802.11b/g or 802.11a channel plan history depth.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsChannelPlanHistoryEntry

wsChannelPlanHistoryEntry 1.3.6.1.4.1.207.8.42.8.34.5.2.1
Each entry in this table represents channel plan history for WS managed AP radio.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsChannelPlanHistoryEntry  

wsChannelPlanHistory 1.3.6.1.4.1.207.8.42.8.34.5.2.1.1
This object indicates the whether the channel adjustment is for 2.4Ghz or 5Ghz band.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER ieee802dot11an(1), ieee802dot11bORgn(2)  

wsChannelPlanAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.5.2.1.2
The Ethernet address of the AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsChannelPlanAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.5.2.1.3
Indicates the radio interface for channel assignment.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsChannelPlanAPLocation 1.3.6.1.4.1.207.8.42.8.34.5.2.1.4
A descriptive name of the AP, usually represented by its location.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsChannelPlanAPHistoryIteration 1.3.6.1.4.1.207.8.42.8.34.5.2.1.5
This field indicates the iteration of the channel plan algorithm for this channel adjustment, the maximum history depth is configurable. This history prevents the same APs from being changed time after time.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..10  

wsChannelPlanAPChannel 1.3.6.1.4.1.207.8.42.8.34.5.2.1.6
Indicates the previously applied channel for this radio.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1 | 6 | 11  

wsChannelPlanManualProposedAdjustmentTable 1.3.6.1.4.1.207.8.42.8.34.5.3
This table contains parameters related to proposed channel plan adjustment. These parameters are applicable only when channel plan mode is manual.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsChannelPlanManualProposedAdjustmentEntry

wsChannelPlanManualProposedAdjustmentEntry 1.3.6.1.4.1.207.8.42.8.34.5.3.1
Each entry in this table represents proposed channel plan adjustment.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsChannelPlanManualProposedAdjustmentEntry  

wsChannelPlanManual 1.3.6.1.4.1.207.8.42.8.34.5.3.1.1
This object indicates the whether the channel plan is for 2.4Ghz or 5Ghz band.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER ieee802dot11an(1), ieee802dot11bORgn(2)  

wsChannelPlanManualMacAddress 1.3.6.1.4.1.207.8.42.8.34.5.3.1.2
The Ethernet address of the AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsChannelPlanManualAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.5.3.1.3
Indicates the radio interface for channel assignment.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsChannelPlanManualCurrentChannel 1.3.6.1.4.1.207.8.42.8.34.5.3.1.4
Indicates the current operating channel for this radio.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..13 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wsChannelPlanManualNewChannel 1.3.6.1.4.1.207.8.42.8.34.5.3.1.5
Indicates new channel assignment for this radio.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..13 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wsPowerAdjustmentMode 1.3.6.1.4.1.207.8.42.8.34.5.4
Flag to set automatic power adjustment for all managed AP radios. If power adjustment mode is interval, periodically calculate the power adjustments and apply them. However, if power adjustment is manual, calculation and assignment of power adjustments initiated and controlled by the administrator user interface commands.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER manual(1), interval(2)  

wsPowerAdjustmentStrength 1.3.6.1.4.1.207.8.42.8.34.5.5
Power Plan signal strength threshold in dBm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -99..-1  

wsPowerManualProposedAdjustmentAction 1.3.6.1.4.1.207.8.42.8.34.5.6
This action object is used to: - Run the Proposed Power Adjustment alogorithm - Apply the same to network. - Clear the calculated power plan. Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2), apply(3), clear(4)  

wsManualPowerAdjustmentStatus 1.3.6.1.4.1.207.8.42.8.34.5.7
Indicates the current state of a manual request to compute or apply proposed power adjustments.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER none(1), algorithm-in-progress(2), algorithm-complete(3), apply-in-process(4), apply-complete(5)  

wsPowerManualProposedAdjustmentTable 1.3.6.1.4.1.207.8.42.8.34.5.8
This table represents the proposed power adjustment status parameters. These parameters are displayed only when power adjustment mode is set to manual. The administrator manually apply all of the proposed power adjustments displayed.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsPowerManualProposedAdjustmentEntry

wsPowerManualProposedAdjustmentEntry 1.3.6.1.4.1.207.8.42.8.34.5.8.1
Each entry in this table represents the proposed power adjustment status parameters.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsPowerManualProposedAdjustmentEntry  

wsPowerManualProposedAdjustmentAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.5.8.1.1
The Ethernet address of the AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsPowerManualProposedAdjustmentAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.5.8.1.2
Indicates the radio interface for power assignment.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsPowerManualProposedAdjustmentAPCurrentTxPower 1.3.6.1.4.1.207.8.42.8.34.5.8.1.3
Indicates the current operating power for this radio from the last power plan computation. Even after the new power plan is applied, this object displays the old value as opposed to the actual power currently set into the radio.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

wsPowerManualProposedAdjustmentAPNewTxPower 1.3.6.1.4.1.207.8.42.8.34.5.8.1.4
Indicates the new proposed power assignment for this radio.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

wsPowerPlanOperatingStatus 1.3.6.1.4.1.207.8.42.8.34.5.9
The Operational Status of the Power Plan Algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), gatheringNbrData(1), changingPower(2), powerPlanComplete(3)  

wsPowerPlanAvgNumInterferingAPs 1.3.6.1.4.1.207.8.42.8.34.5.10
The average number of managed radios detected by every operational mode radio in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanAvgNumInterferingVAPs 1.3.6.1.4.1.207.8.42.8.34.5.11
The average number of managed virtual APs detected by every operational mode radio in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanAPNumOpRadios 1.3.6.1.4.1.207.8.42.8.34.5.12
The number of operational mode radios in the cluster. The sentry and disabled radios are not counted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanAPNumPwrCycles 1.3.6.1.4.1.207.8.42.8.34.5.13
Number of power plan cycles executed by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanGlobalNumPwrChanges 1.3.6.1.4.1.207.8.42.8.34.5.14
Number of transmit power changes done by the power plan algorithm for all radios in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanGlobalNumPwrInc 1.3.6.1.4.1.207.8.42.8.34.5.15
Number of transmit power increases done by the power plan algorithm for all radios in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanGlobalNumPwrDec 1.3.6.1.4.1.207.8.42.8.34.5.16
Number of transmit power reductions done by the power plan algorithm for all radios in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanTimeSinceLastPowerPLan 1.3.6.1.4.1.207.8.42.8.34.5.17
Time since the last power plan was done. The power plan could have been triggered manually or automatically.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanPerRadioPerBandTable 1.3.6.1.4.1.207.8.42.8.34.5.18
This table contains the per band per radio channel plan status for a Managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsChannelPlanPerRadioPerBandEntry

wsChannelPlanPerRadioPerBandEntry 1.3.6.1.4.1.207.8.42.8.34.5.18.1
Each entry in this table represents channel plan per band per radio status for WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsChannelPlanPerRadioPerBandEntry  

wsChannelPlanType 1.3.6.1.4.1.207.8.42.8.34.5.18.1.1
This object indicates the whether the channel plan is for ieee802dot11bORgn or ieee802dot11an.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER ieee802dot11an(1), ieee802dot11bORgn(2)  

wsChannelPlanAPMacAddr 1.3.6.1.4.1.207.8.42.8.34.5.18.1.2
The Ethernet address of the Managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsChannelPlanAPRadioIntf 1.3.6.1.4.1.207.8.42.8.34.5.18.1.3
Indicates the radio interface for channel assignment.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsChannelPlanAPIsLocal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.4
Flag Indicating whether the AP is managed by the cluster controller or a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER peerSwitch(0), local(1)  

wsChannelPlanAPCurrentChannel 1.3.6.1.4.1.207.8.42.8.34.5.18.1.5
Indicates the current operating channel for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanAPOldChannel 1.3.6.1.4.1.207.8.42.8.34.5.18.1.6
Channel on which this radio was operating before the channel change algorithm changed its channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsChannelPlanAPStrongestOldSignal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.7
The strongest signal detected on the old channel. This is the signal used in the channel selection decision.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPStrongestNewSignal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.8
The strongest signal detected on the new channel during the channel validation scan. This is the signal used in the channel selection decision. If the algorithm does not change the channel then this is the signal on the current channel detected during the channel check scan.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPChannelChangeInd 1.3.6.1.4.1.207.8.42.8.34.5.18.1.9
Flag indicating whether the last channel plan cycle changed the channel for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(0), yes(1), wait(2)  

wsChannelPlanAPReasonCode 1.3.6.1.4.1.207.8.42.8.34.5.18.1.10
The reason code indicating why the channel was changed or not changed for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER chanPlanNeverExecuted(0), channelIsStatic(1), oneEligibleChannel(2), detectedAPSignalBelowThresh(3), chanFoundWithLowInterference(4), chanNotFoundWithLowInterference(5), partOfWDSLink(6)  

wsChannelPlanAPStrongestOldManagedAPandSignal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.11
The MAC address and the signal strength of the strongest managed neighbor AP detected on the channel before that channel was changed. The MAC address is the base MAC of the managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPStrongestNewManagedAPandSignal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.12
The MAC address and the signal strength of the strongest managed neighbor AP detected on the current operating channel. The MAC address is the base MAC of the managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPStrongestOldUnmanagedAPandSignal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.13
The MAC address and the signal strength of the strongest unmanaged neighbor AP detected on the channel before that channel was changed.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPStrongestNewUnmanagedAPandSignal 1.3.6.1.4.1.207.8.42.8.34.5.18.1.14
The MAC address and the signal strength of the strongest unmanaged neighbor AP detected on the current operating channel.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPTimeSinceLastChannelChange 1.3.6.1.4.1.207.8.42.8.34.5.18.1.15
The UTC time since the channel was last changed by the channel plan algorithm..
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsChannelPlanAPLastChanScanDuration 1.3.6.1.4.1.207.8.42.8.34.5.18.1.16
Number of milliseconds that the AP spent scanning channels during the last channel plan cycle. The scan time includes the operational channel scan, so the time may be non-zero even when the radio did not change channels.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999999  

wsPowerPlanPerRadioTable 1.3.6.1.4.1.207.8.42.8.34.5.19
This table contains the per radio Power Plan Status for a Managed AP .
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsPowerPlanPerRadioEntry

wsPowerPlanPerRadioEntry 1.3.6.1.4.1.207.8.42.8.34.5.19.1
Each entry in this table represents the per radio power plan status for WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsPowerPlanPerRadioEntry  

wsPowerPlanAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.5.19.1.1
The Ethernet address of the Managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsPowerPlanAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.5.19.1.2
Indicates the radio interface of the Managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsPowerPlanAPIsLocal 1.3.6.1.4.1.207.8.42.8.34.5.19.1.3
Flag Indicating whether the AP is managed by the cluster controller or a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER peerSwitch(0), local(1)  

wsPowerPlanAPChannel 1.3.6.1.4.1.207.8.42.8.34.5.19.1.4
Channel on which the radio is operating. For sentry radios this field is set to sentry. The disabled radios report None.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsPowerPlanAPTxPower 1.3.6.1.4.1.207.8.42.8.34.5.19.1.5
The current operating power for this radio. Sentry radios and disabled radios report 0%.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsPowerPlanAPNumInterferingAPs 1.3.6.1.4.1.207.8.42.8.34.5.19.1.6
The number of APs managed by this cluster detected by this radio on the operational channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanAPNumInterferingVAPs 1.3.6.1.4.1.207.8.42.8.34.5.19.1.7
The number of VAPs managed by this cluster detected by this radio on the operational channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanAPStrongestDetectorAP 1.3.6.1.4.1.207.8.42.8.34.5.19.1.8
The base MAC address of the managed AP that detects this radio with the strongest signal.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsPowerPlanAPStrongestDetectorRadio 1.3.6.1.4.1.207.8.42.8.34.5.19.1.9
The radio number of the managed AP that detects this radio with the strongest signal.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanAPStrongestDetectorSignal 1.3.6.1.4.1.207.8.42.8.34.5.19.1.10
The strongest signal strength in dBm with which a managed neighbor detects this radio.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsPowerPlanAPStrongestDetectedNeighbor 1.3.6.1.4.1.207.8.42.8.34.5.19.1.11
The MAC address of the AP that this radio detects with the strongest signal.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsPowerPlanAPStrongestDetectedSignal 1.3.6.1.4.1.207.8.42.8.34.5.19.1.12
The signal strength with which this radio detects the strongest neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsPowerPlanAPLastPwrAdjStatus 1.3.6.1.4.1.207.8.42.8.34.5.19.1.13
The status indicating whether the power was changed during the most recent cycle of the power adjustment algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unchanged(0), increased(1), reduced(2)  

wsPowerPlanAPLastPwrAdjReasonCode 1.3.6.1.4.1.207.8.42.8.34.5.19.1.14
The reason code indicating why the last power adjustment action was taken or not taken.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER powerPlanNeverExecuted(0), powerPlanRadioInSentryMode(1), powerPlanRadioAutoPowerDisable(2), powerPlanRadioPowerUnchanged(3), powerPlanRadioOperatingInMaxPower(4), powerPlanRadioOperatingInMinPower(5), powerPlanRadioMinPowerIs100(6), powerPlanRadioPowerIncreaseRequired(7), powerPlanRadioPowerDecreaseRequired(8), powerPlanRadioPowerAdjNone(9), powerPlanRadioPowerPartOfWDSLink(10)  

wsPowerPlanAPNumPwrChanges 1.3.6.1.4.1.207.8.42.8.34.5.19.1.15
Number of transmit power changes done by the power plan algorithm for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanAPNumPwrInc 1.3.6.1.4.1.207.8.42.8.34.5.19.1.16
Number of transmit power increases done by the power plan algorithm for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanAPNumPwrDec 1.3.6.1.4.1.207.8.42.8.34.5.19.1.17
Number of transmit power reductions done by the power plan algorithm for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanPerProfileTable 1.3.6.1.4.1.207.8.42.8.34.5.20
This table contains the per profile power plan status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsPowerPlanPerProfileEntry

wsPowerPlanPerProfileEntry 1.3.6.1.4.1.207.8.42.8.34.5.20.1
Each entry in this table represents the per profile power plan status.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsPowerPlanPerProfileEntry  

wsPowerPlanProfileId 1.3.6.1.4.1.207.8.42.8.34.5.20.1.1
Indicates the profile Id.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanPerProfileAvgNumInterferingAPs 1.3.6.1.4.1.207.8.42.8.34.5.20.1.2
The average number of managed radios detected by every operational mode radio that uses this profile. If the number of APs is greater than 999 then it is reported as 999..
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanPerProfileAvgNumInterferingVAPs 1.3.6.1.4.1.207.8.42.8.34.5.20.1.3
The average number of managed virtual APs detected by every operational mode radio that uses this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..999  

wsPowerPlanNumPwrChanges 1.3.6.1.4.1.207.8.42.8.34.5.20.1.4
Number of transmit power changes done by the power plan algorithm for all radios in this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanNumPwrInc 1.3.6.1.4.1.207.8.42.8.34.5.20.1.5
Number of transmit power increases done by the power plan algorithm for all radios in this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPowerPlanNumPwrDec 1.3.6.1.4.1.207.8.42.8.34.5.20.1.6
Number of transmit power reductions done by the power plan algorithm for all radios in this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsNtwProvisoningAction 1.3.6.1.4.1.207.8.42.8.34.5.21
This action object is used to: - start the network provision. - stop the network provision.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), start(1), stop(2)  

wsNtwProvisioningOperatingStatus 1.3.6.1.4.1.207.8.42.8.34.5.22
The Operational Status of the Initial Network Provisioning Protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notstarted(0), running(1), finished(2), aborted(3), failed(4)  

wsNtwProvisioningTimeStamp 1.3.6.1.4.1.207.8.42.8.34.5.23
Number of seconds the latest invocation of the protocol has been running.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsNtwProvisioningChanBGCompletion 1.3.6.1.4.1.207.8.42.8.34.5.24
Percent complete for the channel protocol in the 2.4 GHz band.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsNtwProvisioningChanACompletion 1.3.6.1.4.1.207.8.42.8.34.5.25
Percent complete for the channel protocol in the 5GHz band.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsNtwProvisioningPowerPlanCnt 1.3.6.1.4.1.207.8.42.8.34.5.26
Count-Down of how many power plan interations remain to be done.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..5  

wsManagedAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.6.1
This table contains status parameters for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPStatusEntry

wsManagedAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.6.1.1
Each entry in this table contains status parameters for an AP managed by the controller. Controller can managed up to 48 APs at a time, with the actual maximum number supported dependent on the CPU performance of the controller and may be smaller or larger for some implementations.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPStatusEntry  

wsManagedAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.6.1.1.1
Ethernet address of the WS managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsManagedAPIpAddress 1.3.6.1.4.1.207.8.42.8.34.6.1.1.2
Network IP address of the managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsManagedAPVendorId 1.3.6.1.4.1.207.8.42.8.34.6.1.1.3
Indicates vendor of the WS managed AP software. Broadcom vendor ID is 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

wsManagedAPSoftwareVersion 1.3.6.1.4.1.207.8.42.8.34.6.1.1.4
Indicates software version of the WS managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsManagedAPHWType 1.3.6.1.4.1.207.8.42.8.34.6.1.1.5
Indicates hardware platform of the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

wsManagedAPSerialNumber 1.3.6.1.4.1.207.8.42.8.34.6.1.1.6
Indicates serial number of the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsManagedAPPartNumber 1.3.6.1.4.1.207.8.42.8.34.6.1.1.7
Indicates hardware part number of the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsManagedAPDiscoveryReason 1.3.6.1.4.1.207.8.42.8.34.6.1.1.8
Indicates discovery method used to detect the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ip-poll(1), peer-switch-initiated(2), switch-ip-configured-in-ap(3), switch-ip-obtained-via-dhcp(4), l2Discovery(5)  

wsManagedAPStatus 1.3.6.1.4.1.207.8.42.8.34.6.1.1.9
Indicates current state of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discovered(1), authenticated(2), upgrading(3), managed(4), connection-failed(5), deleted(6)  

wsManagedAPAuthenticatedClients 1.3.6.1.4.1.207.8.42.8.34.6.1.1.10
Indicates total number of clients currently authenticated to an AP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPSysUpTime 1.3.6.1.4.1.207.8.42.8.34.6.1.1.11
Indicates time in seconds since last power-on reset.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsManagedAPProfileId 1.3.6.1.4.1.207.8.42.8.34.6.1.1.12
The configuration profile currently applied to the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

wsManagedAPProfileName 1.3.6.1.4.1.207.8.42.8.34.6.1.1.13
The descriptive name for the profile currently applied to the AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsManagedAPProtocolVersion 1.3.6.1.4.1.207.8.42.8.34.6.1.1.14
Indicates the protocol version supported by the software on the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

wsManagedAPCodeDownloadStatus 1.3.6.1.4.1.207.8.42.8.34.6.1.1.15
This indicates the current status of a code download request for this AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), code-transfer-in-progress(3), waiting-for-aps-to-download(4), aborted(5), nvram-update-in-progress(6), timed-out(7), failure(8)  

wsManagedAPLocation 1.3.6.1.4.1.207.8.42.8.34.6.1.1.16
A descriptive name for the AP, usually represented by location.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsManagedAPLastFailingConfigElement 1.3.6.1.4.1.207.8.42.8.34.6.1.1.17
Indicates the element Id of the last failing configuration element.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

wsManagedAPConfigFailureErrMsg 1.3.6.1.4.1.207.8.42.8.34.6.1.1.18
Indicates an ASCII string filled in by the AP, containing the error message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

wsManagedAPReset 1.3.6.1.4.1.207.8.42.8.34.6.1.1.19
This is an action object. Setting this object to enable will reset the AP. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsManagedAPResetStatus 1.3.6.1.4.1.207.8.42.8.34.6.1.1.20
This object gives status regarding the AP that got reset.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-started(1), in-progress(2), success(3), failure(4)  

wsManagedAPFailedEntryPurge 1.3.6.1.4.1.207.8.42.8.34.6.1.1.21
This is an action object. Setting this object to enable will purge the failed AP entry. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsManagedAPDebugPassword 1.3.6.1.4.1.207.8.42.8.34.6.1.1.22
Indicates password to be used for debugging managed AP. User should enable debug mode to set debug password. If password is configured, read on this object will return '*****'.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsManagedAPDebugMode 1.3.6.1.4.1.207.8.42.8.34.6.1.1.23
This is an action object. Enabling this object will enable the telnet access to the managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsManagedAPDebugStatus 1.3.6.1.4.1.207.8.42.8.34.6.1.1.24
This object indicates the status of the debug action requested when managed AP debug mode is set.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), in-progress(3), success(4), failure(5)  

wsManagedAPAge 1.3.6.1.4.1.207.8.42.8.34.6.1.1.25
Time since last communication with an AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsManagedAPManagingSwitch 1.3.6.1.4.1.207.8.42.8.34.6.1.1.26
This object indicates whether the AP is managed by this controller or peer-controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local-switch(1), peer-switch(2)  

wsManagedAPSwitchMacAddress 1.3.6.1.4.1.207.8.42.8.34.6.1.1.27
MAC address of the WS managing the AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsManagedAPSwitchIpAddress 1.3.6.1.4.1.207.8.42.8.34.6.1.1.28
IP address of the WS managing the AP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsManagedAPIpMask 1.3.6.1.4.1.207.8.42.8.34.6.1.1.29
Network IP mask of the managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsManagedAPDistTunnelHomeAPClients 1.3.6.1.4.1.207.8.42.8.34.6.1.1.30
Number of clients using this AP as a Home AP. It is also the number of clients that roamed away from this AP and are tunneling data back to it.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelAssocAPClients 1.3.6.1.4.1.207.8.42.8.34.6.1.1.31
Number of clients using this AP as an association AP. It is also the number of clients that roamed to this AP and are tunneling data back to the Home AP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelsTotal 1.3.6.1.4.1.207.8.42.8.34.6.1.1.32
Total number of APs to which this AP establishes distributed tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelsMaxMcastRepl 1.3.6.1.4.1.207.8.42.8.34.6.1.1.33
Maximum number of tunnels on the home AP that are members of the same VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelsMaxVlanMcastRepl 1.3.6.1.4.1.207.8.42.8.34.6.1.1.34
The VLAN ID over which the max number of multicast replications are sent into the distributed tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPFailedEntriesPurge 1.3.6.1.4.1.207.8.42.8.34.6.2
This is an action object. Setting this object to enable will purge all the managed AP failed entries. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsManagedAPStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.6.3
This table contains statistics available for each AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPStatisticsEntry

wsManagedAPStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.6.3.1
Each entry in this table contain statistics available for each AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPStatisticsEntry  

wsManagedAPWLANPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.1
Total packets received by an AP on the wireless network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.2
Total bytes received by an AP on the wireless network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.3
Total packets transmitted by an AP on the wireless network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.4
Total bytes transmitted by an AP on the wireless network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.5
Total packets received by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.6
Total bytes received by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetMcastPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.7
Total multicast packets received by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.8
Total packets transmitted by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.9
Total bytes transmitted by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetTransmitErrorCount 1.3.6.1.4.1.207.8.42.8.34.6.3.1.10
Total transmit errors detected by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPEthernetRecvdErrorCount 1.3.6.1.4.1.207.8.42.8.34.6.3.1.11
Total receive errors detected by an AP on the wired network.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPCL2TunnelBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.12
Total bytes received via central L2 tunnel by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPCL2TunnelPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.13
Total packets received via central L2 tunnel by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPCL2TunnelMcastRecvd 1.3.6.1.4.1.207.8.42.8.34.6.3.1.14
Total multicast packets received via central L2 tunnel by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPCL2TunnelBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.15
Total bytes transmitted via central L2 tunnel by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPCL2TunnelPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.16
Total packets transmitted via central L2 tunnel by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPCL2TunnelMcastTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.17
Total multicast packets transmitted via central L2 tunnel by the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.6.3.1.18
Total packets dropped in the receive direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.6.3.1.19
Total bytes dropped in the receive direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.6.3.1.20
Total packets dropped in the transmit direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPWLANBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.6.3.1.21
Total bytes dropped in the transmit direction by an AP on the wireless network. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.22
Total Bytes transmitted by the AP through all the established Distributed Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelBytesReceived 1.3.6.1.4.1.207.8.42.8.34.6.3.1.23
Total Bytes received by the AP through all the established Distributed Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelPacketsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.24
Total packets transmitted by the AP through all the established Distributed Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelPacketsReceived 1.3.6.1.4.1.207.8.42.8.34.6.3.1.25
Total packets received by the AP through all the established Distributed Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelMcastPacketsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.3.1.26
Total multicast packets transmitted by the AP through all the established Distributed Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelMcastPacketsReceived 1.3.6.1.4.1.207.8.42.8.34.6.3.1.27
Total multicast packets received by the AP through all the established Distributed Tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPDistTunnelRoamedClients 1.3.6.1.4.1.207.8.42.8.34.6.3.1.28
Total number of clients that used this AP for Distributed Tunneling. This inclides clients that roamed away from and to this AP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelRoamedClientsIdleTimedOut 1.3.6.1.4.1.207.8.42.8.34.6.3.1.29
Number of client tunnel sessions that were terminated because of not sending the traffic through the tunnel after roaming.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelRoamedClientsAgeTimedOut 1.3.6.1.4.1.207.8.42.8.34.6.3.1.30
Number of client tunnel sessions that were terminated because of expiry of the tunnel session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelMaxClientLimitSetupDenials 1.3.6.1.4.1.207.8.42.8.34.6.3.1.31
Number of client tunnel session setup denials by the AP because of reaching the maximum configured client limit.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPDistTunnelMaxReplSetupDenials 1.3.6.1.4.1.207.8.42.8.34.6.3.1.32
Number of client tunnel setup denials by the AP because of reaching the maximum configured VLAN replications limit.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPARPReqsFromBcastToUcast 1.3.6.1.4.1.207.8.42.8.34.6.3.1.33
Total number of ARP requests converted from broadcast to unicast packet before transmitting on wireless network.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPFilteredARPRequest 1.3.6.1.4.1.207.8.42.8.34.6.3.1.34
Total number of ARP requests filtered by the wireless ARP suppression logic.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPBroadcastedARPRequests 1.3.6.1.4.1.207.8.42.8.34.6.3.1.35
Total number of ARP requests broadcasted on to the wireless network after being processed by wireless ARP suppression logic.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioStatusTable 1.3.6.1.4.1.207.8.42.8.34.6.4
This table contains status parameters per radio interface for all the APs managed by controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPRadioStatusEntry

wsManagedAPRadioStatusEntry 1.3.6.1.4.1.207.8.42.8.34.6.4.1
Each entry in this table contains status parameters per radio interface for an AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPRadioStatusEntry  

wsManagedAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.6.4.1.1
The physical radio interface on the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsManagedAPRadioMacAddress 1.3.6.1.4.1.207.8.42.8.34.6.4.1.2
The MAC address of the physical radio.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsManagedAPRadioChannel 1.3.6.1.4.1.207.8.42.8.34.6.4.1.3
If the radio is operational, the current transmit channel for this radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..13 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wsManagedAPRadioTxPower 1.3.6.1.4.1.207.8.42.8.34.6.4.1.4
If the radio is operational, the current transmit power of the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsManagedAPRadioAuthenticatedClients 1.3.6.1.4.1.207.8.42.8.34.6.4.1.5
Total count of clients authenticated on the physical radio.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioWLANUtilization 1.3.6.1.4.1.207.8.42.8.34.6.4.1.6
Total network utilization for the physical radio. This value is based on radio statistics.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsManagedAPRadioFixedChannelIndicator 1.3.6.1.4.1.207.8.42.8.34.6.4.1.7
This flag indicates if a fixed channel is configured and assigned to the radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsManagedAPRadioMCAStatus 1.3.6.1.4.1.207.8.42.8.34.6.4.1.8
Indicates the current state of a manual request to change the channel on this radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), in-progress(2), complete(3), failure(4)  

wsManagedAPRadioFixedPowerIndicator 1.3.6.1.4.1.207.8.42.8.34.6.4.1.9
This flag indicates if a fixed power setting is configured and assigned to the radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsManagedAPRadioMPAStatus 1.3.6.1.4.1.207.8.42.8.34.6.4.1.10
Indicates the current state of a manual request to change the power setting on this radio.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), in-progress(2), complete(3), failure(4)  

wsManagedAPRadioNeighborCount 1.3.6.1.4.1.207.8.42.8.34.6.4.1.11
Total number of neighbors that can be seen by this radio in its RF area.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioFixedChannelAction 1.3.6.1.4.1.207.8.42.8.34.6.4.1.12
This is an action object. When we set this object to apply, along with wsManagedAPRadioFixedChannel, controller starts applying fixed channel assignment for this radio. Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), apply(2)  

wsManagedAPRadioFixedChannel 1.3.6.1.4.1.207.8.42.8.34.6.4.1.13
This object is used to assign the fixed channel for this radio on this Managed AP. The following MIB objects get changed on successful setting of this MIB object - 1. wsManagedAPRadioChannel --> changes to the channel set here 2. wsManagedAPRadioFixedChannelIndicator --> changes to 'yes (2)' Read on this object will always return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..13 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wsManagedAPRadioFixedPowerAction 1.3.6.1.4.1.207.8.42.8.34.6.4.1.14
This is an action object. When we set this object to apply, controller starts applying fixed power adjustment for this radio. Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), apply(2)  

wsManagedAPRadioFixedPower 1.3.6.1.4.1.207.8.42.8.34.6.4.1.15
This object is used to assign the fixed power for this radio on this Managed AP. The following MIB objects get changed on successful setting of this MIB object - 1. wsManagedAPRadioTxPower --> changes to the power set here 2. wsManagedAPRadioFixedPowerIndicator --> changes to 'yes (2)' Read on this object will always return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..100  

wsManagedAPRadioBandwidth 1.3.6.1.4.1.207.8.42.8.34.6.4.1.16
Current Channel Bandwidth In Use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), twentyMHz(1), fortyMHz(2), eightyMHz(3)  

wsManagedAPRadioResourceMeasEnabled 1.3.6.1.4.1.207.8.42.8.34.6.4.1.17
Current state of enablement for Radio Resource Management (RRM).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wsManagedAPRadioStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.6.5
This table contains statistics available for each physical radio on an AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPRadioStatisticsEntry

wsManagedAPRadioStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.6.5.1
Each entry in this table contain statistics available for each physical radio on an AP managed by controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPRadioStatisticsEntry  

wsManagedAPRadioWLANPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.6.5.1.1
Total packets received by an AP on this radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioWLANBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.6.5.1.2
Total bytes received by an AP on this radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioWLANPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.5.1.3
Total packets transmitted by an AP on this radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioWLANBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.5.1.4
Total bytes transmitted by an AP on this radio interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioTxFragmentCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.5
Count of acknowledged MPDU with an individual address or an MPDU with a multicast address of type data or management.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioMcastTxFrameCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.6
Count of successfully transmitted MSDU frames where the multicast bit is set in the destination MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioFailedCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.7
Number of times a MSDU is not transmitted successfully due to transmit attempts exceeding either the short retry limit or the long retry limit.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioRetryCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.8
Number of times a MSDU is successfully transmitted after one or more retries.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioMultipleRetryCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.9
Number of times a MSDU is successfully transmitted after more than one retry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioFrameDuplicateCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.10
Number of times a frame is received and sequence control field indicates is a duplicate.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioRTSSuccessCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.11
Count of CTS frames received in response to the RTS frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioRTSFailureCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.12
Count of CTS frames not received in response to the RTS frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioACKFailureCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.13
Count of ACK frames not received when expected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioRecvdFragmentCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.14
Count of successfully received MPDU frames of type data or management.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioMcastRecvdFrameCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.15
Count of MSDU frames received with the multicast bit set in the destination MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioFCSErrorCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.16
Count of FCS errors detected in a received MPDU frame.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioTxFrameCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.17
Count of each successfully transmitted MSDU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioWEPUndecryptableCount 1.3.6.1.4.1.207.8.42.8.34.6.5.1.18
Count of encrypted frames received and the key configuration of the transmitter indicates that the frame should not have been encrypted or that frame was discarded due to the receiving station not implementing the privacy option.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioWLANPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.6.5.1.19
Total packets dropped in the receive direction on this radio interface. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioWLANBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.6.5.1.20
Total bytes dropped in the receive direction on this radio interface. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioWLANPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.6.5.1.21
Total packets dropped in the transmit direction by this radio interface. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioWLANBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.6.5.1.22
Total bytes dropped in the transmit direction by this radio interface. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPNeighborAPListTable 1.3.6.1.4.1.207.8.42.8.34.6.6
This table contains neighbor AP list.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPNeighborAPListEntry

wsManagedAPNeighborAPListEntry 1.3.6.1.4.1.207.8.42.8.34.6.6.1
Each entry in this table contains neighbor AP information.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPNeighborAPListEntry  

wsNeighborMacAddress 1.3.6.1.4.1.207.8.42.8.34.6.6.1.1
The MAC address of neighbor AP network. This could be a physical radio MAC or VAP MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsNeighborSSID 1.3.6.1.4.1.207.8.42.8.34.6.6.1.2
Service Set ID of neighbor AP network.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsNeighborRSSI 1.3.6.1.4.1.207.8.42.8.34.6.6.1.3
This object indicates Received Signal Strength(RSSI) from the neighbor radios in a given channel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsNeighborStatus 1.3.6.1.4.1.207.8.42.8.34.6.6.1.4
Indicates managed status of the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER managed(1), unknown(2), standalone(3), rogue(4)  

wsNeighborAge 1.3.6.1.4.1.207.8.42.8.34.6.6.1.5
Indicates time since this AP was last detected.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsManagedAPNeighborEntriesPurge 1.3.6.1.4.1.207.8.42.8.34.6.7
This is an action object used to purge the AP neighbor entries. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsManagedAPNeighborClientListTable 1.3.6.1.4.1.207.8.42.8.34.6.8
This table contains neighbor client list currently detected by an RF scan on the radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPNeighborClientListEntry

wsManagedAPNeighborClientListEntry 1.3.6.1.4.1.207.8.42.8.34.6.8.1
Each entry in this table contain neighbor client information.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPNeighborClientListEntry  

wsNeighborClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.6.8.1.1
The MAC address of neighbor client station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsNeighborClientRSSI 1.3.6.1.4.1.207.8.42.8.34.6.8.1.2
Indicates RSSI from neighbor clients on the radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsNeighborClientChannel 1.3.6.1.4.1.207.8.42.8.34.6.8.1.3
Indicates AP channel, on which the client frame was received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..13 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wsNeighborClientAge 1.3.6.1.4.1.207.8.42.8.34.6.8.1.4
Indicates time since a client was last detected.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsNeighborClientDiscoveryReason 1.3.6.1.4.1.207.8.42.8.34.6.8.1.5
Indicates discovery methods for the neighbor client.
Status: current Access: read-only
OBJECT-TYPE    
  BITS none(0), rfscan-discovered(1), neighbor-ap-associated(2), current-ap-associated(3), probe-request-discovered(4), peer-ap-associated(5), ad-hoc-rogue(6)  

wsManagedAPVAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.6.9
This table contains status parameters for each VAP configured on a radio interface for a WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPVAPStatusEntry

wsManagedAPVAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.6.9.1
Each entry in this table contains status parameters of each VAP configured on radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPVAPStatusEntry  

wsManagedVAPId 1.3.6.1.4.1.207.8.42.8.34.6.9.1.1
Indicates VAP Id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

wsManagedVAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.6.9.1.2
Indicates the ethernet address of the VAP MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsManagedVAPSSID 1.3.6.1.4.1.207.8.42.8.34.6.9.1.3
Network assigned to a VAP MAC Address.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsManagedVAPAuthenticatedClients 1.3.6.1.4.1.207.8.42.8.34.6.9.1.4
Number of clients currently authenticated to VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.6.10
This table contains statistics available for each VAP on the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPVAPStatisticsEntry

wsManagedAPVAPStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.6.10.1
Each entry in this table contain statistics available for each VAP on the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPVAPStatisticsEntry  

wsManagedVAPAssociationFailures 1.3.6.1.4.1.207.8.42.8.34.6.10.1.1
Number of clients that have been denied association to the VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedVAPAuthenticationFailures 1.3.6.1.4.1.207.8.42.8.34.6.10.1.2
Number of clients that have failed authentication to the VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsManagedVAPWLANPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.6.10.1.3
Total packets received by an AP on this VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.6.10.1.4
Total bytes received by an AP on this VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.10.1.5
Total packets transmitted by an AP on this VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.6.10.1.6
Total bytes transmitted by an AP on this VAP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.6.10.1.7
Total packets dropped in the receive direction by an AP on this VAP. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.6.10.1.8
Total bytes dropped in the receive direction by an AP on this VAP. This is due to client QoS actions affecting the wireless up (inbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.6.10.1.9
Total packets dropped in the transmit direction by an AP on this VAP. This is due to client QoS actions affecting the wireless down (outbound) direction from client to AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedVAPWLANBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.6.10.1.10
Total bytes dropped in the transmit direction by an AP on this VAP. This is due to client QoS actions affecting the wireless down (outbound) direction from client to AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPResetAll 1.3.6.1.4.1.207.8.42.8.34.6.11
This is an action object. Setting this object to enable will reset all the managed APs. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsManagedAPRadioEligibleChannelListTable 1.3.6.1.4.1.207.8.42.8.34.6.12
This table represents eligible channel entries for an AP radio to consider for channel algorithm. It is based on country code, hardware capabilities and any configured channel limitations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPRadioEligibleChannelListEntry

wsManagedAPRadioEligibleChannelListEntry 1.3.6.1.4.1.207.8.42.8.34.6.12.1
Each entry in this table represents eligible channel for an AP radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPRadioEligibleChannelListEntry  

wsManagedAPRadioEligibleChannel 1.3.6.1.4.1.207.8.42.8.34.6.12.1.1
Indicates list of supported channel by the managed ap. List contains one or more entries from 1-255, actual range is determined by physical mode and country code.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..64  

wsManagedAPRadioEligibleChannelRdrDetRequired 1.3.6.1.4.1.207.8.42.8.34.6.12.1.2
This flag indicates if radar detection is enabled or not on this channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsManagedAPRadioEligibleChannelRdrDetected 1.3.6.1.4.1.207.8.42.8.34.6.12.1.3
This flag indicates if radar is detected or not on this channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsManagedAPRadioEligibleChannelLastRdrDetTime 1.3.6.1.4.1.207.8.42.8.34.6.12.1.4
Indicates the time in seconds since last radar was detected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsAssociatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.1
This table contains status parameters of clients that are currently associated with managed APs.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientStatusEntry

wsAssociatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.1.1
Each entry in this table contain client status parameters assocaited with the WS managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientStatusEntry  

wsAssociatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.1.1.1
Associated client MAC address.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientTunnelIpAddress 1.3.6.1.4.1.207.8.42.8.34.7.1.1.2
Indicates network IP address of the client station, 0.0.0.0 indicates unknown. Tunnel IP subnet is present only for clients authenticated with tunneled VAPs.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAssociatedClientUserName 1.3.6.1.4.1.207.8.42.8.34.7.1.1.3
Indicates user name of the client that have authenticated via 802.1x, clients on networks with other security modes will not have a user name.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAssociatedClientSSID 1.3.6.1.4.1.207.8.42.8.34.7.1.1.4
Indicates the network on which the client is connected.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAssociatedClientVLAN 1.3.6.1.4.1.207.8.42.8.34.7.1.1.5
If client is on VAP using VLAN data forwarding mode, indicates obsolete assigned VLAN.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..4094  

wsAssociatedClientStatus 1.3.6.1.4.1.207.8.42.8.34.7.1.1.6
This object indicates client's status.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER authenticated(1), associated(2), disassociated(3)  

wsAssociatedClientTxDataRate 1.3.6.1.4.1.207.8.42.8.34.7.1.1.7
Indicates the data rate, AP will actually support in setting up communications with client stations represented by a count from 2 - 1200, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 600 Mbit/s. Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 2..1200  

wsAssociatedClientInactivePeriod 1.3.6.1.4.1.207.8.42.8.34.7.1.1.8
For a current association, period of time that the AP has not seen any traffic for the client.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAssociatedClientDisassociateAction 1.3.6.1.4.1.207.8.42.8.34.7.1.1.9
This is an action object. Setting this object to start will initiate the disassociation of associated client. Read on this object will always return none.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsAssociatedClientAge 1.3.6.1.4.1.207.8.42.8.34.7.1.1.10
Indicates time since the controller has received new data for this client.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAssociatedClientAssociatingSwitch 1.3.6.1.4.1.207.8.42.8.34.7.1.1.11
This object indicates whether the client is associated to an AP managed by this controller or peer-controller.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER local-switch(1), peer-switch(2)  

wsAssociatedClientSwitchMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.1.1.12
MAC address of the WS associating the client.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientSwitchIpAddress 1.3.6.1.4.1.207.8.42.8.34.7.1.1.13
IP address of the WS associating the client.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

wsAssociatedClientDot11nCapable 1.3.6.1.4.1.207.8.42.8.34.7.1.1.14
Flag indicating whether this client is capable of 802.11n operation.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsAssociatedClientStbcCapable 1.3.6.1.4.1.207.8.42.8.34.7.1.1.15
Flag indicating whether this client is capable of Space Time Block Code (STBC) operation.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsAssociatedClientDistTunnelStatus 1.3.6.1.4.1.207.8.42.8.34.7.1.1.16
Indicates whether L2 Distributed Tunneling is Enabled or Disabled
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAssociatedClientDistTunnelRoamStatus 1.3.6.1.4.1.207.8.42.8.34.7.1.1.17
Indicates whether the client is using the distrubuted tunnel or not. Also indicates if it is a roamed client or not.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER associated(0), home(1)  

wsAssociatedClientDistTunnelHomeAPMac 1.3.6.1.4.1.207.8.42.8.34.7.1.1.18
Indicates MAC Address of the client's Home AP. Here the client should be associated with the network on which the L2 Distributed Tunneling is enabled.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientDistTunnelAssocAPMac 1.3.6.1.4.1.207.8.42.8.34.7.1.1.19
MAC Address of the client's Association AP to which the client has roamed to.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.1.1.20
MAC Address of the AP to which client is Associated.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientBSSID 1.3.6.1.4.1.207.8.42.8.34.7.1.1.21
BSSID of the VAP to which client is associated.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientRadioInterface 1.3.6.1.4.1.207.8.42.8.34.7.1.1.22
Indicates the radio interface on which client is associated.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAssociatedClientChannel 1.3.6.1.4.1.207.8.42.8.34.7.1.1.23
Indicates channel for associated client entry.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 1..165  

wsAssociatedClientNwTime 1.3.6.1.4.1.207.8.42.8.34.7.1.1.24
Indicates time since this client first authenticated with the network.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAssociatedClientIpAddress 1.3.6.1.4.1.207.8.42.8.34.7.1.1.25
Indicates network IPv4 address of the client station detetecd through ARP snooping, 0.0.0.0 indicates unknown.
Status: obsolete Access: read-only
OBJECT-TYPE    
  IpAddress  

wsAssociatedClientNetBiosName 1.3.6.1.4.1.207.8.42.8.34.7.1.1.26
NetBios Name of the client.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

wsAssociatedClientRRMSupported 1.3.6.1.4.1.207.8.42.8.34.7.1.1.27
Indicates if the Radio Resource Management (RRM) portion of the IEEE 802.11k standard is supported by client and RRM is enabled is on the AP Profile. Value 2 indicates the client supports RRM portion and RRM Mode is not enabled on AP Profile. Value 3 indicates client doesnot support RRM
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER enabled(1), supported(2), unsupported(3)  

wsAssociatedClientRRMLocationReportSupported 1.3.6.1.4.1.207.8.42.8.34.7.1.1.28
Indicates if the client can support RRM location report requests.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAssociatedClientRRMBeaconTableMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.7.1.1.29
Indicates if the client can detect APs via RRM beacon table reports.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAssociatedClientRRMBeaconActiveMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.7.1.1.30
Indicates if the client supports active scan capability.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAssociatedClientRRMBeaconPassiveMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.7.1.1.31
Indicates if the client supports passive scan capability.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAssociatedClientRRMChannelLoadMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.7.1.1.32
Indicates if the client supports RRM channel load measurement.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAssociatedClientStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.7.2
This table contains statistics available for each client associated to a WS managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientStatisticsEntry

wsAssociatedClientStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.7.2.1
Each entry in this table contain statistics available for each client associated a WS managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientStatisticsEntry  

wsAssociatedClientPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.2.1.1
Total packets received by a managed AP from the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.7.2.1.2
Total bytes received by a managed AP from the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.2.1.3
Total packets transmitted by a managed AP to the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.2.1.4
Total bytes transmitted by a managed AP to the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientDuplicatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.2.1.5
Total duplicate packets received from the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientFragmentedPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.2.1.6
Total fragmented packets received from the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientFragmentedPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.2.1.7
Total fragmented packets transmitted to the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientTransmitRetryCount 1.3.6.1.4.1.207.8.42.8.34.7.2.1.8
Indicates number of times transmits to client station succeeded after one or more retries.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientTransmitRetryFailedCount 1.3.6.1.4.1.207.8.42.8.34.7.2.1.9
Number of times transmits to client station failed after one or more retries.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.7.2.1.10
Total packets dropped in the receive direction by a managed AP from the client station. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.7.2.1.11
Total bytes dropped in the receive direction by a managed AP from the client station. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.7.2.1.12
Total packets dropped in the transmit direction by a managed AP to the client station. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.7.2.1.13
Total bytes dropped in the transmit direction by a managed AP to the client station. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientTsViolatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.2.1.14
Number of packets received by the AP from a client station that are in excess of the client's alotted traffic stream (TS) uplink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAssociatedClientTsViolatePktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.2.1.15
Number of packets transmitted by the AP to a client station that are in excess of the client's alotted traffic stream (TS) downlink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAssociatedClientNeighborManagedAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.3
This table is maintained to lookup all WS managed APs detected, client can see in its RF area.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientNeighborManagedAPStatusEntry

wsAssociatedClientNeighborManagedAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.3.1
Each entry in this table contain WS managed APs that can be seen by client in its RF area.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientNeighborManagedAPStatusEntry  

wsClientStationMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.3.1.1
The Ethernet address of a client station.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsClientNeighborWSManagedAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.3.1.2
The Ethernet address of a WS managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsClientNeighborWSManagedAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.7.3.1.3
The radio interface of Managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsClientStationDiscoveryReason 1.3.6.1.4.1.207.8.42.8.34.7.3.1.4
Indicates the client status with respect to the Managed AP it is refering. One or more flags can be enabled at the same time.
Status: obsolete Access: read-only
OBJECT-TYPE    
  BITS none(0), rfscan-discovered(1), neighbor-ap-associated(2), current-ap-associated(3), probe-request-discovered(4), ad-hoc-rogue(5), associated-to-peer-ap(6)  

wsVAPAssociatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.4
This table is maintained to lookup clients associated to a specific VAP on a WS managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsVAPAssociatedClientStatusEntry

wsVAPAssociatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.4.1
Each entry in this table contain clients associated to each VAP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsVAPAssociatedClientStatusEntry  

wsVAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.4.1.1
The Ethernet address assigned to a VAP.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsVAPAssociatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.4.1.2
The Ethernet address of associated client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsSSIDAssociatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.5
This table is maintained to lookup all clients associated to a particular network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSSIDAssociatedClientStatusEntry

wsSSIDAssociatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.5.1
Each entry in this table contain clients associated to a particular network.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsSSIDAssociatedClientStatusEntry  

wsSSID 1.3.6.1.4.1.207.8.42.8.34.7.5.1.1
Indicates the network on which the client is connected.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsSSIDAssociatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.5.1.2
The Ethernet address of the client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsSwitchAssociatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.6
This table is maintained to lookup clients associated to the APs managed by the specific controller.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwitchAssociatedClientStatusEntry

wsSwitchAssociatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.6.1
Each entry in this table contain client associated to each controller.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsSwitchAssociatedClientStatusEntry  

wsAssociatedClientSwitchIPAddress 1.3.6.1.4.1.207.8.42.8.34.7.6.1.1
IP address of the WS associating the client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsSwitchAssociatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.7.6.1.2
Ethernet address of the associated client station.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAssociatedClientQosStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.7
This table contains client QoS status parameters of clients that are currently associated with managed APs. These objects represent the actual operational status values in effect for the clients.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientQosStatusEntry

wsAssociatedClientQosStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.7.1
Each entry in this table contains client QoS status parameters for a client associated with the WS managed AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientQosStatusEntry  

wsAssociatedClientQosBandwidthLimitDown 1.3.6.1.4.1.207.8.42.8.34.7.7.1.1
Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client, thus controlling the maximum receive rate from the AP for this wireless client. This parameter is specified in bits-per-second (bps). The displayed value represents the actual bandwidth rate in use for the client, which may differ from the configured value since the AP rounds down to the nearest 64000 bps. A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientQosBandwidthLimitUp 1.3.6.1.4.1.207.8.42.8.34.7.7.1.2
Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP, thus controlling the maximum send rate from this wireless client to the AP. This parameter is specified in bits-per-second (bps). The displayed value represents the actual bandwidth rate in use for the client, which may differ from the configured value since the AP rounds down to the nearest 64000 bps. A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientQosAccessControlDownType 1.3.6.1.4.1.207.8.42.8.34.7.7.1.3
Access list type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosAccessControlDownName object identifies the access list.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAssociatedClientQosAccessControlDownName 1.3.6.1.4.1.207.8.42.8.34.7.7.1.4
Name of the access list in use in accordance with the wsAssociatedClientQosAccessControlDownType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosAccessControlUpType 1.3.6.1.4.1.207.8.42.8.34.7.7.1.5
Access list type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosAccessControlUpName object identifies the access list.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAssociatedClientQosAccessControlUpName 1.3.6.1.4.1.207.8.42.8.34.7.7.1.6
Name of the access list in use in accordance with the wsAssociatedClientQosAccessControlUpType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosDiffservPolicyDownType 1.3.6.1.4.1.207.8.42.8.34.7.7.1.7
DiffServ policy type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosDiffservPolicyDownName object identifies the DiffServ policy.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAssociatedClientQosDiffservPolicyDownName 1.3.6.1.4.1.207.8.42.8.34.7.7.1.8
Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosDiffservPolicyDownType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosDiffservPolicyUpType 1.3.6.1.4.1.207.8.42.8.34.7.7.1.9
DiffServ policy type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosDiffservPolicyUpName object identifies the DiffServ policy.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAssociatedClientQosDiffservPolicyUpName 1.3.6.1.4.1.207.8.42.8.34.7.7.1.10
Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosDiffservPolicyUpType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosOperStatus 1.3.6.1.4.1.207.8.42.8.34.7.7.1.11
Designates the AP quality-of-service operational status for this wireless client. This represents the combined states of the wsApClientQosMode object and the wsNetworkClientQosMode object for the wireless network to which this client is associated.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAssociatedClientSessionStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.7.8
This table contains statistics available for each client associated to a WS managed AP, but accumulated for the duration of the entire WLAN session, inclusive of client roaming.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientSessionStatisticsEntry

wsAssociatedClientSessionStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.7.8.1
Each entry in this table contain statistics available for each client associated a WS managed AP, but accumulated for the duration of the entire WLAN session, inclusive of client roaming.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientSessionStatisticsEntry  

wsAssociatedClientSessionPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.8.1.1
Total packets received by managed APs from the client station throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.7.8.1.2
Total bytes received by managed APs from the client station throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.8.1.3
Total packets transmitted by managed APs to the client station throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.8.1.4
Total bytes transmitted by managed APs to the client station throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionDuplicatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.8.1.5
Total duplicate packets received from the client station throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientSessionFragmentedPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.8.1.6
Total fragmented packets received from the client station. throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientSessionFragmentedPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.8.1.7
Total fragmented packets transmitted to the client station throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientSessionTransmitRetryCount 1.3.6.1.4.1.207.8.42.8.34.7.8.1.8
Indicates number of times transmits to client station succeeded after one or more retries throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientSessionTransmitRetryFailedCount 1.3.6.1.4.1.207.8.42.8.34.7.8.1.9
Number of times transmits to client station failed after one or more retries throughout the duration of the current WLAN session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

wsAssociatedClientSessionPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.7.8.1.10
Total packets dropped in the receive direction by managed APs from the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.7.8.1.11
Total bytes dropped in the receive direction by managed APs from the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.7.8.1.12
Total packets dropped in the transmit direction by managed APs to the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.7.8.1.13
Total bytes dropped in the transmit direction by managed APs to the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientSessionTSViolatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.7.8.1.14
Number of packets received by managed APs from a client station throughout the duration of the current WLAN session that are in excess of the client's alotted traffic stream (TS) uplink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAssociatedClientSessionTSViolatePktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.7.8.1.15
Number of packets transmitted by managed APs to a client station throughout the duration of the current WLAN session that are in excess of the client's alotted traffic stream (TS) downlink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAssociatedClientQosCachedStatusTable 1.3.6.1.4.1.207.8.42.8.34.7.9
This table contains cached client QoS status parameters of clients that are currently associated with managed APs. These objects represent values that were retrieved from a RADIUS server for this client. See the wsAssociatedClientQosStatusTable for the current set of operational values in use for this client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientQosCachedStatusEntry

wsAssociatedClientQosCachedStatusEntry 1.3.6.1.4.1.207.8.42.8.34.7.9.1
Each entry in this table contains client QoS cached status parameters for a client associated with the WS managed AP. Only those parameters successfully retrieved from a RADIUS server via 802.1X authentication on behalf of a wireless client are displayed.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientQosCachedStatusEntry  

wsAssociatedClientQosCachedBandwidthLimitDown 1.3.6.1.4.1.207.8.42.8.34.7.9.1.1
Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client, thus controlling the maximum receive rate from the AP for this wireless client. This parameter is specified in bits-per-second (bps). A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientQosCachedBandwidthLimitUp 1.3.6.1.4.1.207.8.42.8.34.7.9.1.2
Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP, thus controlling the maximum send rate from this wireless client to the AP. This parameter is specified in bits-per-second (bps). A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientQosCachedAccessControlDownType 1.3.6.1.4.1.207.8.42.8.34.7.9.1.3
Access list type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosCachedAccessControlDownName object identifies the access list.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAssociatedClientQosCachedAccessControlDownName 1.3.6.1.4.1.207.8.42.8.34.7.9.1.4
Name of the access list in use in accordance with the wsAssociatedClientQosCachedAccessControlDownType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosCachedAccessControlUpType 1.3.6.1.4.1.207.8.42.8.34.7.9.1.5
Access list type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosCachedAccessControlUpName object identifies the access list.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAssociatedClientQosCachedAccessControlUpName 1.3.6.1.4.1.207.8.42.8.34.7.9.1.6
Name of the access list in use in accordance with the wsAssociatedClientQosCachedAccessControlUpType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosCachedDiffservPolicyDownType 1.3.6.1.4.1.207.8.42.8.34.7.9.1.7
DiffServ policy type used for the wireless down (outbound) direction from the AP to this client. The wsAssociatedClientQosCachedDiffservPolicyDownName object identifies the DiffServ policy.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAssociatedClientQosCachedDiffservPolicyDownName 1.3.6.1.4.1.207.8.42.8.34.7.9.1.8
Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosCachedDiffservPolicyDownType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAssociatedClientQosCachedDiffservPolicyUpType 1.3.6.1.4.1.207.8.42.8.34.7.9.1.9
DiffServ policy type used for the wireless up (inbound) direction from this client to the AP. The wsAssociatedClientQosCachedDiffservPolicyUpName object identifies the DiffServ policy.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAssociatedClientQosCachedDiffservPolicyUpName 1.3.6.1.4.1.207.8.42.8.34.7.9.1.10
Name of the DiffServ policy in use in accordance with the wsAssociatedClientQosCachedDiffservPolicyUpType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsPeerStatusTable 1.3.6.1.4.1.207.8.42.8.34.8.1
This table contain status parameters of peer controllers of wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsPeerStatusEntry

wsPeerStatusEntry 1.3.6.1.4.1.207.8.42.8.34.8.1.1
Each entry describes the status parameters of each peer of wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsPeerStatusEntry  

wsPeerIpAddress 1.3.6.1.4.1.207.8.42.8.34.8.1.1.1
IP address of the peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsPeerClusterControllerIndicator 1.3.6.1.4.1.207.8.42.8.34.8.1.1.2
Indicates if the peer controller is currently the Cluster Controller of the peer group or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsPeerTotalPeerSwitches 1.3.6.1.4.1.207.8.42.8.34.8.1.1.3
Total number of peer controllers detected on the network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

wsPeerVendorId 1.3.6.1.4.1.207.8.42.8.34.8.1.1.4
Indicates vendor of peer controller software.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPeerProtocolVersion 1.3.6.1.4.1.207.8.42.8.34.8.1.1.5
Indicates software version of peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsPeerSoftwareVersion 1.3.6.1.4.1.207.8.42.8.34.8.1.1.6
Indicates the protocol version of software on the peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsPeerDiscoveryReason 1.3.6.1.4.1.207.8.42.8.34.8.1.1.7
Indicates the discovery method of peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ip-poll(1), l2-poll(2)  

wsPeerAge 1.3.6.1.4.1.207.8.42.8.34.8.1.1.8
Indicates time in seconds since last communication with the controller.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsPeerManagedAPCount 1.3.6.1.4.1.207.8.42.8.34.8.1.1.9
Number of APs in the peer managed AP database that are authenticated, configured, and have an active connection with the wireless controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..192  

wsPeerConfigRequestAction 1.3.6.1.4.1.207.8.42.8.34.8.1.1.10
This action object is used to: - start - Start the config push into the peer controller. - Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsPeerConfigRequestStatus 1.3.6.1.4.1.207.8.42.8.34.8.1.1.11
The status for the configuration push operation to this peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(0), requested(1), inProgress(2), invalidCodeVersion(3), invalidHwVersion(4), operationInProgress(5), invalidConfig(6), invalidPacketFormat(7), failureTimeout(8), failureGeneric(9), success(10)  

wsPeerConfigSwitchIp 1.3.6.1.4.1.207.8.42.8.34.8.1.1.12
IP Address of the last controller from which this controller received any wireless configuration data.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsPeerConfigReceived 1.3.6.1.4.1.207.8.42.8.34.8.1.1.13
Indicates which portions of configuration were last received from a peer controller. The combination of configurations are denoted by doing 'AND' of the values.BIT zero is ignored. Ex: Value 9 specifies only bit 2 and 5 are set, So it denotes channelPowerConfig and globalConfig received
Status: current Access: read-only
OBJECT-TYPE    
  BITS none(1), globalConfig(2), discoveryConfig(3), validAPDatabase(4), channelPowerConfig(5), profileNetworkConfig(6), knownClientConfig(7), captivePortalConfig(8), radiusClientConfig(9), qosAclConfig(10), qosDiffServConfig(11), wdsGroupConfig(12), deviceLocationConfig(13)  

wsPeerConfigReceivedTimestamp 1.3.6.1.4.1.207.8.42.8.34.8.1.1.14
The last time this controller received any configuration data from a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsPeerSwitchManagedAPTable 1.3.6.1.4.1.207.8.42.8.34.8.3
This table contain Managed AP database of the peer controllers of wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsPeerSwitchManagedAPEntry

wsPeerSwitchManagedAPEntry 1.3.6.1.4.1.207.8.42.8.34.8.3.1
Each entry describes the Managed AP Entry of the peer of wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsPeerSwitchManagedAPEntry  

wsPeerSwitchIpAddress 1.3.6.1.4.1.207.8.42.8.34.8.3.1.1
The IP Address of the Peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsPeerSwitchAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.8.3.1.2
The VAP0 MAC address of the AP managed by the peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsPeerSwitchAPLocation 1.3.6.1.4.1.207.8.42.8.34.8.3.1.3
This object indicates descriptive location of the managed AP by the peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsPeerSwitchAPIPAddress 1.3.6.1.4.1.207.8.42.8.34.8.3.1.4
IP address for the peer managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsPeerSwitchAPProfileId 1.3.6.1.4.1.207.8.42.8.34.8.3.1.5
Unique ID for the peer managed AP's configuration profile.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

wsPeerSwitchAPProfileName 1.3.6.1.4.1.207.8.42.8.34.8.3.1.6
The descriptive name for the peer managed AP's configuration profile.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsPeerSwitchAPHardwareType 1.3.6.1.4.1.207.8.42.8.34.8.3.1.7
The Hardware platform for the AP. 1 --> BROADCOM.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

wsRFScanAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.1
This table is maintained with RF scan data received from the WS managed APs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsRFScanAPStatusEntry

wsRFScanAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.1.1
Each entry in this table contain RF scan data received from the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsRFScanAPStatusEntry  

wsRFScanAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.1.1.1
The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsRFScanAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.9.1.1.2
If status indicates a managed AP, this indicates the radio interface on the Detected AP, if the value is unknown (i.e. Rogue or third party APs) it is set to '0'.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsRFScanAPBaseMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.1.1.3
If status indicates a managed AP, this indicates the base MAC address of the detected AP, If the value is unknown (i.e. Rogue of third party AP's) it is set to '0'.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsRFScanAPSSID 1.3.6.1.4.1.207.8.42.8.34.9.1.1.4
Service Set Id of the detected network.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsRFScanAPPhysicalMode 1.3.6.1.4.1.207.8.42.8.34.9.1.1.5
Indicates the 802.11 mode being used on an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ieee802dot11an(1), ieee802dot11bORgn(2)  

wsRFScanAPChannel 1.3.6.1.4.1.207.8.42.8.34.9.1.1.6
Indicates transmit channel of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..13 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wsRFScanAPTxRate 1.3.6.1.4.1.207.8.42.8.34.9.1.1.7
Indicates the rate at which an AP is currently transmitting data, from 1 Mbit/s to 600 Mbit/s.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsRFScanAPBeaconInterval 1.3.6.1.4.1.207.8.42.8.34.9.1.1.8
Indicates beacon interval for a neighbor AP network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 20..2000  

wsRFScanAPStatus 1.3.6.1.4.1.207.8.42.8.34.9.1.1.9
Indicates the managed status of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER managed(1), unknown(2), standalone(3), rogue(4)  

wsRFScanAPDiscoveredAge 1.3.6.1.4.1.207.8.42.8.34.9.1.1.10
Indicates timestamp in seconds when an AP was first detected.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsRFScanAPAge 1.3.6.1.4.1.207.8.42.8.34.9.1.1.11
Indicates time in seconds since an AP was last detected in the scan.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsRFScanAPStatusInitial 1.3.6.1.4.1.207.8.42.8.34.9.1.1.12
Indicates the initial status of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER managed(1), unknown(2), standalone(3), rogue(4)  

wsRFScanAPSecurityMode 1.3.6.1.4.1.207.8.42.8.34.9.1.1.13
Indicates the security mode of an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER open(1), wep(2), wpa(3)  

wsRFScanAPHighRate 1.3.6.1.4.1.207.8.42.8.34.9.1.1.14
Indicates the highest supported rate advertised by an AP in Mbps.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsRFScanAPDot11nMode 1.3.6.1.4.1.207.8.42.8.34.9.1.1.15
Indicates whether 802.11n is supported by an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

wsRFScanAPAdHoc 1.3.6.1.4.1.207.8.42.8.34.9.1.1.16
Indicates that the beacon frame was received from an ad hoc network for an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notadhoc(0), adhoc(1)  

wsRFScanAPPeerManaged 1.3.6.1.4.1.207.8.42.8.34.9.1.1.17
Indicates that an AP is managed by a peer controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER localswitch(0), peerswitch(1)  

wsRFScanAPRogueMitigation 1.3.6.1.4.1.207.8.42.8.34.9.1.1.18
Indicates whether rogue AP mitigation is in progress for an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notrogue(0), inprogress(1), attackdisabled(2), toomany(3), illegalchannel(4), spoofing(5), adhoc(6)  

wsRFScanAPAcknowledgeRogue 1.3.6.1.4.1.207.8.42.8.34.9.1.1.19
This is a command that allows the administrator to restore the initial status for this AP in the RF Scan database. Read on this object will always return no-action.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no-action(0), acknowledge(1)  

wsRFScanAPBSSID 1.3.6.1.4.1.207.8.42.8.34.9.1.1.20
BSSID advertised in the network.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsRFScanAPOUI 1.3.6.1.4.1.207.8.42.8.34.9.1.1.21
Manufacturer information for this AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsRFScanAPRRMSupported 1.3.6.1.4.1.207.8.42.8.34.9.1.1.22
Advertised status of Radio Resource Management (RRM) capability.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER unsupported(0), supported(1)  

wsRFScanAPDot11acMode 1.3.6.1.4.1.207.8.42.8.34.9.1.1.23
Indicates whether 802.11ac is supported by an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

wsRFScanAPEntriesPurge 1.3.6.1.4.1.207.8.42.8.34.9.2
This is an action object used to purge the RF scan entries present in the network. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsFailureAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.3
This table contain status parameters of APs that failed to authenticate, or associate with wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsFailureAPStatusEntry

wsFailureAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.3.1
Each entry in this table contain status parameters of failed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsFailureAPStatusEntry  

wsFailedAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.3.1.1
The Ethernet address of the failed AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsFailedAPIpAddress 1.3.6.1.4.1.207.8.42.8.34.9.3.1.2
The network IP address of the failed AP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsFailedAPVendorId 1.3.6.1.4.1.207.8.42.8.34.9.3.1.3
Indicates vendor of the failed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER broadcom(1), others(65535)  

wsFailedAPSoftwareVersion 1.3.6.1.4.1.207.8.42.8.34.9.3.1.4
Indicates software version of the failed AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsFailedAPHWType 1.3.6.1.4.1.207.8.42.8.34.9.3.1.5
Indicates hardware type of the failed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER reserved-1(1), reserved-2(2), reserved-3(3), reserved-4(4), tq3600(5), reserved-6(6), reserved-7(7), tq3200(8), tq2450(9), tq3400(10), reserved-11(11), tq4400(12), tq4600(13)  

wsFailedAPFailureType 1.3.6.1.4.1.207.8.42.8.34.9.3.1.6
Indicates the last type of failure that occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER localAuthentication(1), noDbEntry(2), notManaged(3), radiusAuthentication(4), radiusChallenged(5), radiusUnreachable(6), invalidRadiusResponse(7), invalidProfileId(8), profileMismatch(9), radiusMsgSendFailed(10), noAPImageAvailable(11)  

wsFailedAPValidationFailureCount 1.3.6.1.4.1.207.8.42.8.34.9.3.1.7
Number of times the AP failed to authenticate due to MAC address validation failure.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsFailedAPAuthenticationFailureCount 1.3.6.1.4.1.207.8.42.8.34.9.3.1.8
Number of times the AP failed to authenticate due to incorrect authentication credentials.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsFailedAPProtocolVersion 1.3.6.1.4.1.207.8.42.8.34.9.3.1.9
Indicates the protocol version supported by the software on this AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

wsFailedAPAge 1.3.6.1.4.1.207.8.42.8.34.9.3.1.10
Indicates time since failure occured.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsFailedAPReportingSwitch 1.3.6.1.4.1.207.8.42.8.34.9.3.1.11
This object indicates whether the AP failure happened on this controller or on the peer-controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local-switch(1), peer-switch(2)  

wsFailedAPSwitchMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.3.1.12
MAC address of the WS reporting the AP Authentication Failure.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsFailedAPSwitchIpAddress 1.3.6.1.4.1.207.8.42.8.34.9.3.1.13
IP address of the WS reporting the AP Authentication Failure.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsAPFailureEntriesPurge 1.3.6.1.4.1.207.8.42.8.34.9.4
This is an action object used to purge the failed AP entries. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAdHocClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.5
This table contains information related to Ad hoc clients detected in the network.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAdHocClientStatusEntry

wsAdHocClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.5.1
Each entry in this table represents Ad hoc client detected in the network.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAdHocClientStatusEntry  

wsAdHocClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.5.1.1
The Ethernet address of the Ad hoc client detected. If detection Mode is 'Beacon' then the client is represented as an AP in the RF Scan database and the Neighbor AP List. If the detection mode is 'Data Frame' then the client information is in the Neighbor Client List.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.5.1.2
The MAC address of an AP which last detected the Ad hoc client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.9.5.1.3
The radio interface of an AP which last detected the Ad hoc client.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAdHocClientDetectionMode 1.3.6.1.4.1.207.8.42.8.34.9.5.1.4
The mechanism through which this Ad hoc device is detected. This can be through beacon frame or data frame.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER beacon-frame(1), data-frame(2)  

wsAdHocClientAge 1.3.6.1.4.1.207.8.42.8.34.9.5.1.5
Indicates time since the last detection of this Ad hoc client.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAdHocClientEntriesPurge 1.3.6.1.4.1.207.8.42.8.34.9.6
This is an action object used to purge the ad-hoc client entries. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPTriangulationNonSentryStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.7
This table contains triangulation data to help the administrator determine which non-sentry APs are detecting the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPTriangulationNonSentryStatusEntry

wsAPTriangulationNonSentryStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.7.1
Each entry in this table contains triangulation information for the RF Scan entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPTriangulationNonSentryStatusEntry  

wsAPTriangulationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.7.1.1
The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPTriangulationId 1.3.6.1.4.1.207.8.42.8.34.9.7.1.2
Index of the sentry triangulation entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

wsAPTriangulationNonSentryMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.7.1.3
The MAC address of the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPTriangulationNonSentryRadio 1.3.6.1.4.1.207.8.42.8.34.9.7.1.4
The radio of the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAPTriangulationRssi 1.3.6.1.4.1.207.8.42.8.34.9.7.1.5
Received signal strength indicator in percent (0 to 100%).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsAPTriangulationStrength 1.3.6.1.4.1.207.8.42.8.34.9.7.1.6
Received signal strength in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsAPTriangulationNoise 1.3.6.1.4.1.207.8.42.8.34.9.7.1.7
Noise reported on the channel by the AP in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsAPTriangulationAge 1.3.6.1.4.1.207.8.42.8.34.9.7.1.8
Indicates the age since this device was most recently detected by the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAPTriangulationSentryStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.8
This table contains triangulation data to help the administrator determine which sentry APs are detecting the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPTriangulationSentryStatusEntry

wsAPTriangulationSentryStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.8.1
Each entry in this table contains triangulation information for the RF Scan entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPTriangulationSentryStatusEntry  

wsAPSentryTriangulationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.8.1.1
The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPSentryTriangulationId 1.3.6.1.4.1.207.8.42.8.34.9.8.1.2
Index of the sentry triangulation entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

wsAPSentryTriangulationSentryMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.8.1.3
The MAC address of the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPSentryTriangulationSentryRadio 1.3.6.1.4.1.207.8.42.8.34.9.8.1.4
The radio of the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAPSentryTriangulationRssi 1.3.6.1.4.1.207.8.42.8.34.9.8.1.5
Received signal strength indicator in percent (0 to 100%).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsAPSentryTriangulationStrength 1.3.6.1.4.1.207.8.42.8.34.9.8.1.6
Received signal strength in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsAPSentryTriangulationNoise 1.3.6.1.4.1.207.8.42.8.34.9.8.1.7
Noise reported on the channel by the AP in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsAPSentryTriangulationAge 1.3.6.1.4.1.207.8.42.8.34.9.8.1.8
Indicates age since this device was most recently detected by the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAPRogueClassificationStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.9
This table contains rogue classification test results.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPRogueClassificationStatusEntry

wsAPRogueClassificationStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.9.1
Each entry in this table contains triangulation information for the RF Scan entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPRogueClassificationStatusEntry  

wsAPRogueClassificationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.9.1.1
The MAC address of the detected AP, this could be a physical radio interface or VAP MAC.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPRogueClassificationTestId 1.3.6.1.4.1.207.8.42.8.34.9.9.1.2
The rogue classification test id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..10  

wsAPRogueClassificationTestName 1.3.6.1.4.1.207.8.42.8.34.9.9.1.3
The rogue classification test identifier.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER widsaprogue01(0), widsaprogue02(1), widsaprogue03(2), widsaprogue04(3), widsaprogue05(4), widsaprogue06(5), widsaprogue07(6), widsaprogue08(7), widsaprogue09(8), widsaprogue10(9), widsaprogue11(10)  

wsAPRogueClassificationDetected 1.3.6.1.4.1.207.8.42.8.34.9.9.1.4
Indicates whether this test detected the condition that it is designed to detect.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notdetected(0), detected(1)  

wsAPRogueClassificationReportingAPMac 1.3.6.1.4.1.207.8.42.8.34.9.9.1.5
The MAC address of the managed AP that last reported detecting this condition.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPRogueClassificationReportingAPRadio 1.3.6.1.4.1.207.8.42.8.34.9.9.1.6
The radio number of the managed AP that last reported detecting this condition. Zero indicates no report available
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

wsAPRogueClassificationTestState 1.3.6.1.4.1.207.8.42.8.34.9.9.1.7
Indicates whether this test is configured to report rogues.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wsAPRogueClassificationTestResult 1.3.6.1.4.1.207.8.42.8.34.9.9.1.8
Indicates whether this test reported the device as rogue.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notreported(0), roguereported(1)  

wsAPRogueClassificationFirstTime 1.3.6.1.4.1.207.8.42.8.34.9.9.1.9
Indicates how long ago this test first detected the condition.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAPRogueClassificationLastTime 1.3.6.1.4.1.207.8.42.8.34.9.9.1.10
Indicates how long ago this test last detected the condition.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAPDeAuthenticationAttackStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.10
This table contains the AP de-authentication attack status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPDeAuthenticationAttackStatusEntry

wsAPDeAuthenticationAttackStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.10.1
This table contains information about APs against which the Cluster Controller initiated a de-authentication attack.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPDeAuthenticationAttackStatusEntry  

wsAPDeAuthenticationAttackStatusId 1.3.6.1.4.1.207.8.42.8.34.9.10.1.1
The AP de-authentication attack status table index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..16  

wsAPDeAuthenticationAttackBSSID 1.3.6.1.4.1.207.8.42.8.34.9.10.1.2
BSSID of the AP against which the attack is launched.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAPDeAuthenticationAttackChannel 1.3.6.1.4.1.207.8.42.8.34.9.10.1.3
Channel on which the rogue AP is operating.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..161  

wsAPDeAuthenticationAttackTime 1.3.6.1.4.1.207.8.42.8.34.9.10.1.4
Time since attack started on this AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAPDeAuthenticationAttackAge 1.3.6.1.4.1.207.8.42.8.34.9.10.1.5
Time since RF Scan report about this AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.11
This table contains status parameters of clients that are currently detected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDetectedClientStatusEntry

wsDetectedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.11.1
Each entry in this table contains detected client status parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDetectedClientStatusEntry  

wsDetectedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.9.11.1.1
Detected client MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientStatus 1.3.6.1.4.1.207.8.42.8.34.9.11.1.2
This object indicates client's status. Authenticated- Client is Authenticated with the system and is not Rogue Detected- Client is detected, not Authenticated, not rogue, and is not found in the Known Clients Database. Known- Client is detected, but is not authenticated. Black-Listed- Client tried to associate with the system, but was rejected due to MAC authentication. Rogue- Client failed of the the enabled threat tests.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER authenticated(0), detected(1), known(2), black-listed(3), rogue(4)  

wsDetectedClientAuthStatus 1.3.6.1.4.1.207.8.42.8.34.9.11.1.3
This object indicates client's authentication status. Note that the Client Status can be Rogue, but the client can be Authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-authenticated(0), authenticated(1)  

wsDetectedClientEntryLastUpdatedAt 1.3.6.1.4.1.207.8.42.8.34.9.11.1.4
This object indicates time since any event has been received for this client that updated the detected client database entry.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientThreatDetectedStatus 1.3.6.1.4.1.207.8.42.8.34.9.11.1.5
This object indicates if any one of the threat detection tests have been triggered for this client. If the test is disabled the client won't be marked as Rogue, but administrator may still be interested in investigating why the threat triggered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-detected(0), detected(1)  

wsDetectedClientThreatMitigationStatus 1.3.6.1.4.1.207.8.42.8.34.9.11.1.6
This object indicates whether threat mitigation has been done for this client.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-done(0), done(1)  

wsDetectedClientName 1.3.6.1.4.1.207.8.42.8.34.9.11.1.7
Nickname from the Known Client Database. If client is not in the database then the nickname is blank.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsDetectedClientEntryCreateTime 1.3.6.1.4.1.207.8.42.8.34.9.11.1.8
Indicates the time the detected client entry was created.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientChannel 1.3.6.1.4.1.207.8.42.8.34.9.11.1.9
this object indicates channel number in which the client is dtected
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100  

wsDetectedClientAuthRSSI 1.3.6.1.4.1.207.8.42.8.34.9.11.1.10
If the client is authenticated with the managed AP then this object indicates Received Signal Strength(RSSI) value reported by the AP with which the client is authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100  

wsDetectedClientAuthSignal 1.3.6.1.4.1.207.8.42.8.34.9.11.1.11
This object indicates the last signal strength(in dBm) reported by the managed AP with which the client is authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -128..128  

wsDetectedClientAuthNoise 1.3.6.1.4.1.207.8.42.8.34.9.11.1.12
This object indicates the last channel noise(in dBm) reported by the managed AP with which the client is authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -128..128  

wsDetectedClientProbeReqRecorded 1.3.6.1.4.1.207.8.42.8.34.9.11.1.13
This object indicates the number of probe requests recorded so far during the probe collection interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientProbeCollectionIntvl 1.3.6.1.4.1.207.8.42.8.34.9.11.1.14
This object indicates how much time is left before the probe collection interval is done and the controller decides whether the client is a threat.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientHighestNumProbes 1.3.6.1.4.1.207.8.42.8.34.9.11.1.15
This object indicates the largest number of probes that the controller detected during the collection interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientAuthMsgsRecorded 1.3.6.1.4.1.207.8.42.8.34.9.11.1.16
This object indicates the number of 802.11 authentication messages recorded so far during the auth collection interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientAuthCollectionIntvl 1.3.6.1.4.1.207.8.42.8.34.9.11.1.17
This object indicates how much time is left before the authentication collection interval is done and the controller decides whether the client is a threat.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientHighestNumAuthMsgs 1.3.6.1.4.1.207.8.42.8.34.9.11.1.18
This object indicates the largest number of authentications that the controller detected during the collection interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientDeAuthMsgsRecorded 1.3.6.1.4.1.207.8.42.8.34.9.11.1.19
This object indicates the number of 802.11 de-authentication messages recorded so far during the de-auth collection interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientDeAuthCollectionIntvl 1.3.6.1.4.1.207.8.42.8.34.9.11.1.20
This object indicates how much time is left before the de-authentication collection interval is done and the controller decides whether the client is a threat.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientHighestNumDeAuthMsgs 1.3.6.1.4.1.207.8.42.8.34.9.11.1.21
This object indicates the largest number of de-authentication messages that the controller detected during the collection interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientAuthFailures 1.3.6.1.4.1.207.8.42.8.34.9.11.1.22
This object indicates the number of 802.1X Authentication failures detected for this client.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientProbesDetected 1.3.6.1.4.1.207.8.42.8.34.9.11.1.23
This object indicates the number of probes detected in the last RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientBcastBSSIDProbes 1.3.6.1.4.1.207.8.42.8.34.9.11.1.24
This object indicates the number of probes to broadcast BSSID in the last RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientBcastSSIDProbes 1.3.6.1.4.1.207.8.42.8.34.9.11.1.25
This object indicates the number of probes to broadcast SSID in the last RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientSpecificBSSIDProbes 1.3.6.1.4.1.207.8.42.8.34.9.11.1.26
This object indicates the number of probes to specific BSSID in the last RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientSpecificSSIDProbes 1.3.6.1.4.1.207.8.42.8.34.9.11.1.27
This object indicates the number of probes to specific SSID in the last RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientLastNonBcastBSSID 1.3.6.1.4.1.207.8.42.8.34.9.11.1.28
This object indicates the last non-broadcast BSSID detected in the RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientLastNonBcastSSID 1.3.6.1.4.1.207.8.42.8.34.9.11.1.29
This object indicates the last non-broadcast SSID detected in the RF Scan.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsDetectedClientThreatMitigationSent 1.3.6.1.4.1.207.8.42.8.34.9.11.1.30
This object indicates the time since the controller sent the last threat mitigation message to this client.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientEntryPurge 1.3.6.1.4.1.207.8.42.8.34.9.11.1.31
This is an action object. Setting this object to enable will purge the detected client entry except entries for authenticated clients. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsDetectedClientEntryAcknowledge 1.3.6.1.4.1.207.8.42.8.34.9.11.1.32
This is a command that allows the administrator to clear the rogue status for the entry in the Detected clients database
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no-action(0), acknowledge(1)  

wsDetectedClientOUI 1.3.6.1.4.1.207.8.42.8.34.9.11.1.33
Device manufacturer information for this Detected client.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsDetectedClientPurgeAll 1.3.6.1.4.1.207.8.42.8.34.9.12
This is an action object. Setting this object to enable will purge all the detected clients entries except entries for authenticated clients. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsDetectedClientAcknowledgeAll 1.3.6.1.4.1.207.8.42.8.34.9.13
This is a command that allows the administrator to clear the rogue status for all entries in the Detected clients database
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no-action(0), acknowledge(1)  

wsClientRogueClassificationStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.14
This table contains rogue classification test results for clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsClientRogueClassificationStatusEntry

wsClientRogueClassificationStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.14.1
Each entry in this table contains rogue classification test results for a client.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsClientRogueClassificationStatusEntry  

wsClientRogueClassificationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.14.1.1
The MAC address of the detected client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsClientRogueClassificationTestId 1.3.6.1.4.1.207.8.42.8.34.9.14.1.2
The rogue classification test id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..10  

wsClientRogueClassificationTestName 1.3.6.1.4.1.207.8.42.8.34.9.14.1.3
The rogue classification test identifier.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER widsclientrogue01(0), widsclientrogue02(1), widsclientrogue03(2), widsclientrogue04(3), widsclientrogue05(4), widsclientrogue06(5), widsclientrogue07(6)  

wsClientRogueClassificationDetected 1.3.6.1.4.1.207.8.42.8.34.9.14.1.4
Indicates whether this test detected the condition that it is designed to detect.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notdetected(0), detected(1)  

wsClientRogueClassificationReportingAPMac 1.3.6.1.4.1.207.8.42.8.34.9.14.1.5
The MAC address of the managed AP that last reported detecting this condition.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsClientRogueClassificationReportingAPRadio 1.3.6.1.4.1.207.8.42.8.34.9.14.1.6
The radio number of the managed AP that last reported detecting this condition. Zero indicates no report available
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

wsClientRogueClassificationTestState 1.3.6.1.4.1.207.8.42.8.34.9.14.1.7
Indicates whether this test is configured to report rogues.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wsClientRogueClassificationTestResult 1.3.6.1.4.1.207.8.42.8.34.9.14.1.8
Indicates whether this test reported the device as rogue.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notreported(0), roguereported(1)  

wsClientRogueClassificationFirstTime 1.3.6.1.4.1.207.8.42.8.34.9.14.1.9
Indicates how long ago this test first detected the condition.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsClientRogueClassificationLastTime 1.3.6.1.4.1.207.8.42.8.34.9.14.1.10
Indicates how long ago this test last detected the condition.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientTriangulationNonSentryStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.15
This table contains triangulation data to help the administrator determine which three managed non-sentry APs are detecting the client along with the signal strength and the time stamp.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDetectedClientTriangulationNonSentryStatusEntry

wsDetectedClientTriangulationNonSentryStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.15.1
Each entry in this table contains triangulation information for the Detected Client entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDetectedClientTriangulationNonSentryStatusEntry  

wsDetectedClientTriangulationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.15.1.1
The MAC address of the Detected Client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientTriangulationId 1.3.6.1.4.1.207.8.42.8.34.9.15.1.2
Index of the non sentry triangulation entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

wsDetectedClientTriangulationNonSentryMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.15.1.3
The MAC address of the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientTriangulationNonSentryRadio 1.3.6.1.4.1.207.8.42.8.34.9.15.1.4
The radio of the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsDetectedClientTriangulationRssi 1.3.6.1.4.1.207.8.42.8.34.9.15.1.5
Received signal strength indicator in percent (0 to 100%).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsDetectedClientTriangulationStrength 1.3.6.1.4.1.207.8.42.8.34.9.15.1.6
Received signal strength in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsDetectedClientTriangulationNoise 1.3.6.1.4.1.207.8.42.8.34.9.15.1.7
Noise reported on the channel by the AP in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsDetectedClientTriangulationAge 1.3.6.1.4.1.207.8.42.8.34.9.15.1.8
Indicates the time since this device was most recently detected by the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientTriangulationSentryStatusTable 1.3.6.1.4.1.207.8.42.8.34.9.16
This table contains triangulation data to help the administrator determine which three managed sentry APs are detecting the client along with the signal strength and the time stamp.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDetectedClientTriangulationSentryStatusEntry

wsDetectedClientTriangulationSentryStatusEntry 1.3.6.1.4.1.207.8.42.8.34.9.16.1
Each entry in this table contains triangulation information for the Detected Client entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDetectedClientTriangulationSentryStatusEntry  

wsDetectedClientSentryTriangulationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.16.1.1
The MAC address of the detected client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientSentryTriangulationId 1.3.6.1.4.1.207.8.42.8.34.9.16.1.2
Index of the sentry triangulation entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2  

wsDetectedClientSentryTriangulationSentryMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.16.1.3
The MAC address of the AP detecting the client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientSentryTriangulationSentryRadio 1.3.6.1.4.1.207.8.42.8.34.9.16.1.4
The radio of the AP detecting the client.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsDetectedClientSentryTriangulationRssi 1.3.6.1.4.1.207.8.42.8.34.9.16.1.5
Received signal strength indicator in percent (0 to 100%).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

wsDetectedClientSentryTriangulationStrength 1.3.6.1.4.1.207.8.42.8.34.9.16.1.6
Received signal strength in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsDetectedClientSentryTriangulationNoise 1.3.6.1.4.1.207.8.42.8.34.9.16.1.7
Noise reported on the channel by the AP in dBm (-127 to 127).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..127  

wsDetectedClientSentryTriangulationAge 1.3.6.1.4.1.207.8.42.8.34.9.16.1.8
Indicates time since this device was most recently detected by the detecting AP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientPreAuthenticationHistoryTable 1.3.6.1.4.1.207.8.42.8.34.9.17
This table contains pre-authentication history entries for detected clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDetectedClientPreAuthenticationHistoryEntry

wsDetectedClientPreAuthenticationHistoryEntry 1.3.6.1.4.1.207.8.42.8.34.9.17.1
Each entry in this table contains details of pre-authentication events occured for the detected client.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDetectedClientPreAuthenticationHistoryEntry  

wsDetectedClientPreAuthenticationMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.17.1.1
The MAC address of the detected client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientPreAuthenticationId 1.3.6.1.4.1.207.8.42.8.34.9.17.1.2
Numeric identifier for the preAuthentication entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientPreAuthenticationApMac 1.3.6.1.4.1.207.8.42.8.34.9.17.1.3
The Ethernet address of the AP with which client has pre-authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientPreAuthenticationApRadioId 1.3.6.1.4.1.207.8.42.8.34.9.17.1.4
The radio number of this radio in the AP with which client has pre-authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsDetectedClientPreAuthenticationVapMac 1.3.6.1.4.1.207.8.42.8.34.9.17.1.5
The MAC address of the VAP to which client has roamed.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientPreAuthenticationSSID 1.3.6.1.4.1.207.8.42.8.34.9.17.1.6
This object indicates the SSID used by the VAP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsDetectedClientPreAuthenticationAge 1.3.6.1.4.1.207.8.42.8.34.9.17.1.7
Indicates time since this history event occured.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientPreAuthenticationStatus 1.3.6.1.4.1.207.8.42.8.34.9.17.1.8
Designates the pre-authentication operational status for this detected client.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(0), failure(1)  

wsDetectedClientPreAuthenticationHistoryPurgeAll 1.3.6.1.4.1.207.8.42.8.34.9.18
This is an action object. Setting this object to enable will purge all the pre-authentication history entries for all the detected clients. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsDetectedClientRoamHistoryTable 1.3.6.1.4.1.207.8.42.8.34.9.19
This table contains roam history entries for detected clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDetectedClientRoamHistoryEntry

wsDetectedClientRoamHistoryEntry 1.3.6.1.4.1.207.8.42.8.34.9.19.1
Each entry in this table contains details of roam events occured for the detected client.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDetectedClientRoamHistoryEntry  

wsDetectedClientRoamMacAddr 1.3.6.1.4.1.207.8.42.8.34.9.19.1.1
The MAC address of the detected client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientRoamId 1.3.6.1.4.1.207.8.42.8.34.9.19.1.2
Numeric identifier for the Roam entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsDetectedClientRoamApMac 1.3.6.1.4.1.207.8.42.8.34.9.19.1.3
The Ethernet address of the AP to which client has roamed.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientRoamApRadioId 1.3.6.1.4.1.207.8.42.8.34.9.19.1.4
The radio number of this radio in the AP with which client has roamed.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsDetectedClientRoamVapMac 1.3.6.1.4.1.207.8.42.8.34.9.19.1.5
The MAC address of the VAP to which client has roamed.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDetectedClientRoamSSID 1.3.6.1.4.1.207.8.42.8.34.9.19.1.6
This object indicates the SSID used by the VAP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsDetectedClientRoamAge 1.3.6.1.4.1.207.8.42.8.34.9.19.1.7
Indicates time since this roam history event occured.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsDetectedClientRoamStatus 1.3.6.1.4.1.207.8.42.8.34.9.19.1.8
Designates the roaming operational status for this detected client.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER newAuthentication(1), roam(2)  

wsDetectedClientRoamHistoryPurgeAll 1.3.6.1.4.1.207.8.42.8.34.9.20
This is an action object. Setting this object to enable will purge all the roaming history entries for all the detected clients. Read on this object will always return disable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsRrmNeighborTable 1.3.6.1.4.1.207.8.42.8.34.15.1
This table displays the known neighbors of each AP/VAP pair as reported through RF scans that conform to the IEEE 802.11k standards for Radio Resource Measurement (RRM).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsRrmNeighborEntry

wsRrmNeighborEntry 1.3.6.1.4.1.207.8.42.8.34.15.1.1
Each entry provides information regarding known neighboring APs that may be suitable for client roaming.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsRrmNeighborEntry  

wsRrmNeighborApMacAddr 1.3.6.1.4.1.207.8.42.8.34.15.1.1.1
The MAC address of the managed AP that detected the neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmNeighborVapMacAddr 1.3.6.1.4.1.207.8.42.8.34.15.1.1.2
The MAC address of the VAP that detected the neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmNeighborMacAddr 1.3.6.1.4.1.207.8.42.8.34.15.1.1.3
The MAC address of the detected neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmNeighborRSSI 1.3.6.1.4.1.207.8.42.8.34.15.1.1.4
The RSSI (signal strength) of the detected neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..100  

wsRrmNeighborSSID 1.3.6.1.4.1.207.8.42.8.34.15.1.1.5
The SSID of the detected neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsRrmNeighborChannel 1.3.6.1.4.1.207.8.42.8.34.15.1.1.6
The channel of the detected neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsRrmNeighborAge 1.3.6.1.4.1.207.8.42.8.34.15.1.1.7
The age, in seconds, of this table entry for the detected neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  TimeTicks  

wsRrmNeighborAllPurge 1.3.6.1.4.1.207.8.42.8.34.15.1.1.8
This is an action object used to purge all neighbors. Reads on this object will always return disable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsRrmNeighborApPurge 1.3.6.1.4.1.207.8.42.8.34.15.1.1.9
This is an action object used to purge all neighbors detected by the managed AP described by this entry. Reads on this object will always return disable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsRrmNeighborVapPurge 1.3.6.1.4.1.207.8.42.8.34.15.1.1.10
This is an action object used to purge all neighbors detected by the VAP described by this entry. Reads on this object will always return disable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsRrmChannelLoadHistoryTable 1.3.6.1.4.1.207.8.42.8.34.16.1
This table displays the known channel load measurement history items. Channel load measurements are part of the IEEE 802.11k standards for Radio Resource Measurement (RRM).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsRrmChannelLoadHistoryEntry

wsRrmChannelLoadHistoryEntry 1.3.6.1.4.1.207.8.42.8.34.16.1.1
Each entry provides information regarding previous channel load measurement reports from clients .
Status: current Access: not-accessible
OBJECT-TYPE    
  WsRrmChannelLoadHistoryEntry  

wsRrmChannelLoadHistoryEntryId 1.3.6.1.4.1.207.8.42.8.34.16.1.1.1
A unique identifier for a history entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsRrmChannelLoadHistoryEntryApMacAddr 1.3.6.1.4.1.207.8.42.8.34.16.1.1.2
The MAC address of the managed AP associated to the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmChannelLoadHistoryEntryClientMacAddr 1.3.6.1.4.1.207.8.42.8.34.16.1.1.3
The MAC address of client that conducted the measurement.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmChannelLoadHistoryEntryChannel 1.3.6.1.4.1.207.8.42.8.34.16.1.1.4
The channel used for the measurement.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsRrmChannelLoadHistoryEntryAge 1.3.6.1.4.1.207.8.42.8.34.16.1.1.5
The age of the measurement history entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  TimeTicks  

wsRrmChannelLoadHistoryEntryLoad 1.3.6.1.4.1.207.8.42.8.34.16.1.1.6
The measured load, expressed as a percentage.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..100  

wsRrmChannelLoadHistoryEntryDuration 1.3.6.1.4.1.207.8.42.8.34.16.1.1.7
The duration of the measurement, expressed in time units (TUs), where one TU equals 1024 microseconds.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..65535  

wsRrmChannelLoadCurrentRequest 1.3.6.1.4.1.207.8.42.8.34.16.2
OBJECT IDENTIFIER    

wsRrmChannelLoadCurrentRequestClientMacAddr 1.3.6.1.4.1.207.8.42.8.34.16.2.1
The MAC address of client involved with the request.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmChannelLoadCurrentRequestApMacAddr 1.3.6.1.4.1.207.8.42.8.34.16.2.2
The MAC address of the managed AP associated with the client involved with the request.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmChannelLoadCurrentRequestChannel 1.3.6.1.4.1.207.8.42.8.34.16.2.3
The channel specified within the current request.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsRrmChannelLoadCurrentRequestDuration 1.3.6.1.4.1.207.8.42.8.34.16.2.4
The duration specified in the current request, expressed in time units (TUs), where one TU equals 1024 microseconds.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..65535  

wsRrmChannelLoadCurrentRequestStatus 1.3.6.1.4.1.207.8.42.8.34.16.2.5
The status of the current request.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER notStarted(0), success(1), inProgress(2), timedOut(3), aborted(4), incapable(5), refused(6)  

wsRrmChannelLoadCurrentRequestTimeRemaining 1.3.6.1.4.1.207.8.42.8.34.16.2.6
The time remaining for the current request.
Status: current Access: not-accessible
OBJECT-TYPE    
  TimeTicks  

wsRrmChannelLoadCurrentRequestAbort 1.3.6.1.4.1.207.8.42.8.34.16.2.7
Aborts a pending request if 'yes' given as value. Reads of this element will always return 'no'.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

wsRrmChannelLoadNewRequest 1.3.6.1.4.1.207.8.42.8.34.16.3
OBJECT IDENTIFIER    

wsRrmChannelLoadNewRequestClientMacAddr 1.3.6.1.4.1.207.8.42.8.34.16.3.1
The MAC address of client chosen to execute the new request.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsRrmChannelLoadNewRequestChannel 1.3.6.1.4.1.207.8.42.8.34.16.3.2
The channel to be used in the next submitted request.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..14 | 36 | 40 | 42 | 44 | 48 | 50 | 52 | 56 | 58 | 60 | 64 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 149 | 152 | 153 | 157 | 160 | 161 | 165  

wsRrmChannelLoadNewRequestDuration 1.3.6.1.4.1.207.8.42.8.34.16.3.3
The duration to be used in the next request, expressed in time units (TUs), where one TU equals 1024 microseconds.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..65535  

wsRrmChannelLoadNewRequestSend 1.3.6.1.4.1.207.8.42.8.34.16.3.4
Sends a new request if 'yes' given as value. Reads of this element will always return 'no'.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

wsAPHardwareCapabilityTable 1.3.6.1.4.1.207.8.42.8.34.12.1
This table defines supported features for APs of specific hardware type. This is a read only table and is used by application to validate parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPHardwareCapabilityEntry

wsAPHardwareCapabilityEntry 1.3.6.1.4.1.207.8.42.8.34.12.1.1
Each entry provides access point hardware type details for each AP hardware type supported by the WS.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPHardwareCapabilityEntry  

wsAPHWTypeID 1.3.6.1.4.1.207.8.42.8.34.12.1.1.1
Numeric identifier for the AP hardware type.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..13  

wsAPHWTypeDescription 1.3.6.1.4.1.207.8.42.8.34.12.1.1.2
Descriptive name of the AP hardware type.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsAPHWTypeRadioCount 1.3.6.1.4.1.207.8.42.8.34.12.1.1.3
Number of radios supported by this hardware type AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsAPImageTypeID 1.3.6.1.4.1.207.8.42.8.34.12.1.1.4
Image type for code download for this hardware type AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsAPHWDualBootSuppport 1.3.6.1.4.1.207.8.42.8.34.12.1.1.5
Dual boot support for this hardware type AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

wsAPHardwareRadioCapabilityTable 1.3.6.1.4.1.207.8.42.8.34.12.2
The AP harware radio capability table contain only those parameters that vary from one AP hardware type to another. Parameters that don't vary depending on AP type or radio type are not included in the table.This read-only table provides the user to view configurable parameters for the APs of specific hardware type through the profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPHardwareRadioCapabilityEntry

wsAPHardwareRadioCapabilityEntry 1.3.6.1.4.1.207.8.42.8.34.12.2.1
Each entry provides radio capability details for each AP hardware type supported by the WS.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPHardwareRadioCapabilityEntry  

wsAPHWTypeRadioNum 1.3.6.1.4.1.207.8.42.8.34.12.2.1.1
The radio number of this radio in the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsAPHWTypeRadioID 1.3.6.1.4.1.207.8.42.8.34.12.2.1.2
The device id for this radio in the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..43421  

wsAPHWTypeRadioDescription 1.3.6.1.4.1.207.8.42.8.34.12.2.1.3
Text description of this radio type.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsAPHWTypeRadioVapCount 1.3.6.1.4.1.207.8.42.8.34.12.2.1.4
Number of virtual access points supported by this radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

wsAPHWTypeRadioAmodeSupport 1.3.6.1.4.1.207.8.42.8.34.12.2.1.5
Flag indicating whether this radio supports 802.11a mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPHWTypeRadioBGmodeSupport 1.3.6.1.4.1.207.8.42.8.34.12.2.1.6
Flag indicating whether this radio supports 802.11bg mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPHWTypeRadioNmodeSupport 1.3.6.1.4.1.207.8.42.8.34.12.2.1.7
Flag indicating whether this radio supports 802.11n configuration parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPHWTypeRadioACmodeSupport 1.3.6.1.4.1.207.8.42.8.34.12.2.1.8
Flag indicating whether this radio supports 802.11ac configuration parameters.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPImageTypeCapabilityTable 1.3.6.1.4.1.207.8.42.8.34.12.3
This table defines supported image types for APs. This is a read only table and is used by application to view possible image types
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPImageTypeCapabilityEntry

wsAPImageTypeCapabilityEntry 1.3.6.1.4.1.207.8.42.8.34.12.3.1
Each entry provides access point image type details for each AP image type supported by the WS.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPImageTypeCapabilityEntry  

wsAPImageTypeDescription 1.3.6.1.4.1.207.8.42.8.34.12.3.1.1
Descriptive name of the AP image type.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..96)  

wsAPImageAvailabilityTable 1.3.6.1.4.1.207.8.42.8.34.12.4
This table lists the wireless controller stored AP code images.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPImageAvailabilityEntry

wsAPImageAvailabilityEntry 1.3.6.1.4.1.207.8.42.8.34.12.4.1
Each entry provides the code version of an AP image stored on the wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPImageAvailabilityEntry  

wsAPImageAvailability 1.3.6.1.4.1.207.8.42.8.34.12.4.1.1
The code version of each AP image stored on the wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

wsStatusTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.1
Flag to enable/disable SNMP traps for: WS Enabled, WS Disabled, WS Managed AP Database Full, WS Managed AP - AP Neighbor List Full, WS Managed AP - Client Neighbor List Full, WS - AP Failure List Full, RF Scan AP List Full, Client Association Database Full, Client Failure List Full.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsPeerWSTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.2
Flag to enable/disable SNMP traps for: Peer WS Discovered, Peer WS Failed, Peer WS Unknown Protocol Discovered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPStateTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.3
Flag to enable/disable SNMP traps for: WS Managed AP Discovered, WS Managed AP Failed, WS Managed AP Unknown Protocol Discovered.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPFailureTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.4
Flag to enable/disable SNMP traps for: WS AP Association Failure, WS AP Authentication Failure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsRogueAPTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.5
Flag to enable/disable SNMP traps for: RF Scan Rogue AP Detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsRFScanTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.6
Flag to enable/disable SNMP traps for: RF Scan New AP Detected, RF Scan New Client Detected. RF Scan Ad hoc Client Detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsClientStateTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.7
Flag to enable/disable SNMP traps for: Client Association Detected, Client Disassociation Detected, Client Roam Detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsWidsStatusMode 1.3.6.1.4.1.207.8.42.8.34.10.8
Flag to enable/disable SNMP traps for: This controller is Cluster Controller, Rogues are Present in the Network, RF Scan Rogue AP Detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsTspecTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.9
Flag to enable/disable SNMP traps for: TSPEC Client ACM Bandwidth Exceeded, TSPEC Client Traffic Unauthorized.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsClientFailureTrapMode 1.3.6.1.4.1.207.8.42.8.34.10.10
Flag to enable/disable SNMP traps for: Client Association Failure, Client Authentication Failure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsModeEnabled 1.3.6.1.4.1.207.8.42.8.34.0.1
A wsModeEnabled trap signifies that the SNMP entity, acting in an agent role, has detected that Wireless functionality on the device is enabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsModeDisabled 1.3.6.1.4.1.207.8.42.8.34.0.2
A wsModeDisabled trap signifies that the SNMP entity, acting in an agent role, has detected that Wireless functionality on the device is disabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsManagedAPDatabaseFull 1.3.6.1.4.1.207.8.42.8.34.0.3
A wsAPDatabaseFull trap signifies that the SNMP entity, acting in an agent role, has detected that AP Database is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsManagedAPNeighborAPListFull 1.3.6.1.4.1.207.8.42.8.34.0.4
A wsManagedAPNeighborListFull trap signifies that the SNMP entity, acting in an agent role, has detected that ManagedAP neighbor AP list is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsManagedAPNeighborClientListFull 1.3.6.1.4.1.207.8.42.8.34.0.5
A wsManagedAPNeighborClientListFull trap signifies that the SNMP entity, acting in an agent role, has detected that ManagedAP neighbor client list is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsAPFailureListFull 1.3.6.1.4.1.207.8.42.8.34.0.6
A wsAPFailureListFull trap signifies that the SNMP entity, acting in an agent role, has detected that AP failure list full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsRFScanAPListFull 1.3.6.1.4.1.207.8.42.8.34.0.7
A wsRFScanAPListFull trap signifies that the SNMP entity, acting in an agent role, has detected that RF scan AP list is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClientAssociationDatabaseFull 1.3.6.1.4.1.207.8.42.8.34.0.8
A wsClientAssociationDatabaseFull trap signifies that the SNMP entity, acting in an agent role, has detected that client association database is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPeerSwitchDiscovered 1.3.6.1.4.1.207.8.42.8.34.0.9
A wsPeerSwitchDiscovered trap signifies that the SNMP entity, acting in an agent role, has detected peer controller in the network.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPeerSwitchFailed 1.3.6.1.4.1.207.8.42.8.34.0.10
A wsPeerSwitchFailed trap signifies that the SNMP entity, acting in an agent role, has detected that peer controller connection failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPeerSwitchUnknownProtocol 1.3.6.1.4.1.207.8.42.8.34.0.11
A wsPeerSwitchUnknownProtocol trap signifies that the SNMP entity, acting in an agent role, has detected unknown protocol between wireless controller and peer controller communication.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsManagedAPDiscovered 1.3.6.1.4.1.207.8.42.8.34.0.12
A wsManagedAPDiscovered trap signifies that the SNMP entity, acting in an agent role, has detected the managed AP.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsManagedAPFailed 1.3.6.1.4.1.207.8.42.8.34.0.13
A wsManagedAPFailed trap signifies that the SNMP entity, acting in an agent role, has detected the failed AP.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsManagedAPUnknownProtocol 1.3.6.1.4.1.207.8.42.8.34.0.14
A wsManagedAPUnknownProtocol trap signifies that the SNMP entity, acting in an agent role, has detected the unknown protocol between wireless controller and managed AP communication.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsAPAssociationFailure 1.3.6.1.4.1.207.8.42.8.34.0.15
A wsAPAssociationFailure trap signifies that the SNMP entity, acting in an agent role, has detected that AP association failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsAPAuthenticationFailure 1.3.6.1.4.1.207.8.42.8.34.0.16
A wsAPAuthenticationFailure trap signifies that the SNMP entity, acting in an agent role, has detected that AP authentication failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsRFScanRogueAPDetected 1.3.6.1.4.1.207.8.42.8.34.0.17
A wsRFScanRogueAPDetected trap signifies that the SNMP entity, acting in an agent role, has detected Rogue AP through RF Scan.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsRFScanAPDetected 1.3.6.1.4.1.207.8.42.8.34.0.18
A wsRFScanAPDetected trap signifies that the SNMP entity, acting in an agent role, has detected AP through RF Scan.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsRFScanNewClientDetected 1.3.6.1.4.1.207.8.42.8.34.0.19
A wsRFScanNewClientDetected trap signifies that the SNMP entity, acting in an agent role, has detected new client through RF Scan.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClientAssociationDetected 1.3.6.1.4.1.207.8.42.8.34.0.20
A wsClientAssociationDetected trap signifies that the SNMP entity, acting in an agent role, has detected client association.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClientDisassociationDetected 1.3.6.1.4.1.207.8.42.8.34.0.21
A wsClientDisassociationDetected trap signifies that the SNMP entity, acting in an agent role, has detected client disassociation.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClientRoamDetected 1.3.6.1.4.1.207.8.42.8.34.0.22
A wsClientRoamDetected trap signifies that the SNMP entity, acting in an agent role, has detected client roaming.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClientAssociationFailure 1.3.6.1.4.1.207.8.42.8.34.0.23
A wsClientAssociationFailure trap signifies that the SNMP entity, acting in an agent role, has detected client association failure.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClientAuthenticationFailure 1.3.6.1.4.1.207.8.42.8.34.0.24
A wsAuthenticationFailure trap signifies that the SNMP entity, acting in an agent role, has detected client authentication failure.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsAdHocClientDetected 1.3.6.1.4.1.207.8.42.8.34.0.25
A wsAdHocClientDetected trap signifies that the SNMP entity, acting in an agent role, has detected Ad hoc client.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsWLANBandwidthUtilizationExceeded 1.3.6.1.4.1.207.8.42.8.34.0.26
A wsWLANBandwidthUtilizationExceeded trap signifies that the SNMP entity, acting in an agent role, has detected WLAN bandwidth utilization exceeding the limit.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsAdHocClientListFull 1.3.6.1.4.1.207.8.42.8.34.0.27
A wsAdHocClientListFull trap signifies that the SNMP entity, acting in an agent role, has detected that Ad hoc client database is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPeerSwitchConfigurationCommandReceived 1.3.6.1.4.1.207.8.42.8.34.0.28
A wsPeerSwitchConfigurationCommandReceived trap signifies that the SNMP entity, acting in an agent role, has received Configuration command from the peer controller in the network. The config mask received is also returned in the trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPeerSwitchManagedAPLimitExceeded 1.3.6.1.4.1.207.8.42.8.34.0.29
A wsPeerSwitchManagedAPLimitExceeded trap signifies that the SNMP entity, acting in an agent role, has detected that the Peer controller Managed AP database limit has exceeded.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPeerSwitchClientLimitExceeded 1.3.6.1.4.1.207.8.42.8.34.0.30
A wsPeerSwitchClientLimitExceeded trap signifies that the SNMP entity, acting in an agent role, has detected that the Peer controller Client database limit has exceeded.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClusterControllerElected 1.3.6.1.4.1.207.8.42.8.34.0.32
A wsClusterControllerElected trap signifies that the SNMP entity, acting in an agent role, has elected itself as Cluster Controller in the peer group.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsClusterMaxAPExceeded 1.3.6.1.4.1.207.8.42.8.34.0.33
A wsClusterMaxAPExceeded trap signifies that the SNMP entity, acting in an agent role, has detected that the managed APs in the network has exceeded.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsRoguesPresent 1.3.6.1.4.1.207.8.42.8.34.0.34
A wsRoguesPresent trap signifies that the SNMP entity, acting in an agent role, has detected one or more Rogues present in the network.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsDetectedClientListFull 1.3.6.1.4.1.207.8.42.8.34.0.35
A wsDetectedClientListFull trap signifies that the SNMP entity, acting in an agent role, has detected that Detected client database is full.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsRogueClientsPresent 1.3.6.1.4.1.207.8.42.8.34.0.36
A wsRogueClientsPresent trap signifies that the SNMP entity, acting in an agent role, has detected one or more Rogue Clients present in the network.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsChannelPlanAlgoComplete 1.3.6.1.4.1.207.8.42.8.34.0.37
A wsChannelAlgorithmComplete trap signifies that the SNMP entity, acting in an agent role, has detected channel algorithm complete event.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsPowerPlanAlgoComplete 1.3.6.1.4.1.207.8.42.8.34.0.38
A wsPowerAlgorithmComplete trap signifies that the SNMP entity, acting in an agent role, has detected power algorithm complete event.
Status: current Access: read-only
NOTIFICATION-TYPE    

wsLocallyManagedAPLimitExceeded 1.3.6.1.4.1.207.8.42.8.34.0.41
A wsLocallyManagedAPLimitExceeded trap signifies that the SNMP entity, acting in an agent role, has detected that the WS locally managed AP limit is exceeded.
Status: current Access: read-only
NOTIFICATION-TYPE    

tspecGlobal 1.3.6.1.4.1.207.8.42.8.34.17.1
OBJECT IDENTIFIER    

tspecSwitch 1.3.6.1.4.1.207.8.42.8.34.17.2
OBJECT IDENTIFIER    

tspecManagedAP 1.3.6.1.4.1.207.8.42.8.34.17.3
OBJECT IDENTIFIER    

tspecClient 1.3.6.1.4.1.207.8.42.8.34.17.4
OBJECT IDENTIFIER    

wsGlobalTspecStatus 1.3.6.1.4.1.207.8.42.8.34.17.1.1
OBJECT IDENTIFIER    

wsTspecTotalVoiceTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.1.1.1
Total number of traffic streams currently established for the voice access category. For a Cluster Controller, this value represents the entire cluster.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsTspecTotalVideoTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.1.1.2
Total number of traffic streams currently established for the video access category. For a Cluster Controller, this value represents the entire cluster.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsTspecTotalTrafficStreamClients 1.3.6.1.4.1.207.8.42.8.34.17.1.1.3
Total number of clients that currently possess one or more traffic streams in any access category. For a Cluster Controller, this value represents the entire cluster.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsTspecTotalTrafficStreamRoamingClients 1.3.6.1.4.1.207.8.42.8.34.17.1.1.4
Total number of roaming clients that currently possess one or more traffic streams in any access category. For a Cluster Controller, this value represents the entire cluster.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsGlobalTspecStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.17.1.2
This table contains global TSPEC statistics indexed on a per access category (AC) basis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsGlobalTspecStatisticsEntry

wsGlobalTspecStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1
Each entry contains global TSPEC statistics indexed on a per access category (AC) basis for the wireless controller. If this controller is a Cluster Controller, these object values represent the entire cluster.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsGlobalTspecStatisticsEntry  

wsTspecACIndex 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.1
Access category (AC) index used for referencing objects in the table row. Only those ACs that support mandatory admission control are available through this index. The currently supported AC index values are: 0 - Voice 1 - Video
Status: current Access: not-accessible
OBJECT-TYPE    
  TspecSuppAC  

wsTotalWLANTspecPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.2
Total packets received across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsTotalWLANTspecPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.3
Total packets transmitted across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsTotalWLANTspecBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.4
Total bytes received across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsTotalWLANTspecBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.5
Total bytes transmitted across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsTotalWLANTspecsAccepted 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.6
Total number of TSPECs accepted across all APs managed by this controller for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsTotalWLANTspecsRejected 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.7
Total number of TSPECs rejected across all APs managed by this controller for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsTotalWLANRoamingTspecsAccepted 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.8
Total number of TSPECs accepted from roaming clients across all APs managed by this controller for the specified access category. The value of this object is also included in the wsTotalWLANTspecsAccepted object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsTotalWLANRoamingTspecsRejected 1.3.6.1.4.1.207.8.42.8.34.17.1.2.1.9
Total number of TSPECs rejected from roaming clients across all APs managed by this controller for the specified access category. The value of this object is also included in the wsTotalWLANTspecsRejected object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsSwitchTspecStatusTable 1.3.6.1.4.1.207.8.42.8.34.17.2.1
This table contains TSPEC status parameters for peer controllers of the wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwitchTspecStatusEntry

wsSwitchTspecStatusEntry 1.3.6.1.4.1.207.8.42.8.34.17.2.1.1
Each entry describes the TPEC status parameters for a specific peer of the wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwitchTspecStatusEntry  

wsSwitchTspecTotalVoiceTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.2.1.1.1
Total number of traffic streams currently established for the voice access category for the specified controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsSwitchTspecTotalVideoTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.2.1.1.2
Total number of traffic streams currently established for the video access category for the specified controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsSwitchTspecTotalTrafficStreamClients 1.3.6.1.4.1.207.8.42.8.34.17.2.1.1.3
Total number of clients that currently possess one or more traffic streams in any access category for the specified controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsSwitchTspecTotalTrafficStreamRoamingClients 1.3.6.1.4.1.207.8.42.8.34.17.2.1.1.4
Total number of roaming clients that currently possess one or more traffic streams in any access category for the specified controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsSwitchTspecStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.17.2.2
This table contains WLAN TSPEC statistics on a per access category (AC) basis for each controller in the peer group. Only the Cluster Controller maintains entries for peer controllers. A non-Cluster Controller controller just keeps its local statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwitchTspecStatisticsEntry

wsSwitchTspecStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1
Each entry contains WLAN TSPEC statistics on a per access category (AC) basis for the specified wireless controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwitchTspecStatisticsEntry  

wsSwitchWLANTspecPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.1
Total packets received across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsSwitchWLANTspecPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.2
Total packets transmitted across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsSwitchWLANTspecBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.3
Total bytes received across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsSwitchWLANTspecBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.4
Total bytes transmitted across all APs managed by this controller for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsSwitchWLANTspecsAccepted 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.5
Total number of TSPECs accepted across all APs managed by this controller for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsSwitchWLANTspecsRejected 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.6
Total number of TSPECs rejected across all APs managed by this controller for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsSwitchWLANRoamingTspecsAccepted 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.7
Total number of TSPECs accepted from roaming clients across all APs managed by this controller for the specified access category. This value of this object is also included in the wsSwitchWLANTspecsAccepted object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsSwitchWLANRoamingTspecsRejected 1.3.6.1.4.1.207.8.42.8.34.17.2.2.1.8
Total number of TSPECs rejected from roaming clients across all APs managed by this controller for the specified access category. The value of this object is also included in the wsSwitchWLANTspecsRejected object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsManagedAPTspecStatusTable 1.3.6.1.4.1.207.8.42.8.34.17.3.1
This table contains TSPEC status parameters for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPTspecStatusEntry

wsManagedAPTspecStatusEntry 1.3.6.1.4.1.207.8.42.8.34.17.3.1.1
Each entry in this table contains TSPEC status parameters for a specific AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPTspecStatusEntry  

wsManagedAPTspecNumActiveTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.3.1.1.1
Indicates the current number of active traffic streams (TSs) for the specified access category of the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPTspecNumTrafficStreamClients 1.3.6.1.4.1.207.8.42.8.34.17.3.1.1.2
Indicates the current number of clients with at least one active traffic stream (TS) for the specified access category of the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPTspecNumTrafficStreamRoamingClients 1.3.6.1.4.1.207.8.42.8.34.17.3.1.1.3
Indicates the current number of roaming clients with at least one active traffic stream (TS) for the specified access category of the WS managed AP. The value of this object is also included in the wsManagedAPTspecNumTSClients object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPTspecStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.17.3.2
This table contains TSPEC statistics available for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPTspecStatisticsEntry

wsManagedAPTspecStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1
Each entry in this table contains TSPEC statistics for a specific AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPTspecStatisticsEntry  

wsManagedAPTspecPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.1
Total packets received by this AP on the wireless network for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPTspecPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.2
Total packets transmitted by this AP on the wireless network for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPTspecBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.3
Total bytes received by this AP on the wireless network for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPTspecBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.4
Total bytes transmitted by this AP on the wireless network for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPTspecsAccepted 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.5
Total number of TSPECs accepted by this AP on the wireless network for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsManagedAPTspecsRejected 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.6
Total number of TSPECs rejected by this AP on the wireless network for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsManagedAPRoamingTspecsAccepted 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.7
Total number of TSPECs accepted from roaming clients by an AP on the wireless network for the specified access category. This value of this object is also included in the wsManagedAPTspecsAccepted object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsManagedAPRoamingTspecsRejected 1.3.6.1.4.1.207.8.42.8.34.17.3.2.1.8
Total number of TSPECs rejected from roaming clients by an AP on the wireless network for the specified access category. This value of this object is also included in the wsManagedAPTspecsRejected object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsManagedAPRadioTspecStatusTable 1.3.6.1.4.1.207.8.42.8.34.17.3.3
This table contains TSPEC status parameters per radio interface for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPRadioTspecStatusEntry

wsManagedAPRadioTspecStatusEntry 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1
Each entry in this table contains TSPEC status parameters per radio interface for a specific AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPRadioTspecStatusEntry  

wsManagedAPRadioTspecOperStatus 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.1
Indicates the current operational status for the specified access category on this radio. If enabled(1), this access category operates in accordance with admission control mandatory (ACM) procedures.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wsManagedAPRadioTspecNumActiveTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.2
Indicates the current number of active traffic streams (TSs) for the specified access category on this radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioTspecNumTrafficStreamClients 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.3
Indicates the current number of clients with at least one active traffic stream (TS) for the specified access category on this radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioTspecNumTrafficStreamRoamingClients 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.4
Indicates the current number of roaming clients with at least one active traffic stream (TS) for the specified access category on this radio. The value of this object is also included in the wsManagedAPRadioTspecNumTSClients object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioTspecMediumTimeAdmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.5
Current sum of medium times allocated to clients with an active traffic stream (TS) belonging to the specified access category on this radio.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioTspecMediumTimeUnallocated 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.6
Amount of configured medium time not currently allocated for the specified access category on this radio that is available for both non-roaming and roaming clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioTspecMediumTimeRoamingUnallocated 1.3.6.1.4.1.207.8.42.8.34.17.3.3.1.7
Amount of configured medium time not currently allocated for the specified access category on this radio that is available for roaming clients only.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPRadioTspecStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.17.3.4
This table contains TSPEC statistics available per radio interface for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPRadioTspecStatisticsEntry

wsManagedAPRadioTspecStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.17.3.4.1
Each entry in this table contains TSPEC statistics per radio interface for a specific AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPRadioTspecStatisticsEntry  

wsManagedAPRadioTspecPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.17.3.4.1.1
Total packets received on this radio for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioTspecPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.4.1.2
Total packets transmitted on this radio for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioTspecBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.17.3.4.1.3
Total bytes received on this radio for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPRadioTspecBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.4.1.4
Total bytes transmitted on this radio for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPVAPTspecStatusTable 1.3.6.1.4.1.207.8.42.8.34.17.3.5
This table contains TSPEC status parameters for each VAP on the specified radio interface for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPVAPTspecStatusEntry

wsManagedAPVAPTspecStatusEntry 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1
Each entry in this table contains TSPEC status parameters for each VAP on the specified radio interface for a specific AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPVAPTspecStatusEntry  

wsManagedAPVAPTspecOperStatus 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.1
Indicates the current operational status for the specified access category on this VAP. If enabled(1), this access category operates in accordance with admission control mandatory (ACM) procedures.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wsManagedAPVAPTspecNumActiveTrafficStreams 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.2
Indicates the current number of active traffic streams (TSs) for the specified access category on this VAP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPTspecNumTrafficStreamClients 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.3
Indicates the current number of clients with at least one active traffic stream (TS) for the specified access category on this VAP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPTspecNumTrafficStreamRoamingClients 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.4
Indicates the current number of roaming clients with at least one active traffic stream (TS) for the specified access category on this VAP. The value of this object is also included in the wsManagedAPVAPTspecNumTSClients object.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPTspecMediumTimeAdmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.5
Current sum of medium times allocated to clients with an active traffic stream (TS) belonging to the specified access category on this VAP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPTspecMediumTimeUnallocated 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.6
Amount of configured medium time not currently allocated for the specified access category on this VAP that is available for both non-roaming and roaming clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPTspecMediumTimeRoamingUnallocated 1.3.6.1.4.1.207.8.42.8.34.17.3.5.1.7
Amount of configured medium time not currently allocated for the specified access category on this VAP that is available for roaming clients only.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsManagedAPVAPTspecStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.17.3.6
This table contains TSPEC statistics available for each VAP on the specified radio interface for all APs managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsManagedAPVAPTspecStatisticsEntry

wsManagedAPVAPTspecStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.17.3.6.1
Each entry in this table contains TSPEC statistics for each VAP on the specified radio for a specific AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsManagedAPVAPTspecStatisticsEntry  

wsManagedAPVAPTspecPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.17.3.6.1.1
Total packets received on this VAP for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPVAPTspecPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.6.1.2
Total packets transmitted on this VAP for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPVAPTspecBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.17.3.6.1.3
Total bytes received on this VAP for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsManagedAPVAPTspecBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.3.6.1.4
Total bytes transmitted on this VAP for all traffic streams belonging to the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientTsStatusTable 1.3.6.1.4.1.207.8.42.8.34.17.4.1
This table contains TSPEC traffic stream status parameters for clients currently associated with managed APs. Only clients possessing one or more active traffic streams appear in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientTsStatusEntry

wsAssociatedClientTsStatusEntry 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1
Each entry in this table contains TSPEC traffic stream status parameters for a specific client that is currently associated with the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientTsStatusEntry  

wsAssociatedClientTsTid 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.1
The traffic stream identifier (TID) indicated in the TSPEC that defines the traffic stream for the specified access category for the wireless client. Each traffic stream for a particular client must have a unique TID in the range 0-7, but per specification, any TID may map to any user priority and hence to any access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..7  

wsAssociatedClientTsAccessCategory 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.2
Access category (AC) of this client traffic stream. Only those ACs that support mandatory admission control are used. The currently supported AC values are: 0 - Voice 1 - Video
Status: current Access: not-accessible
OBJECT-TYPE    
  TspecSuppAC  

wsAssociatedClientTsDirection 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.3
The direction of the client traffic stream (TS) as indicated in the TSPEC. An uplink(1) TS monitors data traffic flowing from client station to AP, while a downlink(2) TS pertains to the opposite direction. A bidirectional(3) TS covers both directions and is treated as an uplink TS and downlink TS operating concurrently for the specified access category.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER uplink(1), downlink(2), bidirectional(3)  

wsAssociatedClientTsUserPriority 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.4
The user priority indicated in the TSPEC that defines the traffic stream for the specified access category for the wireless client. QoS Data frames to/from the client containing this user priority are categorized as belonging to the traffic stream, depending on direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientTsMediumTime 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.5
Indicates the amount of time this client is allowed to access the wireless medium each second for the specified access category through this traffic stream. This value is calculated by the AP based on various parameters supplied in the TSPEC add request from the client. The medium time is specified as the number of 32 microsecond time units the client is allowed to access the wireless network each second. This is referred to as units of 32 usec-per-sec and is generally treated as an average value, with any over-usage in one interval deducted from the alotted medium time for the next interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientTsExcessUsageEvents 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.6
The number of times the wireless client has appreciably exceeded the medium time established for its TSPEC. The actual measure of 'appreciably exceeded' is implementation-dependent, but it is not necessarily a single occurrence of exceeding the medium time for any given one second interval. Rather, this event may be indicated after repeated violations of the medium time over some measurement interval, and is intended as an heuristic to identify a wireless client whose TSPEC medium time may be set too low relative to its actual traffic stream requirements. This object reflects the number of excess usage events that have accumulated, but have not been reported, through the Trap Manager, with such reporting enabled by the wsTspecTrapMode object. Whenever a trap report is generated for this event, the value of this object restarts counting from zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAssociatedClientTsRoamingClientIndicator 1.3.6.1.4.1.207.8.42.8.34.17.4.1.1.7
A flag indicating whether this traffic stream was established by a wireless client that was considered to be a roaming client.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsAssociatedClientTsStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.17.4.2
This table contains TSPEC traffic stream statistics for clients currently associated with managed APs. Only clients possessing one or more active traffic streams appear in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAssociatedClientTsStatisticsEntry

wsAssociatedClientTsStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.17.4.2.1
Each entry in this table contains TSPEC traffic stream statistics for a specific client that is currently associated with the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAssociatedClientTsStatisticsEntry  

wsAssociatedClientTsPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.17.4.2.1.1
Total packets received from the client station for the traffic stream belonging to the specified access category. This object is only valid when the wsAssociatedClientTsDirection is either uplink(1) or bidirectional(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientTsPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.4.2.1.2
Total packets transmitted to the client station for the traffic stream belonging to the specified access category. This object is only valid when the wsAssociatedClientTsDirection is either downlink(2) or bidirectional(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientTsBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.17.4.2.1.3
Total bytes received from the client station for the traffic stream belonging to the specified access category. This object is only valid when the wsAssociatedClientTsDirection is either uplink(1) or bidirectional(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAssociatedClientTsBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.17.4.2.1.4
Total bytes transmitted to the client station for the traffic stream belonging to the specified access category. This object is only valid when the wsAssociatedClientTsDirection is either downlink(2) or bidirectional(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAPProvisioningTable 1.3.6.1.4.1.207.8.42.8.34.18.1
This table contains data for provisioning access points and also the AP provisioning status information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAPProvisioningEntry

wsAPProvisioningEntry 1.3.6.1.4.1.207.8.42.8.34.18.1.1
Each entry has parameters that indicate AP provisioned values and also parameters to configure new provisioning information.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAPProvisioningEntry  

wsAPProvMacAddress 1.3.6.1.4.1.207.8.42.8.34.18.1.1.1
MAC address of an AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsAPProvIPAddress 1.3.6.1.4.1.207.8.42.8.34.18.1.1.2
Network IP address of the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAPProvPrimarySwitchIP 1.3.6.1.4.1.207.8.42.8.34.18.1.1.3
Provisioned primary controller IP address on the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAPProvBackupSwitchIP 1.3.6.1.4.1.207.8.42.8.34.18.1.1.4
Provisioned backup controller IP address on the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAPProvMutualAuthMode 1.3.6.1.4.1.207.8.42.8.34.18.1.1.5
The mutual authentication mode configured in the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProvUnmanagedAPReprovMode 1.3.6.1.4.1.207.8.42.8.34.18.1.1.6
The configured AP re-provisioning mode when in unmanaged state in the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProvAge 1.3.6.1.4.1.207.8.42.8.34.18.1.1.7
Time since any information has been received from this AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  TimeTicks  

wsAPProvNewPrimarySwitchIP 1.3.6.1.4.1.207.8.42.8.34.18.1.1.8
The IP address of the primary controller which the adminstrator wants to provision the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAPProvNewBackupSwitchIP 1.3.6.1.4.1.207.8.42.8.34.18.1.1.9
The IP address of the backup controller which the administrator wants to provision the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAPProvNewProfileId 1.3.6.1.4.1.207.8.42.8.34.18.1.1.10
Profile ID to be configured in the local Valid AP database of the primary and backup controllers.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..16  

wsAPProvCommand 1.3.6.1.4.1.207.8.42.8.34.18.1.1.11
This parameter triggers the AP provisioning process for this AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(0), initiate(1)  

wsAPProvStatus 1.3.6.1.4.1.207.8.42.8.34.18.1.1.12
Status of the most recently issued AP provisioning command.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), success(3), in-progress(4), provisioning-rejected(5), timed-out(6)  

wsAPProvCertProfileTxStatus 1.3.6.1.4.1.207.8.42.8.34.18.1.1.13
Status of the last AP profile and X.509 certificate distribution to primary and backup controllers.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-started(1), success(2), failed(3)  

wsAPProvEntryPurge 1.3.6.1.4.1.207.8.42.8.34.18.1.1.14
This is an action object. Setting this object to enable will delete the AP entry if it is unmanaged. Reads on this object will always return disabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAPProvisioningInitiateAll 1.3.6.1.4.1.207.8.42.8.34.18.2
Start provisioning of all the APs in the database.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(0), initiate(1)  

wsAPProvisioningDeleteAll 1.3.6.1.4.1.207.8.42.8.34.18.3
Delete all unmanaged AP provisioning entries
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsNetworkExchangeCertificates 1.3.6.1.4.1.207.8.42.8.34.18.4
Trigger the wireless controllers and APs to exchange X.509 certificates. This command can be triggered only when mutual authentication is already enabled on the network.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(0), initiate(1)  

wsSwitchProvIPAddress 1.3.6.1.4.1.207.8.42.8.34.18.5
IP address of the controller from which this controller obtains the provisioning information.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsSwitchProvStatus 1.3.6.1.4.1.207.8.42.8.34.18.6
Status of controller provisioning activity.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), in-progress(3), provisioning-failed(4), connection-failed(5), success(6)  

wsSwitchCertReqTarget 1.3.6.1.4.1.207.8.42.8.34.18.7
IP address of the wireless controller from which this controller requests an X.509 certificate
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsSwitchCertReqStatus 1.3.6.1.4.1.207.8.42.8.34.18.8
Status of X.509 certificate request status.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), in-progress(3), invalid-ip(4), timed-out(5), success(6)  

wsSwitchProvisioningCommand 1.3.6.1.4.1.207.8.42.8.34.18.9
This parameter triggers the controller provisioning with the controller specified in the Provisioning controller IP address
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(0), initiate(1)  

wsSwitchCertReqCommand 1.3.6.1.4.1.207.8.42.8.34.18.10
This parameter initiates the X.509 certificate request from the controller specified in the Certificate Request Target.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(0), initiate(1)  

wsWDSAPGroupTable 1.3.6.1.4.1.207.8.42.8.34.19.1
The following
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSAPGroupEntry

wsWDSAPGroupEntry 1.3.6.1.4.1.207.8.42.8.34.19.1.1
Each entry
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSAPGroupEntry  

wsWDSAPGroupId 1.3.6.1.4.1.207.8.42.8.34.19.1.1.1
Unique WDS Group Id for each entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsWDSAPGroupName 1.3.6.1.4.1.207.8.42.8.34.19.1.1.2
AP configuration profile name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsWDSAPGroupSpanningTree 1.3.6.1.4.1.207.8.42.8.34.19.1.1.3
This varible allows the spanning tree mode enabling or disabling in a Managed AP Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsWDSAPGroupPassword 1.3.6.1.4.1.207.8.42.8.34.19.1.1.4
Indicates password to be used to form WDS links among the APs in a Managed AP Group. If password is configured, read on this object will return '*****'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8..63)  

wsWDSAPGroupRowStatus 1.3.6.1.4.1.207.8.42.8.34.19.1.1.5
This variable is used to create or delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsWDSAPGroupAPTable 1.3.6.1.4.1.207.8.42.8.34.19.2
List of the AP MAC addresses in the AP Group
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSAPGroupAPEntry

wsWDSAPGroupAPEntry 1.3.6.1.4.1.207.8.42.8.34.19.2.1
Per Group Group Id and MAC address of the AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSAPGroupAPEntry  

wsWDSAPGroupAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.19.2.1.1
AP MAC address in the WDS AP Group
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsWDSAPGroupAPStpPriority 1.3.6.1.4.1.207.8.42.8.34.19.2.1.2
AP's STP priority in the WDS AP Group
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..61440  

wsWDSAPGroupAPEntryRowStatus 1.3.6.1.4.1.207.8.42.8.34.19.2.1.3
This variable is used to create or delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsWDSAPLinkTable 1.3.6.1.4.1.207.8.42.8.34.19.3
This table contains the WDS AP Links created on the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSAPLinkEntry

wsWDSAPLinkEntry 1.3.6.1.4.1.207.8.42.8.34.19.3.1
Each entry in this table contains parameters for the WDS link of WDS AP Group in the Wireless network.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSAPLinkEntry  

wsWDSAPLinkSourceMacAddr 1.3.6.1.4.1.207.8.42.8.34.19.3.1.1
MAC Address of one End-Point of WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsWDSAPLinkSourceRadio 1.3.6.1.4.1.207.8.42.8.34.19.3.1.2
Radio Number of the WDS Link End-Point on the Source AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsWDSAPLinkDestMacAddr 1.3.6.1.4.1.207.8.42.8.34.19.3.1.3
MAC Address of another End-Point of WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsWDSAPLinkDestRadio 1.3.6.1.4.1.207.8.42.8.34.19.3.1.4
Radio Number of the WDS Link End-Point on the Destination AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsWDSAPLinkPathCost 1.3.6.1.4.1.207.8.42.8.34.19.3.1.5
Spanning Tree path cost for the WDS AP Link.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

wsWDSAPLinkRowStatus 1.3.6.1.4.1.207.8.42.8.34.19.3.1.6
This variable is used to create or delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsWDSAPGroupStatusTable 1.3.6.1.4.1.207.8.42.8.34.19.4
This table contains status parameters for the WDS APs created on the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSAPGroupStatusEntry

wsWDSAPGroupStatusEntry 1.3.6.1.4.1.207.8.42.8.34.19.4.1
Each entry in this table contains status parameters for the WDS Group configured in WDS group database.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSAPGroupStatusEntry  

wsWDSConfigAPCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.1
Number of APs configured by the Administrator in this WDS AP Group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

wsWDSConnectedAPCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.2
Number of APs managed by the controller that are members of this WDS AP Group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

wsWDSRootAPCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.3
Number of Root APs managed by the controller that are members of this WDS AP Group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

wsWDSSatelliteAPCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.4
Number of Satellite APs managed by the controller that are members of this WDS AP Group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4  

wsWDSAPRootBridge 1.3.6.1.4.1.207.8.42.8.34.19.4.1.5
MAC Address of the device elected as the Spanning Tree Root Bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsWDSAPRootDeviceType 1.3.6.1.4.1.207.8.42.8.34.19.4.1.6
The type of device elected as the Spanning Tree Root bridge.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), root-ap(1), satellite-ap(2), external-device(3)  

wsWDSConfigWDSLinkCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.7
Number of configured bidirectional links in the WDS AP Group.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..6  

wsWDSDetectedWDSLinkCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.8
Number of WDS links detected in the system.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..6  

wsWDSBlockedWDSLinkCount 1.3.6.1.4.1.207.8.42.8.34.19.4.1.9
Number of WDS links blocked by the spanning tree protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..6  

wsWDSGroupNewPassword 1.3.6.1.4.1.207.8.42.8.34.19.4.1.10
This Password is sent to all controllers and APs when the Change-Password command is initiadted by the administrator for this WDS Group. When passwod is configured this object will always return '*****'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(8..63)  

wsWDSGroupChangePasswdStart 1.3.6.1.4.1.207.8.42.8.34.19.4.1.11
This action object is used to: - start - Start the WDS Group password change for the peer controllers and the managed APs. - Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsWDSGroupChangePasswdStatus 1.3.6.1.4.1.207.8.42.8.34.19.4.1.12
Status of the last invocation of the password change protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-started(1), requested(2), success(3), invalid-password(4), in-progress(5), timed-out(6), failed(7)  

wsWDSAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.19.5
This table contains status parameters for the WDS APs created on the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSAPStatusEntry

wsWDSAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.19.5.1
Each entry in this table contains status parameters for the WDS AP configured in WDS group database.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSAPStatusEntry  

wsWDSAPMacAddr 1.3.6.1.4.1.207.8.42.8.34.19.5.1.1
MAC Address of the WDS AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsWDSAPConnectionStatus 1.3.6.1.4.1.207.8.42.8.34.19.5.1.2
Flag indicating whether the AP is currently being managed by one of the Wireless controllers in the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-connected(0), connected(1)  

wsWDSAPSatelliteMode 1.3.6.1.4.1.207.8.42.8.34.19.5.1.3
Flag indicating whether the AP is a Satellite AP connected via WDS link or a Root AP connected via the wire to the campus network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), wired(1), satellite(2)  

wsWDSAPSTPRootMode 1.3.6.1.4.1.207.8.42.8.34.19.5.1.4
Flag indicating whether the AP is the root of the spanning tree.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER not-stp-root(0), stp-root(1)  

wsWDSAPSTPCost 1.3.6.1.4.1.207.8.42.8.34.19.5.1.5
Spanning Tree Path Cost to the root.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsWDSAPEthPortSTPStatus 1.3.6.1.4.1.207.8.42.8.34.19.5.1.6
Spanning Tree Status of the Ethernet Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER disabled(0), forwarding(1), learning(2), listening(3), blocking(4)  

wsWDSAPEthPortMode 1.3.6.1.4.1.207.8.42.8.34.19.5.1.7
Ethernet Port Mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wsWDSAPEthPortLinkState 1.3.6.1.4.1.207.8.42.8.34.19.5.1.8
Link State of Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

wsWDSLinkStatusTable 1.3.6.1.4.1.207.8.42.8.34.19.6
This table contains status parameters for the WDS Links created on the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSLinkStatusEntry

wsWDSLinkStatusEntry 1.3.6.1.4.1.207.8.42.8.34.19.6.1
Each entry in this table contains status parameters for the WDS link created on the Wireless network.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSLinkStatusEntry  

wsWDSSourceMacAddr 1.3.6.1.4.1.207.8.42.8.34.19.6.1.1
MAC Address of one End-Point of WDS link.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsWDSSourceRadio 1.3.6.1.4.1.207.8.42.8.34.19.6.1.2
Radio Number of the WDS Link End-Point on the Source AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsWDSDestMacAddr 1.3.6.1.4.1.207.8.42.8.34.19.6.1.3
MAC Address of another End-Point of WDS link.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

wsWDSDestRadio 1.3.6.1.4.1.207.8.42.8.34.19.6.1.4
Radio Number of the WDS Link End-Point on the Destination AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

wsWDSLinkSourceEndPointDetected 1.3.6.1.4.1.207.8.42.8.34.19.6.1.5
Flag indicating whether AP specified by the Destination MAC detected the AP specified by the source MAC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-detected(0), detected(1)  

wsWDSLinkDestEndPointDetected 1.3.6.1.4.1.207.8.42.8.34.19.6.1.6
Flag indicating whether AP specified by the Source MAC detected the AP specified by the Destination MAC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-detected(0), detected(1)  

wsWDSLinkSourceSTPState 1.3.6.1.4.1.207.8.42.8.34.19.6.1.7
Spanning Tree State of the link on the source AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER disabled(0), forwarding(1), learning(2), listening(3), blocking(4)  

wsWDSLinkDestSTPState 1.3.6.1.4.1.207.8.42.8.34.19.6.1.8
Spanning Tree State of the link on the destination AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER disabled(0), forwarding(1), learning(2), listening(3), blocking(4)  

wsWDSLinkAggregationMode 1.3.6.1.4.1.207.8.42.8.34.19.6.1.9
When parallel links are defined between two APs, this parameter indicates whether this link is part of the aggregation link pair.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-aggregated(0), aggregated(1)  

wsWDSLinkStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.19.7
This table contains statistics available for each AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsWDSLinkStatisticsEntry

wsWDSLinkStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.19.7.1
Each entry in this table contain statistics available for each AP managed by the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsWDSLinkStatisticsEntry  

wsWDSLinkSourceAPPktsSent 1.3.6.1.4.1.207.8.42.8.34.19.7.1.1
Total number of packets transmitted by the Source AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkSourceAPBytesSent 1.3.6.1.4.1.207.8.42.8.34.19.7.1.2
Total number of bytes transmitted by the source AP on the link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkSourceAPPktsRcvd 1.3.6.1.4.1.207.8.42.8.34.19.7.1.3
Total number of packets received by the Source AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkSourceAPBytesRcvd 1.3.6.1.4.1.207.8.42.8.34.19.7.1.4
Total number of bytes received by the Source AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkDestAPPktsSent 1.3.6.1.4.1.207.8.42.8.34.19.7.1.5
Total number of packets transmitted by the Destination AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkDestAPBytesSent 1.3.6.1.4.1.207.8.42.8.34.19.7.1.6
Total number of bytes transmitted by the Destination AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkDestAPPktsRcvd 1.3.6.1.4.1.207.8.42.8.34.19.7.1.7
Total number of packets received by the Destination AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSLinkDestAPBytesRcvd 1.3.6.1.4.1.207.8.42.8.34.19.7.1.8
Total Number of bytes received by the Destination AP on the WDS link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsWDSGroupConfigRequestAction 1.3.6.1.4.1.207.8.42.8.34.19.8
This action object is used to: - start - Start the WDS Group config push to the peer controllers and the managed APs. - Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsDevLocBldngTable 1.3.6.1.4.1.207.8.42.8.34.20.1
This table contains data for configuration parameters for device location.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDevLocBldngEntry

wsDevLocBldngEntry 1.3.6.1.4.1.207.8.42.8.34.20.1.1
Each entry in this table contains building parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDevLocBldngEntry  

wsDevLocBldngNum 1.3.6.1.4.1.207.8.42.8.34.20.1.1.1
Indicates building number for a particular building.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

wsDevLocBldngDesc 1.3.6.1.4.1.207.8.42.8.34.20.1.1.2
The building description for a particular building.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

wsDevLocFlrCount 1.3.6.1.4.1.207.8.42.8.34.20.1.1.3
Indicates floor count for a particular building.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..20  

wsDevLocApCount 1.3.6.1.4.1.207.8.42.8.34.20.1.1.4
Indicates AP count for a particular building.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..192  

wsDevLocBldngRowStatus 1.3.6.1.4.1.207.8.42.8.34.20.1.1.5
This variable is used to create and delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsDevLocBldngFlrTable 1.3.6.1.4.1.207.8.42.8.34.20.2
This table contains data for configuration parameters for device location building and floor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDevLocBldngFlrEntry

wsDevLocBldngFlrEntry 1.3.6.1.4.1.207.8.42.8.34.20.2.1
Each entry in this table contains building floor parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDevLocBldngFlrEntry  

wsDevLocBldngFlrNum 1.3.6.1.4.1.207.8.42.8.34.20.2.1.1
Indicates floor number for a particular building.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..20  

wsDevLocBldngFlrDesc 1.3.6.1.4.1.207.8.42.8.34.20.2.1.2
The floor description for a particular floor.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

wsDevLocBldngFlrApCount 1.3.6.1.4.1.207.8.42.8.34.20.2.1.3
Indicates AP count for a particular building-floor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..192  

wsDevLocFlrRowStatus 1.3.6.1.4.1.207.8.42.8.34.20.2.1.4
This variable is used to create and delete entries in the table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsDevLocManagedApTable 1.3.6.1.4.1.207.8.42.8.34.20.3
This table contains data for configuration parameters for device location building, floor and AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsDevLocManagedApEntry

wsDevLocManagedApEntry 1.3.6.1.4.1.207.8.42.8.34.20.3.1
Each entry in this table contains building floor parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsDevLocManagedApEntry  

wsDevLocManagedApMac 1.3.6.1.4.1.207.8.42.8.34.20.3.1.1
The MAC address of the AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsDevLocMeasurementUnit 1.3.6.1.4.1.207.8.42.8.34.20.3.1.2
Measurement Units in Meters/Feet.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER meters(1), feet(2)  

wsDevLocManagedApXCoord 1.3.6.1.4.1.207.8.42.8.34.20.3.1.3
This indicates the X-coordinate of the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -3000..3000  

wsDevLocManagedApYCoord 1.3.6.1.4.1.207.8.42.8.34.20.3.1.4
This indicates the Y-coordinate of the AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -3000..3000  

wsDevLocManagedApRowStatus 1.3.6.1.4.1.207.8.42.8.34.20.3.1.5
This variable is used to create and delete entries in the table. AP entry should be created with Measurement Unit and XY-Coordinates.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

wsOnDemandTrigger 1.3.6.1.4.1.207.8.42.8.34.20.4
OBJECT IDENTIFIER    

wsOnDemandTriggerGlobalStatus 1.3.6.1.4.1.207.8.42.8.34.20.5
OBJECT IDENTIFIER    

wsOnDemandTriggerFloorStatus 1.3.6.1.4.1.207.8.42.8.34.20.6
OBJECT IDENTIFIER    

wsOnDemandTriggerDeviceType 1.3.6.1.4.1.207.8.42.8.34.20.4.1
Type of the device to be located.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ap(1), client(2)  

wsOnDemandTriggerDeviceMACAddress 1.3.6.1.4.1.207.8.42.8.34.20.4.2
AP or Client MAC address whose location the Administrator want to find.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsOnDemandTriggerBuildingNumber 1.3.6.1.4.1.207.8.42.8.34.20.4.3
Building number in which to search for the target device. Please note that only configured buildings will be accepted. Buildings with no configured floors are not accepted. Value 0 is used to indicate search in all of the buildings in the system. Value 0 is accepted only if there exists any configured building-floor. Setting building to 0 will automatically reset floor value to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..8  

wsOnDemandTriggerFloorNumber 1.3.6.1.4.1.207.8.42.8.34.20.4.4
Floor Number on which to search. Please note that only configured floor numbers for the specified building will be accepted. Value 0 is used to indicate search in all of the floors in the specified building. Value 0 is accepted only if there exists any configured floor in the current building.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..20  

wsOnDemandTriggerUseRadios 1.3.6.1.4.1.207.8.42.8.34.20.4.5
This object Indicates if the network should use only sentry radios to do the search or both sentry and operational mode radios.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sentry(1), sentryAndOperational(2)  

wsOnDemandTriggerStatus 1.3.6.1.4.1.207.8.42.8.34.20.4.6
Status of the last invoked On-Demand location procedure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInProgress(1), inProgress(2)  

wsOnDemandTriggerNumOfAPs 1.3.6.1.4.1.207.8.42.8.34.20.4.7
Number of managed APs that are available for locating the target device in the building/floor/sentry scope specified by the administrator.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerStart 1.3.6.1.4.1.207.8.42.8.34.20.4.8
Trigger new On-Demand location procedure for the device specified in the configured building and floors. If On-Demand procedure is already running then setting this parameter has no effect.A read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), start(1)  

wsOnDemandTriggerGlobalStatusDeviceType 1.3.6.1.4.1.207.8.42.8.34.20.5.1
Flag indicating whether the device is an AP or a Wireless Client.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ap(1), client(2)  

wsOnDemandTriggerGlobalStatusDeviceMACAddress 1.3.6.1.4.1.207.8.42.8.34.20.5.2
AP or Client MAC address whose location was requested.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsOnDemandTriggerGlobalStatusBuildingNumber 1.3.6.1.4.1.207.8.42.8.34.20.5.3
Building number in which to search for the target device was done. Value 0 is used to indicate search in all of the buildings in the system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..8  

wsOnDemandTriggerGlobalStatusFloorNumber 1.3.6.1.4.1.207.8.42.8.34.20.5.4
Floor Number on which the search was done. Value 0 is used to indicate search in all of the floors in the specified building.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..20  

wsOnDemandTriggerGlobalStatusUsedRadios 1.3.6.1.4.1.207.8.42.8.34.20.5.5
Flag indicating whether the network used only sentry radios to do the search or both sentry and operational mode radios.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sentry(1), sentryAndOperational(2)  

wsOnDemandTriggerGlobalStatusCurrentStatus 1.3.6.1.4.1.207.8.42.8.34.20.5.6
Current status of the last invocation of the On-Demand Location Procedure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(1), inProgress(2), deviceLocated(3), deviceNotLocated(4), noAPsAvailable(5)  

wsOnDemandTriggerGlobalStatusSearchTime 1.3.6.1.4.1.207.8.42.8.34.20.5.7
Time since the On-Demand Location triggered.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsOnDemandTriggerGlobalStatusNumOfLocatorAPs 1.3.6.1.4.1.207.8.42.8.34.20.5.8
Number of managed APs that were used for locating the target device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerGlobalStatusNumOfDetectedAPs 1.3.6.1.4.1.207.8.42.8.34.20.5.9
Number of managed APs that detected the device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerGlobalStatusNumOfDetectedBuildings 1.3.6.1.4.1.207.8.42.8.34.20.5.10
Number of buildings where managed APs detected the target device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerGlobalStatusNumOfDetectedFloors 1.3.6.1.4.1.207.8.42.8.34.20.5.11
Number of building floors where managed APs detected the target device. Floors from different buildings may be included in this status.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerGlobalStatusHighestSignalFoundBuilding 1.3.6.1.4.1.207.8.42.8.34.20.5.12
Building number in which the target device was detected by a managed AP with the highest RSSI. Value of 0 for this object indicates that device is not detected in any of the buildings.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerGlobalStatusHighestSignalFoundFloor 1.3.6.1.4.1.207.8.42.8.34.20.5.13
Floor number on which the target device was detected by a managed AP with the highest RSSI. Value of 0 for this object indicates that device is not detected in any of the floors.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerFloorStatusTable 1.3.6.1.4.1.207.8.42.8.34.20.6.1
This table contains the location record for each building floor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsOnDemandTriggerFloorStatusEntry

wsOnDemandTriggerFloorStatusEntry 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1
Location record. Each entry contains location status of the target device with respect to building anf floor numbers.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsOnDemandTriggerFloorStatusEntry  

wsOnDemandTriggerFloorStatusBuildingNum 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.1
Building number.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerFloorStatusFloorNum 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.2
Floor number
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerFloorStatusDeviceFound 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.3
Flag indicating whether the device is found on this floor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notFound(1), found(2)  

wsOnDemandTriggerFloorStatusNumOfAPs 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.4
Number of APs located on this floor that detected the device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerFloorStatusSolutionType 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.5
Flag indicating whether the probability map is a circle around the managed AP, or the solution is an X,Y coordinate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSolution(1), circle(2), point(3)  

wsOnDemandTriggerFloorStatusXCoordinate 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.6
X-axis offset. The parameter is applicable to the Circle and Point solution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

wsOnDemandTriggerFloorStatusYCoordinate 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.7
Y-axis offset. The parameter is applicable to the Circle and Point solution.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

wsOnDemandTriggerFloorStatusCircleRadius 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.8
For the Circle solution this parameter represents the radius from the X,Y coordinate where the device is most likely to be located. For the Point solution this value is not applicable and is set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

wsOnDemandTriggerFloorStatusSigma 1.3.6.1.4.1.207.8.42.8.34.20.6.1.1.9
The standard deviation for the location. The parameter is applicable to Circle and Point solutions. For the Circle solution the Sigma represents the offset from Circle Radius. For the Point solution the sigma represents the radius from the X,Y coordinate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

wsTriangulationLocStatusTable 1.3.6.1.4.1.207.8.42.8.34.20.7
This table contains data for triangulation location and status information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsTriangulationLocStatusEntry

wsTriangulationLocStatusEntry 1.3.6.1.4.1.207.8.42.8.34.20.7.1
Each entry has parameters that indicate triangulation location status values.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsTriangulationLocStatusEntry  

wsTriangLocMacAddress 1.3.6.1.4.1.207.8.42.8.34.20.7.1.1
MAC address of an AP or Client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsTriangLocDataType 1.3.6.1.4.1.207.8.42.8.34.20.7.1.2
This parameter indicates whether the location data is present for this device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-present(0), present(1)  

wsTriangLocStatus 1.3.6.1.4.1.207.8.42.8.34.20.7.1.3
The status of the last iteration of the location computation algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-executed(1), success(2), failure(3)  

wsTriangLocDeviceType 1.3.6.1.4.1.207.8.42.8.34.20.7.1.4
This parameter indicates device type whether AP or Client.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ap(1), client(2)  

wsTriangLocAge 1.3.6.1.4.1.207.8.42.8.34.20.7.1.5
Time since the last successful location computation.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsTriangLocBldng 1.3.6.1.4.1.207.8.42.8.34.20.7.1.6
Indicates building number in which device is detected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

wsTriangLocFlr 1.3.6.1.4.1.207.8.42.8.34.20.7.1.7
Indicates floor number in which device is detected.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..20  

wsTriangLocXCoord 1.3.6.1.4.1.207.8.42.8.34.20.7.1.8
This indicates the X axis offset of the device from some arbitrary 0,0 point on the building floor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -3000..3000  

wsTriangLocYCoord 1.3.6.1.4.1.207.8.42.8.34.20.7.1.9
This indicates the Y axis offset of the device from some arbitrary 0,0 point on the building floor.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -3000..3000  

wsAuthenticatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.1
This table contains status parameters of clients that are currently associated with managed APs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAuthenticatedClientStatusEntry

wsAuthenticatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.1.1
Each entry in this table contain client status parameters assocaited with the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAuthenticatedClientStatusEntry  

wsAuthenticatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.1.1.1
Authenticated client MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientTunnelIpAddress 1.3.6.1.4.1.207.8.42.8.34.21.1.1.2
Indicates network IP address of the client station, 0.0.0.0 indicates unknown. Tunnel IP subnet is present only for clients authenticated with tunneled VAPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

wsAuthenticatedClientUserName 1.3.6.1.4.1.207.8.42.8.34.21.1.1.3
Indicates user name of the client that have authenticated via 802.1x, clients on networks with other security modes will not have a user name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAuthenticatedClientSSID 1.3.6.1.4.1.207.8.42.8.34.21.1.1.4
Indicates the network on which the client is connected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

wsAuthenticatedClientVLAN 1.3.6.1.4.1.207.8.42.8.34.21.1.1.5
If client is on VAP using VLAN data forwarding mode, indicates current assigned VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4094  

wsAuthenticatedClientStatus 1.3.6.1.4.1.207.8.42.8.34.21.1.1.6
This object indicates client's status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER authenticated(1), associated(2), disassociated(3)  

wsAuthenticatedClientTxDataRate 1.3.6.1.4.1.207.8.42.8.34.21.1.1.7
Indicates the data rate, AP will actually support in setting up communications with client stations represented by a count from 2 - 1200, corresponding to data rates in multiples of 500 kbit/s from 1 Mbit/s to 600 Mbit/s. Supported Data Rate Mbps 2 1 4 2 11 5.5 12 6 18 9 and so on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..1200  

wsAuthenticatedClientInactivePeriod 1.3.6.1.4.1.207.8.42.8.34.21.1.1.8
For a current association, period of time that the AP has not seen any traffic for the client.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAuthenticatedClientDisassociateAction 1.3.6.1.4.1.207.8.42.8.34.21.1.1.9
This is an action object. Setting this object to start will initiate the disassociation of associated client. Read on this object will always return none.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), start(2)  

wsAuthenticatedClientAge 1.3.6.1.4.1.207.8.42.8.34.21.1.1.10
Indicates time since the controller has received new data for this client.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAuthenticatedClientAssociatingSwitch 1.3.6.1.4.1.207.8.42.8.34.21.1.1.11
This object indicates whether the client is associated to an AP managed by this controller or peer-controller.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local-switch(1), peer-switch(2)  

wsAuthenticatedClientSwitchMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.1.1.12
MAC address of the WS associating the client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientSwitchIpAddress 1.3.6.1.4.1.207.8.42.8.34.21.1.1.13
IP address of the WS associating the client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsAuthenticatedClientDot11nCapable 1.3.6.1.4.1.207.8.42.8.34.21.1.1.14
Flag indicating whether this client is capable of 802.11n operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsAuthenticatedClientStbcCapable 1.3.6.1.4.1.207.8.42.8.34.21.1.1.15
Flag indicating whether this client is capable of Space Time Block Code (STBC) operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsAuthenticatedClientDistTunnelStatus 1.3.6.1.4.1.207.8.42.8.34.21.1.1.16
Indicates whether L2 Distributed Tunneling is Enabled or Disabled
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAuthenticatedClientDistTunnelRoamStatus 1.3.6.1.4.1.207.8.42.8.34.21.1.1.17
Indicates whether the client is using the distrubuted tunnel or not. Also indicates if it is a roamed client or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER associated(0), home(1)  

wsAuthenticatedClientDistTunnelHomeAPMac 1.3.6.1.4.1.207.8.42.8.34.21.1.1.18
Indicates MAC Address of the client's Home AP. Here the client should be associated with the network on which the L2 Distributed Tunneling is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientDistTunnelAssocAPMac 1.3.6.1.4.1.207.8.42.8.34.21.1.1.19
MAC Address of the client's Association AP to which the client has roamed to.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.1.1.20
MAC Address of the AP to which client is Authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientBSSID 1.3.6.1.4.1.207.8.42.8.34.21.1.1.21
BSSID of the VAP to which client is associated.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientRadioInterface 1.3.6.1.4.1.207.8.42.8.34.21.1.1.22
Indicates the radio interface on which client is associated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAuthenticatedClientChannel 1.3.6.1.4.1.207.8.42.8.34.21.1.1.23
Indicates channel for associated client entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..165  

wsAuthenticatedClientNwTime 1.3.6.1.4.1.207.8.42.8.34.21.1.1.24
Indicates time since this client first authenticated with the network.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

wsAuthenticatedClientIpAddress 1.3.6.1.4.1.207.8.42.8.34.21.1.1.25
Indicates network IPv4 address of the client station detetecd through ARP snooping, 0.0.0.0 indicates unknown.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsAuthenticatedClientNetBiosName 1.3.6.1.4.1.207.8.42.8.34.21.1.1.26
NetBios Name of the client.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

wsAuthenticatedClientRRMSupported 1.3.6.1.4.1.207.8.42.8.34.21.1.1.27
Indicates if the Radio Resource Management (RRM) portion of the IEEE 802.11k standard is supported by client and RRM is enabled is on the AP Profile. Value 2 indicates the client supports RRM portion and RRM Mode is not enabled on AP Profile. Value 3 indicates client doesnot support RRM
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enabled(1), supported(2), unsupported(3)  

wsAuthenticatedClientRRMLocationReportSupported 1.3.6.1.4.1.207.8.42.8.34.21.1.1.28
Indicates if the client can support RRM location report requests.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAuthenticatedClientRRMBeaconTableMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.21.1.1.29
Indicates if the client can detect APs via RRM beacon table reports.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAuthenticatedClientRRMBeaconActiveMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.21.1.1.30
Indicates if the client supports active scan capability.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAuthenticatedClientRRMBeaconPassiveMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.21.1.1.31
Indicates if the client supports passive scan capability.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAuthenticatedClientRRMChannelLoadMeasurementSupported 1.3.6.1.4.1.207.8.42.8.34.21.1.1.32
Indicates if the client supports RRM channel load measurement.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER supported(1), unsupported(2)  

wsAuthenticatedClientDot11acCapable 1.3.6.1.4.1.207.8.42.8.34.21.1.1.33
Flag indicating whether this client is capable of 802.11ac operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

wsAuthenticatedClientStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.21.2
This table contains statistics available for each client associated to a WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAuthenticatedClientStatisticsEntry

wsAuthenticatedClientStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.21.2.1
Each entry in this table contain statistics available for each client associated a WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAuthenticatedClientStatisticsEntry  

wsAuthenticatedClientPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.2.1.1
Total packets received by a managed AP from the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.21.2.1.2
Total bytes received by a managed AP from the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.2.1.3
Total packets transmitted by a managed AP to the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.2.1.4
Total bytes transmitted by a managed AP to the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientDuplicatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.2.1.5
Total duplicate packets received from the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientFragmentedPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.2.1.6
Total fragmented packets received from the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientFragmentedPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.2.1.7
Total fragmented packets transmitted to the client station.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientTransmitRetryCount 1.3.6.1.4.1.207.8.42.8.34.21.2.1.8
Indicates number of times transmits to client station succeeded after one or more retries.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientTransmitRetryFailedCount 1.3.6.1.4.1.207.8.42.8.34.21.2.1.9
Number of times transmits to client station failed after one or more retries.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.21.2.1.10
Total packets dropped in the receive direction by a managed AP from the client station. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.21.2.1.11
Total bytes dropped in the receive direction by a managed AP from the client station. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.21.2.1.12
Total packets dropped in the transmit direction by a managed AP to the client station. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.21.2.1.13
Total bytes dropped in the transmit direction by a managed AP to the client station. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientTsViolatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.2.1.14
Number of packets received by the AP from a client station that are in excess of the client's alotted traffic stream (TS) uplink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientTsViolatePktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.2.1.15
Number of packets transmitted by the AP to a client station that are in excess of the client's alotted traffic stream (TS) downlink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientNeighborManagedAPStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.3
This table is maintained to lookup all WS managed APs detected, client can see in its RF area.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAuthenticatedClientNeighborManagedAPStatusEntry

wsAuthenticatedClientNeighborManagedAPStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.3.1
Each entry in this table contain WS managed APs that can be seen by client in its RF area.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAuthenticatedClientNeighborManagedAPStatusEntry  

wsAuthenticatedClientStationMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.3.1.1
The Ethernet address of a client station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientNeighborWSManagedAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.3.1.2
The Ethernet address of a WS managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientNeighborWSManagedAPRadioInterface 1.3.6.1.4.1.207.8.42.8.34.21.3.1.3
The radio interface of Managed AP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

wsAuthenticatedClientStationDiscoveryReason 1.3.6.1.4.1.207.8.42.8.34.21.3.1.4
Indicates the client status with respect to the Managed AP it is refering. One or more flags can be enabled at the same time.
Status: current Access: read-only
OBJECT-TYPE    
  BITS none(0), rfscan-discovered(1), neighbor-ap-associated(2), current-ap-associated(3), probe-request-discovered(4), ad-hoc-rogue(5), associated-to-peer-ap(6)  

wsVAPAuthenticatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.4
This table is maintained to lookup clients associated to a specific VAP on a WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsVAPAuthenticatedClientStatusEntry

wsVAPAuthenticatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.4.1
Each entry in this table contain clients associated to each VAP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsVAPAuthenticatedClientStatusEntry  

wsAuthenticatedVAPMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.4.1.1
The Ethernet address assigned to a VAP to which the client is associated.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsVAPAuthenticatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.4.1.2
The Ethernet address of associated client station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsSSIDAuthenticatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.5
This table is maintained to lookup all clients associated to a particular network.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSSIDAuthenticatedClientStatusEntry

wsSSIDAuthenticatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.5.1
Each entry in this table contain clients associated to a particular network.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSSIDAuthenticatedClientStatusEntry  

wsAuthenticatedSSID 1.3.6.1.4.1.207.8.42.8.34.21.5.1.1
Indicates the network on which the client is connected.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

wsSSIDAuthenticatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.5.1.2
The Ethernet address of the client station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsSwitchAuthenticatedClientStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.6
This table is maintained to lookup clients associated to the APs managed by the specific controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwitchAuthenticatedClientStatusEntry

wsSwitchAuthenticatedClientStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.6.1
Each entry in this table contain client associated to each controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwitchAuthenticatedClientStatusEntry  

wsAuthenticatedClientSwitchIPAddress 1.3.6.1.4.1.207.8.42.8.34.21.6.1.1
IP address of the WS associating the client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

wsSwitchAuthenticatedClientMacAddress 1.3.6.1.4.1.207.8.42.8.34.21.6.1.2
Ethernet address of the associated client station.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

wsAuthenticatedClientQosStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.7
This table contains client QoS status parameters of clients that are currently associated with managed APs. These objects represent the actual operational status values in effect for the clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAuthenticatedClientQosStatusEntry

wsAuthenticatedClientQosStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.7.1
Each entry in this table contains client QoS status parameters for a client associated with the WS managed AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAuthenticatedClientQosStatusEntry  

wsAuthenticatedClientQosBandwidthLimitDown 1.3.6.1.4.1.207.8.42.8.34.21.7.1.1
Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client, thus controlling the maximum receive rate from the AP for this wireless client. This parameter is specified in bits-per-second (bps). The displayed value represents the actual bandwidth rate in use for the client, which may differ from the configured value since the AP rounds down to the nearest 64000 bps. A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAuthenticatedClientQosBandwidthLimitUp 1.3.6.1.4.1.207.8.42.8.34.21.7.1.2
Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP, thus controlling the maximum send rate from this wireless client to the AP. This parameter is specified in bits-per-second (bps). The displayed value represents the actual bandwidth rate in use for the client, which may differ from the configured value since the AP rounds down to the nearest 64000 bps. A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAuthenticatedClientQosAccessControlDownType 1.3.6.1.4.1.207.8.42.8.34.21.7.1.3
Access list type used for the wireless down (outbound) direction from the AP to this client. The wsAuthenticatedClientQosAccessControlDownName object identifies the access list.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAuthenticatedClientQosAccessControlDownName 1.3.6.1.4.1.207.8.42.8.34.21.7.1.4
Name of the access list in use in accordance with the wsAuthenticatedClientQosAccessControlDownType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosAccessControlUpType 1.3.6.1.4.1.207.8.42.8.34.21.7.1.5
Access list type used for the wireless up (inbound) direction from this client to the AP. The wsAuthenticatedClientQosAccessControlUpName object identifies the access list.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAuthenticatedClientQosAccessControlUpName 1.3.6.1.4.1.207.8.42.8.34.21.7.1.6
Name of the access list in use in accordance with the wsAuthenticatedClientQosAccessControlUpType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosDiffservPolicyDownType 1.3.6.1.4.1.207.8.42.8.34.21.7.1.7
DiffServ policy type used for the wireless down (outbound) direction from the AP to this client. The wsAuthenticatedClientQosDiffservPolicyDownName object identifies the DiffServ policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAuthenticatedClientQosDiffservPolicyDownName 1.3.6.1.4.1.207.8.42.8.34.21.7.1.8
Name of the DiffServ policy in use in accordance with the wsAuthenticatedClientQosDiffservPolicyDownType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosDiffservPolicyUpType 1.3.6.1.4.1.207.8.42.8.34.21.7.1.9
DiffServ policy type used for the wireless up (inbound) direction from this client to the AP. The wsAuthenticatedClientQosDiffservPolicyUpName object identifies the DiffServ policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAuthenticatedClientQosDiffservPolicyUpName 1.3.6.1.4.1.207.8.42.8.34.21.7.1.10
Name of the DiffServ policy in use in accordance with the wsAuthenticatedClientQosDiffservPolicyUpType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosOperStatus 1.3.6.1.4.1.207.8.42.8.34.21.7.1.11
Designates the AP quality-of-service operational status for this wireless client. This represents the combined states of the wsApClientQosMode object and the wsNetworkClientQosMode object for the wireless network to which this client is associated.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wsAuthenticatedClientSessionStatisticsTable 1.3.6.1.4.1.207.8.42.8.34.21.8
This table contains statistics available for each client associated to a WS managed AP, but accumulated for the duration of the entire WLAN session, inclusive of client roaming.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAuthenticatedClientSessionStatisticsEntry

wsAuthenticatedClientSessionStatisticsEntry 1.3.6.1.4.1.207.8.42.8.34.21.8.1
Each entry in this table contain statistics available for each client associated a WS managed AP, but accumulated for the duration of the entire WLAN session, inclusive of client roaming.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAuthenticatedClientSessionStatisticsEntry  

wsAuthenticatedClientSessionPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.8.1.1
Total packets received by managed APs from the client station throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionBytesRecvd 1.3.6.1.4.1.207.8.42.8.34.21.8.1.2
Total bytes received by managed APs from the client station throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.8.1.3
Total packets transmitted by managed APs to the client station throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionBytesTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.8.1.4
Total bytes transmitted by managed APs to the client station throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionDuplicatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.8.1.5
Total duplicate packets received from the client station throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientSessionFragmentedPktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.8.1.6
Total fragmented packets received from the client station. throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientSessionFragmentedPktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.8.1.7
Total fragmented packets transmitted to the client station throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientSessionTransmitRetryCount 1.3.6.1.4.1.207.8.42.8.34.21.8.1.8
Indicates number of times transmits to client station succeeded after one or more retries throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientSessionTransmitRetryFailedCount 1.3.6.1.4.1.207.8.42.8.34.21.8.1.9
Number of times transmits to client station failed after one or more retries throughout the duration of the current WLAN session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientSessionPktsRecvDropped 1.3.6.1.4.1.207.8.42.8.34.21.8.1.10
Total packets dropped in the receive direction by managed APs from the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionBytesRecvDropped 1.3.6.1.4.1.207.8.42.8.34.21.8.1.11
Total bytes dropped in the receive direction by managed APs from the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless up (inbound) direction from client to AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionPktsTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.21.8.1.12
Total packets dropped in the transmit direction by managed APs to the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionBytesTransmitDropped 1.3.6.1.4.1.207.8.42.8.34.21.8.1.13
Total bytes dropped in the transmit direction by managed APs to the client station throughout the duration of the current WLAN session. This is due to client QoS actions affecting the wireless down (outbound) direction from AP to client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter64  

wsAuthenticatedClientSessionTSViolatePktsRecvd 1.3.6.1.4.1.207.8.42.8.34.21.8.1.14
Number of packets received by managed APs from a client station throughout the duration of the current WLAN session that are in excess of the client's alotted traffic stream (TS) uplink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientSessionTSViolatePktsTransmitted 1.3.6.1.4.1.207.8.42.8.34.21.8.1.15
Number of packets transmitted by managed APs to a client station throughout the duration of the current WLAN session that are in excess of the client's alotted traffic stream (TS) downlink bandwidth, or are for an access category requiring admission control to which the client station has not been admitted.
Status: current Access: not-accessible
OBJECT-TYPE    
  Counter32  

wsAuthenticatedClientQosCachedStatusTable 1.3.6.1.4.1.207.8.42.8.34.21.9
This table contains cached client QoS status parameters of clients that are currently associated with managed APs. These objects represent values that were retrieved from a RADIUS server for this client. See the wsAuthenticatedClientQosStatusTable for the current set of operational values in use for this client.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsAuthenticatedClientQosCachedStatusEntry

wsAuthenticatedClientQosCachedStatusEntry 1.3.6.1.4.1.207.8.42.8.34.21.9.1
Each entry in this table contains client QoS cached status parameters for a client associated with the WS managed AP. Only those parameters successfully retrieved from a RADIUS server via 802.1X authentication on behalf of a wireless client are displayed.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsAuthenticatedClientQosCachedStatusEntry  

wsAuthenticatedClientQosCachedBandwidthLimitDown 1.3.6.1.4.1.207.8.42.8.34.21.9.1.1
Maximum bandwidth rate allowed for the wireless down (outbound) direction from AP to client, thus controlling the maximum receive rate from the AP for this wireless client. This parameter is specified in bits-per-second (bps). A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAuthenticatedClientQosCachedBandwidthLimitUp 1.3.6.1.4.1.207.8.42.8.34.21.9.1.2
Maximum bandwidth rate allowed for the wireless up (inbound) direction from client to AP, thus controlling the maximum send rate from this wireless client to the AP. This parameter is specified in bits-per-second (bps). A value of 0 indicates bandwidth limiting is disabled in this direction for the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

wsAuthenticatedClientQosCachedAccessControlDownType 1.3.6.1.4.1.207.8.42.8.34.21.9.1.3
Access list type used for the wireless down (outbound) direction from the AP to this client. The wsAuthenticatedClientQosCachedAccessControlDownName object identifies the access list.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAuthenticatedClientQosCachedAccessControlDownName 1.3.6.1.4.1.207.8.42.8.34.21.9.1.4
Name of the access list in use in accordance with the wsAuthenticatedClientQosCachedAccessControlDownType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosCachedAccessControlUpType 1.3.6.1.4.1.207.8.42.8.34.21.9.1.5
Access list type used for the wireless up (inbound) direction from this client to the AP. The wsAuthenticatedClientQosCachedAccessControlUpName object identifies the access list.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), ip(2), mac(3), ipv6(4)  

wsAuthenticatedClientQosCachedAccessControlUpName 1.3.6.1.4.1.207.8.42.8.34.21.9.1.6
Name of the access list in use in accordance with the wsAuthenticatedClientQosCachedAccessControlUpType as follows: none(1) - This object is not displayed. ip(2) - This specifies an IP access list number in the range 1-199, or an IP access list name as defined by the aclName object in the aclTable in the FASTPATH-QOS-ACL-MIB. mac(3) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid MAC access list name, as defined by the aclMacName object in the FASTPATH-QOS-ACL-MIB. ipv6(4) - This is an alphanumeric string from 1-31 characters, beginning with a letter. This must be a valid IPV6 access list name, as defined by the aclIpv6Name object in the FASTPATH-QOS-ACL-MIB. Note that numbered IP access lists are displayed here using a character string notation instead of an integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosCachedDiffservPolicyDownType 1.3.6.1.4.1.207.8.42.8.34.21.9.1.7
DiffServ policy type used for the wireless down (outbound) direction from the AP to this client. The wsAuthenticatedClientQosCachedDiffservPolicyDownName object identifies the DiffServ policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAuthenticatedClientQosCachedDiffservPolicyDownName 1.3.6.1.4.1.207.8.42.8.34.21.9.1.8
Name of the DiffServ policy in use in accordance with the wsAuthenticatedClientQosCachedDiffservPolicyDownType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

wsAuthenticatedClientQosCachedDiffservPolicyUpType 1.3.6.1.4.1.207.8.42.8.34.21.9.1.9
DiffServ policy type used for the wireless up (inbound) direction from this client to the AP. The wsAuthenticatedClientQosCachedDiffservPolicyUpName object identifies the DiffServ policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER none(1), in(2)  

wsAuthenticatedClientQosCachedDiffservPolicyUpName 1.3.6.1.4.1.207.8.42.8.34.21.9.1.10
Name of the DiffServ policy in use in accordance with the wsAuthenticatedClientQosCachedDiffservPolicyUpType as follows: none(1) - This object is not displayed. in(2) - This specifies a DiffServ policy name, as defined by the agentDiffServPolicyName object in the FASTPATH-QOS-DIFFSERV-PRIVATE-MIB. Note that only DiffServ policy defintions of type 'in' are supported for wireless client QoS operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)