AS-2000

File: AS-2000.mib (96668 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC-1215

Imported symbols

enterprises IpAddress Counter
TimeTicks OBJECT-TYPE TRAP-TYPE

Defined Types

DisplayString  
OCTET STRING    

PhysAddress  
OCTET STRING    

PsWlanIfEntry  
SEQUENCE    
  pliWlanIfIndex INTEGER
  pliWlanIfNetworkName DisplayString
  pliWlanIfMACAddress PhysAddress
  pliWlanIfMediumReservation INTEGER
  pliWlanIfTransmitRate INTEGER
  pliWlanIfOperatingFrequency INTEGER
  pliWlanIfAPDensity INTEGER
  pliWlanIfClosedSystem INTEGER
  pliWlanIfAllowedTransmitRates INTEGER
  pliWlanIfRegulatoryDomainList OCTET STRING
  pliWlanIfAllowedOperatingFrequencies INTEGER
  pliWlanIfCapabilityOptions INTEGER
  pliWlanIfProfileCode INTEGER

PsSNMPAccessTableEntry  
SEQUENCE    
  managerIndex INTEGER
  managerIPAddress IpAddress
  managerSubnetMask IpAddress
  managerStatus INTEGER

PsPPPMACIPMappingTableEntry  
SEQUENCE    
  mACIPIndex INTEGER
  mACAddress PhysAddress
  iPAddress IpAddress
  comment DisplayString
  entryStatus INTEGER

PsPPPIPRangeTableEntry  
SEQUENCE    
  pPPIPIndex INTEGER
  startIPAddress IpAddress
  endIPAddress IpAddress
  width INTEGER
  iPComment DisplayString
  wtatus INTEGER

RadiusServerEntry  
SEQUENCE    
  radiusServerIndex INTEGER
  radiusServerType INTEGER
  radiusServerAddress IpAddress
  radiusServerDestPortAuth INTEGER
  radiusServerDestPortAcct INTEGER
  radiusClientAccessRequests Counter
  radiusClientAccessRetransmissions Counter
  radiusClientAccessAccepts Counter
  radiusClientAccessChallenges Counter
  radiusClientMalformedAccessResponses Counter
  radiusClientAuthenticationBadAuthenticators Counter
  radiusClientAccessRejects Counter
  radiusClientTimeouts Counter
  radiusClientAccountingRequests Counter
  radiusClientAccountingRetransmissions Counter
  radiusClientAccountingResponses Counter
  radiusClientAccountingBadAuthenticators Counter
  radiusServerSharedSecret DisplayString
  radiusServerEnabled INTEGER
  radiusServerResponseTime INTEGER
  radiusServerMaximumRetransmission INTEGER

PsASClientEntry  
SEQUENCE    
  psPPPSessionId INTEGER
  psIpxClientNetworkNumber OCTET STRING
  psIpxClientMAC PhysAddress
  psIpxClientStatus INTEGER
  psASClientSessionUpTime TimeTicks
  psASClientPacketsIn Counter
  psASClientPacketsOut Counter

OriLinkTestTableEntry  
SEQUENCE    
  oriLinkTestTableIndex INTEGER
  oriLinkTestInProgress INTEGER
  oriLinkTestStationName DisplayString
  oriLinkTestMACAddress PhysAddress
  oriLinkTestStationProfile INTEGER
  oriLinkTestOurCurSignalLevel INTEGER
  oriLinkTestOurCurNoiseLevel INTEGER
  oriLinkTestOurCurSNR INTEGER
  oriLinkTestOurMinSignalLevel INTEGER
  oriLinkTestOurMinNoiseLevel INTEGER
  oriLinkTestOurMinSNR INTEGER
  oriLinkTestOurMaxSignalLevel INTEGER
  oriLinkTestOurMaxNoiseLevel INTEGER
  oriLinkTestOurMaxSNR INTEGER
  oriLinkTestOurLowFrameCount INTEGER
  oriLinkTestOurStandardFrameCount INTEGER
  oriLinkTestOurMediumFrameCount INTEGER
  oriLinkTestOurHighFrameCount INTEGER
  oriLinkTestHisCurSignalLevel INTEGER
  oriLinkTestHisCurNoiseLevel INTEGER
  oriLinkTestHisCurSNR INTEGER
  oriLinkTestHisMinSignalLevel INTEGER
  oriLinkTestHisMinNoiseLevel INTEGER
  oriLinkTestHisMinSNR INTEGER
  oriLinkTestHisMaxSignalLevel INTEGER
  oriLinkTestHisMaxNoiseLevel INTEGER
  oriLinkTestHisMaxSNR INTEGER
  oriLinkTestHisLowFrameCount INTEGER
  oriLinkTestHisStandardFrameCount INTEGER
  oriLinkTestHisMediumFrameCount INTEGER
  oriLinkTestHisHighFrameCount INTEGER
  oriLinkTestInterface INTEGER
  oriLinkTestRadioType INTEGER

Defined Values

lucent 1.3.6.1.4.1.1751
OBJECT IDENTIFIER    

mibs 1.3.6.1.4.1.1751.2
OBJECT IDENTIFIER    

orinoco 1.3.6.1.4.1.1751.2.4
OBJECT IDENTIFIER    

as2000 1.3.6.1.4.1.1751.2.4.3
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.1751.1
OBJECT IDENTIFIER    

orinocoProducts 1.3.6.1.4.1.1751.1.4
OBJECT IDENTIFIER    

as2000Product 1.3.6.1.4.1.1751.1.4.4
OBJECT IDENTIFIER    

orinocoInterface 1.3.6.1.4.1.1751.2.4.3.3
OBJECT IDENTIFIER    

orinocoSNMPSetup 1.3.6.1.4.1.1751.2.4.3.4
OBJECT IDENTIFIER    

orinocoPPPSetup 1.3.6.1.4.1.1751.2.4.3.5
OBJECT IDENTIFIER    

orinocoAgent 1.3.6.1.4.1.1751.2.4.3.6
OBJECT IDENTIFIER    

radius 1.3.6.1.4.1.1751.2.4.3.7
OBJECT IDENTIFIER    

orinocoShimECPSetup 1.3.6.1.4.1.1751.2.4.3.8
OBJECT IDENTIFIER    

orinocoDiagnostics 1.3.6.1.4.1.1751.2.4.3.10
OBJECT IDENTIFIER    

orinocoIAPP 1.3.6.1.4.1.1751.2.4.3.11
OBJECT IDENTIFIER    

orinocoIPX 1.3.6.1.4.1.1751.2.4.3.12
OBJECT IDENTIFIER    

orinocoLinkTest 1.3.6.1.4.1.1751.2.4.3.13
OBJECT IDENTIFIER    

accessServerTraps 1.3.6.1.4.1.1751.2.4.3.15
OBJECT IDENTIFIER    

orinocoPHY 1.3.6.1.4.1.1751.2.4.3.3.2
OBJECT IDENTIFIER    

orinocoDriver 1.3.6.1.4.1.1751.2.4.3.3.4
OBJECT IDENTIFIER    

pliSystemName 1.3.6.1.4.1.1751.2.4.3.3.2.1
The sysName of the Access Server. This may be used for diagnostic purposes. This name will be the same as the sysName of the system group of MIB II
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

psWlanIfTable 1.3.6.1.4.1.1751.2.4.3.3.2.2
The table contains the information about the wavelan interfaces present in the Access Server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PsWlanIfEntry

psWlanIfEntry 1.3.6.1.4.1.1751.2.4.3.3.2.2.1
The entry in the wavelan interfac table. Described next.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PsWlanIfEntry  

pliWlanIfIndex 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.1
A unique value for each interface. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pliWlanIfNetworkName 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.2
The network name of this wavelan interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

pliWlanIfMACAddress 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.3
The MAC address of the wavelan card present in this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

pliWlanIfMediumReservation 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.4
The medium reservation value. The range is 0 - 2347. Default is 2347 - means disabled. Medium reservation specifies the number of octets in a message above which a RTS/CTS handshake is performed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2347  

pliWlanIfTransmitRate 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.5
The transmit rate of this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pliWlanIfOperatingFrequency 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.6
The RF channel that the Access Server is working on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..14  

pliWlanIfAPDensity 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.7
The AP density in the region.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pliWlanIfClosedSystem 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.8
This flag identifies whether the Access Server will accept associate requests in this interface, from AS-Clients having a network name of 'ANY'. The Access Server should always be a closed station and such requests should always be rejected. This flag is provided for diagnostic purposes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pliWlanIfAllowedTransmitRates 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.9
This variables reflects the transmit rates that the wavelan card supports
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pliWlanIfRegulatoryDomainList 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.10
This variables reflects the regulatory domain the wavelan card belongs to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

pliWlanIfAllowedOperatingFrequencies 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.11
This variables reflects the RF channels that the wavelan card supports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pliWlanIfCapabilityOptions 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.12
The capabilities of the card. Indicates the support of features like WEP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pliWlanIfProfileCode 1.3.6.1.4.1.1751.2.4.3.3.2.2.1.13
The varible conprises of a vendor indication (Lucent or an OEM customer) and a capability indication (eg. bronze or gold).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pliDriverName 1.3.6.1.4.1.1751.2.4.3.3.4.1
The driver name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

pliDriverVersion 1.3.6.1.4.1.1751.2.4.3.3.4.2
The driver's version number. This is a text string including the major and minor release number, and, optionally, the patch level: 'mm.nn.pp', where mm = major release number nn = point release number pp = optional patch number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

psSNMPReadPassword 1.3.6.1.4.1.1751.2.4.3.4.1
The password for reading object values from the agent.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString  

psSNMPReadWritePassword 1.3.6.1.4.1.1751.2.4.3.4.2
The password for reading and modifying object values from the agent.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString  

psSNMPTrapHostIPAddress 1.3.6.1.4.1.1751.2.4.3.4.3
The IP address of the host to which traps should be sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psSNMPTrapHostPassword 1.3.6.1.4.1.1751.2.4.3.4.4
The password sent with the trap to enable the management station to ignore unsolicited traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

psSNMPManagerCount 1.3.6.1.4.1.1751.2.4.3.4.5
The number of management stations that have been authorised to manage this Access Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

psSNMPAccessTable 1.3.6.1.4.1.1751.2.4.3.4.6
The table containing the information about the managers authorised to manage this Access Server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PsSNMPAccessTableEntry

psSNMPAccessTableEntry 1.3.6.1.4.1.1751.2.4.3.4.6.1
The entry in the SNMP access table. Described next.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PsSNMPAccessTableEntry  

managerIndex 1.3.6.1.4.1.1751.2.4.3.4.6.1.1
Management station identification number. Is the index for the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

managerIPAddress 1.3.6.1.4.1.1751.2.4.3.4.6.1.2
IP address of the management station.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

managerSubnetMask 1.3.6.1.4.1.1751.2.4.3.4.6.1.3
The IP subnet mask. Used to grant access to a complete subnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

managerStatus 1.3.6.1.4.1.1751.2.4.3.4.6.1.4
Whether the manager is enabled or disabled. Used to delete the unwanted entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), delete(2)  

psSNMPInBadManagers 1.3.6.1.4.1.1751.2.4.3.4.7
The no of attempts to manage this Access Server by unauthorised managers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psTestSNMPReadWritePassword 1.3.6.1.4.1.1751.2.4.3.4.8
The password for reading and modifying object values from the agent can be verified by setting this.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString  

psPPPIPAddressAssignmentType 1.3.6.1.4.1.1751.2.4.3.5.1
This identifies whether the IP addresses assigned to the AS-Clients are obtained through APM (address pool manager), through DHCP or through the RADIUS server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPNoOfMACIPMappingEntries 1.3.6.1.4.1.1751.2.4.3.5.2
The number of static mapping entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

psPPPMACIPMappingTable 1.3.6.1.4.1.1751.2.4.3.5.3
This table contains the static mapping of MAC addresses to IP addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PsPPPMACIPMappingTableEntry

psPPPMACIPMappingTableEntry 1.3.6.1.4.1.1751.2.4.3.5.3.1
The entry of the asPPPMACIPMappingTable Described below.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PsPPPMACIPMappingTableEntry  

mACIPIndex 1.3.6.1.4.1.1751.2.4.3.5.3.1.1
This is the index for the mappping table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mACAddress 1.3.6.1.4.1.1751.2.4.3.5.3.1.2
This is the MAC address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

iPAddress 1.3.6.1.4.1.1751.2.4.3.5.3.1.3
The IP address corresponding to the MAC address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

comment 1.3.6.1.4.1.1751.2.4.3.5.3.1.4
The comment for this entry, maybe the PC's owner.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

entryStatus 1.3.6.1.4.1.1751.2.4.3.5.3.1.5
Whether the entry is enabled or disabled. Used to delete the unwanted entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), delete(2)  

psPPPKeepAliveInterval 1.3.6.1.4.1.1751.2.4.3.5.4
The keep alive interval to be notified to the PPP layer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPNoOfKeepAliveTimeouts 1.3.6.1.4.1.1751.2.4.3.5.5
The maximum number of timeouts before the session is torn down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPPrimaryDNSIPAddress 1.3.6.1.4.1.1751.2.4.3.5.6
The IP address of the primary DNS server in the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psPPPSecondaryDNSIPAddress 1.3.6.1.4.1.1751.2.4.3.5.7
The IP address of the secondary DNS server in the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psPPPMaxNoOfUsers 1.3.6.1.4.1.1751.2.4.3.5.8
The maximum no of clients permitted to connect to this Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPCHAPStatus 1.3.6.1.4.1.1751.2.4.3.5.9
This variable indicates the status of CHAP in the Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPCHAPPriority 1.3.6.1.4.1.1751.2.4.3.5.10
This variable indicates the priority of CHAP among all authentictaion protocols enabled on the Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPPAPStatus 1.3.6.1.4.1.1751.2.4.3.5.11
This variable indicates the status of PAP in the Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPPAPPriority 1.3.6.1.4.1.1751.2.4.3.5.12
This variable indicates the priority of PAP among all authentictaion protocols enabled on the Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psPPPPrimaryNBNSIPAddress 1.3.6.1.4.1.1751.2.4.3.5.13
The IP address of the Primary NBNS server in the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psPPPSecondaryNBNSIPAddress 1.3.6.1.4.1.1751.2.4.3.5.14
The IP address of the Secondary NBNS server in the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psPPPIPRangeTable 1.3.6.1.4.1.1751.2.4.3.5.15
This table contains the static mapping of MAC addresses to IP addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PsPPPIPRangeTableEntry

psPPPIPRangeTableEntry 1.3.6.1.4.1.1751.2.4.3.5.15.1
The entry of the psPPPIPRangeTable. Described below.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PsPPPIPRangeTableEntry  

pPPIPIndex 1.3.6.1.4.1.1751.2.4.3.5.15.1.1
This is the index for the IP range table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

startIPAddress 1.3.6.1.4.1.1751.2.4.3.5.15.1.2
This is the staring IP address of this range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

endIPAddress 1.3.6.1.4.1.1751.2.4.3.5.15.1.3
This is the ending IP address of this range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

width 1.3.6.1.4.1.1751.2.4.3.5.15.1.4
This is the withd of the range (no of addresses).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

status 1.3.6.1.4.1.1751.2.4.3.5.15.1.5
The status of the entry, whether to be used or not used. Setting this to delete will remove this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), delete(3)  

iPComment 1.3.6.1.4.1.1751.2.4.3.5.15.1.6
The comment for this entry may be the PC owner.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

psPPPSessionIdleTimeOut 1.3.6.1.4.1.1751.2.4.3.5.16
The varible indicates the Session Idle time out.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..36000  

psVersion 1.3.6.1.4.1.1751.2.4.3.6.1
The version of the Access Server software currently execuing. Would be text string including the major and minor release number, and, optionally, the patch level: 'mm.nn.pp', where mm = major release number nn = point release number pp = optional patch number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

psIPAddress 1.3.6.1.4.1.1751.2.4.3.6.2
The IP address to be assigned to the Access Server (to change from factory fitted IP address).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psSubnetMask 1.3.6.1.4.1.1751.2.4.3.6.3
The subnet mask of the Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psDefaultGateway 1.3.6.1.4.1.1751.2.4.3.6.4
The default gateway for the Access Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psIPAddressType 1.3.6.1.4.1.1751.2.4.3.6.5
This can be DHCP/BOOTP(dynamic) or assigned by User via CLI or AS Manager(static). The IP address of the Access Server will be assigned based on this.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psAdministrativeState 1.3.6.1.4.1.1751.2.4.3.6.6
The administrative state of the substation, can be Up or Down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psTFTPIPAddress 1.3.6.1.4.1.1751.2.4.3.6.7
The IP address of the TFTP server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

psTFTPFilename 1.3.6.1.4.1.1751.2.4.3.6.8
The filename of the image in the TFTP server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

psTFTPOperation 1.3.6.1.4.1.1751.2.4.3.6.9
The operation to be done, can be upload or download.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

psReboot 1.3.6.1.4.1.1751.2.4.3.6.10
This variable must be set to reboot the Access Server. The value is the number of seconds to wait to do a reboot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psSecondsToAdminDown 1.3.6.1.4.1.1751.2.4.3.6.11
The count of seconds to go before the administrative state of the Access Server is made down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psContactEmail 1.3.6.1.4.1.1751.2.4.3.6.12
The textual identification of the contact person for this managed node, together with information on how to contact this person.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

psBSPBootloaderVersion 1.3.6.1.4.1.1751.2.4.3.6.13
This object represents the BSP/Bootloader version that is currently stored in the access server device..
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

psTelnetSesssions 1.3.6.1.4.1.1751.2.4.3.6.14
This object is used to enable or disable telnet access and to specify the number of active telnet sessions. When this object is set to 0, telnet access is disabled. When this object is set to something greater than 0, then it specifies the maximum number of active telnet sessions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

psTelnetPassword 1.3.6.1.4.1.1751.2.4.3.6.15
Password to access Access Server from Telenet.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString  

psTelnetPort 1.3.6.1.4.1.1751.2.4.3.6.16
The TCP/IP port for Access Server Telenet daemon.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psTelnetTimeout 1.3.6.1.4.1.1751.2.4.3.6.17
Telnet inactivity timeout in minutes. The default value is 15 minutes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

psTelnetLoginTimeout 1.3.6.1.4.1.1751.2.4.3.6.18
Telnet login timeout in seconds. The default value is 30 seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

psSerialBaudRate 1.3.6.1.4.1.1751.2.4.3.6.19
Serial interface baud rate. The default value is 9600
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psSerialDataBits 1.3.6.1.4.1.1751.2.4.3.6.20
Serial interface data bits. The default value is 8
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 4..8  

psSerialParity 1.3.6.1.4.1.1751.2.4.3.6.21
Serial interface Parity check. The default value is None
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

psSerialStopBits 1.3.6.1.4.1.1751.2.4.3.6.22
Serial interface stop bits. The default value is 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

psSerialFlowControl 1.3.6.1.4.1.1751.2.4.3.6.23
Serial interface Flow control. The default value is None
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psTFTPFileType 1.3.6.1.4.1.1751.2.4.3.6.24
The type of the file to be uploaded or downloaded to/from the access server. The AllConfigFiles options shall upload or download all the configuration files supported.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psDeviceSerialNumber 1.3.6.1.4.1.1751.2.4.3.6.25
This parameter identifies the serial number of the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

psBroadcastMessage 1.3.6.1.4.1.1751.2.4.3.6.26
This parameter allows to set customized messages to be sent to all connected clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

psPOSTVersionNumber 1.3.6.1.4.1.1751.2.4.3.6.27
This parameter identifies the POST version number of the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

psHardwareVersionNumber 1.3.6.1.4.1.1751.2.4.3.6.28
This parameter identifies the Hardware version number of the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

radiusClientMIB 1.3.6.1.4.1.1751.2.4.3.7.2
OBJECT IDENTIFIER    

radiusClientMIBObjects 1.3.6.1.4.1.1751.2.4.3.7.2.1
OBJECT IDENTIFIER    

radiusClient 1.3.6.1.4.1.1751.2.4.3.7.2.1.1
OBJECT IDENTIFIER    

radiusClientInvalidServerAddresses 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.1
The total number of RADIUS Access-Response messages received from unknown addresses since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusServerTable 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2
The (conceptual) table listing the RADIUS servers with which the client shares a secret.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusServerEntry

radiusServerEntry 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1
An entry (conceptual row) representing a RADIUS server with which the client shares a secret.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RadiusServerEntry  

radiusServerIndex 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.1
The RADIUS server with whom the client interacts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

radiusServerType 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.2
The RADIUS server type (Authentication or Accounting or Both). For creating a server entry Server Type should be set
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

radiusServerAddress 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.3
The IP address of the RADIUS server referred to in this table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

radiusServerDestPortAuth 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.4
The Authentication port of the RADIUS Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusServerDestPortAcct 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.5
The Accounting port of the RADIUS Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusClientAccessRequests 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.6
The total number of RADIUS Access-Request messages sent since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccessRetransmissions 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.7
The total number of RADIUS Access-Request messages retransmitted since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccessAccepts 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.8
The total number of RADIUS Access-Accept messages received since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccessChallenges 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.9
The total number of RADIUS Access-Challenge messages received since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientMalformedAccessResponses 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.10
The total number of malformed RADIUS Access-Response messages received since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAuthenticationBadAuthenticators 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.11
The total number of RADIUS Access-Response messages containing invalid authenticators received since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccessRejects 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.12
The total number of RADIUS Access-Reject messages sent since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientTimeouts 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.13
The total number of timeouts since client startup
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccountingRequests 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.14
The total number of RADIUS Accounting-Request messages sent since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccountingRetransmissions 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.15
The total number of RADIUS Accounting-Request messages retransmitted since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccountingResponses 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.16
The total number of RADIUS Accounting-Response messages received since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusClientAccountingBadAuthenticators 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.17
The total number of RADIUS Accounting-Response messages which contained invalid authenticators received since client start-up
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

radiusServerSharedSecret 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.18
The secret string which is shared between Server and Client
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

radiusServerEnabled 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.19
Flag to tell whether the server is active or Inactive
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusServerResponseTime 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.20
The maximum time within which the server has to respond for a request from the client
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

radiusServerMaximumRetransmission 1.3.6.1.4.1.1751.2.4.3.7.2.1.1.2.1.21
The allowed maximum no. of trials to be tried by a client to get response from the server for a request
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

radiusClientMIBConformance 1.3.6.1.4.1.1751.2.4.3.7.2.2
OBJECT IDENTIFIER    

radiusClientMIBCompliances 1.3.6.1.4.1.1751.2.4.3.7.2.2.1
OBJECT IDENTIFIER    

radiusClientMIBGroups 1.3.6.1.4.1.1751.2.4.3.7.2.2.2
OBJECT IDENTIFIER    

psShimECPRetransmissionCount 1.3.6.1.4.1.1751.2.4.3.8.1
The number of retransmissions when responses are not received with the timeout period.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psShimECPRepeatResponseCount 1.3.6.1.4.1.1751.2.4.3.8.2
The number of time the transmitted response can be retransmitted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psShimECPRetransmissionTimeout 1.3.6.1.4.1.1751.2.4.3.8.3
The timeout interval for a response to be received.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psIappStatus 1.3.6.1.4.1.1751.2.4.3.11.1
IAPP Status (whether IAPP feature should be enabled or diaabled)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psIappAnnReqOut 1.3.6.1.4.1.1751.2.4.3.11.2
Number of ANNOUNCE.requests sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappAnnReqIn 1.3.6.1.4.1.1751.2.4.3.11.3
Number of ANNOUNCE.requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappAnnRespOut 1.3.6.1.4.1.1751.2.4.3.11.4
Number of ANNOUNCE.responses sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappAnnRespIn 1.3.6.1.4.1.1751.2.4.3.11.5
Number of ANNOUNCE.responses received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappHandOvrReqOut 1.3.6.1.4.1.1751.2.4.3.11.6
Number of HANDOVER.request sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappHandOvrReqIn 1.3.6.1.4.1.1751.2.4.3.11.7
Number of HANDOVER.request received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappHandOvrRespOut 1.3.6.1.4.1.1751.2.4.3.11.8
Number of HANDOVER.responses sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappHandOvrRespIn 1.3.6.1.4.1.1751.2.4.3.11.9
Number of HANDOVER.responses received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappEndSessOut 1.3.6.1.4.1.1751.2.4.3.11.10
Number of IAPP End-PPP session PDUs sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappEndSessIn 1.3.6.1.4.1.1751.2.4.3.11.11
Number of IAPP End-PPP session PDUs received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappEndSessAckOut 1.3.6.1.4.1.1751.2.4.3.11.12
Number of IAPP End-PPP session acknowledgement PDUs sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappEndSessAckIn 1.3.6.1.4.1.1751.2.4.3.11.13
Number of IAPP End-PPP session acknowledgement PDUs received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappPduDrops 1.3.6.1.4.1.1751.2.4.3.11.14
Number of IAPP PDUs dropped.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappHandOvrReqReSent 1.3.6.1.4.1.1751.2.4.3.11.15
Number of HANDOVER requests re-transmitted..
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIappAnnInterval 1.3.6.1.4.1.1751.2.4.3.11.16
This parameter represents interval in seconds for performing an IAPP announce operation by the device. The units for this parameter is seconds and default value should be 120 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psIappAnnRespTime 1.3.6.1.4.1.1751.2.4.3.11.17
This parameter indicates the amount of time in seconds the device waits to send an IAPP announce response after an announce request message is sent. This parameter is set to a default value of 2 seconds and is not configurable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

psIappHandOvrTimeOut 1.3.6.1.4.1.1751.2.4.3.11.18
This parameter represents the time in milliseconds the device waits before it resends a handover response message. The default value for this parameter should be 512 milliseconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psIappMaxHandOvrRetries 1.3.6.1.4.1.1751.2.4.3.11.19
This parameter indicates the maximum amount of retransmission sent by the device for a handover request message. The default for this parameter should be 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

psIappRoamingClients 1.3.6.1.4.1.1751.2.4.3.11.20
Number of roaming clients currently attached to the Access Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIpxStatus 1.3.6.1.4.1.1751.2.4.3.12.1
Which protocol is supported, i.e, IP or IPX or both IP and IPX.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psIpxDefaultRouterNodeNum 1.3.6.1.4.1.1751.2.4.3.12.2
If the source IPX network number is not equal to the destination IPX Network number in the packet from wireless side to the wired side, then replace the destination Ether MAC addr with the value of this object (Default IPX router node number).
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

psIpxWiredToWlessBridged 1.3.6.1.4.1.1751.2.4.3.12.3
Number of packets bridged from wired side to wireless side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIpxWlessToWiredBridged 1.3.6.1.4.1.1751.2.4.3.12.4
Number of packets bridged from wiredless side to wired side.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psIpxEthernetEncapsulationFormat 1.3.6.1.4.1.1751.2.4.3.12.5
Encapsulation type to be used for the IPX packets sent in wired side
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

psASClientTable 1.3.6.1.4.1.1751.2.4.3.12.6
The (conceptual) table listing the ASClients (IPX) connected to the access server 2000 device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PsASClientEntry

psASClientEntry 1.3.6.1.4.1.1751.2.4.3.12.6.1
An entry (conceptual row) representing a ASClient (IPX) connnected to the Access Server 2000 device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PsASClientEntry  

psPPPSessionId 1.3.6.1.4.1.1751.2.4.3.12.6.1.1
The PPP Session ID assigned by the AS-2000 to this ASClient.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

psIpxClientNetworkNumber 1.3.6.1.4.1.1751.2.4.3.12.6.1.2
The IPX Node Number assigned by the Novell Server to this IPX client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

psIpxClientMAC 1.3.6.1.4.1.1751.2.4.3.12.6.1.3
The Wireless MAC of this IPX Client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

psIpxClientStatus 1.3.6.1.4.1.1751.2.4.3.12.6.1.4
Flag to indicate whether the IPX Client is Active or Inactive. IPX Client status can also be disabled/enabled/deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), disable(2), delete(3)  

psASClientSessionUpTime 1.3.6.1.4.1.1751.2.4.3.12.6.1.5
This object represents the session up time for each AS Client or PPP virttual interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

psASClientPacketsIn 1.3.6.1.4.1.1751.2.4.3.12.6.1.6
This object represents the number of packets (unicast and non-unicast)recieved for each AS Client or PPP virttual interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

psASClientPacketsOut 1.3.6.1.4.1.1751.2.4.3.12.6.1.7
This object represents the number of packets (unicast and non-unicast)sent for each AS Client or PPP virttual interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

oriLinkTestTimeOut 1.3.6.1.4.1.1751.2.4.3.13.1
The value of this parameter determines the time that a link test will continue without any SNMP requests for a Link Test Table entry. When the time expires the Link Test Table is cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

oriLinkTestInterval 1.3.6.1.4.1.1751.2.4.3.13.3
This parameter indicates the interval (in millisec) between sending link test frames to a station. Default on 200 millisecond.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

oriLinkTestExplore 1.3.6.1.4.1.1751.2.4.3.13.4
When this parameter is set to 2, the access point will send out an explore request on all 802.11 interfaces and from the results build the Link Test table. This table is valid only while this parameter is 3.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

oriLinkTestTable 1.3.6.1.4.1.1751.2.4.3.13.5
This table contains the information for the stations currently associated with this access point.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OriLinkTestTableEntry

oriLinkTestTableEntry 1.3.6.1.4.1.1751.2.4.3.13.5.1
This parameter represents the entry in the Remote Link Test table.This is described below.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OriLinkTestTableEntry  

oriLinkTestTableIndex 1.3.6.1.4.1.1751.2.4.3.13.5.1.1
This parameter represents a unique value for each stattion. The value for each station must remain constant at least from one explore to the next.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestInProgress 1.3.6.1.4.1.1751.2.4.3.13.5.1.2
When this parameter is set to 2 the access point will initiate a link test sequence with this station.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

oriLinkTestStationName 1.3.6.1.4.1.1751.2.4.3.13.5.1.3
This parameter identifies the name of the station whom which the link test is being performed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

oriLinkTestMACAddress 1.3.6.1.4.1.1751.2.4.3.13.5.1.4
This variable represents the MAC address that will be mapped to the IP Address of the station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

oriLinkTestStationProfile 1.3.6.1.4.1.1751.2.4.3.13.5.1.5
This parameter represents the profile/capabilities for this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurCurSignalLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.6
The current signal level (in dB)for the link test from this station. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurCurNoiseLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.7
The current noise level (in dB)for the link test to this station. This variable indicates the running average of the local noise level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurCurSNR 1.3.6.1.4.1.1751.2.4.3.13.5.1.8
The current signal to noise ratio for the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMinSignalLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.9
The minimum signal level during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMinNoiseLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.10
The minimum noise level during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMinSNR 1.3.6.1.4.1.1751.2.4.3.13.5.1.11
The minimum signal to noise ratio during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMaxSignalLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.12
The maximum signal level during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMaxNoiseLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.13
The maximum noise level during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMaxSNR 1.3.6.1.4.1.1751.2.4.3.13.5.1.14
The maximum signal to noise ratio during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurLowFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.15
The total number of frames sent at 1 Mbit/s speed during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurStandardFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.16
The total number of frames sent at 2 Mbit/s speed during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurMediumFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.17
The total number of frames sent at 5.5 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestOurHighFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.18
The total number of frames sent at 11 Mbit/s (for Turbo-8, it is 8 Mbit/s) speed during the link test to this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisCurSignalLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.19
The current signal level for the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisCurNoiseLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.20
The current noise level for the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisCurSNR 1.3.6.1.4.1.1751.2.4.3.13.5.1.21
The current signal to noise ratio for the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMinSignalLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.22
The minimum signal level during the link test to the remote statio or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMinNoiseLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.23
The minimum noise level during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMinSNR 1.3.6.1.4.1.1751.2.4.3.13.5.1.24
The minimum signal to noise ratio during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMaxSignalLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.25
The maximum signal level during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMaxNoiseLevel 1.3.6.1.4.1.1751.2.4.3.13.5.1.26
The maximum noise level during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMaxSNR 1.3.6.1.4.1.1751.2.4.3.13.5.1.27
The maximum signal to noise ratio during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisLowFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.28
The total number of frames sent at 1 Mbit/s speed during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisStandardFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.29
The total number of frames sent at 2 Mbit/s speed during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisMediumFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.30
The total number of frames sent at 5.5 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestHisHighFrameCount 1.3.6.1.4.1.1751.2.4.3.13.5.1.31
The total number of frames sent at 11 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to the remote station or access point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestInterface 1.3.6.1.4.1.1751.2.4.3.13.5.1.32
The PCMCIA Card Number to which the Client has sent the Explore Response Message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

oriLinkTestRadioType 1.3.6.1.4.1.1751.2.4.3.13.5.1.33
The Wireless Standard eg. IEEE 802.11 or IEEE 802.11b used on the Radio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accessServerTrapVariables 1.3.6.1.4.1.1751.2.4.3.15.1
OBJECT IDENTIFIER    

accessServerGenericInformationMessage 1.3.6.1.4.1.1751.2.4.3.15.1.1
Any generic string information can be sent as this message.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

accessServerMacAddress 1.3.6.1.4.1.1751.2.4.3.15.1.2
The MAC address that is sent with the traps to identify which Access Server has the problem
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

accessServerFailedTFTPServerAddress 1.3.6.1.4.1.1751.2.4.3.15.1.3
The ip address configured as the TFTP server for which the operation upload/download failed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpAddress  

accessServerFailedTFTPFilename 1.3.6.1.4.1.1751.2.4.3.15.1.4
The filename configured to be retrieved/sent from/to the TFTP server for which the operation upload/download failed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

accessServerFailedTFTPOperation 1.3.6.1.4.1.1751.2.4.3.15.1.5
This variable used in conjunction with the different TFTP traps ( TFTPInitiated, TFTPFailed, TFTPCompleted)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

accessServerSuspendedTaskName 1.3.6.1.4.1.1751.2.4.3.15.1.6
The task that was suspended, can be several tasks executed within the Access Server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

accessServerWirelessCard 1.3.6.1.4.1.1751.2.4.3.15.1.7
This trap variable is used to determine on which Wireless Card, PC Card A or PC Card B, a wireless TRAP has occured on.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER pc-cardA(1), pc-cardB(2)  

accessServerFlashRelatedTraps 1.3.6.1.4.1.1751.2.4.3.15.2
OBJECT IDENTIFIER    

accessServerFlashEmpty 1
This trap is sent when the FLASH is empty.
TRAP-TYPE    

accessServerFlashCorrupted 2
This trap is sent when the data in the FLASH is corrupted.
TRAP-TYPE    

accessServerConfigurationRelatedTraps 1.3.6.1.4.1.1751.2.4.3.15.3
OBJECT IDENTIFIER    

accessServerInvalidKey 1
This trap is sent when an invalid key is detected at the accessServer.
TRAP-TYPE    

accessServerAPMNotConfigured 2
This trap is sent when the APM information is not configured in the Access Server.
TRAP-TYPE    

accessServerWLCIncompatibleFirmware 3
This trap is sent when an ORiNOCO PC Card plugged in the Access Server is not compatible with the firmware versions supported.
TRAP-TYPE    

accessServerWLCFailure 4
This trap is sent when an ORiNOCO PC Card is not present or there is a failure in the ORiNOCO PC card.
TRAP-TYPE    

accessServerWLCRemoval 5
This trap is generated when the ORiNOCO PC Card is removed from the Access Server.
TRAP-TYPE    

accessServerRadiusNotConfigured 6
This trap is sent when the radius information is not configured in the Access Server.
TRAP-TYPE    

accessServerDNSIPNotConfigured 7
This trap is sent when the DNS IP information is not configured in the Access Server.
TRAP-TYPE    

accessServerNBNSIPNotConfigured 8
This trap is sent when the NBNS IP information is not configured in the Access Server.
TRAP-TYPE    

accessServerRadiusAuthenticationNotConfigured 9
This trap is sent when the radius authentication information is not configured in the Access Server.
TRAP-TYPE    

accessServerRadiusAccountingNotConfigured 10
This trap is sent when the radius accounting information is not configured in the Access Server.
TRAP-TYPE    

accessServerDuplicateIPAddressEncountered 11
This trap is sent when the IP Address of the Access Server is also used by someother device in the network.
TRAP-TYPE    

accessServerWLCVoltageDiscrepancy 12
This trap is sent when non 5volt card or 3.3 v card is inserted in the Access Server.
TRAP-TYPE    

accessServerWLCIncompatibleVendor 13
This trap is generated when an incompatible wireless vendor card is inserted or present in the Access Server.
TRAP-TYPE    

accessServerWLCFirmwareDownloadFailure 14
This trap is generated when a failure occurs during the firmware download process.
TRAP-TYPE    

accessServerDiagnosticTraps 1.3.6.1.4.1.1751.2.4.3.15.4
OBJECT IDENTIFIER    

accessServerTFTPInitiated 1
This trap is sent when a TFTP operation happens at the Access Server.
TRAP-TYPE    

accessServerTFTPCompleted 2
This trap is sent when a TFTP operation failure happens at the Access Server.
TRAP-TYPE    

accessServerTFTPFailure 3
This trap is sent when a TFTP operation failure happens at the Access Server.
TRAP-TYPE    

accessServerAdminStateMadeUp 4
This trap is sent when the Access Server Admin state is made 'up'
TRAP-TYPE    

accessServerAdminStateMadeDown 5
This trap is sent when the Access Server Admin state is made 'down'
TRAP-TYPE    

accessServerRebootingNow 6
This trap is sent when the Access Server is about to reboot.
TRAP-TYPE    

accessServerTaskSuspended 7
This trap is sent when a task has suspended in the Access Server.
TRAP-TYPE    

accessServerBootPFailed 8
This trap is sent when the BootP protocol in the bootloader has failed.
TRAP-TYPE    

accessServerDHCPFailed 9
This trap is sent when the DHCP in the application software has failed.
TRAP-TYPE    

accessServerImageTraps 1.3.6.1.4.1.1751.2.4.3.15.5
OBJECT IDENTIFIER    

accessServerZeroSizeImage 1
This trap is sent when an image of size zero (0) is downloaded to the access server.
TRAP-TYPE    

accessServerNonVxWorksImage 2
This trap is sent when a non-VxWorks image is downloaded to the access server.
TRAP-TYPE    

accessServerImageTooLarge 3
This trap is sent when the image downloaded to the access server exceeds the size limitation of 5 MB.
TRAP-TYPE