ANNEX-MIB

File: ANNEX-MIB.mib (52343 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212

Imported symbols

enterprises NetworkAddress IpAddress
Counter Gauge TimeTicks
DisplayString PhysAddress OBJECT-TYPE

Defined Types

PortEntry  
SEQUENCE    
  anxpPortIndex INTEGER
  anxpMode INTEGER
  anxpCtrlLines INTEGER
  anxpBidirModem INTEGER
  anxpAllowBcast INTEGER
  anxpBcastDirection INTEGER
  anxpInputStartChar DisplayString
  anxpInputStopChar DisplayString
  anxpOutputStartChar DisplayString
  anxpOutputStopChar DisplayString
  anxpIxanyFlowCtl INTEGER
  anxpLongBreak INTEGER
  anxpShortBreak INTEGER
  anxpForwardTimer INTEGER
  anxpForwardCount INTEGER
  anxpImask7Bits INTEGER
  anxpAttnChar DisplayString
  anxpInputBufSize INTEGER
  anxpInputIsActivity INTEGER
  anxpOutputIsActivity INTEGER
  anxpInactivityTimer INTEGER
  anxpResetIdleTimer INTEGER
  anxpCliInactivity INTEGER
  anxpCliSecurity INTEGER
  anxpConnectSecurity INTEGER
  anxpPortServerSecurity INTEGER
  anxpPortPassword DisplayString
  anxpUserName DisplayString
  anxpDedicatedAddr IpAddress
  anxpDedicatedPort DisplayString
  anxpPrompt DisplayString
  anxpTermVar DisplayString
  anxpNewLineTerm INTEGER
  anxpEcho INTEGER
  anxpMapToLower INTEGER
  anxpMapToUpper INTEGER
  anxpHardwareTabs INTEGER
  anxpCharErase INTEGER
  anxpLineErase INTEGER
  anxpEraseChar DisplayString
  anxpEraseWord DisplayString
  anxpEraseLine DisplayString
  anxpRedisplayLine DisplayString
  anxpToggleOutput DisplayString
  anxpTelnetEscape DisplayString
  anxpNeedDsr INTEGER
  anxpTelnetCRLF INTEGER
  anxpLatbEnable INTEGER
  anxpSlipSecure INTEGER
  anxpNetLocalAddr IpAddress
  anxpNetRemoteAddr IpAddress
  anxpSlipSubnetMask IpAddress
  anxpSlipLoadDumpHost IpAddress
  anxpNetMetric INTEGER
  anxpSlipAllowDump INTEGER
  anxpSlipDoCompression INTEGER
  anxpSlipAllowCompression INTEGER
  anxpSlipMtuSize INTEGER
  anxpSlipNoIcmp INTEGER
  anxpSlipTos INTEGER
  anxpPppMru INTEGER
  anxpPppAcm INTEGER
  anxpPppSecurityProto INTEGER
  anxpPppUserRemote DisplayString
  anxpPppPasswdRemote DisplayString
  anxpLatAuthGroupVal DisplayString
  anxpPppDialupAddr INTEGER
  anxpBanner INTEGER
  anxpPsHistory INTEGER
  anxpLocation DisplayString
  anxpType INTEGER
  anxpCliImask7 INTEGER

AnxpParaPortEntry  
SEQUENCE    
  anxpParaPortIndex INTEGER
  anxpParaPortHardwareTabs INTEGER
  anxpParaPortMapToUpper INTEGER
  anxpParaPortPrinterWidth INTEGER
  anxpParaPortInterface INTEGER
  anxpParaPortSpeed INTEGER

Defined Values

xylogics 1.3.6.1.4.1.15
OBJECT IDENTIFIER    

prod 1.3.6.1.4.1.15.1
OBJECT IDENTIFIER    

prodannex 1.3.6.1.4.1.15.1.1
Product name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

annex 1.3.6.1.4.1.15.2
OBJECT IDENTIFIER    

hw 1.3.6.1.4.1.15.2.1
OBJECT IDENTIFIER    

sw 1.3.6.1.4.1.15.2.2
OBJECT IDENTIFIER    

ports 1.3.6.1.4.1.15.2.3
OBJECT IDENTIFIER    

parallelport 1.3.6.1.4.1.15.2.4
OBJECT IDENTIFIER    

annexconfig 1.3.6.1.4.1.15.2.5
OBJECT IDENTIFIER    

annexcmds 1.3.6.1.4.1.15.2.6
OBJECT IDENTIFIER    

hwType 1.3.6.1.4.1.15.2.1.1
An identifier for the Annex hardware type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER err(1), annexII(16), annex3(42), microannex(52), microels(55)  

hwRev 1.3.6.1.4.1.15.2.1.2
The revision level of the hardware platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

romRev 1.3.6.1.4.1.15.2.1.3
The revision number of the ROM Monitor software.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

serialNumber 1.3.6.1.4.1.15.2.1.4
The serial number assigned to the unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySize 1.3.6.1.4.1.15.2.1.5
The amount of memory present in the unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swType 1.3.6.1.4.1.15.2.2.1
The software version currently running on the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER err(1), annexIImx(16), annexIIux(17), annex3ux(42), annex3mx(43), microannexux(52), microannexmx(53), microels(55)  

swRevMajor 1.3.6.1.4.1.15.2.2.2
The major software release number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swRevMinor 1.3.6.1.4.1.15.2.2.3
The minor software release number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swBuild 1.3.6.1.4.1.15.2.2.4
The full name of the software build, including the software version, major and minor version numbers and the date and time of the build.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

imageName 1.3.6.1.4.1.15.2.2.5
The name of the most recently booted image.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

bootHost 1.3.6.1.4.1.15.2.2.6
The Internet address of the host from which the Annex booted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

defaultDomain 1.3.6.1.4.1.15.2.2.7
The default domain name provided by the DNS nameserver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

currentDate 1.3.6.1.4.1.15.2.2.8
The current date and time provided by the time server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

usableMemory 1.3.6.1.4.1.15.2.2.9
The amount of available for data buffers and other structures after the Annex has booted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

freeMemory 1.3.6.1.4.1.15.2.2.10
The amount of currently available memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

minFreeMemory 1.3.6.1.4.1.15.2.2.11
The minimum amount of free memory since booting the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuUtilization 1.3.6.1.4.1.15.2.2.12
Percent of CPU time currently being used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

maxProcs 1.3.6.1.4.1.15.2.2.13
The total number of process structures allocated for use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mostProcs 1.3.6.1.4.1.15.2.2.14
The maximum number of active processes since the Annex was booted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

activeProcs 1.3.6.1.4.1.15.2.2.15
The number of currently active processes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cpuIRescheds 1.3.6.1.4.1.15.2.2.16
The number of processes whose time slice has expired in the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cpuTRescheds 1.3.6.1.4.1.15.2.2.17
The total number of processes whose time slice has expired since booting the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

contextISwtchs 1.3.6.1.4.1.15.2.2.18
The number of context switches in the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

contextTSwtchs 1.3.6.1.4.1.15.2.2.19
The total number of context switches since booting the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cpuIActivates 1.3.6.1.4.1.15.2.2.20
The number of processes that were activated in the last minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

cpuTActivates 1.3.6.1.4.1.15.2.2.21
The number of processes that were activated since booting the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

maxCallouts 1.3.6.1.4.1.15.2.2.22
The number of allocated Callout structures for timed events in the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

leastCallouts 1.3.6.1.4.1.15.2.2.23
The minimum number of Callout structures available since last booting the Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

freeCallouts 1.3.6.1.4.1.15.2.2.24
The current number of free Callout structures.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

totalPorts 1.3.6.1.4.1.15.2.3.1
The number of serial ports on this Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

totalInChars 1.3.6.1.4.1.15.2.3.2
The total number of characters received on all serial ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

totalOutChars 1.3.6.1.4.1.15.2.3.3
The total number of characters transmitted on all serial ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

totalParityErrs 1.3.6.1.4.1.15.2.3.4
The total number of parity errors detected on all serial ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

totalOverrunErrs 1.3.6.1.4.1.15.2.3.5
The total number of overruns detected on all serial ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

totalFramingErrs 1.3.6.1.4.1.15.2.3.6
The total number of framing errors detected on all serial ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portTable 1.3.6.1.4.1.15.2.3.7
Table of port entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.15.2.3.7.1
The port's configuration parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortEntry  

anxpPortIndex 1.3.6.1.4.1.15.2.3.7.1.1
A unique number from 1 to totalPorts that identifies each serial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

anxpMode 1.3.6.1.4.1.15.2.3.7.1.2
This parameter defines the mode for access to the serial line port. The default is cli
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cli(1), slave(2), adaptive(3), unused(4), slip(5), dedicated(6), ppp(7)  

anxpCtrlLines 1.3.6.1.4.1.15.2.3.7.1.3
The type of hardware control used on the port: modem control (dcddtr), flow control (ctsrts), or both.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), dcddtr(2), ctsrts(3), both(4)  

anxpBidirModem 1.3.6.1.4.1.15.2.3.7.1.4
This parameter controls whether the port is configured for adaptive use with a bidirectional modem.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpAllowBcast 1.3.6.1.4.1.15.2.3.7.1.5
Controls whether the serial port can receive administrative broadcast messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpBcastDirection 1.3.6.1.4.1.15.2.3.7.1.6
Defines the direction that an administrative broadcast message is sent. This parameter is valid only when the port is defined as a slave port by the anxpMode parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER port(1), network(2)  

anxpInputStartChar 1.3.6.1.4.1.15.2.3.7.1.7
The control character sequence that restarts input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpInputStopChar 1.3.6.1.4.1.15.2.3.7.1.8
The control character sequence that stops input if the charPortInFlowType parameter (in the char MIB) is set to xonXoff.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpOutputStartChar 1.3.6.1.4.1.15.2.3.7.1.9
The control character sequence that restarts output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpOutputStopChar 1.3.6.1.4.1.15.2.3.7.1.10
The control character sequence that stops output if the charPortOutFlowType parameter (in the char MIB) is set to xonXoff.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpIxanyFlowCtl 1.3.6.1.4.1.15.2.3.7.1.11
This parameter specifies whether any input character will be treated as a start (xon) character when output has been suspended by a stop (xoff) character.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpLongBreak 1.3.6.1.4.1.15.2.3.7.1.12
This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break greater than two seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpShortBreak 1.3.6.1.4.1.15.2.3.7.1.13
This parameter controls whether the Annex returns the user to the CLI prompt after receiving a break shorter than two seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpForwardTimer 1.3.6.1.4.1.15.2.3.7.1.14
This parameter defines the inter-character timer that sets the amount of time, in tens of milliseconds, that will elapse before forwarding the received data. The value of zero turns off the timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

anxpForwardCount 1.3.6.1.4.1.15.2.3.7.1.15
Specifies the number of received characters buffered for the port by the Annex before forwarding the characters to the host or network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

anxpImask7Bits 1.3.6.1.4.1.15.2.3.7.1.16
When enabled, instructs the Annex to ignore the eighth bit of all received characters on the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpAttnChar 1.3.6.1.4.1.15.2.3.7.1.17
Defines a control character sequence as an attention character to return the user to the CLI prompt. The Annex-II only allows a single control character (eg. ^A), while the Annex3 and MicroAnnex allow a string of control characters to be defined (eg. ^A^B^Z).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2..32)  

anxpInputBufSize 1.3.6.1.4.1.15.2.3.7.1.18
The number of 256-byte blocks allocated to receive input characters from this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 4..255  

anxpInputIsActivity 1.3.6.1.4.1.15.2.3.7.1.19
Controls whether received input characters are considered as activity for the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpOutputIsActivity 1.3.6.1.4.1.15.2.3.7.1.20
Controls whether transmitted output characters are considered as activity for the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpInactivityTimer 1.3.6.1.4.1.15.2.3.7.1.21
The amount of time, in minutes, which a port can remain inactive before the Annex terminates all sessions and resets the port. A value of 0 disables the timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

anxpResetIdleTimer 1.3.6.1.4.1.15.2.3.7.1.22
Defines whether input or output resets the idle timer for the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER input(1), output(2)  

anxpCliInactivity 1.3.6.1.4.1.15.2.3.7.1.23
The amount of time, in minutes, that the Annex waits before hanging up the serial port after it becomes idle. A value of 0 turns off the timer. A value of 255 means immediate, which causes the Annex to hang up the port immediately after exiting from the last job.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

anxpCliSecurity 1.3.6.1.4.1.15.2.3.7.1.24
This parameter controls whether security is enabled for the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpConnectSecurity 1.3.6.1.4.1.15.2.3.7.1.25
This parameter controls whether the host-based security policy is enabled for access from the port to the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpPortServerSecurity 1.3.6.1.4.1.15.2.3.7.1.26
This parameter controls whether the host-based security policy is enabled for access to the port from the port server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpPortPassword 1.3.6.1.4.1.15.2.3.7.1.27
This parameter defines a password for the port for local password protection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

anxpUserName 1.3.6.1.4.1.15.2.3.7.1.28
A string defining the user name for the user of the serial port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

anxpDedicatedAddr 1.3.6.1.4.1.15.2.3.7.1.29
When the anxpMode parameter is set to dedicated, this parameter defines the Internet address of the host to which this port can connect to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxpDedicatedPort 1.3.6.1.4.1.15.2.3.7.1.30
The application name or TCP port number to which this port can connect when the anxpMode parameter is set to dedicated. The allowed application names are 'telnet', 'rlogin', 'login', 'call', and 'mls'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

anxpPrompt 1.3.6.1.4.1.15.2.3.7.1.31
This parameter defines a port-specific prompt.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

anxpTermVar 1.3.6.1.4.1.15.2.3.7.1.32
A string defining the type of terminal attached to the serial port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

anxpNewLineTerm 1.3.6.1.4.1.15.2.3.7.1.33
This parameter controls whether a carriage return is echoed as just a carriage return (enabled), or whether the carriage return is echoed as a carriage return and line feed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpEcho 1.3.6.1.4.1.15.2.3.7.1.34
This parameter controls whether the Annex echoes all characters as they are received from the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpMapToLower 1.3.6.1.4.1.15.2.3.7.1.35
When enabled, the Annex translates all upper case characters to lower case as they are received from the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpMapToUpper 1.3.6.1.4.1.15.2.3.7.1.36
When enabled, the Annex translates all lower case characters to upper case as they are transmitted to the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpHardwareTabs 1.3.6.1.4.1.15.2.3.7.1.37
When enabled, this parameter allows the Annex to expand ASCII tab characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpCharErase 1.3.6.1.4.1.15.2.3.7.1.38
This parameter controls whether the Annex echoes the character erase and word erase characters for a video terminal (enabled) or for a hard-copy terminal (disabled).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpLineErase 1.3.6.1.4.1.15.2.3.7.1.39
This parameter controls whether the Annex echoes the line erase character for a video terminal (enabled) or for a hard-copy terminal (disabled).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpEraseChar 1.3.6.1.4.1.15.2.3.7.1.40
Defines the character erase control character sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpEraseWord 1.3.6.1.4.1.15.2.3.7.1.41
Defines the word erase control character sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpEraseLine 1.3.6.1.4.1.15.2.3.7.1.42
Defines the line erase control character sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpRedisplayLine 1.3.6.1.4.1.15.2.3.7.1.43
Defines the reprint line control character sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpToggleOutput 1.3.6.1.4.1.15.2.3.7.1.44
Defines the flush control character used to flush the output buffer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpTelnetEscape 1.3.6.1.4.1.15.2.3.7.1.45
Defines the control character that returns the user to the telnet: prompt when running the CLI telnet command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

anxpNeedDsr 1.3.6.1.4.1.15.2.3.7.1.46
Specifies whether the DSR signal needs to be asserted when connecting to a slave port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpTelnetCRLF 1.3.6.1.4.1.15.2.3.7.1.47
Defines what characters are transmitted out the port to the network when the End-of-Line character is sensed. 'enabled' means transmit Line-Feed and Carriage-Return. 'disabled' means transmit Carriage-Return and NULL. The default is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpLatbEnable 1.3.6.1.4.1.15.2.3.7.1.48
Controls interpretation of LAT Data-B packets received from host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpSlipSecure 1.3.6.1.4.1.15.2.3.7.1.49
If anxEnableSecurity is not set, this parameter selects slip session logging. If anxEnableSecurity is set, this parameter permits slip access only from secure ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpNetLocalAddr 1.3.6.1.4.1.15.2.3.7.1.50
The Internet address for the Annex's side of the point-to-point (SLIP or PPP) link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxpNetRemoteAddr 1.3.6.1.4.1.15.2.3.7.1.51
The Internet address for the host at the remote end of the point-to-point (SLIP or PPP) link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxpSlipSubnetMask 1.3.6.1.4.1.15.2.3.7.1.52
The subnet mask for this SLIP interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxpSlipLoadDumpHost 1.3.6.1.4.1.15.2.3.7.1.53
The Internet address of the host from which the Annex receives a load or to which the Annex sends a dump over the SLIP interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxpNetMetric 1.3.6.1.4.1.15.2.3.7.1.54
This parameter defines the hop count to the remote end of the SLIP or PPP interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..64  

anxpSlipAllowDump 1.3.6.1.4.1.15.2.3.7.1.55
This parameter defines whether the Annex is allowed to dump across a SLIP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpSlipDoCompression 1.3.6.1.4.1.15.2.3.7.1.56
When enabled, the Annex will start TCP/IP header compression on this SLIP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpSlipAllowCompression 1.3.6.1.4.1.15.2.3.7.1.57
When enabled, the Annex will use TCP/IP header compression on this SLIP link only if the other end of the SLIP link initiates the compression.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpSlipMtuSize 1.3.6.1.4.1.15.2.3.7.1.58
Force the compressed SLIP interface to use a Maximum Transmission Unit (MTU) of either 1024 bytes (large) or 256 bytes (small). The default is large.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER large(1), small(2)  

anxpSlipNoIcmp 1.3.6.1.4.1.15.2.3.7.1.59
When enabled, the Annex will discard any ICMP packets directed to this SLIP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpSlipTos 1.3.6.1.4.1.15.2.3.7.1.60
When enabled, the Annex sends interactive traffic over this SLIP link before any other traffic.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpPppMru 1.3.6.1.4.1.15.2.3.7.1.61
This parameter defines the maximum receive unit in bytes. The default value is 1500.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 64..1500  

anxpPppAcm 1.3.6.1.4.1.15.2.3.7.1.62
This parameter specifies which of the first 32 bytes (0x00, ... 0x1F) can be sent as clear text and which need to be escaped. A bit on in the mask indicates the character must be escaped. The mask should be specified as an 8 hex character string (0x1F000000 and 1F000000 are both acceptable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(8..10)  

anxpPppSecurityProto 1.3.6.1.4.1.15.2.3.7.1.63
Defines which security protocol will be used to authenticate the remote user. This parameter must be set and the Annex enable_security (anxEnableSecurity) must be enabled before authentication is performed. The default is none
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), pap(2)  

anxpPppUserRemote 1.3.6.1.4.1.15.2.3.7.1.64
The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will return either if the username is defined or if the username is not defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

anxpPppPasswdRemote 1.3.6.1.4.1.15.2.3.7.1.65
The username used by the Annex to identify itself if the remote PPP peer asks for authentication. Reading this parameter will return either if the password is defined or if the password is not defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

anxpLatAuthGroupVal 1.3.6.1.4.1.15.2.3.7.1.66
This port parameter specifies which remote group codes are accessible to a user on a particular Annex port. Each port has its own set of group codes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(32)  

anxpPppDialupAddr 1.3.6.1.4.1.15.2.3.7.1.67
When enabled, the Annex requests the PPP dialup addresses from the host-based ACP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpBanner 1.3.6.1.4.1.15.2.3.7.1.68
Specifies whether the Annex banner and message- of-the-day are displayed on the port. The default is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpPsHistory 1.3.6.1.4.1.15.2.3.7.1.69
Specifies how much data to buffer on a slave port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32767  

anxpLocation 1.3.6.1.4.1.15.2.3.7.1.70
A descriptive string for a this port. This string is displayed by the CLI who command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

anxpType 1.3.6.1.4.1.15.2.3.7.1.71
The type of device attached to the port. The default is hardwired.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dialin(1), hardwired(2), terminal(3), modem(4), printer(5)  

anxpCliImask7 1.3.6.1.4.1.15.2.3.7.1.72
Defines whether input at the CLI is masked to 7 bitx. The default is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpParaPorts 1.3.6.1.4.1.15.2.4.1
The number of parallel ports on this Annex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

anxpParaPortTable 1.3.6.1.4.1.15.2.4.2
Table of parallel port parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AnxpParaPortEntry

anxpParaPortEntry 1.3.6.1.4.1.15.2.4.2.1
The Annex parallel port configuration parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AnxpParaPortEntry  

anxpParaPortIndex 1.3.6.1.4.1.15.2.4.2.1.1
A unique number from 1 to anxpParaPorts that identifies each parallel port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

anxpParaPortHardwareTabs 1.3.6.1.4.1.15.2.4.2.1.2
This parameter controls whether the Annex will send a tab character to the printer. If disabled, the tab is replaced with spaces.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpParaPortMapToUpper 1.3.6.1.4.1.15.2.4.2.1.3
When enabled, the Annex translates all lower case characters to upper case before transmitting the characters to the printer port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxpParaPortPrinterWidth 1.3.6.1.4.1.15.2.4.2.1.4
The defined maximum number of characters per printer line.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 40..132  

anxpParaPortInterface 1.3.6.1.4.1.15.2.4.2.1.5
The type of printer attached to the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER centronics(1), dataproducts(2)  

anxpParaPortSpeed 1.3.6.1.4.1.15.2.4.2.1.6
The printer speed on the Micro-Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), high-speed(2)  

anxInetAddr 1.3.6.1.4.1.15.2.5.1
The Internet address of the Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxPrefLoadAddr 1.3.6.1.4.1.15.2.5.2
The preferred load address for the Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxPrefDumpAddr 1.3.6.1.4.1.15.2.5.3
The preferred dump address for the Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxLoadDumpGateway 1.3.6.1.4.1.15.2.5.4
The Internet address of a gateway used when the preferred load or dump host is on a different network or subnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxLoadDumpSeq 1.3.6.1.4.1.15.2.5.5
Lists the available network interfaces and the order that the Annex uses them when doing a down-line load or up-line dump.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

anxLoadBcast 1.3.6.1.4.1.15.2.5.6
This parameter defines whether the Annex broadcasts for the config or the motd files if they were not found on the preferred load host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxServerCap 1.3.6.1.4.1.15.2.5.7
Defines whether the Annex can act as a file server host for another Annex. The allowable values are 'all', 'none' (the default), or one or more of the following names separated by commas: 'config', 'motd', 'image'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

anxTimeBcast 1.3.6.1.4.1.15.2.5.8
This parameter defines whether the Annex broadcasts for the time if the preferred load host does not provide a time server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxBcastAddr 1.3.6.1.4.1.15.2.5.9
The Internet address used by the Annex when sending broadcasts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxSubnetMask 1.3.6.1.4.1.15.2.5.10
The Internet subnet mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxAuthAgent 1.3.6.1.4.1.15.2.5.11
This parameter controls whether the Annex can send an ICMP Address Mask Reply to a received ICMP Address Mask Request.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxMaxVcli 1.3.6.1.4.1.15.2.5.12
The maximum number of virtual CLI connections allowed by the Annex at any one time. 0 means the Annex does not allow VCLI connections. 255 allows the Annex to maintain an unlimited number of VCLI connections.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

anxIpEncapType 1.3.6.1.4.1.15.2.5.13
This parameter specifies whether the Annex encapsulates IP packets in the Ethernet format or the IEEE 802.2/802.3 Data Link Layer format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ethernet(1), ieee802(2)  

anxNameServer1Type 1.3.6.1.4.1.15.2.5.14
The name service type used by the primary nameserver host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), ien116(2), dns(3)  

anxNameServer1Addr 1.3.6.1.4.1.15.2.5.15
The Internet address of the primary nameserver host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxNameServer2Type 1.3.6.1.4.1.15.2.5.16
The name service type used by the secondary nameserver host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), ien116(2), dns(3)  

anxNameServer2Addr 1.3.6.1.4.1.15.2.5.17
The Internet address of the secondary nameserver host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxNameServerBcast 1.3.6.1.4.1.15.2.5.18
This parameter controls whether the Annex broadcasts a name server request if the preferred name servers do not respond.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxRwhod 1.3.6.1.4.1.15.2.5.19
Defines whether the Annex listens for RWHO broadcasts when building its host table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxMinUniqueHostNames 1.3.6.1.4.1.15.2.5.20
Defines whether the Annex minimum uniqueness feature is available.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxHostTableSize 1.3.6.1.4.1.15.2.5.21
Defines the number of entries in the Annex host table. 0 indicates no host table. 251 sets no limit on the size of the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..251  

anxRouted 1.3.6.1.4.1.15.2.5.22
Defines whether the RIP-listener of the routing daemon on the Annex is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxEnableSecurity 1.3.6.1.4.1.15.2.5.23
This parameter controls whether the Annex security system is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxPassword 1.3.6.1.4.1.15.2.5.24
Setting this parameter changes the Annex's administration password. Reading this parameter will return either if the password is defined or if the password is not defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

anxSecurServer1Addr 1.3.6.1.4.1.15.2.5.25
The Internet address of the primary host where the Annex sends its security requests.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxSecurServer2Addr 1.3.6.1.4.1.15.2.5.26
The Internet address of the secondary host where the Annex sends its security requests.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxNetTurnAround 1.3.6.1.4.1.15.2.5.27
The amount of time (in seconds) that the Annex waits for a response from a security server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

anxSecurBcast 1.3.6.1.4.1.15.2.5.28
This parameter controls whether the Annex will broadcast its security requests when neither of the preferred security servers are available.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxVcliSecurity 1.3.6.1.4.1.15.2.5.29
This parameter controls whether the Annex performs user validation on the virtual CLI connections.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

anxVcliPassword 1.3.6.1.4.1.15.2.5.30
This parameter defines a password used by the Annex when setting up a virtual CLI connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

anxAcpKey 1.3.6.1.4.1.15.2.5.31
This parameter defines the Annex's encryption key used when exchanging messages between the Annex and the security server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

anxSysLogMask 1.3.6.1.4.1.15.2.5.32
Defines the priority levels of events logged in the Annex syslog file. The allowable values are 'all', 'none', or one or more of the following level names separated by commas: 'emergency', 'alert', 'critical', 'error', 'warning', 'notice', 'info', 'debug'
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

anxSysLogFacility 1.3.6.1.4.1.15.2.5.33
This parameter defines the 4.3BSD syslog facility used in logging the Annex messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER loglocal0(17), loglocal1(18), loglocal2(19), loglocal3(20), loglocal4(21), loglocal5(22), loglocal6(23), loglocal7(24)  

anxSysLogHost 1.3.6.1.4.1.15.2.5.34
The Internet address of the host configured to log Annex messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

anxCliPrompt 1.3.6.1.4.1.15.2.5.35
The string used by the Annex to prompt all CLI users.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

anxMotdFile 1.3.6.1.4.1.15.2.5.36
The host file name that contains the message-of-the-day for the Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

anxTftpDirName 1.3.6.1.4.1.15.2.5.37
Specifies the directory name to be prepended to all files (boot image, motd, macros, etc.) when booting via TFTP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

anxTftpDumpName 1.3.6.1.4.1.15.2.5.38
The full pathname of the TFTP dump file, if any.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

anxTimeZone 1.3.6.1.4.1.15.2.5.39
Defines the timezone where the Annex resides in minutes west of GMT.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -1200..1200  

anxDaylightSavings 1.3.6.1.4.1.15.2.5.40
Defines the daylight savings time for the geographic location of the Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER us(1), australian(2), westeuropean(3), mideuropean(4), easteuropean(5), canadian(6), british(7), none(8)  

anxLatKey 1.3.6.1.4.1.15.2.5.41
The Annex specific LAT key used to enable or disable the LAT protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

anxCircuitTimer 1.3.6.1.4.1.15.2.5.42
The time interval in tens of milliseconds between the transmission of LAT packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

anxFacilityNum 1.3.6.1.4.1.15.2.5.43
The LAT facility number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32767  

anxLatGroupVal 1.3.6.1.4.1.15.2.5.44
The Annex LAT group code for permitting access to LAT services. To access a specific LAT service, the Annex must have at least one enabled group code match the service's set group codes. The Annex will not maintain any information about unauthorized services. The value is displayed as a string of hex characters with each bit defining whether a specific group is enabled or disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(32)  

anxKeepAliveTimer 1.3.6.1.4.1.15.2.5.45
The time interval, in seconds, between the transmission of identification packets during times of network inactivity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..255  

anxReXmitLimit 1.3.6.1.4.1.15.2.5.46
The number of times to retransmit a packet before notifying the user of a network failure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 4..120  

anxServerName 1.3.6.1.4.1.15.2.5.47
A string of up to 16 characters used to name the Annex in the LAT protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

anxServiceLimit 1.3.6.1.4.1.15.2.5.48
This parameter defines the upper bound on the number of services that the Annex can maintain in its local service table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 16..2048  

anxConfigFile 1.3.6.1.4.1.15.2.5.49
The name of the host file that contains the alias and menu entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

anxLatVcliGroupVal 1.3.6.1.4.1.15.2.5.50
This Annex parameter specifies which remote group codes are accessible to virtual cli users. All virtual cli users have the same group code. The value is displayed as a string of hex characters with each bit defining whether a specific group is enabled or disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(32)  

anxLatQueueMax 1.3.6.1.4.1.15.2.5.51
Defines the maximum number of host requests (HIC's) that the Annex will save in its internal queue when the requested resource is not available (port busy).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

anxLatLocation 1.3.6.1.4.1.15.2.5.52
A string of up to 32 characters used to identify the location of the Annex for the LAT protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

anxDisabledModules 1.3.6.1.4.1.15.2.5.53
Defines which selectable modules are currently disabled. The allowable values are 'all', 'none' or one or more of the following names separated by commas: 'admin', 'lat', 'ppp', 'slip', 'snmp', 'nameserver', 'cli-edit'. If this is a MicroAnnex ELS, the values 'ppp' and 'slip' are not valid.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

anxSysLogPort 1.3.6.1.4.1.15.2.5.54
Specifies the Annex port number where syslog messages are sent. If set to 0, syslog messages are not sent to an Annex port. This is independent of any host-based syslogging that may be enabled. The maximum port number allowed will depend on the highest numbered port on the specific Annex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..64  

anxcBoot 1.3.6.1.4.1.15.2.6.1
The type of boot to be performed. To initiate a dump, this parameter needs to be set by the management station. The values stored in anxcBootImage, anxcBootTime, and anxcBootMsg are used as needed, depending on the boot type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER immediate(1), delayed(2), dumpboot(3), diagnosticboot(4), abortschedule(5), quiet(6)  

anxcBootImage 1.3.6.1.4.1.15.2.6.2
The name of the image file to be used with the boot command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

anxcBootTime 1.3.6.1.4.1.15.2.6.3
The time at which the next boot is scheduled in HH:MM format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(5..10)  

anxcBootMsg 1.3.6.1.4.1.15.2.6.4
The broadcast message to be displayed when the next boot is performed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

anxcReset 1.3.6.1.4.1.15.2.6.5
Writing a value to this object causes the annex to reset the appropriate subsystem.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all(1), macros(2), motd(3), nameserver(4), security(5), printerport(6), serialports(7), virtualports(8)  

anxcBcast 1.3.6.1.4.1.15.2.6.6
Writing a value to this object causes the annex to send the message in anxcBcastMsg to the specified port set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all(1), serial(2), virtual(3)  

anxcBcastMsg 1.3.6.1.4.1.15.2.6.7
The message to be broadcast to the Annex ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)