ALCOMA-MIB

File: ALCOMA-MIB.mib (58975 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC-1212
RFC1213-MIB

Imported symbols

enterprises Unsigned32 OBJECT-TYPE
DisplayString

Defined Values

alcoma 1.3.6.1.4.1.12140
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.12140.1
OBJECT IDENTIFIER    

alMP 1.3.6.1.4.1.12140.2
OBJECT IDENTIFIER    


alNMS 1.3.6.1.4.1.12140.1.2
OBJECT IDENTIFIER    

alStatusLED 1.3.6.1.4.1.12140.1.1.1
OBJECT IDENTIFIER    

alEHW 1.3.6.1.4.1.12140.1.1.1.1
Hardware error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alESR 1.3.6.1.4.1.12140.1.1.1.2
Signal error in radio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alESL 1.3.6.1.4.1.12140.1.1.1.3
Signal error on lines.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alCA 1.3.6.1.4.1.12140.1.1.1.4
Non-standard command activate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

local-station 1.3.6.1.4.1.12140.1.1.2
OBJECT IDENTIFIER    

alL-General 1.3.6.1.4.1.12140.1.1.2.1
OBJECT IDENTIFIER    

alLSupervisor 1.3.6.1.4.1.12140.1.1.2.1.1
Active supervisor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), none(0), terminal(1), local(2), network(3), service(4), alcoma(5)  

alLConfiguration 1.3.6.1.4.1.12140.1.1.2.1.2
IDU configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), undefined(0), cf2xE1(1), cf4xE1(2), cf1xE2(3), cf1xE1-Ethernet(4), cf1xE3-E1(7), cf1xEthernet(8), cf1xEthF-E1(9), cf1xEthF-E1-1xE1(10), cf1xEthF-E1-2xE1(11), cf1xEthF-E1-3xE1(12), cf1xEthF-E1-4xE1(13), cf1xEthF-E1-5xE1(14), cf1xEthF-E1-6xE1(15), cf1xEthF-E1-7xE1(16), cf1xEthF-E1-8xE1(17), cf1xEthF(18), cf1xEthF-1xE1(19), cf1xEthF-2xE1(20), cf1xEthF-3xE1(21), cf1xEthF-4xE1(22), cf1xEthF-5xE1(23), cf1xEthF-6xE1(24), cf1xEthF-7xE1(25), cf1xEthF-8xE1(26), cf2xFEth(27), cf2xFEth-1xE1(28), cf4xFEth-2xE1(29), cf2xGEth(30), cf2xGEth-SFP100(31), cf2xGEth-SFP1000(32), cf2xGEth-SFPSG(33)  

alLStatus 1.3.6.1.4.1.12140.1.1.2.1.3
Station alarm status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(0), ok(1), warning(2), error(3)  

alLHistory 1.3.6.1.4.1.12140.1.1.2.1.4
History alarm status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alLIAISL 1.3.6.1.4.1.12140.1.1.2.1.5
Automatic AIS ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLILEVPWR 1.3.6.1.4.1.12140.1.1.2.1.6
Low RX or TX level alarms ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-ODU 1.3.6.1.4.1.12140.1.1.2.2
OBJECT IDENTIFIER    

alLRX-Level 1.3.6.1.4.1.12140.1.1.2.2.1
Signal receiver level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alLTX-PWR 1.3.6.1.4.1.12140.1.1.2.2.2
Transmitter power level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alLMode-TX 1.3.6.1.4.1.12140.1.1.2.2.3
Mode of power control.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), manual(1), atpc(2)  

alLODU-LB 1.3.6.1.4.1.12140.1.1.2.2.4
ODU line-loopback.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Modem 1.3.6.1.4.1.12140.1.1.2.3
OBJECT IDENTIFIER    

alLQuality 1.3.6.1.4.1.12140.1.1.2.3.1
Quality of 4-level modulation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), out(1)  

alL-Supply 1.3.6.1.4.1.12140.1.1.2.4
OBJECT IDENTIFIER    

alLVoltage-5V 1.3.6.1.4.1.12140.1.1.2.4.1
Voltage 5V high.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), high(1)  

alLVoltage-5Vor15V 1.3.6.1.4.1.12140.1.1.2.4.2
Voltage 5V or 15V low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alLVoltage-24V 1.3.6.1.4.1.12140.1.1.2.4.3
Voltage 24V low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alLCurrent-ODU 1.3.6.1.4.1.12140.1.1.2.4.4
ODU current range.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), out(1)  

alLInput 1.3.6.1.4.1.12140.1.1.2.4.5
Input voltage low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alL-IDU 1.3.6.1.4.1.12140.1.1.2.5
OBJECT IDENTIFIER    

alLEEPROM 1.3.6.1.4.1.12140.1.1.2.5.1
EEPROM memory status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alLRAM 1.3.6.1.4.1.12140.1.1.2.5.2
RAM memory status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alLBattery 1.3.6.1.4.1.12140.1.1.2.5.3
RAM backup battery voltage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alLCommIDU 1.3.6.1.4.1.12140.1.1.2.5.4
Communication status with blocks of IDU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alLCommRMT 1.3.6.1.4.1.12140.1.1.2.5.5
Communication status with remote station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alL-MUX 1.3.6.1.4.1.12140.1.1.2.6
OBJECT IDENTIFIER    

alLBER-10E6 1.3.6.1.4.1.12140.1.1.2.6.1
BER > 10E-6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alLBER-10E4 1.3.6.1.4.1.12140.1.1.2.6.2
BER > 10E-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alLFrame 1.3.6.1.4.1.12140.1.1.2.6.3
Frame LOSS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), loss(1)  

alL-PDH1 1.3.6.1.4.1.12140.1.1.2.7
OBJECT IDENTIFIER    

alLPDHFrame 1.3.6.1.4.1.12140.1.1.2.7.1
PDH1 frame LOSS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), loss(1)  

alLAISPDH 1.3.6.1.4.1.12140.1.1.2.7.2
AIS to PDH1 frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), on(1)  

alLLLBPDH 1.3.6.1.4.1.12140.1.1.2.7.3
Line loopback on PDH1 frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLBPDH 1.3.6.1.4.1.12140.1.1.2.7.4
Radio loopback on PDH1 frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line1 1.3.6.1.4.1.12140.1.1.2.9
OBJECT IDENTIFIER    

alLOSS1 1.3.6.1.4.1.12140.1.1.2.9.1
LOSS on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alILOSS1 1.3.6.1.4.1.12140.1.1.2.9.2
Ignore LOSS on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alAIS1 1.3.6.1.4.1.12140.1.1.2.9.3
AIS to line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alAISL1 1.3.6.1.4.1.12140.1.1.2.9.4
AIS from line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLB1 1.3.6.1.4.1.12140.1.1.2.9.5
Line loopback on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLB1 1.3.6.1.4.1.12140.1.1.2.9.6
Radio loopback on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line2 1.3.6.1.4.1.12140.1.1.2.10
OBJECT IDENTIFIER    

alLLOSS2 1.3.6.1.4.1.12140.1.1.2.10.1
LOSS on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS2 1.3.6.1.4.1.12140.1.1.2.10.2
Ignore LOSS on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS2 1.3.6.1.4.1.12140.1.1.2.10.3
AIS to line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL2 1.3.6.1.4.1.12140.1.1.2.10.4
AIS from line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB2 1.3.6.1.4.1.12140.1.1.2.10.5
Line loopback on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB2 1.3.6.1.4.1.12140.1.1.2.10.6
Radio loopback on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line3 1.3.6.1.4.1.12140.1.1.2.11
OBJECT IDENTIFIER    

alLLOSS3 1.3.6.1.4.1.12140.1.1.2.11.1
LOSS on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS3 1.3.6.1.4.1.12140.1.1.2.11.2
Ignore LOSS on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS3 1.3.6.1.4.1.12140.1.1.2.11.3
AIS to line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL3 1.3.6.1.4.1.12140.1.1.2.11.4
AIS from line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB3 1.3.6.1.4.1.12140.1.1.2.11.5
Line loopback on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB3 1.3.6.1.4.1.12140.1.1.2.11.6
Radio loopback on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line4 1.3.6.1.4.1.12140.1.1.2.12
OBJECT IDENTIFIER    

alLLOSS4 1.3.6.1.4.1.12140.1.1.2.12.1
LOSS on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS4 1.3.6.1.4.1.12140.1.1.2.12.2
Ignore LOSS on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS4 1.3.6.1.4.1.12140.1.1.2.12.3
AIS to line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL4 1.3.6.1.4.1.12140.1.1.2.12.4
AIS from line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB4 1.3.6.1.4.1.12140.1.1.2.12.5
Line loopback on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB4 1.3.6.1.4.1.12140.1.1.2.12.6
Radio loopback on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line5 1.3.6.1.4.1.12140.1.1.2.13
OBJECT IDENTIFIER    

alLLOSS5 1.3.6.1.4.1.12140.1.1.2.13.1
LOSS on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS5 1.3.6.1.4.1.12140.1.1.2.13.2
Ignore LOSS on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS5 1.3.6.1.4.1.12140.1.1.2.13.3
AIS to line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL5 1.3.6.1.4.1.12140.1.1.2.13.4
AIS from line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB5 1.3.6.1.4.1.12140.1.1.2.13.5
Line loopback on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB5 1.3.6.1.4.1.12140.1.1.2.13.6
Radio loopback on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line6 1.3.6.1.4.1.12140.1.1.2.14
OBJECT IDENTIFIER    

alLLOSS6 1.3.6.1.4.1.12140.1.1.2.14.1
LOSS on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS6 1.3.6.1.4.1.12140.1.1.2.14.2
Ignore LOSS on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS6 1.3.6.1.4.1.12140.1.1.2.14.3
AIS to line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL6 1.3.6.1.4.1.12140.1.1.2.14.4
AIS from line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB6 1.3.6.1.4.1.12140.1.1.2.14.5
Line loopback on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB6 1.3.6.1.4.1.12140.1.1.2.14.6
Radio loopback on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line7 1.3.6.1.4.1.12140.1.1.2.15
OBJECT IDENTIFIER    

alLLOSS7 1.3.6.1.4.1.12140.1.1.2.15.1
LOSS on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS7 1.3.6.1.4.1.12140.1.1.2.15.2
Ignore LOSS on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS7 1.3.6.1.4.1.12140.1.1.2.15.3
AIS to line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL7 1.3.6.1.4.1.12140.1.1.2.15.4
AIS from line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB7 1.3.6.1.4.1.12140.1.1.2.15.5
Line loopback on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB7 1.3.6.1.4.1.12140.1.1.2.15.6
Radio loopback on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line8 1.3.6.1.4.1.12140.1.1.2.16
OBJECT IDENTIFIER    

alLLOSS8 1.3.6.1.4.1.12140.1.1.2.16.1
LOSS on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS8 1.3.6.1.4.1.12140.1.1.2.16.2
Ignore LOSS on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS8 1.3.6.1.4.1.12140.1.1.2.16.3
AIS to line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL8 1.3.6.1.4.1.12140.1.1.2.16.4
AIS from line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB8 1.3.6.1.4.1.12140.1.1.2.16.5
Line loopback on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB8 1.3.6.1.4.1.12140.1.1.2.16.6
Radio loopback on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line9 1.3.6.1.4.1.12140.1.1.2.17
OBJECT IDENTIFIER    

alLLOSS9 1.3.6.1.4.1.12140.1.1.2.17.1
LOSS on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS9 1.3.6.1.4.1.12140.1.1.2.17.2
Ignore LOSS on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS9 1.3.6.1.4.1.12140.1.1.2.17.3
AIS to line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL9 1.3.6.1.4.1.12140.1.1.2.17.4
AIS from line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB9 1.3.6.1.4.1.12140.1.1.2.17.5
Line loopback on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB9 1.3.6.1.4.1.12140.1.1.2.17.6
Radio loopback on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line10 1.3.6.1.4.1.12140.1.1.2.18
OBJECT IDENTIFIER    

alLLOSS10 1.3.6.1.4.1.12140.1.1.2.18.1
LOSS on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS10 1.3.6.1.4.1.12140.1.1.2.18.2
Ignore LOSS on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS10 1.3.6.1.4.1.12140.1.1.2.18.3
AIS to line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL10 1.3.6.1.4.1.12140.1.1.2.18.4
AIS from line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB10 1.3.6.1.4.1.12140.1.1.2.18.5
Line loopback on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB10 1.3.6.1.4.1.12140.1.1.2.18.6
Radio loopback on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line11 1.3.6.1.4.1.12140.1.1.2.19
OBJECT IDENTIFIER    

alLLOSS11 1.3.6.1.4.1.12140.1.1.2.19.1
LOSS on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS11 1.3.6.1.4.1.12140.1.1.2.19.2
Ignore LOSS on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS11 1.3.6.1.4.1.12140.1.1.2.19.3
AIS to line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL11 1.3.6.1.4.1.12140.1.1.2.19.4
AIS from line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB11 1.3.6.1.4.1.12140.1.1.2.19.5
Line loopback on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB11 1.3.6.1.4.1.12140.1.1.2.19.6
Radio loopback on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alL-Line12 1.3.6.1.4.1.12140.1.1.2.20
OBJECT IDENTIFIER    

alLLOSS12 1.3.6.1.4.1.12140.1.1.2.20.1
LOSS on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLILOSS12 1.3.6.1.4.1.12140.1.1.2.20.2
Ignore LOSS on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLAIS12 1.3.6.1.4.1.12140.1.1.2.20.3
AIS to line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alLAISL12 1.3.6.1.4.1.12140.1.1.2.20.4
AIS from line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLLLB12 1.3.6.1.4.1.12140.1.1.2.20.5
Line loopback on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alLRLB12 1.3.6.1.4.1.12140.1.1.2.20.6
Radio loopback on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

remote-station 1.3.6.1.4.1.12140.1.1.3
OBJECT IDENTIFIER    

alR-General 1.3.6.1.4.1.12140.1.1.3.1
OBJECT IDENTIFIER    

alRSupervisor 1.3.6.1.4.1.12140.1.1.3.1.1
Active supervisor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), none(0), terminal(1), local(2), network(3), service(4), alcoma(5)  

alRConfiguration 1.3.6.1.4.1.12140.1.1.3.1.2
IDU configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), undefined(0), cf2xE1(1), cf4xE1(2), cf1xE2(3), cf1xE1-Ethernet(4), cf1xE3-E1(7), cf1xEthernet(8), cf1xEthF-E1(9), cf1xEthF-E1-1xE1(10), cf1xEthF-E1-2xE1(11), cf1xEthF-E1-3xE1(12), cf1xEthF-E1-4xE1(13), cf1xEthF-E1-5xE1(14), cf1xEthF-E1-6xE1(15), cf1xEthF-E1-7xE1(16), cf1xEthF-E1-8xE1(17), cf1xEthF(18), cf1xEthF-1xE1(19), cf1xEthF-2xE1(20), cf1xEthF-3xE1(21), cf1xEthF-4xE1(22), cf1xEthF-5xE1(23), cf1xEthF-6xE1(24), cf1xEthF-7xE1(25), cf1xEthF-8xE1(26), cf2xFEth(27), cf2xFEth-1xE1(28), cf4xFEth-2xE1(29), cf2xGEth(30), cf2xGEth-SFP100(31), cf2xGEth-SFP1000(32), cf2xGEth-SFPSG(33)  

alRStatus 1.3.6.1.4.1.12140.1.1.3.1.3
Station alarm status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(0), ok(1), warning(2), error(3)  

alRHistory 1.3.6.1.4.1.12140.1.1.3.1.4
History alarm status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alRIAISL 1.3.6.1.4.1.12140.1.1.3.1.5
Automatic AIS ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRILEVPWR 1.3.6.1.4.1.12140.1.1.3.1.6
Low RX or TX level alarms ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-ODU 1.3.6.1.4.1.12140.1.1.3.2
OBJECT IDENTIFIER    

alRRX-Level 1.3.6.1.4.1.12140.1.1.3.2.1
Signal receiver level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alRTX-PWR 1.3.6.1.4.1.12140.1.1.3.2.2
Transmitter power level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alRMode-TX 1.3.6.1.4.1.12140.1.1.3.2.3
Mode of power control.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), manual(1), atpc(2)  

alRODU-LB 1.3.6.1.4.1.12140.1.1.3.2.4
ODU line-loopback.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Modem 1.3.6.1.4.1.12140.1.1.3.3
OBJECT IDENTIFIER    

alRQuality 1.3.6.1.4.1.12140.1.1.3.3.1
Quality of 4-level modulation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), out(1)  

alR-Supply 1.3.6.1.4.1.12140.1.1.3.4
OBJECT IDENTIFIER    

alRVoltage-5V 1.3.6.1.4.1.12140.1.1.3.4.1
Voltage 5V high.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), high(1)  

alRVoltage-5Vor15V 1.3.6.1.4.1.12140.1.1.3.4.2
Voltage 5V or 15V low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alRVoltage-24V 1.3.6.1.4.1.12140.1.1.3.4.3
Voltage 24V low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alRCurrent-ODU 1.3.6.1.4.1.12140.1.1.3.4.4
ODU current range.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), out(1)  

alRInput 1.3.6.1.4.1.12140.1.1.3.4.5
Input voltage low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alR-IDU 1.3.6.1.4.1.12140.1.1.3.5
OBJECT IDENTIFIER    

alREEPROM 1.3.6.1.4.1.12140.1.1.3.5.1
EEPROM memory status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alRRAM 1.3.6.1.4.1.12140.1.1.3.5.2
RAM memory status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alRBattery 1.3.6.1.4.1.12140.1.1.3.5.3
RAM backup battery voltage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alRCommIDU 1.3.6.1.4.1.12140.1.1.3.5.4
Communication status with blocks of IDU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alRCommRMT 1.3.6.1.4.1.12140.1.1.3.5.5
Communication status with remote station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alR-MUX 1.3.6.1.4.1.12140.1.1.3.6
OBJECT IDENTIFIER    

alRBER-10E6 1.3.6.1.4.1.12140.1.1.3.6.1
BER > 10E-6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alRBER-10E4 1.3.6.1.4.1.12140.1.1.3.6.2
BER > 10E-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alRFrame 1.3.6.1.4.1.12140.1.1.3.6.3
Frame LOSS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), loss(1)  

alR-PDH1 1.3.6.1.4.1.12140.1.1.3.7
OBJECT IDENTIFIER    

alRPDHFrame 1.3.6.1.4.1.12140.1.1.3.7.1
PDH1 frame LOSS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), loss(1)  

alRAISPDH 1.3.6.1.4.1.12140.1.1.3.7.2
AIS to frame PDH1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), on(1)  

alRLLBPDH 1.3.6.1.4.1.12140.1.1.3.7.3
Line loopback on PDH1 frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLBPDH 1.3.6.1.4.1.12140.1.1.3.7.4
Radio loopback on PDH1 frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line1 1.3.6.1.4.1.12140.1.1.3.9
OBJECT IDENTIFIER    

alRLOSS1 1.3.6.1.4.1.12140.1.1.3.9.1
LOSS on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS1 1.3.6.1.4.1.12140.1.1.3.9.2
Ignore LOSS on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS1 1.3.6.1.4.1.12140.1.1.3.9.3
AIS to line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL1 1.3.6.1.4.1.12140.1.1.3.9.4
AIS from line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB1 1.3.6.1.4.1.12140.1.1.3.9.5
Line loopback on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB1 1.3.6.1.4.1.12140.1.1.3.9.6
Radio loopback on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line2 1.3.6.1.4.1.12140.1.1.3.10
OBJECT IDENTIFIER    

alRLOSS2 1.3.6.1.4.1.12140.1.1.3.10.1
LOSS on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS2 1.3.6.1.4.1.12140.1.1.3.10.2
Ignore LOSS on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS2 1.3.6.1.4.1.12140.1.1.3.10.3
AIS to line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL2 1.3.6.1.4.1.12140.1.1.3.10.4
AIS from line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB2 1.3.6.1.4.1.12140.1.1.3.10.5
Line loopback on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB2 1.3.6.1.4.1.12140.1.1.3.10.6
Radio loopback on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line3 1.3.6.1.4.1.12140.1.1.3.11
OBJECT IDENTIFIER    

alRLOSS3 1.3.6.1.4.1.12140.1.1.3.11.1
LOSS on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS3 1.3.6.1.4.1.12140.1.1.3.11.2
Ignore LOSS on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS3 1.3.6.1.4.1.12140.1.1.3.11.3
AIS to line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL3 1.3.6.1.4.1.12140.1.1.3.11.4
AIS from line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB3 1.3.6.1.4.1.12140.1.1.3.11.5
Line loopback on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB3 1.3.6.1.4.1.12140.1.1.3.11.6
Radio loopback on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line4 1.3.6.1.4.1.12140.1.1.3.12
OBJECT IDENTIFIER    

alRLOSS4 1.3.6.1.4.1.12140.1.1.3.12.1
LOSS on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS4 1.3.6.1.4.1.12140.1.1.3.12.2
Ignore LOSS on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS4 1.3.6.1.4.1.12140.1.1.3.12.3
AIS to line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL4 1.3.6.1.4.1.12140.1.1.3.12.4
AIS from line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB4 1.3.6.1.4.1.12140.1.1.3.12.5
Line loopback on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB4 1.3.6.1.4.1.12140.1.1.3.12.6
Radio loopback on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line5 1.3.6.1.4.1.12140.1.1.3.13
OBJECT IDENTIFIER    

alRLOSS5 1.3.6.1.4.1.12140.1.1.3.13.1
LOSS on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS5 1.3.6.1.4.1.12140.1.1.3.13.2
Ignore LOSS on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS5 1.3.6.1.4.1.12140.1.1.3.13.3
AIS to line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL5 1.3.6.1.4.1.12140.1.1.3.13.4
AIS from line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB5 1.3.6.1.4.1.12140.1.1.3.13.5
Line loopback on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB5 1.3.6.1.4.1.12140.1.1.3.13.6
Radio loopback on line 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line6 1.3.6.1.4.1.12140.1.1.3.14
OBJECT IDENTIFIER    

alRLOSS6 1.3.6.1.4.1.12140.1.1.3.14.1
LOSS on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS6 1.3.6.1.4.1.12140.1.1.3.14.2
Ignore LOSS on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS6 1.3.6.1.4.1.12140.1.1.3.14.3
AIS to line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL6 1.3.6.1.4.1.12140.1.1.3.14.4
AIS from line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB6 1.3.6.1.4.1.12140.1.1.3.14.5
Line loopback on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB6 1.3.6.1.4.1.12140.1.1.3.14.6
Radio loopback on line 6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line7 1.3.6.1.4.1.12140.1.1.3.15
OBJECT IDENTIFIER    

alRLOSS7 1.3.6.1.4.1.12140.1.1.3.15.1
LOSS on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS7 1.3.6.1.4.1.12140.1.1.3.15.2
Ignore LOSS on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS7 1.3.6.1.4.1.12140.1.1.3.15.3
AIS to line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL7 1.3.6.1.4.1.12140.1.1.3.15.4
AIS from line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB7 1.3.6.1.4.1.12140.1.1.3.15.5
Line loopback on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB7 1.3.6.1.4.1.12140.1.1.3.15.6
Radio loopback on line 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line8 1.3.6.1.4.1.12140.1.1.3.16
OBJECT IDENTIFIER    

alRLOSS8 1.3.6.1.4.1.12140.1.1.3.16.1
LOSS on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS8 1.3.6.1.4.1.12140.1.1.3.16.2
Ignore LOSS on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS8 1.3.6.1.4.1.12140.1.1.3.16.3
AIS to line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL8 1.3.6.1.4.1.12140.1.1.3.16.4
AIS from line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB8 1.3.6.1.4.1.12140.1.1.3.16.5
Line loopback on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB8 1.3.6.1.4.1.12140.1.1.3.16.6
Radio loopback on line 8.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line9 1.3.6.1.4.1.12140.1.1.3.17
OBJECT IDENTIFIER    

alRLOSS9 1.3.6.1.4.1.12140.1.1.3.17.1
LOSS on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS9 1.3.6.1.4.1.12140.1.1.3.17.2
Ignore LOSS on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS9 1.3.6.1.4.1.12140.1.1.3.17.3
AIS to line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL9 1.3.6.1.4.1.12140.1.1.3.17.4
AIS from line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB9 1.3.6.1.4.1.12140.1.1.3.17.5
Line loopback on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB9 1.3.6.1.4.1.12140.1.1.3.17.6
Radio loopback on line 9.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line10 1.3.6.1.4.1.12140.1.1.3.18
OBJECT IDENTIFIER    

alRLOSS10 1.3.6.1.4.1.12140.1.1.3.18.1
LOSS on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS10 1.3.6.1.4.1.12140.1.1.3.18.2
Ignore LOSS on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS10 1.3.6.1.4.1.12140.1.1.3.18.3
AIS to line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL10 1.3.6.1.4.1.12140.1.1.3.18.4
AIS from line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB10 1.3.6.1.4.1.12140.1.1.3.18.5
Line loopback on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB10 1.3.6.1.4.1.12140.1.1.3.18.6
Radio loopback on line 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line11 1.3.6.1.4.1.12140.1.1.3.19
OBJECT IDENTIFIER    

alRLOSS11 1.3.6.1.4.1.12140.1.1.3.19.1
LOSS on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS11 1.3.6.1.4.1.12140.1.1.3.19.2
Ignore LOSS on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS11 1.3.6.1.4.1.12140.1.1.3.19.3
AIS to line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL11 1.3.6.1.4.1.12140.1.1.3.19.4
AIS from line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB11 1.3.6.1.4.1.12140.1.1.3.19.5
Line loopback on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB11 1.3.6.1.4.1.12140.1.1.3.19.6
Radio loopback on line 11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alR-Line12 1.3.6.1.4.1.12140.1.1.3.20
OBJECT IDENTIFIER    

alRLOSS12 1.3.6.1.4.1.12140.1.1.3.20.1
LOSS on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRILOSS12 1.3.6.1.4.1.12140.1.1.3.20.2
Ignore LOSS on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRAIS12 1.3.6.1.4.1.12140.1.1.3.20.3
AIS to line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alRAISL12 1.3.6.1.4.1.12140.1.1.3.20.4
AIS from line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRLLB12 1.3.6.1.4.1.12140.1.1.3.20.5
Line loopback on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLB12 1.3.6.1.4.1.12140.1.1.3.20.6
Radio loopback on line 12.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alRRLTrap 1.3.6.1.4.1.12140.1.1.4
OBJECT IDENTIFIER    

alLast-Message 1.3.6.1.4.1.12140.1.1.4.1
Message giving more detailed information on change of alarms status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

traps 1.3.6.1.4.1.12140.0
OBJECT IDENTIFIER    

generalOFF 1.3.6.1.4.1.12140.0.1
OBJECT IDENTIFIER    

generalOK 1.3.6.1.4.1.12140.0.2
OBJECT IDENTIFIER    

generalWAR 1.3.6.1.4.1.12140.0.3
OBJECT IDENTIFIER    

generalERR 1.3.6.1.4.1.12140.0.4
OBJECT IDENTIFIER    

receiverLowAlarmOn 1.3.6.1.4.1.12140.0.5
OBJECT IDENTIFIER    

receiverLowAlarmOff 1.3.6.1.4.1.12140.0.6
OBJECT IDENTIFIER    

transmitterLowAlarmOn 1.3.6.1.4.1.12140.0.7
OBJECT IDENTIFIER    

transmitterLowAlarmOff 1.3.6.1.4.1.12140.0.8
OBJECT IDENTIFIER    

signalQualityAlarmOn 1.3.6.1.4.1.12140.0.9
OBJECT IDENTIFIER    

signalQualityAlarmOff 1.3.6.1.4.1.12140.0.10
OBJECT IDENTIFIER    

ber6EAlarmOn 1.3.6.1.4.1.12140.0.11
OBJECT IDENTIFIER    

ber6EAlarmOff 1.3.6.1.4.1.12140.0.12
OBJECT IDENTIFIER    

ber4EAlarmOn 1.3.6.1.4.1.12140.0.13
OBJECT IDENTIFIER    

ber4EAlarmOff 1.3.6.1.4.1.12140.0.14
OBJECT IDENTIFIER    

inputSupplyAlarmOn 1.3.6.1.4.1.12140.0.15
OBJECT IDENTIFIER    

inputSupplyAlarmOff 1.3.6.1.4.1.12140.0.16
OBJECT IDENTIFIER    

aisFromLineAlarmOn 1.3.6.1.4.1.12140.0.17
OBJECT IDENTIFIER    

aisFromLineAlarmOff 1.3.6.1.4.1.12140.0.18
OBJECT IDENTIFIER    

aisToLineAlarmOn 1.3.6.1.4.1.12140.0.19
OBJECT IDENTIFIER    

aisToLineAlarmOff 1.3.6.1.4.1.12140.0.20
OBJECT IDENTIFIER    

aisToPdhAlarmOn 1.3.6.1.4.1.12140.0.21
OBJECT IDENTIFIER    

aisToPdhAlarmOff 1.3.6.1.4.1.12140.0.22
OBJECT IDENTIFIER    

lossAtLineAlarmOn 1.3.6.1.4.1.12140.0.23
OBJECT IDENTIFIER    

lossAtLineAlarmOff 1.3.6.1.4.1.12140.0.24
OBJECT IDENTIFIER    

lossAtPdhAlarmOn 1.3.6.1.4.1.12140.0.25
OBJECT IDENTIFIER    

lossAtPdhAlarmOff 1.3.6.1.4.1.12140.0.26
OBJECT IDENTIFIER    

lossAtFrameAlarmOn 1.3.6.1.4.1.12140.0.27
OBJECT IDENTIFIER    

lossAtFrameAlarmOff 1.3.6.1.4.1.12140.0.28
OBJECT IDENTIFIER    

trapParam 1.3.6.1.4.1.12140.1.2.1
OBJECT IDENTIFIER    

nmsTrapTime 1.3.6.1.4.1.12140.1.2.1.1
Time of alarms scan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

trapSequence 1.3.6.1.4.1.12140.1.2.1.2
Number of trap sequence.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

mwRouteID 1.3.6.1.4.1.12140.1.2.1.3
Identification of microwave route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

stationID 1.3.6.1.4.1.12140.1.2.1.4
Identification of Radio Relay Link station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

stationName 1.3.6.1.4.1.12140.1.2.1.5
Name of Radio Relay Link station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

mgmtGWaddr 1.3.6.1.4.1.12140.1.2.1.6
IP address of Management Gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

lineID 1.3.6.1.4.1.12140.1.2.1.7
Line ID number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

alMPStatusLED 1.3.6.1.4.1.12140.2.1
OBJECT IDENTIFIER    

alMPEHW 1.3.6.1.4.1.12140.2.1.1
Hardware error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alMPESR 1.3.6.1.4.1.12140.2.1.2
Signal error in radio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alMPESL 1.3.6.1.4.1.12140.2.1.3
Signal error on lines.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alMPCA 1.3.6.1.4.1.12140.2.1.4
Non-standard command activate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alMPGeneral 1.3.6.1.4.1.12140.2.2
OBJECT IDENTIFIER    

alMPSupervisor 1.3.6.1.4.1.12140.2.2.1
Active supervisor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), none(0), terminal(1), local(2), network(3), service(4), alcoma(5)  

alMPConfiguration 1.3.6.1.4.1.12140.2.2.2
IDU configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), undefined(0), cf2xE1(1), cf4xE1(2), cf1xE2(3), cf1xE1-Ethernet(4), cf1xE3-E1(7), cf1xEthernet(8), cf1xEthF-E1(9), cf1xEthF-E1-1xE1(10), cf1xEthF-E1-2xE1(11), cf1xEthF-E1-3xE1(12), cf1xEthF-E1-4xE1(13), cf1xEthF-E1-5xE1(14), cf1xEthF-E1-6xE1(15), cf1xEthF-E1-7xE1(16), cf1xEthF-E1-8xE1(17), cf1xEthF(18), cf1xEthF-1xE1(19), cf1xEthF-2xE1(20), cf1xEthF-3xE1(21), cf1xEthF-4xE1(22), cf1xEthF-5xE1(23), cf1xEthF-6xE1(24), cf1xEthF-7xE1(25), cf1xEthF-8xE1(26), cf2xFEth(27), cf2xFEth-1xE1(28), cf4xFEth-2xE1(29), cf2xGEth(30), cf2xGEth-SFP100(31), cf2xGEth-SFP1000(32), cf2xGEth-SFPSG(33)  

alMPStatus 1.3.6.1.4.1.12140.2.2.3
Station alarm status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(0), ok(1), warning(2), error(3)  

alMPHistory 1.3.6.1.4.1.12140.2.2.4
History alarm status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alMPIAISL 1.3.6.1.4.1.12140.2.2.5
Automatic AIS ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPILEVPWR 1.3.6.1.4.1.12140.2.2.6
Low RX or TX level alarms ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPODU 1.3.6.1.4.1.12140.2.3
OBJECT IDENTIFIER    

alMPTuneTX 1.3.6.1.4.1.12140.2.3.1
Transmitter frequency [MHz].
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

alMPTuneRX 1.3.6.1.4.1.12140.2.3.2
Receiver frequency [MHz].
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

alMPTX-PWR 1.3.6.1.4.1.12140.2.3.3
Transmitter power level [dB].
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-128)  

alMPRX-Level 1.3.6.1.4.1.12140.2.3.4
Signal receiver level [dB].
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-128)  

alMPTX-PWRAlrm 1.3.6.1.4.1.12140.2.3.5
Alarm transmitter power level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), out(1)  

alMPRX-LevelAlrm 1.3.6.1.4.1.12140.2.3.6
Alarm signal receiver level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alMPMode-TX 1.3.6.1.4.1.12140.2.3.7
Mode of power control.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), manual(1), atpc(2)  

alMPODU-LB 1.3.6.1.4.1.12140.2.3.8
ODU line-loopback.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPTemperature 1.3.6.1.4.1.12140.2.3.9
Temperature ODU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1)  

alMPModem 1.3.6.1.4.1.12140.2.4
OBJECT IDENTIFIER    

alMPQuality 1.3.6.1.4.1.12140.2.4.1
Quality of signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1)  

alMPSNR 1.3.6.1.4.1.12140.2.4.2
Signal noise ratio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

alMPQualityAlrm 1.3.6.1.4.1.12140.2.4.3
Alarm quality of signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), out(1)  

alMPSNRAlrm 1.3.6.1.4.1.12140.2.4.4
Alarm signal noise ratio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alMPRate 1.3.6.1.4.1.12140.2.4.5
Transmision rate of link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ndef(0), r300Mbps(1), r200Mbps(2), r16Mbps1(3), r282Mbps(4), r40Mbps1(5), r20Mbps1(6), r10Mbps1(7), r5Mbps1(8), r179Mbps(9), r230Mbps(10), r14Mbps(11), r32Mbps2(12), r44Mbps(13), r22Mbps(14), r11Mbps(15), r5Mbps(16), r66Mbps(17), r33Mbps(18), r16Mbps(19), r8Mbps(20), r80Mbps(21), r333Mbps(22), r355Mbps(23), r384Mbps(24), r50Mbps(25), r72Mbps(26), r100Mbps(27), r123Mbps(28), r158Mbps(29), r168Mbps(30), r77Mbps(31), r35Mbps(32), r25Mbps(33), r165Mbps(34), r61Mbps(35), r39Mbps(36), r19Mbps(37), r17Mbps(38), r30Mbps(39), r34Mbps(40), r60Mbps(41), r178Mbps(42), r186Mbps(43), r1250Mbps(44), r70Mbps(45), r58Mbps(46), r116Mbps(47), r149Mbps(48), r183Mbps(49), r216Mbps(50), r249Mbps(51), r31Mbps(52), r41Mbps(53), r59Mbps(54), r64Mbps(55), r69Mbps(56), r83Mbps(57), r102Mbps(58), r119Mbps(59), r127Mbps(60), r137Mbps(61), r89Mbps(62)  

alMPQAM 1.3.6.1.4.1.12140.2.4.6
Low transnission rate of link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ndef(0), mp4FSK(1), mpQPSK(2), mp4QAM1(3), mp8QAM(4), mp16QAM1(5), mp4QAM2(6), mp16QAM2(7), mp32QAM(8), mp64QAM(9), mp128QAM(10), mp256QAM(11)  

alMPActiveACM 1.3.6.1.4.1.12140.2.4.7
Activation ACM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPStatusACM 1.3.6.1.4.1.12140.2.4.8
Actual ACM status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), normal(0), low(1)  

alMPSupply 1.3.6.1.4.1.12140.2.5
OBJECT IDENTIFIER    

alMPInput 1.3.6.1.4.1.12140.2.5.1
Input voltage low.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), low(1)  

alMPRDG 1.3.6.1.4.1.12140.2.6
OBJECT IDENTIFIER    

alMPEEPROM 1.3.6.1.4.1.12140.2.6.1
EEPROM memory status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alMPRAM 1.3.6.1.4.1.12140.2.6.2
RAM memory status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), bad(1)  

alMPCommRMT 1.3.6.1.4.1.12140.2.6.3
Communication status with remote station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), error(1)  

alMPMUX 1.3.6.1.4.1.12140.2.7
OBJECT IDENTIFIER    

alMPBER 1.3.6.1.4.1.12140.2.7.1
Value of BER.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..30)  

alMPBER-10E6 1.3.6.1.4.1.12140.2.7.2
BER > 10E-6.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alMPBER-10E4 1.3.6.1.4.1.12140.2.7.3
BER > 10E-4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), no(0), yes(1)  

alMPFrame 1.3.6.1.4.1.12140.2.7.4
Frame LOSS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), ok(0), loss(1)  

alMPLine1 1.3.6.1.4.1.12140.2.8
OBJECT IDENTIFIER    

alMPLOSS1 1.3.6.1.4.1.12140.2.8.1
LOSS on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alMPILOSS1 1.3.6.1.4.1.12140.2.8.2
Ignore LOSS on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPAIS1 1.3.6.1.4.1.12140.2.8.3
AIS to line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alMPAISL1 1.3.6.1.4.1.12140.2.8.4
AIS from line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPLLB1 1.3.6.1.4.1.12140.2.8.5
Line loopback on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPRLB1 1.3.6.1.4.1.12140.2.8.6
Radio loopback on line 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPLine2 1.3.6.1.4.1.12140.2.9
OBJECT IDENTIFIER    

alMPLOSS2 1.3.6.1.4.1.12140.2.9.1
LOSS on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alMPILOSS2 1.3.6.1.4.1.12140.2.9.2
Ignore LOSS on line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPLink2 1.3.6.1.4.1.12140.2.9.3
Link status line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), down(0), up(1)  

alMPSpeed2 1.3.6.1.4.1.12140.2.9.4
Speed of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), e10Mbps(0), e100Mbps(1), e1000Mbps(2)  

alMPType2 1.3.6.1.4.1.12140.2.9.5
Communication type of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), halfduplex(0), fullduplex(1)  

alMPFlow2 1.3.6.1.4.1.12140.2.9.6
Flow control of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPPktRX2 1.3.6.1.4.1.12140.2.9.7
Received packets count of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPByteRX2 1.3.6.1.4.1.12140.2.9.8
Received bytes count of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPPktTX2 1.3.6.1.4.1.12140.2.9.9
Transmitted packets count of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPByteTX2 1.3.6.1.4.1.12140.2.9.10
Transmitted bytes count of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPError2 1.3.6.1.4.1.12140.2.9.11
Error count of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPCollision2 1.3.6.1.4.1.12140.2.9.12
Collision count of line 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPLine3 1.3.6.1.4.1.12140.2.10
OBJECT IDENTIFIER    

alMPLOSS3 1.3.6.1.4.1.12140.2.10.1
LOSS on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alMPILOSS3 1.3.6.1.4.1.12140.2.10.2
Ignore LOSS on line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPLink3 1.3.6.1.4.1.12140.2.10.3
Link status line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), down(0), up(1)  

alMPSpeed3 1.3.6.1.4.1.12140.2.10.4
Speed of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), e10Mbps(0), e100Mbps(1), e1000Mbps(2)  

alMPType3 1.3.6.1.4.1.12140.2.10.5
Communication type of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), halfduplex(0), fullduplex(1)  

alMPFlow3 1.3.6.1.4.1.12140.2.10.6
Flow control of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPPktRX3 1.3.6.1.4.1.12140.2.10.7
Received packets count of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPByteRX3 1.3.6.1.4.1.12140.2.10.8
Received bytes count of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPPktTX3 1.3.6.1.4.1.12140.2.10.9
Transmitted packets count of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPByteTX3 1.3.6.1.4.1.12140.2.10.10
Transmitted bytes count of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPError3 1.3.6.1.4.1.12140.2.10.11
Error count of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPCollision3 1.3.6.1.4.1.12140.2.10.12
Collision count of line 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPLine4 1.3.6.1.4.1.12140.2.11
OBJECT IDENTIFIER    

alMPLOSS4 1.3.6.1.4.1.12140.2.11.1
LOSS on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), not(0), yes(1)  

alMPILOSS4 1.3.6.1.4.1.12140.2.11.2
Ignore LOSS on line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPLink4 1.3.6.1.4.1.12140.2.11.3
Link status line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), down(0), up(1)  

alMPSpeed4 1.3.6.1.4.1.12140.2.11.4
Speed of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), e10Mbps(0), e100Mbps(1), e1000Mbps(2)  

alMPType4 1.3.6.1.4.1.12140.2.11.5
Communication type of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), halfduplex(0), fullduplex(1)  

alMPFlow4 1.3.6.1.4.1.12140.2.11.6
Flow control of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(-1), off(0), on(1)  

alMPPktRX4 1.3.6.1.4.1.12140.2.11.7
Received packets count of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPByteRX4 1.3.6.1.4.1.12140.2.11.8
Received bytes count of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPPktTX4 1.3.6.1.4.1.12140.2.11.9
Transmitted packets count of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPByteTX4 1.3.6.1.4.1.12140.2.11.10
Transmitted bytes count of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPError4 1.3.6.1.4.1.12140.2.11.11
Error count of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

alMPCollision4 1.3.6.1.4.1.12140.2.11.12
Collision count of line 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32