ALCATEL-IND1-TIMETRA-CHASSIS-MIB

File: ALCATEL-IND1-TIMETRA-CHASSIS-MIB.mib (248701 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
SNMP-FRAMEWORK-MIB	ALCATEL-IND1-TIMETRA-TC-MIB	ALCATEL-IND1-TIMETRA-GLOBAL-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Unsigned32	Integer32	Gauge32
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
TEXTUAL-CONVENTION	DateAndTime	RowStatus
TimeStamp	TimeInterval	TruthValue
MacAddress	RowPointer	DisplayString
SnmpAdminString	TmnxActionType	TmnxPortID
TItemDescription	TNamedItemOrEmpty	TNamedItem
TmnxOperState	TmnxAdminState	timetraSRMIBModules
tmnxSRObjs	tmnxSRNotifyPrefix	tmnxSRConfs

Defined Types

TmnxAlarmState
The TmnxAlarmState is an enumerated integer whose value indicates the current alarm state of a physical or logical component in the Alcatel 7x50 SR series system.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), alarmActive(1), alarmCleared(2)

TmnxChassisIndex
The TmnxChassisIndex is a unique index that identifies a chassis within an Alcatel 7x50 system. Note that initial releases will support only one chassis in a system.
TEXTUAL-CONVENTION
	INTEGER	1..32

TmnxHwIndex
The TmnxHwIndex is a unique integer index that identifies an Alcatel 7x50 SR series manufactured hardware component, such as an IOM, CPM, Fabric or MDA card.
TEXTUAL-CONVENTION
	Integer32	1..2147483647

TmnxHwIndexOrZero
The TmnxHwIndexOrZero is a unique integer index that identifies an Alcatel 7x50 SR series manufactured hardware component, such as an IOM, CPM, Fabric or MDA card. Also TmnxHwIndexOrZero can be zero.
TEXTUAL-CONVENTION
	Integer32	0..2147483647

TmnxHwClass
TmnxHwClass is an enumerated integer that identifies the general hardware type of a component in the tmnxHwTable.
TEXTUAL-CONVENTION
	INTEGER	other(1), unknown(2), chassis(3), container(4), powerSupply(5), fan(6), sensor(7), ioModule(8), cpmModule(9), fabricModule(10), mdaModule(11), flashDiskModule(12), port(13), mcm(14), ccm(15)

TmnxCardType
The TmnxCardType data type is a bit-mask field that describes the various Alcatel 7x50 SR series card types. A TmnxCardType bit value specifies the index value for the entry in the tmnxCardTypeTable used to identify a specific type of card manufactured by Alcatel. When multiple bits are set, it can be used to identify a set or list of card types used in the tmnxCardTable and tmnxCpmCardTable to indicate supported or allowed cards within a specific chassis slot. Some example card types might be: sfm-400g -- 400g CPM/SF module sfm-200g -- 200g CPM/SF module sfm-100g -- 100g CPM/SF module iom-20g -- 2 x 10-Gig MDA IOM Card
TEXTUAL-CONVENTION
	Unsigned32

TmnxChassisType
The TmnxChassisType data type is an integer that specifies the index value for the entry in the tmnxChassisTypeTable used to identify a specific type of chassis backplane manufactured by Alcatel.
TEXTUAL-CONVENTION
	Unsigned32

TmnxDeviceState
The TmnxDeviceState data type is an enumerated integer that describes the values used to identify states of chassis components such as fans and power supplies.
TEXTUAL-CONVENTION
	INTEGER	deviceStateUnknown(1), deviceNotEquipped(2), deviceStateOk(3), deviceStateFailed(4), deviceStateOutOfService(5)

TmnxLEDState
The TmnxLEDState data type is an enumerated integer that describes the values used to identify state LEDs on Alcatel 7x50 SR series cards.
TEXTUAL-CONVENTION
	INTEGER	ledOff(1), ledRed(2), ledAmber(3), ledYellow(4), ledGreen(5), ledAmberBlink(6), ledYellowBlink(7), ledGreenBlink(8)

TmnxMdaType
The TmnxMdaType data type is an integer that used to identify the kind of Media Dependent Adapter (MDA) installed on a card. The value of TmnxMdaType corresponds to the bit number indicated by TmnxMDASuppType. A TmnxMdaType value specifies the index value for the entry in the tmnxMdaTypeTable used to identify a specific type of MDA manufactured by Alcatel.
TEXTUAL-CONVENTION
	Unsigned32

TmnxMDASuppType
The TmnxMDASuppType data type is a SNMP BIT that is used to identify the kind of Media Dependent Adapter (MDA) supported on a card. When multiple bits are set, it can be used to identify a set or list of supported MDAs within a specific card slot. The MDA types are defined in the tmnxMdaTypeTable.
TEXTUAL-CONVENTION
	BITS	invalid-MDA-type(0), unassigned(1), supp-MDA-type-2(2), supp-MDA-type-3(3), supp-MDA-type-4(4), supp-MDA-type-5(5), supp-MDA-type-6(6), supp-MDA-type-7(7), supp-MDA-type-8(8), supp-MDA-type-9(9), supp-MDA-type-10(10), supp-MDA-type-11(11), supp-MDA-type-12(12), supp-MDA-type-13(13), supp-MDA-type-14(14), supp-MDA-type-15(15), supp-MDA-type-16(16), supp-MDA-type-17(17), supp-MDA-type-18(18), supp-MDA-type-19(19), supp-MDA-type-20(20), supp-MDA-type-21(21), supp-MDA-type-22(22), supp-MDA-type-23(23), supp-MDA-type-24(24), supp-MDA-type-25(25), supp-MDA-type-26(26), supp-MDA-type-27(27), supp-MDA-type-28(28), supp-MDA-type-29(29), supp-MDA-type-30(30), supp-MDA-type-31(31), supp-MDA-type-32(32), supp-MDA-type-33(33), supp-MDA-type-34(34), supp-MDA-type-35(35), supp-MDA-type-36(36), supp-MDA-type-37(37), supp-MDA-type-38(38), supp-MDA-type-39(39), supp-MDA-type-40(40), supp-MDA-type-41(41), supp-MDA-type-42(42), supp-MDA-type-43(43), supp-MDA-type-44(44), supp-MDA-type-45(45), supp-MDA-type-46(46), supp-MDA-type-47(47)

TmnxMDAChanType
The TmnxMDAChanType data type indicates the type of channel that can be created on an MDA.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), sonetSts768(1), sonetSts192(2), sonetSts48(3), sonetSts12(4), sonetSts3(5), sonetSts1(6), sdhTug3(7), sonetVtg(8), sonetVt15(9), sonetVt2(10), sonetVt3(11), sonetVt6(12), pdhTu3(13), pdhDs3(14), pdhE3(15), pdhDs1(16), pdhE1(17), pdhDs0Grp(18)

TmnxCcmType
The TmnxCcmType data type is bit-mask field that describes the values used to identify the kind of Chassis Control module (CCM) installed on the chassis. A TmnxCcmType bit value specifies the index value for the entry in the tmnxCcmTypeTable used to identify a specific type of CCM manufactured by Alcatel. When multiple bits are set, it can be used to identify a set or list of CCM types used in the tmnxCcmTable to indicate supported CCMs within a specific chassis slot. Some example CCM types are: unknown -- unknown/uninstalled ccm-v1 -- Chassis Control Module version 1
TEXTUAL-CONVENTION
	Unsigned32

TmnxMcmType
The TmnxMcmType data type is bit-mask field that describes the values used to identify the kind of MDA Carrier module (MCM) installed on the chassis. A TmnxMcmType bit value specifies the index value for the entry in the tmnxMcmTypeTable used to identify a specific type of MCM manufactured by Alcatel. When multiple bits are set, it can be used to identify a set or list of MCM types used in the tmnxMcmTable to indicate supported MCMs within a specific card slot. Some example MCM types are: unknown -- unknown/uninstalled mcm-v1 -- MDA Carrier Module version 1
TEXTUAL-CONVENTION
	Unsigned32

TmnxSlotNum
The TmnxSlotNum data type is an integer that specifies a slot in an Alcatel 7x50 SR series chassis.
TEXTUAL-CONVENTION
	INTEGER	1..128

TmnxSlotNumOrZero
The TmnxSlotNumOrZero data type is an integer that specifies a slot in an Alcatel 7x50 SR series chassis or zero.
TEXTUAL-CONVENTION
	INTEGER	0..128

TmnxPortAdminStatus
The desired administrative status of this port.
TEXTUAL-CONVENTION
	INTEGER	noop(1), inService(2), outOfService(3), diagnose(4)

TmnxChassisMode
The TmnxChassisMode data type is an enumerated integer that specifies the values used to identify which set of scaling numbers and features are effective for an Alcatel 7x50 SR series chassis. 'modeA' corresponds to the scaling and feature set on the existing iom-20g. 'modeB' corresponds to the scaling and features that come with iom-20g-b. 'modeC' corresponds to the scaling and features that come with iom2-20g.
TEXTUAL-CONVENTION
	INTEGER	modeA(1), modeB(2), modeC(3)

TmnxSETSRefSource
The TmnxSETSRefSource data type is an enumerated integer that describes the values used to identify the Synchronous Equipment Timing Subsystem (SETS) timing reference source.
TEXTUAL-CONVENTION
	INTEGER	reference1(1), reference2(2), bits(3)

TmnxSETSRefQualified
The TmnxSETSRefQualified data type is an enumerated integer that describes the values used to identify whether the reference is 'qualified' or 'not-qualified' for use by SETS.
TEXTUAL-CONVENTION
	INTEGER	qualified(1), not-qualified(2)

TmnxSETSRefAlarm
The TmnxSETSRefAlarm data type is a bitmap that describes the values used to identify the alarms on the SETS timing reference source if the source is 'not-qualified'. 'los' - loss of signal 'oof' - out of frequency range 'oopir' - out of pull in range.
TEXTUAL-CONVENTION
	BITS	los(0), oof(1), oopir(2)

TmnxBITSIfType
The TmnxBITSIfType data type is an enumerated integer that describes the values used to identify the interface and framing types of a BITS (Building Integrated Timing Supply) interface.
TEXTUAL-CONVENTION
	INTEGER	none(0), t1-esf(1), t1-sf(2), e1-pcm30crc(3), e1-pcm31crc(4)

TmnxCcagId
TmnxCcagId is an integer specifying the cross connect aggregation group. The value '0' is used when a ccag is not defined and is not a valid value when TmnxCcagId is used as an index.
TEXTUAL-CONVENTION
	Integer32	0 | 1..8

TmnxCcagRate
TmnxCcagRate is an integer specifying the rate for a CCAG member in Kbps. The range of TmnxCcagRate is from 0 Kbps to 100Gbps. The value '-1' is used for maximum rate available.
TEXTUAL-CONVENTION
	Integer32	-1 | 0..100000000

TmnxCcagRateOption
TmnxCcagRateOption specifies how the defined rate is applied to active Cross Connect Adaptors (CCAs). aggregate (1) - the defined rate is equally divided among the CCAs in the CCAG member list based on the number of active CCAs. cca (2) - the defined rate is applied to all CCAs in the CCAG member list.
TEXTUAL-CONVENTION
	INTEGER	aggregate(1), cca(2)

TmnxChassisEntry
SEQUENCE
	tmnxChassisIndex	TmnxChassisIndex
	tmnxChassisRowStatus	RowStatus
	tmnxChassisName	TNamedItemOrEmpty
	tmnxChassisType	TmnxChassisType
	tmnxChassisLocation	TItemDescription
	tmnxChassisCoordinates	TItemDescription
	tmnxChassisNumSlots	Unsigned32
	tmnxChassisNumPorts	Unsigned32
	tmnxChassisNumPwrSupplies	Unsigned32
	tmnxChassisNumFanTrays	Unsigned32
	tmnxChassisNumFans	Unsigned32
	tmnxChassisCriticalLEDState	TmnxLEDState
	tmnxChassisMajorLEDState	TmnxLEDState
	tmnxChassisMinorLEDState	TmnxLEDState
	tmnxChassisBaseMacAddress	MacAddress
	tmnxChassisCLLICode	DisplayString
	tmnxChassisReboot	TmnxActionType
	tmnxChassisUpgrade	TmnxActionType
	tmnxChassisAdminMode	TmnxChassisMode
	tmnxChassisOperMode	TmnxChassisMode
	tmnxChassisModeForce	TmnxActionType
	tmnxChassisUpdateWaitTime	Unsigned32
	tmnxChassisUpdateTimeLeft	Unsigned32
	tmnxChassisOverTempState	INTEGER

TmnxChassisFanEntry
SEQUENCE
	tmnxChassisFanIndex	Unsigned32
	tmnxChassisFanOperStatus	TmnxDeviceState
	tmnxChassisFanSpeed	INTEGER

TmnxChassisPowerSupplyEntry
SEQUENCE
	tmnxChassisPowerSupplyId	Unsigned32
	tmnxChassisPowerSupplyACStatus	TmnxDeviceState
	tmnxChassisPowerSupplyDCStatus	TmnxDeviceState
	tmnxChassisPowerSupplyTempStatus	TmnxDeviceState
	tmnxChassisPowerSupplyTempThreshold	Integer32
	tmnxChassisPowerSupply1Status	TmnxDeviceState
	tmnxChassisPowerSupply2Status	TmnxDeviceState
	tmnxChassisPowerSupplyAssignedType	INTEGER
	tmnxChassisPowerSupplyInputStatus	TmnxDeviceState
	tmnxChassisPowerSupplyOutputStatus	TmnxDeviceState

TmnxChassisTypeEntry
SEQUENCE
	tmnxChassisTypeIndex	TmnxChassisType
	tmnxChassisTypeName	TNamedItemOrEmpty
	tmnxChassisTypeDescription	TItemDescription
	tmnxChassisTypeStatus	TruthValue

TmnxHwEntry
SEQUENCE
	tmnxHwIndex	TmnxHwIndex
	tmnxHwID	RowPointer
	tmnxHwMfgString	SnmpAdminString
	tmnxHwMfgBoardNumber	OCTET STRING
	tmnxHwSerialNumber	SnmpAdminString
	tmnxHwManufactureDate	SnmpAdminString
	tmnxHwClass	TmnxHwClass
	tmnxHwName	TNamedItemOrEmpty
	tmnxHwAlias	TNamedItemOrEmpty
	tmnxHwAssetID	SnmpAdminString
	tmnxHwCLEI	SnmpAdminString
	tmnxHwIsFRU	TruthValue
	tmnxHwContainedIn	Integer32
	tmnxHwParentRelPos	Integer32
	tmnxHwAdminState	INTEGER
	tmnxHwOperState	INTEGER
	tmnxHwTempSensor	TruthValue
	tmnxHwTemperature	Integer32
	tmnxHwTempThreshold	Integer32
	tmnxHwBootCodeVersion	DisplayString
	tmnxHwSoftwareCodeVersion	DisplayString
	tmnxHwSwLastBoot	DateAndTime
	tmnxHwSwState	INTEGER
	tmnxHwAlarmState	TmnxAlarmState
	tmnxHwLastAlarmEvent	RowPointer
	tmnxHwClearAlarms	TmnxActionType
	tmnxHwSwImageSource	INTEGER
	tmnxHwMfgDeviations	SnmpAdminString
	tmnxHwBaseMacAddress	MacAddress
	tmnxHwFailureReason	DisplayString

TmnxHwContainsEntry
SEQUENCE
	tmnxHwContainedIndex	TmnxHwIndex

TmnxCcmEntry
SEQUENCE
	tmnxCcmIndex	Unsigned32
	tmnxCcmOperStatus	TmnxDeviceState
	tmnxCcmHwIndex	TmnxHwIndex
	tmnxCcmEquippedType	TmnxCcmType

TmnxCcmTypeEntry
SEQUENCE
	tmnxCcmTypeIndex	TmnxCcmType
	tmnxCcmTypeName	TNamedItemOrEmpty
	tmnxCcmTypeDescription	TItemDescription
	tmnxCcmTypeStatus	TruthValue

TmnxCardEntry
SEQUENCE
	tmnxCardSlotNum	TmnxSlotNum
	tmnxCardSupportedTypes	TmnxCardType
	tmnxCardAllowedTypes	TmnxCardType
	tmnxCardAssignedType	TmnxCardType
	tmnxCardEquippedType	TmnxCardType
	tmnxCardHwIndex	TmnxHwIndex
	tmnxCardClockSource	TItemDescription
	tmnxCardNumMdaSlots	Unsigned32
	tmnxCardNumMdas	Unsigned32
	tmnxCardReboot	TmnxActionType
	tmnxCardMemorySize	Unsigned32
	tmnxCardNamedPoolAdminMode	TmnxAdminState
	tmnxCardNamedPoolOperMode	TmnxAdminState

TmnxCpmCardEntry
SEQUENCE
	tmnxCpmCardSlotNum	TmnxSlotNum
	tmnxCpmCardNum	Unsigned32
	tmnxCpmCardSupportedTypes	TmnxCardType
	tmnxCpmCardAllowedTypes	TmnxCardType
	tmnxCpmCardAssignedType	TmnxCardType
	tmnxCpmCardEquippedType	TmnxCardType
	tmnxCpmCardHwIndex	TmnxHwIndex
	tmnxCpmCardBootOptionVersion	TItemDescription
	tmnxCpmCardBootOptionLastModified	DateAndTime
	tmnxCpmCardConfigBootedVersion	TItemDescription
	tmnxCpmCardIndexBootedVersion	TItemDescription
	tmnxCpmCardConfigLastModified	DateAndTime
	tmnxCpmCardConfigLastSaved	DateAndTime
	tmnxCpmCardRedundant	INTEGER
	tmnxCpmCardClockSource	TItemDescription
	tmnxCpmCardNumCpus	Unsigned32
	tmnxCpmCardCpuType	INTEGER
	tmnxCpmCardMemorySize	Unsigned32
	tmnxCpmCardSwitchToRedundantCard	TmnxActionType
	tmnxCpmCardReboot	TmnxActionType
	tmnxCpmCardRereadBootOptions	TmnxActionType
	tmnxCpmCardConfigFileLastBooted	DisplayString
	tmnxCpmCardConfigFileLastSaved	DisplayString
	tmnxCpmCardConfigFileLastBootedHeader	OCTET STRING
	tmnxCpmCardIndexFileLastBootedHeader	OCTET STRING
	tmnxCpmCardBootOptionSource	DisplayString
	tmnxCpmCardConfigSource	INTEGER
	tmnxCpmCardBootOptionLastSaved	DateAndTime
	tmnxCpmCardMasterSlaveRefState	INTEGER

TmnxFabricEntry
SEQUENCE
	tmnxFabricSlotNum	Unsigned32
	tmnxFabricAssignedType	TmnxCardType
	tmnxFabricEquippedType	TmnxCardType
	tmnxFabricHwIndex	TmnxHwIndex

TmnxCpmFlashEntry
SEQUENCE
	tmnxCpmFlashId	Unsigned32
	tmnxCpmFlashOperStatus	TmnxDeviceState
	tmnxCpmFlashSerialNumber	TItemDescription
	tmnxCpmFlashFirmwareRevision	TItemDescription
	tmnxCpmFlashModelNumber	TItemDescription
	tmnxCpmFlashCapacity	Unsigned32
	tmnxCpmFlashUsed	Unsigned32
	tmnxCpmFlashHwIndex	TmnxHwIndex

TmnxMDAEntry
SEQUENCE
	tmnxMDASlotNum	Unsigned32
	tmnxMDASupportedTypes	TmnxMDASuppType
	tmnxMDAAllowedTypes	TmnxMdaType
	tmnxMDAAssignedType	TmnxMdaType
	tmnxMDAEquippedType	TmnxMdaType
	tmnxMDAHwIndex	TmnxHwIndex
	tmnxMDAMaxPorts	INTEGER
	tmnxMDAEquippedPorts	Unsigned32
	tmnxMDATxTimingSelected	INTEGER
	tmnxMDASyncIfTimingStatus	INTEGER
	tmnxMDANetworkIngQueues	TNamedItem
	tmnxMDACapabilities	BITS
	tmnxMDAMinChannelization	TmnxMDAChanType
	tmnxMDAMaxChannelization	TmnxMDAChanType
	tmnxMDAMaxChannels	Unsigned32
	tmnxMDAChannelsInUse	Unsigned32
	tmnxMDACcagId	TmnxCcagId
	tmnxMDAReboot	TmnxActionType
	tmnxMDAHiBwMcastSource	TruthValue
	tmnxMDAHiBwMcastAlarm	TruthValue
	tmnxMDAHiBwMcastTapCount	Gauge32
	tmnxMDAHiBwMcastGroup	Unsigned32
	tmnxMDAClockMode	INTEGER
	tmnxMDADiffTimestampFreq	Unsigned32
	tmnxMDAMcPathMgmtBwPlcyName	TNamedItem
	tmnxMDAMcPathMgmtPriPathLimit	Unsigned32
	tmnxMDAMcPathMgmtSecPathLimit	Unsigned32
	tmnxMDAMcPathMgmtAncPathLimit	Unsigned32
	tmnxMDAMcPathMgmtAdminState	TmnxAdminState
	tmnxMDAIngNamedPoolPolicy	TNamedItemOrEmpty
	tmnxMDAEgrNamedPoolPolicy	TNamedItemOrEmpty
	tmnxMDAMcPathMgmtPriInUseBw	Gauge32
	tmnxMDAMcPathMgmtSecInUseBw	Gauge32
	tmnxMDAMcPathMgmtAncInUseBw	Gauge32
	tmnxMDAMcPathMgmtBlkHoleInUseBw	Gauge32

TmnxCardTypeEntry
SEQUENCE
	tmnxCardTypeIndex	TmnxCardType
	tmnxCardTypeName	TNamedItemOrEmpty
	tmnxCardTypeDescription	TItemDescription
	tmnxCardTypeStatus	TruthValue

TmnxMdaTypeEntry
SEQUENCE
	tmnxMdaTypeIndex	TmnxMdaType
	tmnxMdaTypeName	TNamedItemOrEmpty
	tmnxMdaTypeDescription	TItemDescription
	tmnxMdaTypeStatus	TruthValue

TmnxSyncIfTimingEntry
SEQUENCE
	tmnxSyncIfTimingRevert	TruthValue
	tmnxSyncIfTimingRefOrder1	TmnxSETSRefSource
	tmnxSyncIfTimingRefOrder2	TmnxSETSRefSource
	tmnxSyncIfTimingRef1SrcPort	TmnxPortID
	tmnxSyncIfTimingRef1AdminStatus	TmnxPortAdminStatus
	tmnxSyncIfTimingRef1InUse	TruthValue
	tmnxSyncIfTimingRef1Qualified	TmnxSETSRefQualified
	tmnxSyncIfTimingRef1Alarm	TmnxSETSRefAlarm
	tmnxSyncIfTimingRef2SrcPort	TmnxPortID
	tmnxSyncIfTimingRef2AdminStatus	TmnxPortAdminStatus
	tmnxSyncIfTimingRef2InUse	TruthValue
	tmnxSyncIfTimingRef2Qualified	TmnxSETSRefQualified
	tmnxSyncIfTimingRef2Alarm	TmnxSETSRefAlarm
	tmnxSyncIfTimingFreqOffset	Integer32
	tmnxSyncIfTimingStatus	INTEGER
	tmnxSyncIfTimingRefOrder3	TmnxSETSRefSource
	tmnxSyncIfTimingBITSIfType	TmnxBITSIfType
	tmnxSyncIfTimingBITSAdminStatus	TmnxPortAdminStatus
	tmnxSyncIfTimingBITSInUse	TruthValue
	tmnxSyncIfTimingBITSQualified	TmnxSETSRefQualified
	tmnxSyncIfTimingBITSAlarm	TmnxSETSRefAlarm
	tmnxSyncIfTimingRef1SrcHw	TmnxHwIndexOrZero
	tmnxSyncIfTimingRef1BITSIfType	TmnxBITSIfType
	tmnxSyncIfTimingRef2SrcHw	TmnxHwIndexOrZero
	tmnxSyncIfTimingRef2BITSIfType	TmnxBITSIfType

TSyncIfTimingAdmEntry
SEQUENCE
	tSyncIfTimingAdmRevert	TruthValue
	tSyncIfTimingAdmRefOrder1	TmnxSETSRefSource
	tSyncIfTimingAdmRefOrder2	TmnxSETSRefSource
	tSyncIfTimingAdmRef1SrcPort	TmnxPortID
	tSyncIfTimingAdmRef1AdminStatus	TmnxPortAdminStatus
	tSyncIfTimingAdmRef2SrcPort	TmnxPortID
	tSyncIfTimingAdmRef2AdminStatus	TmnxPortAdminStatus
	tSyncIfTimingAdmChanged	Unsigned32
	tSyncIfTimingAdmRefOrder3	TmnxSETSRefSource
	tSyncIfTimingAdmBITSIfType	TmnxBITSIfType
	tSyncIfTimingAdmBITSAdminStatus	TmnxPortAdminStatus
	tSyncIfTimingAdmRef1SrcHw	TmnxHwIndexOrZero
	tSyncIfTimingAdmRef1BITSIfType	TmnxBITSIfType
	tSyncIfTimingAdmRef2SrcHw	TmnxHwIndexOrZero
	tSyncIfTimingAdmRef2BITSIfType	TmnxBITSIfType

TmnxCcagEntry
SEQUENCE
	tmnxCcagId	TmnxCcagId
	tmnxCcagRowStatus	RowStatus
	tmnxCcagLastChanged	TimeStamp
	tmnxCcagDescription	DisplayString
	tmnxCcagAdminStatus	TmnxAdminState
	tmnxCcagOperStatus	TmnxOperState
	tmnxCcagCcaRate	TmnxCcagRate
	tmnxCcagAccessAdaptQos	INTEGER

TmnxCcagPathEntry
SEQUENCE
	tmnxCcagPathId	INTEGER
	tmnxCcagPathLastChanged	TimeStamp
	tmnxCcagPathRate	TmnxCcagRate
	tmnxCcagPathRateOption	TmnxCcagRateOption
	tmnxCcagPathWeight	Unsigned32

TmnxCcagPathCcEntry
SEQUENCE
	tmnxCcagPathCcType	INTEGER
	tmnxCcagPathCcLastChanged	TimeStamp
	tmnxCcagPathCcEgrPoolResvCbs	INTEGER
	tmnxCcagPathCcEgrPoolSlpPlcy	TNamedItem
	tmnxCcagPathCcIngPoolResvCbs	INTEGER
	tmnxCcagPathCcIngPoolSlpPlcy	TNamedItem
	tmnxCcagPathCcAcctPolicyId	Unsigned32
	tmnxCcagPathCcCollectStats	TruthValue
	tmnxCcagPathCcQueuePlcy	TNamedItem
	tmnxCcagPathCcMac	MacAddress
	tmnxCcagPathCcMtu	Unsigned32
	tmnxCcagPathCcUserAssignedMac	TruthValue
	tmnxCcagPathCcHwMac	MacAddress

TmnxMcmEntry
SEQUENCE
	tmnxMcmSlotNum	Unsigned32
	tmnxMcmSupportedTypes	TmnxMcmType
	tmnxMcmAssignedType	TmnxMcmType
	tmnxMcmEquippedType	TmnxMcmType
	tmnxMcmHwIndex	TmnxHwIndex

TmnxMcmTypeEntry
SEQUENCE
	tmnxMcmTypeIndex	TmnxMcmType
	tmnxMcmTypeName	TNamedItemOrEmpty
	tmnxMcmTypeDescription	TItemDescription
	tmnxMcmTypeStatus	TruthValue

Defined Values

tmnxChassisMIBModule		1.3.6.1.4.1.6527.1.1.3.2
This document is the SNMP MIB module to manage and provision the hardware components of the Alcatel 7x50 device. Copyright 2003-2008 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY

tmnxHwObjs		1.3.6.1.4.1.6527.3.1.2.2
OBJECT IDENTIFIER

tmnxChassisObjs		1.3.6.1.4.1.6527.3.1.2.2.1
OBJECT IDENTIFIER

tmnxSlotObjs		1.3.6.1.4.1.6527.3.1.2.2.2
OBJECT IDENTIFIER

tmnxCardObjs		1.3.6.1.4.1.6527.3.1.2.2.3
OBJECT IDENTIFIER

tmnxChassisNotificationObjects		1.3.6.1.4.1.6527.3.1.2.2.6
OBJECT IDENTIFIER

tmnxChassisAdminObjects		1.3.6.1.4.1.6527.3.1.2.2.8
OBJECT IDENTIFIER

tmnxHwNotification		1.3.6.1.4.1.6527.3.1.3.2
OBJECT IDENTIFIER

tmnxChassisNotifyPrefix		1.3.6.1.4.1.6527.3.1.3.2.1
OBJECT IDENTIFIER

tmnxChassisNotification		1.3.6.1.4.1.6527.3.1.3.2.1.0
OBJECT IDENTIFIER

tmnxHwConformance		1.3.6.1.4.1.6527.3.1.1.2
OBJECT IDENTIFIER

tmnxChassisConformance		1.3.6.1.4.1.6527.3.1.1.2.1
OBJECT IDENTIFIER

tmnxChassisTotalNumber		1.3.6.1.4.1.6527.3.1.2.2.1.1
The number of chassis installed in this system. For the first release of the Alcatel 7x50 series product, there is only 1 chassis per system. A multi-chassis system model is supported to allow for future product expansion.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..32

tmnxChassisLastChange		1.3.6.1.4.1.6527.3.1.2.2.1.2
The value of sysUpTime when the tmnxChassisTable was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxChassisTable		1.3.6.1.4.1.6527.3.1.2.2.1.3
The chassis table has an entry for each chassis in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxChassisEntry

tmnxChassisEntry		1.3.6.1.4.1.6527.3.1.2.2.1.3.1
Each row entry represents a chassis in the system. The agent creates the row for the first chassis in the system, with tmnxChassisIndex = 1, which is auto-discovered by the active CPM card. Additional chassis entries can be created and deleted via SNMP SET operations. Creation requires a SET request containing at least tmnxChassisAdminMode and tmnxChassisRowStatus. Note that the first Alcatel 7x50 series product release does not support multiple chassis, therefore there will not be more than one row entry in this table; attempts to create additional rows in this table will be denied.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxChassisEntry

tmnxChassisIndex		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.1
The unique value which identifies this chassis in the system. The first release of the product only supports a single chassis in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxChassisIndex

tmnxChassisRowStatus		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.2
The row status. The creation or deletion of a chassis entry causes creation or deletion of corresponding entries in the tmnxCardTable with the same tmnxChassisIndex value. Note, the agent will disallow chassis deletion if its entries in the card table have not first been put into the proper state for removal. The row entry for tmnxChassisIndex equal 1 cannot be deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxChassisName		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.3
The administrative name assigned this chassis. Setting tmnxChassisName to the empty string, ''H, resets tmnxChassisName to the TiMOS default value.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxChassisType		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.4
The type of chassis used in this Alcatel 7x50 system. The value of tmnxChassisType is the tmnxChassisTypeIndex for the entry in the tmnxChassisTypeTable that represents the Alcatel 7x50 SR series chassis model for this system. Chassis types are distinguished by their backplane type.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxChassisType

tmnxChassisLocation		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.5
A user supplied string that indicates the on site location of this chassis. This could used for a Common Language Location Identifier, CLLI, code string if desired. A CLLI code is an 11-character standardized geographic identifier that uniquely identifies the geographic location of places and certain functional categories of equipment unique to the telecommunications industry. All valid CLLI codes are created, updated and maintained in the Central Location Online Entry System (CLONES) database.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxChassisCoordinates		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.6
A user supplied string that indicates the Global Positioning System (GPS) coordinates for the location of this chassis. N 45 58 23, W 34 56 12 N37 37' 00 latitude, W122 22' 00 longitude N36*39.246' W121*40.121' Two-dimensional GPS positioning offers latitude and longitude information as a four dimensional vector: where Direction is one of the four basic values: N, S, W, E; hours ranges from 0 to 180 (for latitude) and 0 to 90 for longitude, and, finally, minutes and seconds range from 0 to 60. Thus is an example of longitude and is an example of latitude. Four bytes of addressing space (one byte for each of the four dimensions) are necessary to store latitude and four bytes are also sufficient to store longitude. Thus eight bytes total are necessary to address the whole surface of earth with precision down to 0.1 mile! Notice that if we desired precision down to 0.001 mile (1.8 meters) then we would need just five bytes for each component, or ten bytes together for the full address (as military versions provide).
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxChassisNumSlots		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.7
The number of slots in this chassis that are available for plug-in cards. This includes both fabric and IOM cards
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxChassisNumPorts		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.8
The total number of ports currently installed in this chassis. This count does not include the Ethernet ports on the CPM cards that are used for management access.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxChassisNumPwrSupplies		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.9
The total number of power supplies installed in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxChassisNumFanTrays		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.10
The total number of fan trays installed in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxChassisNumFans		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.11
The total number of fans installed in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxChassisCriticalLEDState		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.12
The current state of the Critical LED in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxLEDState

tmnxChassisMajorLEDState		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.13
The current state of the Major LED in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxLEDState

tmnxChassisMinorLEDState		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.14
The current state of the Minor LED in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxLEDState

tmnxChassisBaseMacAddress		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.15
The base chassis ethernet MAC address. Special purpose MAC addresses used by the system software are constructed as offsets from this base address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

tmnxChassisCLLICode		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.16
A Common Language Location Identifier (CLLI) code is an 11-character standardized geographic identifier that uniquely identifies the geographic location of places and certain functional categories of equipment unique to the telecommunications industry. If the set on this object specifies a non-null string, the string will automatically be truncated or padded(with spaces) to 11 characters.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

tmnxChassisReboot		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.17
Setting this tmnxChassisReboot to 'doAction' causes a soft-reboot of the entire chassis including all the CPM and IOM cards. Note that the reboot action is likely to occur before the SNMP SET response can be transmitted.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxActionType

tmnxChassisUpgrade		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.18
Setting this tmnxChassisUpgrade to 'doAction' causes an upgrade of all firmware and a reboot of the entire chassis including all the CPM and IOM cards. CAUTION: This upgrade and reboot may take several minutes to complete. The chassis MUST NOT be reset or powered down, nor cards inserted or removed, during this process. Any of these prohibited actions may cause the cards to be rendered inoperable. tmnxChassisUpgrade and tmnxChassisReboot must be set together in the same SNMP SET request PDU or else the SET request will fail with an inconsistentValue error. Note that the reboot action is likely to occur before the SNMP SET response can be transmitted.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxActionType

tmnxChassisAdminMode		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.19
The value of tmnxChassisAdminMode specifies the scaling and feature set for the IOM cards in the chassis. Setting this variable to 'modeA' causes all IOM cards in the chassis to use the scaling and feature sets supported on the iom-20g card type. Setting tmnxChassisAdminMode to 'modeB' corresponds to the scaling and feature sets supported on the iom-20g-b card type. 'modeC' corresponds to the scaling and feature sets supported on the iom2-20g card type. An attempt to change the value of tmnxChassisAdminMode from 'modeA' to 'modeB' (upgrade) or 'modeC' (upgrade) without also setting tmnxChassisModeForce to a value of 'doAction' in the same SNMP SET request, will fail with an inconsistentValue error if there are any IOM cards in the chassis with a value of 'iom-20g' for tmnxCardAssignedType. An attempt to change the value of tmnxChassisAdminMode from 'modeB' to 'modeC' (upgrade) without also setting tmnxChassisModeForce to a value of 'doAction' in the same SNMP SET request, will fail with an inconsistentValue error if there are any IOM cards in the chassis with a value of 'iom-20g-b' for tmnxCardAssignedType. 'modeB' scaling and feature sets cannot be supported on the iom-20g card. 'modeC' scaling feature set cannot be supported on either on the iom-20g or the iom-20g-b.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxChassisMode

tmnxChassisOperMode		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.20
The value of tmnxChassisOperMode indicates the operational scaling and feature set for the IOM cards in the chassis. Changing the value of tmnxChassisAdminMode from 'modeB' to 'modeA' (downgrade) will result in tmnxChassisAdminMode indicating 'modeA' while tmnxChassisOperMode indicates 'modeB' untill the configuration is saved and the system rebooted, at which point, the actual downgrade will take effect. Changing the value of tmnxChassisAdminMode from 'modeC' to either 'modeB' (downgrade) or 'modeA' (downgrade) will result in tmnxChassisAdminMode indicating 'modeB' or 'modeA' respectively while tmnxChassisOperMode indicates 'modeC' untill the configuration is saved and the system rebooted, at which point, the actual downgrade will take effect. 'modeB' scaling and feature sets cannot be supported on the iom-20g card. 'modeC' scaling feature set cannot be supported on either on the iom-20g or the iom-20g-b.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxChassisMode

tmnxChassisModeForce		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.21
Setting tmnxChassisModeForce to a value of 'doAction' in the same SNMP SET request where tmnxChassisAdminMode is set to 'modeB' allows the chassis to be upgraded to 'modeB' even if there are IOM cards in the chassis with a value of 'iom-20g' for tmnxCardAssignedType. Setting tmnxChassisModeForce to a value of 'doAction' in the same SNMP SET request where tmnxChassisAdminMode is set to 'modeC' allows the chassis to be upgraded to 'modeC' even if there are IOM cards in the chassis with a value of 'iom2-20g' for tmnxCardAssignedType. An attempt to set tmnxChassisModeForce to 'doAction' without also setting tmnxChassisAdminMode, in the same SNMP SET request will fail with an inconsistentValue error. ----------------------------------------------------------------------- Mode change | Assigned card | Force | Result ----------------------------------------------------------------------- a to b (upgrade) | iom-20g | not-set | error a to b (upgrade) | iom-20g | set | mode b with warnings a to b (upgrade) | iom-20g-b | not-set | mode b a to b (upgrade) | iom-20g-b | set | mode b a to c (upgrade) | iom-20g | not-set | error a to c (upgrade) | iom-20g | set | mode c with warnings a to c (upgrade) | iom2-20g | not-set | mode c a to c (upgrade) | iom2-20g | set | mode c b to c (upgrade) | iom-20g-b | not-set | error b to c (upgrade) | iom-20g-b | set | mode c with warnings b to c (upgrade) | iom2-20g | not-set | mode c b to c (upgrade) | iom2-20g | set | mode c b to a (downgrade)| iom-20g | not-set | mode a on save and reboot b to a (downgrade)| iom-20g | set | mode a on save and reboot b to a (downgrade)| iom-20g-b | not-set | mode a on save and reboot b to a (downgrade)| iom-20g-b | set | mode a on save and reboot c to a (downgrade)| iom-20g | not-set | mode a on save and reboot c to a (downgrade)| iom-20g | set | mode a on save and reboot c to a (downgrade)| iom2-20g | not-set | mode a on save and reboot c to a (downgrade)| iom2-20g | set | mode a on save and reboot c to b (downgrade)| iom-20g-b | not-set | mode b on save and reboot c to b (downgrade)| iom-20g-b | set | mode b on save and reboot c to b (downgrade)| iom2-20g | not-set | mode b on save and reboot c to b (downgrade)| iom2-20g | set | mode b on save and reboot -----------------------------------------------------------------------
Status: current	Access: read-create
OBJECT-TYPE
	TmnxActionType

tmnxChassisUpdateWaitTime		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.22
The value of tmnxChassisUpdateWaitTime specifies the time to wait before rebooting IOM cards running older software versions following a software upgrade or downgrade activity switchover. This object was obsoleted in release 5.0.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Unsigned32	15..600

tmnxChassisUpdateTimeLeft		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.23
Following a software upgrade or downgrade activity switchover, the value of tmnxChassisUpdateTimeLeft indicates the time remaining before IOM cards or MDAs running older software versions will be rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxChassisOverTempState		1.3.6.1.4.1.6527.3.1.2.2.1.3.1.24
The current Over Temperature state of this chassis. stateOk Indicates chassis is below the temperature threshold. stateOverTemp Indicates chassis is above the temperature threshold.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	stateOk(1), stateOverTemp(2)

tmnxChassisFanTable		1.3.6.1.4.1.6527.3.1.2.2.1.4
This table contains information about fan trays.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxChassisFanEntry

tmnxChassisFanEntry		1.3.6.1.4.1.6527.3.1.2.2.1.4.1
Contains information regarding a fan tray.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxChassisFanEntry

tmnxChassisFanIndex		1.3.6.1.4.1.6527.3.1.2.2.1.4.1.1
The unique value which identifies a specific fan tray in the chassis.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..31

tmnxChassisFanOperStatus		1.3.6.1.4.1.6527.3.1.2.2.1.4.1.2
Current status of the Fan tray.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisFanSpeed		1.3.6.1.4.1.6527.3.1.2.2.1.4.1.3
The value of tmnxChassisFanSpeed indicates if the fans in this fan tray are running at 'halfSpeed' or 'fullSpeed'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), halfSpeed(2), fullSpeed(3)

tmnxChassisPowerSupplyTable		1.3.6.1.4.1.6527.3.1.2.2.1.5
This table contains information about power supply trays.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxChassisPowerSupplyEntry

tmnxChassisPowerSupplyEntry		1.3.6.1.4.1.6527.3.1.2.2.1.5.1
Contains information regarding a power supply tray.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxChassisPowerSupplyEntry

tmnxChassisPowerSupplyId		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.1
The unique identifier index for a power supply tray in the chassis.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..31

tmnxChassisPowerSupplyACStatus		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.2
If the value of tmnxChassisPowerSupplyACStatus is 'deviceStateOk', the input AC voltage is within range. If the value is 'deviceStateFailed', an AC voltage out of range condition has been detected. A value of 'deviceNotEquipped' indicates that the AC power supply is not present.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisPowerSupplyDCStatus		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.3
If the value of tmnxChassisPowerSupplyDCStatus is 'deviceStateOk', the input DC voltage is within range. If the value is 'deviceStateFailed', an DC voltage out of range condition has been detected. A value of 'deviceNotEquipped' indicates that the DC power supply is not present.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisPowerSupplyTempStatus		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.4
If the value of tmnxChassisPowerSupplyTempStatus is 'deviceStateOk', the current temperature is within acceptable range. If the value is 'deviceStateFailed', a temperature too high condition has been detected.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisPowerSupplyTempThreshold		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.5
The temperature threshold for this power supply tray in degrees celsius. When the temperature raises above tmnxChassisPowerSupplyTempThreshold, a 'temperature too high' event will be generated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tmnxChassisPowerSupply1Status		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.6
The overall status of an equipped power supply. For AC multiple power supplies, this represents the overall status of the first power supply in the tray (or shelf). For any other type, this represents the overall status of the power supply. If tmnxChassisPowerSupply1Status is 'deviceStateOk', then all monitored statuses are 'deviceStateOk'. A value of 'deviceStateFailed' represents a condition where at least one monitored status is in a failed state.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisPowerSupply2Status		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.7
The overall status of an equipped power supply. For AC multiple power supplies, this represents the overall status of the second power supply in the tray (or shelf). For any other type, this field is unused and set to 'deviceNotEquipped'. If tmnxChassisPowerSupply2Status is 'deviceStateOk', then all monitored statuses are 'deviceStateOk'. A value of 'deviceStateFailed' represents a condition where at least one monitored status is in a failed state.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisPowerSupplyAssignedType		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.8
tmnxChassisPowerSupplyAssignedType configures the type of power supply for a platform. Based on the value assigned to this object, various power supply monitoring signals will be interpreted. For example, if a platform is provisioned to use DC power supplies, then the signal that indicates an AC power supply is missing can be ignored. This is required for proper generation of traps and LED management.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), dc(1), acSingle(2), acMultiple(3)

tmnxChassisPowerSupplyInputStatus		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.9
If the value of tmnxChassisPowerSupplyInputStatus is 'deviceStateOk', the input voltage of the power supply is within range. If the value is 'deviceStateFailed', an input voltage out of range condition has been detected. A value of 'deviceNotEquipped' indicates that the power supply is not present.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisPowerSupplyOutputStatus		1.3.6.1.4.1.6527.3.1.2.2.1.5.1.10
If the value of tmnxChassisPowerSupplyOutputStatus is 'deviceStateOk', the output voltage of the power supply is within range. If the value is 'deviceStateFailed', an output voltage out of range condition has been detected. A value of 'deviceNotEquipped' indicates that the power supply is not present.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxChassisTypeTable		1.3.6.1.4.1.6527.3.1.2.2.1.6
The chassis type table has an entry for each Alcatel 7x50 SR series chassis model.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxChassisTypeEntry

tmnxChassisTypeEntry		1.3.6.1.4.1.6527.3.1.2.2.1.6.1
Each row entry represents an Alcatel 7x50 SR series Chassis model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxChassisTypeEntry

tmnxChassisTypeIndex		1.3.6.1.4.1.6527.3.1.2.2.1.6.1.1
The unique index value which identifies this type of Alcatel 7x50 SR series chassis model.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxChassisType

tmnxChassisTypeName		1.3.6.1.4.1.6527.3.1.2.2.1.6.1.2
The administrative name that identifies this type of Alcatel 7x50 SR series chassis model. This name string may be used in CLI commands to specify a particular chassis model type.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxChassisTypeDescription		1.3.6.1.4.1.6527.3.1.2.2.1.6.1.3
A detailed description of this Alcatel 7x50 SR series chassis model.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxChassisTypeStatus		1.3.6.1.4.1.6527.3.1.2.2.1.6.1.4
When tmnxChassisTypeStatus has a value of 'true' it indicates that this chassis model is supported in this revision of the management software. When it has a value of 'false' there is no support.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxHwLastChange		1.3.6.1.4.1.6527.3.1.2.2.1.7
The value of sysUpTime when the tmnxHwTable was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxHwTable		1.3.6.1.4.1.6527.3.1.2.2.1.8
The tmnxHwTable has an entry for each managed hardware component in the Alcatel 7x50 SR series system's chassis. Examples of these hardware component types are IOM, Fabric, and CPM cards, MCM and CCM, and MDA modules. Similar information for physical ports is in the tmnxPortObjs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxHwEntry

tmnxHwEntry		1.3.6.1.4.1.6527.3.1.2.2.1.8.1
Each row entry represents an Alcatel 7x50 SR series manufactured hardware component. Entries cannot be created and deleted via SNMP SET operations. When an entry is created in one of the card tables, IOM, CPM, Fabric or MDA, a tmnxHwEntry is created for the common hardware management information for that card in that chassis. When the card is removed from the chassis, its corresponding tmnxHwEntry is deleted. The tmnxHwIndex is bitmapped: | 32 25 | 24 17 | 16 9 | 8 1 | +-------------+-------------+-------------+-------------+ | TmnxHwClass | 00000000 | Slot | number | +-------------+-------------+-------------+-------------+ The Slot field is only used for components on cards in slots. It is zero for all others. The number field starts from 1 and indicates which component. E.g. Power supply 1 or 2.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxHwEntry

tmnxHwIndex		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.1
The value of tmnxHwIndex is a unique index that identifies common management information for Alcatel 7x50 SR series manufactured hardware components within the specified chassis.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxHwIndex

tmnxHwID		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.2
The value of tmnxHwID is an object identifier that points to the table and row entry with additional management information specific to this hardware component's class.
Status: current	Access: read-only
OBJECT-TYPE
	RowPointer

tmnxHwMfgString		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.3
The tmnxHwMfgString contains unspecified Alcatel 7x50 SR series manufacturing information and includes the Alcatel vendor information.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..253)

tmnxHwMfgBoardNumber		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.4
The tmnxHwMfgBoardNumber contains the part number information.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

tmnxHwSerialNumber		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.5
The unique Alcatel 7x50 SR series serial number of the hardware component.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

tmnxHwManufactureDate		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.6
The manufacturing date of the hardware component in 'mmddyyyy' ascii format.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(8)

tmnxHwClass		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.7
The value of tmnxHwClass indicates the general hardware type of this component. If no appropriate enumeration exists for this hardware component then the value 'other (1)' is used. If the agent cannot identify this hardware component then the value 'unknown (2)' is used.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwClass

tmnxHwName		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.8
The value of tmnxHwName is the name of the component as assigned by the system software itself and is suitable for use in CLI commands. This may be a text name such as 'console' or a port ID such as '2/2'. If there is no predefined name then a zero length string is returned. Note that the value of tmnxHwName for two component entries will be the same if the CLI does not distinguish between them, e.g. the chassis slot-1 and the card in slot-1.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxHwAlias		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.9
The value of tmnxHwAlias is the administrative name assigned to this hardware component by the CLI user or network manager. It is saved across re-initializations and reboots of the system.
Status: current	Access: read-write
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxHwAssetID		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.10
The value of tmnxHwAssetID is an administratively assigned asset tracking identifier for this hardware component. It is saved across re-initializations and reboots of the system. If no asset tracking information is associated with this hardware component, a zero-length string is returned to an SNMP get request. Some hardware components do not have asset tracking identifiers. Components for which tmnxHwIsFRU has a value of 'false' do not need their own unique asset tracking identifier. In this case, the agent denies write access to this object and returns a zero-length string to an SNMP get request.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

tmnxHwCLEI		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.11
The Common Language Equipment Identifier, CLEI, code is a unique 10-character identifier, that is fixed by the manufacturer. It consists of ten alphanumeric characters. The first seven characters present a concise summary of an equipment entity's circuit or transport capabilities, e.g., functional, electrical, bandwidth, etc. CLEI codes for plug-in or portable equipment with the same first seven characters (CLEI-7) are considered bidirectionally interchangeable and group under a G level record. Most licensees plug-in inventories and records are controlled at the group level. The eighth character denotes the reference source used for coding the item, and the last two characters denote manufacturing vintage or version, and other complemental information. A ten-character CLEI code that is developed for a specific piece of equipment is unique within the CLEI code universe and is used in A level records; the code is not assigned to any other equipment piece. Equipment is coded to a first or major application. When the same equipment is usable in another application or system, it is not recorded nor are additional codes developed for that purpose.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(10)

tmnxHwIsFRU		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.12
The value of tmnxHwIsFRU indicates whether or not this hardware component is a Field Replaceable Unit (FRU) or not. Those components that are permanently contained within a FRU have a value of 'false'.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxHwContainedIn		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.13
The value of tmnxHwContainedIn is the tmnxHwIndex value for the row entry of the hardware component that contains this component. A value of zero indicates that this component is not contained in any other component.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

tmnxHwParentRelPos		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.14
The value of tmnxHwParentRelPos indicates the relative position of this hardware component among all its 'sibling' components. A sibling component shares the same instance values for tmnxHwContainedIn and tmnxHwClass objects. If the associated value of tmnxHwContainedIn is zero, then the value -1 is returned.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-1..2147483647

tmnxHwAdminState		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.15
The desired administrative status of this hardware component. Write access will be denied for those components that do not have administrative status. An attempt to set tmnxHwAdminState to 'operateSwitch (5)' will fail if the hardware component is not part of a redundant pair. Some examples of redundant hardware are the CPM cards and fabric cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), inService(2), outOfService(3), diagnose(4), operateSwitch(5)

tmnxHwOperState		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.16
The actual operational status of this hardware component. unknown (1) Status cannot be determined inService (2) Online - If tmnxHwClass has a value of 'ioModule (8)' or 'cpmModule (9), the card is present, booted, configured, and running. outOfService (3) Ready - The hardware component is OK but is down because tmnxHwAdminState has a value of 'outOfService (3)'. diagnosing (4) Not implemented. failed (5) This hardware component has failed. The value of tmnxHwFailureReason indicates the type of failure. If tmnxHwClass has a value of 'ioModule(8)' or 'cpmModule(9)', there is a card in the slot but it has failed. booting (6) A card is in the transitional startup state. empty (7) There is no card in the slot and it has not been pre-configured. provisioned (8) There is no card in the slot but it has been pre-configured. unprovisioned (9) There is a card in the slot but it is not configured. upgrade (10) Card software version is compatible with and newer than that running on the current active CPM. downgrade (11) Card software version is compatible with and older than that running on the current active CPM. inServiceUpgrade (12) Card is inService and the card software version is compatible with and newer than that running on the current active CPM. This state applies only to a standby CPM card. This enumeration is no longer supported as of release 5.0. inServiceDowngrade (13) Card is inService and the card software is compatible with and older than that running on the current active CPM. This state applies only to a standby CPM card. This enumeration is no longer supported as of release 5.0. resetPending (14) Card is awaiting reset following an upgrade or downgrade activity switch. The card software version is upgrade or downgrade compatible but will be reset in order to update it to match the active CPM software. The value of tmnxChassisUpdateWaitTime indicates the how long the system will wait following an upgrade or downgrade activity switch before it resets IOM cards. This state applies only to IOM cards. This enumeration is no longer supported as of release 5.0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), inService(2), outOfService(3), diagnosing(4), failed(5), booting(6), empty(7), provisioned(8), unprovisioned(9), upgrade(10), downgrade(11), inServiceUpgrade(12), inServiceDowngrade(13), resetPending(14)

tmnxHwTempSensor		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.17
The value of tmnxHwTempSensor indicates whether or not this hardware component contains a temperature sensor.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxHwTemperature		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.18
The current temperature reading in degrees celsius from this hardware component's temperature sensor. If this component does not contain a temperature sensor, then the value -1 is returned.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tmnxHwTempThreshold		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.19
The temperature threshold for this hardware component in degrees celsius. When the value of tmnxHwTemperature raises above tmnxHwTempThreshold, a 'temperature too high' event will be generated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tmnxHwBootCodeVersion		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.20
The version number of boot eprom on the card in this slot. If no specific software program is associated with this hardware component then this object will contain a zero length string.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxHwSoftwareCodeVersion		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.21
The software product release version number for the software image currently running on this IOM or CPM card. If no specific software program is associated with this hardware component then this object will contain a zero length string.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxHwSwLastBoot		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.22
The date and time the software running on this IOM or CPM card was last rebooted. If this row entry represents a standby CPM card, the date and time indicated is when the standby completed its initial synchronization process and became ready to take over in case the active card fails or a manual switchover command is issued.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

tmnxHwSwState		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.23
The state of the software running on this IOM or CPM card. The tmnxHwSwState object is obsolete. The Alcatel 7x50 platform cannot distinguish software status separate from the hardware status. Instead of using this object, additional operational states have been added to tmnxHwOperState. If no specific software program is associated with this hardware component then this object will contain a zero.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), hwFailure(1), swFailure(2), hwInitting(3), swDownloading(4), swInitting(5), swInitted(6), swRunning(7)

tmnxHwAlarmState		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.24
The value of tmnxHwAlarmState indicates the current alarm state for this hardware component.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxAlarmState

tmnxHwLastAlarmEvent		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.25
The value of tmnxHwLastAlarmEvent is an object identifier whose object name and instance values point to the row entry in the ALARM-MIB that contains the most recent alarm event associated with this hardware component. If the tmnxHwAlarmState has a value of 'alarmCleared', the most recent alarm event will be in the nlmAlarmClearedTable. If it has a value of 'alarmActive', the entry pointed to is in the nlmAlarmActiveTable. If the value of tmnxHwLastAlarmEvent is '0.0', then either there have not been any alarm events associated with this chassis since the system was last booted, or the last alarm event has aged out and its entry is no longer available in the ALARM-MIB tables.
Status: current	Access: read-only
OBJECT-TYPE
	RowPointer

tmnxHwClearAlarms		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.26
Setting this action variable causes all the active alarms associated with this hardware component to be moved from the ALARM-MIB nlmActiveAlarmTable to the nlmClearedAlarmTable. This action button is primarily meant for use as a code development aid. This object may be removed from the ALCATEL-IND1-TIMETRA-CHASSIS-MIB before product release.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxHwSwImageSource		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.27
The value of tmnxHwSwImageSource indicates the location in the Boot Options File (BOF) where the software image file was found when the system last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), primary(1), secondary(2), tertiary(3)

tmnxHwMfgDeviations		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.28
tmnxHwMfgDeviations contains a record of changes done by the manufacturing to the hardware or software and which is outside the normal revision control process.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

tmnxHwBaseMacAddress		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.29
tmnxHwBaseMacAddress contains the base MAC address of the hardware component. It is applicable only if tmnxHwClass is of type 'chassis', 'ioModule', 'cpmModule' or 'mdaModule'.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

tmnxHwFailureReason		1.3.6.1.4.1.6527.3.1.2.2.1.8.1.30
tmnxHwFailureReason indicates the reason why a hardware component 'failed' as indicated in tmnxHwOperState.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxHwContainsTable		1.3.6.1.4.1.6527.3.1.2.2.1.9
The tmnxHwContainsTable shows the container/containee relationship between entries in the tmnxHwTable. The hardware component containment tree can be constructed from information in the tmnxHwTable, but this table provides the information in a more convenient format for the manager system to use.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxHwContainsEntry

tmnxHwContainsEntry		1.3.6.1.4.1.6527.3.1.2.2.1.9.1
Each row entry represents a single container/containee relationship. Entries cannot be created and deleted via SNMP SET operations.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxHwContainsEntry

tmnxHwContainedIndex		1.3.6.1.4.1.6527.3.1.2.2.1.9.1.1
The value of tmnxHwIndex for the contained hardware component.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxCcmTable		1.3.6.1.4.1.6527.3.1.2.2.1.10
This table contains information about CCM.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCcmEntry

tmnxCcmEntry		1.3.6.1.4.1.6527.3.1.2.2.1.10.1
Contains information regarding a CCM.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcmEntry

tmnxCcmIndex		1.3.6.1.4.1.6527.3.1.2.2.1.10.1.1
The unique value which identifies a specific CCM instance in the chassis.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..8

tmnxCcmOperStatus		1.3.6.1.4.1.6527.3.1.2.2.1.10.1.2
Current status of the CCM.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxCcmHwIndex		1.3.6.1.4.1.6527.3.1.2.2.1.10.1.3
The value of tmnxCcmHwIndex is the index into the tmnxHwTable for the row entry that represents the hardware component information for this CCM.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxCcmEquippedType		1.3.6.1.4.1.6527.3.1.2.2.1.10.1.4
A bit-mask that identifies the CCM type that is physically inserted into this chassis. There will not be more than one bit set at a time in tmnxCcmEquippedType.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCcmType

tmnxCcmTypeTable		1.3.6.1.4.1.6527.3.1.2.2.1.11
The card type table has an entry for each Alcatel 7710 series Chassis Control Module (CCM) model.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCcmTypeEntry

tmnxCcmTypeEntry		1.3.6.1.4.1.6527.3.1.2.2.1.11.1
Each row entry represents an Alcatel 7710 series CCM model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcmTypeEntry

tmnxCcmTypeIndex		1.3.6.1.4.1.6527.3.1.2.2.1.11.1.1
The unique index value which identifies this type of Alcatel 7710 series CCM model.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcmType

tmnxCcmTypeName		1.3.6.1.4.1.6527.3.1.2.2.1.11.1.2
The administrative name that identifies this type of Alcatel 7710 series CCM model. This name string may be used in CLI commands to specify a particular card model type.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxCcmTypeDescription		1.3.6.1.4.1.6527.3.1.2.2.1.11.1.3
A detailed description of this Alcatel 7710 series CCM model.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCcmTypeStatus		1.3.6.1.4.1.6527.3.1.2.2.1.11.1.4
When tmnxCcmTypeStatus has a value of 'true' it indicates that this CCM is supported in this revision of the management software. When it has a value of 'false' there is no support.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxCardLastChange		1.3.6.1.4.1.6527.3.1.2.2.3.1
The value of sysUpTime when the tmnxCardTable was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxCardTable		1.3.6.1.4.1.6527.3.1.2.2.3.2
The tmnxCardTable has an entry for each IOM card slot in each chassis in the TMNX system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCardEntry

tmnxCardEntry		1.3.6.1.4.1.6527.3.1.2.2.3.2.1
Each row entry represents an IOM card slot in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxChassisEntry is created, a tmnxCardEntry is created for each IOM card slot in that chassis. Before a tmnxChassisEntry can be deleted, each tmnxCardEntry for that chassis must be in the proper state for removal.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCardEntry

tmnxCardSlotNum		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.1
The unique value which identifies this IOM slot within a chassis in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSlotNum

tmnxCardSupportedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.2
A bit-mask that specifies what card types can be physically supported in this IOM slot in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCardType

tmnxCardAllowedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.3
A bit-mask that specifies what IOM card types the administrator has designated be allowed to be inserted into this slot. If the slot has not-been pre-provisioned and a card that does not match one of the allowed types is inserted into this slot, a mis-match alarm will be raised. If a specific value has not yet been SET by the manager, tmnxCardAllowedTypes will return the same value to a GET request as tmnxCardSupportedTypes. The object was made obsolete in the 3.0 release.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TmnxCardType

tmnxCardAssignedType		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.4
A bit-mask that identifies the administratively assigned (pre-provisioned) IOM card type that should occupy this slot in this chassis. If tmnxCardAssignedType has a value of 'unassigned', this slot has not yet been pre-provisioned. There must not be more than one bit set at a time in tmnxCardAssignedType.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxCardType

tmnxCardEquippedType		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.5
A bit-mask that identifies the IOM card type that is physically inserted into this slot in this chassis. If the slot has been pre-provisioned, tmnxCardAssignedType is not equal 'unassigned', and the value of tmnxCardEquippedType is not the same as tmnxCardAssignedType, a mis-match alarm will be raised. If the slot has not been pre-provisioned, and the value of tmnxCardEquippedType is not one of the allowed types as specified by tmnxCardAllowedTypes, a mis-match alarm will be raised. There will not be more than one bit set at a time in tmnxCardEquippedType. A value of 0 indicates the IOM card type is not recognized by the software.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCardType

tmnxCardHwIndex		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.6
The value of tmnxCardHwIndex is the index into the tmnxHwTable for the row entry that represents the hardware component information for this IOM card.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxCardClockSource		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.10
The clock source used by the IOM card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCardNumMdaSlots		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.11
The number of Media Dependent Adapter (MDA) slots available on this IOM card.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCardNumMdas		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.12
The number of Media Dependent Adapters installed on this IOM card.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCardReboot		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.13
Setting this variable to 'doAction' causes the IOM card to execute a soft-reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxCardMemorySize		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.14
The value of tmnxCardMemorySize indicates the amount of memory, in mega-bytes, populated on this IOM card.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCardNamedPoolAdminMode		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.15
The value of tmnxCardNamedPoolAdminMode specifies whether or not an IOM is provisioned for the configuration of named pools. If the value of tmnxCardNamedPoolAdminMode is 'inService(2)', the system will change the way default pools are created and allow for the creation of MDA and port level named buffer pools. If the value of tmnxCardNamedPoolAdminMode is 'outOfService(3)', the system will not create per port pools, instead a default network and access pool is created for ingress and egress and is shared by queues on all ports. This object is used in conjunction with tmnxCardNamedPoolOperMode.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAdminState

tmnxCardNamedPoolOperMode		1.3.6.1.4.1.6527.3.1.2.2.3.2.1.16
The value of tmnxCardNamedPoolOperMode specifies whether or not an IOM provisioned with tmnxCardNamedPoolAdminMode to a value of 'inService(2)' will activly use named pools or not. A value of 'outOfService(3) means that the named pool configurations will not be downloaded to the IOM until after a reset of the IOM is performed. A value of 'inService(2)' means that the named pool configurations are programmed by the IOM. On systems using a separate CPM and IOM combination the value of tmnxCardNamedPoolOperMode and tmnxCardNamedPoolAdminMode will always be in sync due to a mandatory reboot of the IOM. On systems using a combined image (CFM) these values will be out-of-sync until the chassis is rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxAdminState

tmnxCpmCardLastChange		1.3.6.1.4.1.6527.3.1.2.2.3.3
The value of sysUpTime when the tmnxCpmCardTable was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxCpmCardTable		1.3.6.1.4.1.6527.3.1.2.2.3.4
The tmnxCpmCardTable has an entry for each CPM card or module in each chassis in the TMNX system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCpmCardEntry

tmnxCpmCardEntry		1.3.6.1.4.1.6527.3.1.2.2.3.4.1
Each row entry represents a CPM card or module in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxChassisEntry is created, a tmnxCpmCardEntry is created for each CPM card or module in that chassis. Before a tmnxChassisEntry can be deleted, each tmnxCpmCardEntry for that chassis must be in the proper state for removal.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCpmCardEntry

tmnxCpmCardSlotNum		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.1
The unique value which identifies this slot within a chassis in the system. Depending upon the value of tmnxChassisType, this may represent a fabric slot or a regular card slot. If this CPM module resides on a fabric card, tmnxCpmCardSlotNum has the value the corresponding tmnxFabricSlotNum. If this is a CPM module on a fabric card, tmnxCpmCardSlotNum is the fabric slot number in the chassis where this CPM module is located. Else if this is a CPM card, tmnxCpmCardSlotNum is a regular card slot number.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSlotNum

tmnxCpmCardNum		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.2
The unique value which identifies this CPM module within a specific card slot within a chassis in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

tmnxCpmCardSupportedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.3
A bit-mask that specifies what CPM card types can be physically supported in this slot in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCardType

tmnxCpmCardAllowedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.4
A bit-mask that specifies what CPM card types the administrator has designated be allowed to be inserted into this slot. If the slot has not-been pre-provisioned and a card that does not match one of the allowed types is inserted into this slot, a mis-match alarm will be raised. If a specific value has not yet been SET by the manager, tmnxCpmCardAllowedTypes will return the same value to a GET request as tmnxCpmCardSupportedTypes. The object was made obsolete in the 3.0 release.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TmnxCardType

tmnxCpmCardAssignedType		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.5
A bit-mask that identifies the administratively assigned (pre-provisioned) CPM card type that should occupy this slot in this chassis. If tmnxCpmCardAssignedType has a value of 'unassigned', this slot has not yet been pre-provisioned. There must not be more than one bit set at a time in tmnxCpmCardAssignedType.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxCardType

tmnxCpmCardEquippedType		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.6
A bit-mask that identifies the CPM card type that is physically inserted into this slot in this chassis. If the slot has been pre-provisioned, tmnxCpmCardAssignedType is not equal 'unassigned', and the value of tmnxCpmCardEquippedType is not the same as tmnxCpmCardAssignedType, a mis-match alarm will be raised. If the slot has not been pre-provisioned, and the value of tmnxCpmCardEquippedType is not one of the allowed types as specified by tmnxCpmCardAllowedTypes, a mis-match alarm will be raised. There will not be more than one bit set at a time in tmnxCpmCardEquippedType.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCardType

tmnxCpmCardHwIndex		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.7
The value of tmnxCpmCardHwIndex is the index into the tmnxHwTable for the row entry that represents the hardware component information for this CPM card or module.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxCpmCardBootOptionVersion		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.8
The version number of boot option file (BOF) read by the CPM card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmCardBootOptionLastModified		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.9
The date and time the boot options file (BOF) for this card was last modified. If tmnxCpmCardBootOptionLastModified is more recent than tmnxHwSwLastBoot, the boot options file has been edited since the software was booted and different software images or configuration will likely be used when this card is next rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

tmnxCpmCardConfigBootedVersion		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.10
The version of the configuration file read when this CPM card was last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmCardIndexBootedVersion		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.11
The version of the index file read when this CPM card was last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmCardConfigLastModified		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.12
The date and time the running configuration was last modified. If tmnxCpmCardConfigLastModified is more recent than tmnxHwSwLastBoot, the current configuration may be different than that in the configuration file read upon system initialization.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

tmnxCpmCardConfigLastSaved		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.13
The date and time the current configuration was last saved. If tmnxCpmCardConfigLastSaved is more recent the value of tmnxHwSwLastBoot, the initial configuration is likely to be different the next time the system is rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

tmnxCpmCardRedundant		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.14
This variable indicates if the CPM card is standalone or part of a pair of redundant cards. If 'redundantDisabled', tmnxHwOperState indicates the specific reason why this redundant CPM card is not available. Note that the 'redudantSplit' option is not implemented.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	singleton(1), redundantActive(2), redundantStandby(3), redundantSplit(4), redundantDisabled(5), redundantSynching(6)

tmnxCpmCardClockSource		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.15
The clock source used by the CPM card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmCardNumCpus		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.16
The value of tmnxCpmCardNumCpus indicates the number of CPU chips populated on this CPM module.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCpmCardCpuType		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.17
The value of tmnxCpmCardCpuType indicates the type of CPU chips populated on this CPM module.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), mips(2), pentium-pc(3)

tmnxCpmCardMemorySize		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.18
The value of tmnxCpmCardMemorySize indicates the amount of memory, in mega-bytes, populated on this CPM module.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCpmCardSwitchToRedundantCard		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.19
Setting this variable to doAction causes the switchover to the redundant CPM card.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxCpmCardReboot		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.20
Setting this variable to 'doAction' causes the CPM card to execute a soft-reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxCpmCardRereadBootOptions		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.21
Setting this variable to 'doAction' causes the Boot Options File (BOF) to be reread and applied.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxCpmCardConfigFileLastBooted		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.22
tmnxCpmCardConfigFileLastBooted indicates the location and name of the configuration file from which the system last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxCpmCardConfigFileLastSaved		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.23
tmnxCpmCardConfigFileLastSaved indicates the location and name of the file to which the configuration was last saved.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxCpmCardConfigFileLastBootedHeader		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.24
tmnxCpmCardConfigFileLastBootedHeader contains the header of the configuration file from which the system last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..512)

tmnxCpmCardIndexFileLastBootedHeader		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.25
tmnxCpmCardIndexFileLastBootedHeader contains the header of the index file from which the system last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..512)

tmnxCpmCardBootOptionSource		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.26
tmnxCpmCardBootOptionSource indicates the compact flash slot where the Boot Options File (BOF) file was found when the system last rebooted. For example, if the BOF file was found on compact flash slot 1, the value of this variable will be 'cf1:'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxCpmCardConfigSource		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.27
The value of tmnxCpmCardConfigSource indicates the location in the Boot Options File(BOF) where the configuration file was found when the system last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), primary(1), secondary(2), tertiary(3)

tmnxCpmCardBootOptionLastSaved		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.28
The date and time the boot options file (BOF) was last saved. If tmnxCpmCardBootOptionLastSaved is more recent than the value of tmnxHwSwLastBoot, the boot options file has been edited since the software was booted and different software images or configuration will likely be used when this card is next rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

tmnxCpmCardMasterSlaveRefState		1.3.6.1.4.1.6527.3.1.2.2.3.4.1.30
The current Master/Slave clocking reference designation. primaryRef Indicates this card is designated as the primary clocking reference in a redundant system. secondaryRef Indicates this card is designated as the secondary clocking reference in a redundant system. notInitialized Indicates the clock is not initialized.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primaryRef(1), secondaryRef(2), notInitialized(3)

tmnxFabricLastChange		1.3.6.1.4.1.6527.3.1.2.2.3.5
The value of sysUpTime when the tmnxFabricTable was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxFabricTable		1.3.6.1.4.1.6527.3.1.2.2.3.6
The tmnxFabricTable has an entry for each fabric card slot in each chassis in the TMNX system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxFabricEntry

tmnxFabricEntry		1.3.6.1.4.1.6527.3.1.2.2.3.6.1
Each row entry represents a fabric card slot in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxChassisEntry is created, a tmnxFabricEntry is created for each fabric card slot in that chassis. Before a tmnxChassisEntry can be deleted, each tmnxFabricEntry for that chassis must be in the proper state for removal.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxFabricEntry

tmnxFabricSlotNum		1.3.6.1.4.1.6527.3.1.2.2.3.6.1.1
The unique value which identifies this fabric slot within a chassis in the system. The CPM cards and IOM cards cannot be physically inserted into the switch fabric card slots. In some models, the CPM is not a separate card, but rather a module on a Fabric card.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..16

tmnxFabricAssignedType		1.3.6.1.4.1.6527.3.1.2.2.3.6.1.2
The administratively assigned switch fabric card type that should occupy this fabric slot in this chassis.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxCardType

tmnxFabricEquippedType		1.3.6.1.4.1.6527.3.1.2.2.3.6.1.3
The switch fabric card type that is physically inserted into this slot in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCardType

tmnxFabricHwIndex		1.3.6.1.4.1.6527.3.1.2.2.3.6.1.4
The value of tmnxHwIndex is the index into the tmnxHwTable to locate the row entry that represents the hardware component information for this fabric card.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxCpmFlashTable		1.3.6.1.4.1.6527.3.1.2.2.3.7
This table contains information about Flash devices on a CPM card.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCpmFlashEntry

tmnxCpmFlashEntry		1.3.6.1.4.1.6527.3.1.2.2.3.7.1
Contains information regarding a CPM card's flash unit.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCpmFlashEntry

tmnxCpmFlashId		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.1
The unique identifier index for a flash device on a CPM card.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..32

tmnxCpmFlashOperStatus		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.2
Current status of this flash unit on this CPM card.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxDeviceState

tmnxCpmFlashSerialNumber		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.3
The serial number for this flash unit on this CPM card.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmFlashFirmwareRevision		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.4
The firmware revision number for this flash unit on this CPM card.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmFlashModelNumber		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.5
The model number for this flash unit on this CPM card.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCpmFlashCapacity		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.6
The value of tmnxCpmFlashCapacity indicates the maximum size of this flash unit in 512-byte sectors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCpmFlashUsed		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.7
The value of tmnxCpmFlashUsed indicates the amount used, in 512-byte sectors, of this flash unit's total capacity.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxCpmFlashHwIndex		1.3.6.1.4.1.6527.3.1.2.2.3.7.1.8
The value of tmnxHwIndex is the index into the tmnxHwTable for the row entry that represents the hardware component information for this flash unit.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxMDATable		1.3.6.1.4.1.6527.3.1.2.2.3.8
The tmnxMDATable has an entry for each MDA slot in each IOM card in this chassis in the TMNX system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxMDAEntry

tmnxMDAEntry		1.3.6.1.4.1.6527.3.1.2.2.3.8.1
Each row entry represents a MDA slot in an IOM card in a chassis in the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxCardEntry has tmnxCardAssignedType or tmnxCardEquippedType equal to an IOM card type that supports MDA slots, a tmnxMDAEntry is created by the agent for each MDA slot on that IOM card. Before a tmnxCardEntry can be deleted, each tmnxMDAEntry for that card must be in the proper state for removal.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxMDAEntry

tmnxMDASlotNum		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.1
The unique value which identifies this MDA slot within a specific IOM card in the system. Rows with a tmnxMDASlotNum value of zero (0) represent the special case of an IOM card without MDA slots but that instead has its ports directly on the IOM card itself. In that case, there should be only that one row entry in the tmnxMDATable for that IOM card.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..16

tmnxMDASupportedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.2
A bit-mask that specifies what MDA card types can be physically supported in this slot in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxMDASuppType

tmnxMDAAllowedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.3
An integer that specified what MDA card types the administrator has designated be allowed to be inserted into this slot. If the slot has not-been pre-provisioned and a MDA card that does not match one of the allowed types is inserted into this slot, a mis-match alarm will be raised. The object was made obsolete in the 3.0 release.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TmnxMdaType

tmnxMDAAssignedType		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.4
An integer that indicates the administratively assigned (pre-provisioned) MDA card type that should occupy this slot in this chassis. If tmnxMDAAssignedType has a value of 'unassigned', this slot has not yet been pre-provisioned.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxMdaType

tmnxMDAEquippedType		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.5
An integer that indicates the MDA card type that is physically inserted into this slot in this chassis. If the slot has been pre-provisioned, tmnxMDAAssignedType is not equal 'unassigned', and the value of tmnxMDAEquippedType is not the same as tmnxMDAAssignedType, a mis-match alarm will be raised. A value of 0 indicates the equipped MDA is not supported by this software release.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxMdaType

tmnxMDAHwIndex		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.6
The value of tmnxHwIndex is the index into the tmnxHwTable for the row entry that represents the hardware component information for this MDA card.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxMDAMaxPorts		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.7
The maximum number of ports that can be equipped on this MDA card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..127

tmnxMDAEquippedPorts		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.8
The value of tmnxMDAEquippedPorts indicates the number of ports equipped on this MDA card.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxMDATxTimingSelected		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.10
The transmit timing method which is presently selected and being used by this MDA. tmnxMDATxTimingSelected will be set to 'not-applicable' if this MDA does not use the transmit timing subsystem.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cpm-card-A(1), cpm-card-B(2), local(3), holdover(4), not-applicable(5)

tmnxMDASyncIfTimingStatus		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.11
Indicates the status of the synchronous equipment timing subsystem. If the tmnxSyncIfTimingRef1Qualified and tmnxSyncIfTimingRef2Qualified are both set to 'not-qualified, then tmnxMDASyncIfTimingStatus is set to 'not-qualified'. If any of the timing references is in use, then tmnxMDASyncIfTimingStatus is set to 'qualified'. tmnxMDASyncIfTimingStatus will be set to 'not-applicable' if this MDA does not use the transmit timing subsystem.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	qualified(1), not-qualified(2), not-applicable(3)

tmnxMDANetworkIngQueues		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.12
Specifies the network queue policy being used for this object to define the queueing structure for this object.
Status: current	Access: read-write
OBJECT-TYPE
	TNamedItem

tmnxMDACapabilities		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.13
tmnxMDACapabilities indicates the capabilities of this MDA. It identifies the type of MDA and the protocols that can run on it.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	isEthernet(0), isSonet(1), isTDM(2), supportsPPP(3), supportsFR(4), supportsATM(5), supportscHDLC(6), isCMA(7), supportsCEM(8)

tmnxMDAMinChannelization		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.14
tmnxMDAMinChannelization indicates the minimum size of the channel that can exist on this MDA.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxMDAChanType

tmnxMDAMaxChannelization		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.15
tmnxMDAMaxChannelization indicates the maximum size of the channel that can exist on this MDA.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxMDAChanType

tmnxMDAMaxChannels		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.16
tmnxMDAMaxChannels is applicable for SONET and TDM MDAs only. It indicates the total number of leaf SONET paths, TDM channels and bundles on the MDA that may be configured to pass traffic.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxMDAChannelsInUse		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.17
tmnxMDAChannelsInUse is applicable for SONET and TDM MDAs only. It indicates the total number of leaf SONET paths, TDM channels and bundles on the MDA which are in use. A leaf SONET path or TDM channel which is currently capable of passing traffic is considered to be in use. Also, a SONET path or TDM channel which is channelized and has no subchannels capable of passing traffic is considered to be in use. A SONET path or TDM channel which is channelized and has one or more subchannels capable of passing traffic is not considered to be in use, although the subchannels themselves are considered to be in use. A bundle is considered to be a channel in use as are each of its members since they are TDM channels capable of passing traffic.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxMDACcagId		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.18
When tmnxMDAAssignedType has a value of 'cca' , the value of tmnxMDACcagId specifies the Cross Connect Aggregation Group (CCAG) entry this MDA is provisioned on. If this entry does not represent a 'cca' MDA or is not associated with a CCAG, tmnxMDACcagId has a value of zero.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxCcagId

tmnxMDAReboot		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.19
Setting this variable to 'doAction' causes the MDA to execute a soft-reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxMDAHiBwMcastSource		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.20
The value of tmnxMDAHiBwMcastSource specifies if this MDA should attempt to allocate separate fabric planes to allocate high bandwidth multicast traffic taps. tmnxMDAHiBwMcastGroup must be set in the same SNMP request PDU with tmnxMDAHiBwMcastSource or an 'inconsistentValue' error will be returned.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

tmnxMDAHiBwMcastAlarm		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.21
The value of tmnxMDAHiBwMcastAlarm specifies if a tmnxChassisHiBwMcastAlarm alarm is raised if there are more than one high bandwidth multicast traffic taps sharing a plane.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

tmnxMDAHiBwMcastTapCount		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.22
The value of tmnxMDAHiBwMcastTapCount indicates the number of high bandwidth multicast traffic taps on this MDA.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

tmnxMDAHiBwMcastGroup		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.23
The value of tmnxMDAHiBwMcastGroup specifies the group of high bandwidth multicast traffic taps to which this tap belongs. A value of '0' specifies that this tap is not a member of any High Bandwidth Multicast group. On an IOM of type 'iom-10g', the value of tmnxMDAHiBwMcastGroup should be the same as the value of tmnxMDAHiBwMcastGroup set on the other MDA residing on the IOM if the tmnxMDAHiBwMcastSource is set to 'true'. Attempt to set to different values will result in an 'inconsistentValue' error. tmnxMDAHiBwMcastGroup must be set in the same SNMP request PDU with tmnxMDAHiBwMcastSource or an 'inconsistentValue' error will be returned.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..32

tmnxMDAClockMode		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.24
The value of tmnxMDAClockMode specifies the clock mode of the MDA. notApplicable - The MDA does not support any clock modes or domains. adaptive - The MDA is in 'adaptive' clock mode. This allows adaptive clock domains to be created. differential - The MDA is in 'differential clock mode. This allows differential clock domains to be created. The value of tmnxMDAClockMode can be changed when there are no ports created on the MDA. If there are ports created, a shutdown of the MDA is required in order to change the value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(0), adaptive(1), differential(2)

tmnxMDADiffTimestampFreq		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.25
The value of tmnxMDADiffTimestampFreq specifies the differential timestamp frequency of the differential clock on the MDA. The value must be a multiple of 8 KHz. This value can only be changed if the value of tmnxMDAClockMode is 'differential (2)' and there are no ports created on the MDA. If there are ports created, a shutdown of the MDA is required in order to change the value. If the value of tmnxMDAClockMode is 'differential (2) then the default is 103,680 KHz. If the value of tmnxMDAClockMode is not 'differential (2)' then this value is 0 KHz and cannot be changed.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 19440 | 77760 | 103680

tmnxMDAMcPathMgmtBwPlcyName		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.27
The value of tmnxMDAMcPathMgmtBwPlcyName specifies the multicast policy name configured on the MDA.
Status: current	Access: read-write
OBJECT-TYPE
	TNamedItem

tmnxMDAMcPathMgmtPriPathLimit		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.28
The value of tmnxMDAMcPathMgmtPriPathLimit specifies the primary path limit for the MDA.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 1..2000

tmnxMDAMcPathMgmtSecPathLimit		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.29
The value of tmnxMDAMcPathMgmtSecPathLimit specifies the secondary path limit for the MDA.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 1..2000

tmnxMDAMcPathMgmtAncPathLimit		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.30
The value of tmnxMDAMcPathMgmtAncPathLimit specifies the ancillary path limit for the MDA.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0 | 1..5000

tmnxMDAMcPathMgmtAdminState		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.31
The value of tmnxMDAMcPathMgmtAdminState specifies administrative state of this multicast path on the MDA.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAdminState

tmnxMDAIngNamedPoolPolicy		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.32
The value of tmnxMDAIngNamedPoolPolicy specifies a named pool policy associated with an MDA ingress context. The policy governs the way named pools are created at the MDA level.
Status: current	Access: read-write
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxMDAEgrNamedPoolPolicy		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.33
The value of tmnxMDAEgrNamedPoolPolicy specifies a named pool policy associated with an MDA egress context. The policy governs the way named pools are created at the MDA level.
Status: current	Access: read-write
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxMDAMcPathMgmtPriInUseBw		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.36
The value of tmnxMDAMcPathMgmtPriInUseBw indicates the in use ingress multicast bandwidth for the primary forwarding path.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

tmnxMDAMcPathMgmtSecInUseBw		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.37
The value of tmnxMDAMcPathMgmtSecInUseBw indicates the in use ingress multicast bandwidth for the secondary forwarding path.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

tmnxMDAMcPathMgmtAncInUseBw		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.38
The value of tmnxMDAMcPathMgmtAncInUseBw indicates the in use ingress multicast bandwidth for the ancillary forwarding path.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

tmnxMDAMcPathMgmtBlkHoleInUseBw		1.3.6.1.4.1.6527.3.1.2.2.3.8.1.39
The value of tmnxMDAMcPathMgmtBlkHoleInUseBw indicates the bandwidth of the ingress multicast traffic that is being black holed on the MDA.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

tmnxCardTypeTable		1.3.6.1.4.1.6527.3.1.2.2.3.9
The card type table has an entry for each Alcatel 7x50 SR series card model.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCardTypeEntry

tmnxCardTypeEntry		1.3.6.1.4.1.6527.3.1.2.2.3.9.1
Each row entry represents an Alcatel 7x50 SR series Card model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCardTypeEntry

tmnxCardTypeIndex		1.3.6.1.4.1.6527.3.1.2.2.3.9.1.1
The unique index value which identifies this type of Alcatel 7x50 SR series card model.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCardType

tmnxCardTypeName		1.3.6.1.4.1.6527.3.1.2.2.3.9.1.2
The administrative name that identifies this type of Alcatel 7x50 SR series card model. This name string may be used in CLI commands to specify a particular card model type.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxCardTypeDescription		1.3.6.1.4.1.6527.3.1.2.2.3.9.1.3
A detailed description of this Alcatel 7x50 SR series card model.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxCardTypeStatus		1.3.6.1.4.1.6527.3.1.2.2.3.9.1.4
When tmnxCardTypeStatus has a value of 'true' it indicates that this card model is supported in this revision of the management software. When it has a value of 'false' there is no support.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxMdaTypeTable		1.3.6.1.4.1.6527.3.1.2.2.3.10
The MDA type table has an entry for each Alcatel 7x50 SR series MDA card model.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxMdaTypeEntry

tmnxMdaTypeEntry		1.3.6.1.4.1.6527.3.1.2.2.3.10.1
Each row entry represents an Alcatel 7x50 SR series MDA card model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxMdaTypeEntry

tmnxMdaTypeIndex		1.3.6.1.4.1.6527.3.1.2.2.3.10.1.1
The unique index value which identifies this type of Alcatel 7x50 SR series MDA card model.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxMdaType

tmnxMdaTypeName		1.3.6.1.4.1.6527.3.1.2.2.3.10.1.2
The administrative name that identifies this type of Alcatel 7x50 SR series MDA card model. This name string may be used in CLI commands to specify a particular MDA card model type.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxMdaTypeDescription		1.3.6.1.4.1.6527.3.1.2.2.3.10.1.3
A detailed description of this Alcatel 7x50 SR series MDA card model.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxMdaTypeStatus		1.3.6.1.4.1.6527.3.1.2.2.3.10.1.4
When tmnxMdaTypeStatus has a value of 'true' it indicates that this MDA card model is supported in this revision of the management software. When it has a value of 'false' there is no support.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxSyncIfTimingTable		1.3.6.1.4.1.6527.3.1.2.2.3.11
The synchronous interface timing table has an entry for each cpm card in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxSyncIfTimingEntry

tmnxSyncIfTimingEntry		1.3.6.1.4.1.6527.3.1.2.2.3.11.1
A row represents the configuration of synchronous equipment timing subsystem (SETS) of the system. Entries cannot be created and deleted via SNMP SET operations. When a tmnxCpmCardEntry is created, a tmnxSyncIfTimingEntry is created. Note that the first Alcatel 7x50 SR series product release does not support configuration of synchronous equipment on the secondary CPM. All SNMP operations with tmnxCpmCardSlotNum of the secondary CPM will be denied. If the value of the reference source port is a valid Port ID then the reference is a port. If the value of the source hardware is a valid non-zero HWIndex then the source is the hardware specified by the HWIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSyncIfTimingEntry

tmnxSyncIfTimingRevert		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.1
The value of tmnxSyncIfTimingRevert indicates whether the reference source will revert to a higher priority source that has been re-validated or newly validated. The synchronous interface timing subsystem is by default non-revertive ('false').
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxSyncIfTimingRefOrder1		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.2
The value of tmnxSyncIfTimingRefOrder1 indicates the most preferred timing reference source. The synchronous equipment timing subsystem can lock to three different timing reference inputs, reference1, reference2 and bits. The subsystem chooses a reference based on priority.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefSource

tmnxSyncIfTimingRefOrder2		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.3
The value of tmnxSyncIfTimingRefOrder2 indicates the second most preferred timing reference for the synchronous equipment timing subsystem.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefSource

tmnxSyncIfTimingRef1SrcPort		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.4
The value of tmnxSyncIfTimingRef1SrcPort indicates the source port of the first timing reference. A value of '1e000000'H indicates that there is no source port for this reference.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxPortID

tmnxSyncIfTimingRef1AdminStatus		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.5
The value of tmnxSyncIfTimingRef1AdminStatus indicates the administrative status of the first timing reference.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxPortAdminStatus

tmnxSyncIfTimingRef1InUse		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.6
The value of tmnxSyncIfTimingRef1InUse indicates whether the first timing reference is presently being used by the synchronous timing subsystem. If it is in use, tmnxSyncIfTimingFreqOffset indicates the frequency offset for this reference.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxSyncIfTimingRef1Qualified		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.7
The value of tmnxSyncIfTimingRef1Qualified indicates whether the first timing reference is qualified for use by the synchronous timing subsystem. If tmnxSyncIfTimingRef1Qualified is set to 'not-qualified', then the object tmnxSyncIfTimingRef1Alarm gives the reason for disqualification.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefQualified

tmnxSyncIfTimingRef1Alarm		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.8
The value of tmnxSyncIfTimingRef1Alarm indicates the alarms on the first reference. If any of the bits is set to '1', then the first reference is disqualified by the timing subsystem and the value of tmnxSyncIfTimingRef1Qualified is set to 'not-qualified'. los - loss of signal oof - out of frequency range oopir - out of pull in range
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefAlarm

tmnxSyncIfTimingRef2SrcPort		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.9
The value of tmnxSyncIfTimingRef2SrcPort indicates the source port of the second timing reference. A value of '1e000000'H indicates that there is no source port for this reference.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxPortID

tmnxSyncIfTimingRef2AdminStatus		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.10
The value of tmnxSyncIfTimingRef2AdminStatus indicates the administrative status of the second timing reference.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxPortAdminStatus

tmnxSyncIfTimingRef2InUse		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.11
The value of tmnxSyncIfTimingRef2InUse indicates whether the second timing reference is presently being used by the synchronous timing subsystem.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxSyncIfTimingRef2Qualified		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.12
The value of tmnxSyncIfTimingRef2Qualified indicates whether the second timing reference is qualified for use by the synchronous timing subsystem. If tmnxSyncIfTimingRef2Qualified is 'not-qualified' then the object tmnxSyncIfTimingRef2Alarm gives the reason for disqualification.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefQualified

tmnxSyncIfTimingRef2Alarm		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.13
The value of tmnxSyncIfTimingRef2Alarm indicates the alarms on the second reference. If any of the bits is set to '1', then the second reference is disqualified by the timing subsystem and the value of tmnxSyncIfTimingRef2Qualified is set to 'not-qualified'. los - loss of signal oof - out of frequency range oopir - out of pull in range
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefAlarm

tmnxSyncIfTimingFreqOffset		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.14
The value of tmnxSyncIfTimingFreqOffset indicates the frequency offset of the current selected timing reference in parts per million (ppm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tmnxSyncIfTimingStatus		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.15
The value of tmnxSyncIfTimingStatus indicates the present status of the synchronous timing equipment subsystem (SETS).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-present(1), master-freerun(2), master-holdover(3), master-locked(4), slave(5), acquiring(6)

tmnxSyncIfTimingRefOrder3		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.16
The value of tmnxSyncIfTimingRefOrder3 is the third most preferred timing reference for the synchronous equipment timing subsystem.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefSource

tmnxSyncIfTimingBITSIfType		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.17
The value of tmnxSyncIfTimingBITSIfType indicates the interface type of the BITS (Building Integrated Timing Supply) timing reference. It also indicates the framing type of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxBITSIfType

tmnxSyncIfTimingBITSAdminStatus		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.18
The value of tmnxSyncIfTimingBITSAdminStatus indicates administrative status of the BITS (Building Integrated Timing Supply) timing reference.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxPortAdminStatus

tmnxSyncIfTimingBITSInUse		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.19
The value of tmnxSyncIfTimingBITSInUse indicates whether the BITS timing reference is presently being used by the synchronous timing subsystem. If it is in use, tmnxSyncIfTimingFreqOffset indicates the frequency offset for this reference.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxSyncIfTimingBITSQualified		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.20
The value of tmnxSyncIfTimingBITSQualified indicates whether the BITS timing reference is qualified for use by the synchronous timing subsystem. If tmnxSyncIfTimingBITSQualified is 'not-qualified', then the object tmnxSyncIfTimingBITSAlarm gives the reason for disqualification.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefQualified

tmnxSyncIfTimingBITSAlarm		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.21
The value of tmnxSyncIfTimingBITSAlarm indicates the alarms on the BITS reference. If any of the bits is set to '1', then the BITS reference is disqualified by the timing subsystem and the value of tmnxSyncIfTimingBITSQualified is set to 'not-qualified'.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxSETSRefAlarm

tmnxSyncIfTimingRef1SrcHw		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.22
The value of tmnxSyncIfTimingRef1SrcHw indicates the source HW index of the first timing reference if source is not a port.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndexOrZero

tmnxSyncIfTimingRef1BITSIfType		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.23
The value of tmnxSyncIfTimingRef1BITSIfType indicates the interface type of the first timing reference if the source is BITS. It also indicates the framing type of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxBITSIfType

tmnxSyncIfTimingRef2SrcHw		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.24
The value of tmnxSyncIfTimingRef2SrcHw indicates the source HW index of the second timing reference if source is not a port.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndexOrZero

tmnxSyncIfTimingRef2BITSIfType		1.3.6.1.4.1.6527.3.1.2.2.3.11.1.25
The value of tmnxSyncIfTimingRef2BITSIfType indicates the interface type of the second timing reference if the source is BITS. It also indicates the framing type of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxBITSIfType

tmnxChassisAdminCtrlObjs		1.3.6.1.4.1.6527.3.1.2.2.8.1
OBJECT IDENTIFIER

tmnxChassisAdminValueObjs		1.3.6.1.4.1.6527.3.1.2.2.8.2
OBJECT IDENTIFIER

tSyncIfTimingAdmTable		1.3.6.1.4.1.6527.3.1.2.2.8.2.1
Values for the synchronous interface timing for the chassis.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TSyncIfTimingAdmEntry

tSyncIfTimingAdmEntry		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1
Information about the synchronous interface timing. Entries are created by user. Entries are deleted by user. Note that the first Alcatel 7x50 SR series product release does not support configuration of synchronous timing equipment on the secondary CPM. All SNMP operations with tmnxCpmCardSlotNum of the secondary CPM will be denied. The 7x50 systems supports 3 timing references (reference1, reference2 and bits). The 7710 system only supports 2 timing references (reference1 and reference2). On 7710 system, references can be a source port or a BITS input on a CES CMA. If the value of the reference source port is a valid Port ID then the reference is a source port. If the value of the source hardware is a valid HWIndex of a CES CMA then the source is a BITS on the CES CMA.
Status: current	Access: not-accessible
OBJECT-TYPE
	TSyncIfTimingAdmEntry

tSyncIfTimingAdmRevert		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.1
The value of tSyncIfTimingAdmRevert specifies whether the reference source will revert to a higher priority source that has been re-validated or newly validated. The synchronous interface timing subsystem is by default non-revertive ('false').
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tSyncIfTimingAdmRefOrder1		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.2
The value of tSyncIfTimingAdmRefOrder1 specifies the most preferred timing reference source. The synchronous equipment timing subsystem can lock to three different timing reference inputs, reference1, reference2 and bits. The subsystem chooses a reference based on priority. tSyncIfTimingAdmRefOrder1 is used to configure the most preferred timing reference.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSETSRefSource

tSyncIfTimingAdmRefOrder2		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.3
The value of tSyncIfTimingAdmRefOrder2 specifies the second most preferred timing reference for the synchronous equipment timing subsystem.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSETSRefSource

tSyncIfTimingAdmRef1SrcPort		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.4
The value of tSyncIfTimingAdmRef1SrcPort specifies the source port of the first timing reference. This can only be set to a valid TmnxPortID if the value of tSyncIfTimingAdmRef1SrcHw is 0.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxPortID

tSyncIfTimingAdmRef1AdminStatus		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.5
The value of tSyncIfTimingAdmRef1AdminStatus specifies the desired administrative status of the first timing reference.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxPortAdminStatus

tSyncIfTimingAdmRef2SrcPort		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.6
The value of tSyncIfTimingAdmRef2SrcPort specifies the source port of the second timing reference. This can only be set to a valid TmnxPortID if the value of tSyncIfTimingAdmRef2SrcHw is 0.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxPortID

tSyncIfTimingAdmRef2AdminStatus		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.7
The value of tSyncIfTimingAdmRef2AdminStatus specifies the desired administrative status of the second timing reference.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxPortAdminStatus

tSyncIfTimingAdmChanged		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.8
The value of tSyncIfTimingAdmChanged is a bitmask that indicates which objects have been set, but not committed. bit values used here are: 0x0001: tSyncIfTimingAdmRevert 0x0002: tSyncIfTimingAdmRefOrder1 0x0004: tSyncIfTimingAdmRefOrder2 0x0008: tSyncIfTimingAdmRef1SrcPort 0x0010: tSyncIfTimingAdmRef1AdminStatus 0x0020: tSyncIfTimingAdmRef2SrcPort 0x0040: tSyncIfTimingAdmRef2AdminStatus 0x0080: tSyncIfTimingAdmRefOrder3 0x0100: tSyncIfTimingAdmBITSIfType 0x0200: tSyncIfTimingAdmBITSAdminStatus 0x0400: tSyncIfTimingAdmRef1SrcHw 0x0800: tSyncIfTimingAdmRef1BITSIfType 0x1000: tSyncIfTimingAdmRef2SrcHw 0x2000: tSyncIfTimingAdmRef2BITSIfType The agent sets these bits when an object in the row is set. This object is cleared to zero by setting tmnxChassisAdminControlApply to initialize(2) or commit(3).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

tSyncIfTimingAdmRefOrder3		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.9
The value of tSyncIfTimingAdmRefOrder3 indicates the third most preferred timing reference for the synchronous equipment timing subsystem.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSETSRefSource

tSyncIfTimingAdmBITSIfType		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.10
The value of tSyncIfTimingAdmBITSIfType specifies the interface type of the BITS (Building Integrated Timing Supply) timing reference.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxBITSIfType

tSyncIfTimingAdmBITSAdminStatus		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.11
The value of tSyncIfTimingAdmBITSAdminStatus specifies the desired administrative status of the BITS (Building Integrated Timing Supply) timing reference.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxPortAdminStatus

tSyncIfTimingAdmRef1SrcHw		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.12
The value of tSyncIfTimingAdmRef1SrcHw specifies the source HW Index of the first timing reference if the source is not a port. This can only be set to a valid HW Index if the value of tSyncIfTimingAdmRef1SrcPort is '1e000000'H.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxHwIndexOrZero

tSyncIfTimingAdmRef1BITSIfType		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.13
The value of tSyncIfTimingAdmRef1BITSIfType specifies the interface type of the first timing reference if the source is BITS.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxBITSIfType

tSyncIfTimingAdmRef2SrcHw		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.14
The value of tSyncIfTimingAdmRef2SrcHw specifies the source HW Index of the second timing reference if the source is not a port. This can only be set to a valid HW Index if the value of tSyncIfTimingAdmRef2SrcPort is '1e000000'H.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxHwIndexOrZero

tSyncIfTimingAdmRef2BITSIfType		1.3.6.1.4.1.6527.3.1.2.2.8.2.1.1.15
The value of tSyncIfTimingAdmRef2BITSIfType specifies the interface type of the second timing reference if the source is BITS.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxBITSIfType

tmnxChassisAdminOwner		1.3.6.1.4.1.6527.3.1.2.2.8.1.1
Who has last initialized the chassis administrative table, who is making all the changes, and who is expected to either commit or re-initialize (ABORT-TRANSACTION). tmnxChassisAdminOwner is advisory only. Before beginning a transaction, read tmnxChassisAdminOwner. if it is empty then proceed with the configuration. Set tmnxChassisAdminOwner after setting tmnxChassisAdminControlApply so that other users will be advised to not make changes to the Admin tables. Agent sets tmnxChassisAdminOwner to empty string after tmnxChassisAdminControlApply is set - either by user initializing or committing, or by agent timing out the uncommitted transactions (tmnxChassisAdminLastSetTimer).
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

tmnxChassisAdminControlApply		1.3.6.1.4.1.6527.3.1.2.2.8.1.2
This object controls the use of tmnxChassisAdminTable. when set to initialize(2), the objects in tmnxChassisAdminTable are set to the current Operational values, from the tmnxChassisTable. Any uncommitted changes are lost, so setting this value corresponds to both BEGIN-TRANSACTION and ABORT-TRANSACTION. when set to commit(3) (END-TRANSACTION), all of the objects from tmnxChassisAdminTable are copied to the corresponding tmnxChassisTable table objects.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), initialize(2), commit(3)

tmnxChassisAdminLastSetTimer		1.3.6.1.4.1.6527.3.1.2.2.8.1.3
The time remaining until the agent re-initializes the administrative tables. If tmnxChassisAdminControlApply is not set to commit(3) within tmnxChassisAdminLastSetTimeout centiseconds, the agent will set it to initialize(2) and all uncommitted changes will be lost. This way, uncommitted changes from failed (uncompleted) change sets will eventually be removed, and another transaction can safely begin. this object is reset to tmnxChassisAdminLastSetTimeout after SNMP SET operation to any of the tmnxChassisAdminValue tables.
Status: current	Access: read-only
OBJECT-TYPE
	TimeInterval

tmnxChassisAdminLastSetTimeout		1.3.6.1.4.1.6527.3.1.2.2.8.1.4
Timeout for tmnxChassisAdminLastSetTimer. The value zero is not allowed.
Status: current	Access: read-write
OBJECT-TYPE
	TimeInterval

tmnxCcagTable		1.3.6.1.4.1.6527.3.1.2.2.3.12
The tmnxCcagTable has an entry for each Cross Connect Aggregation Group,CCAG, configured on this system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCcagEntry

tmnxCcagEntry		1.3.6.1.4.1.6527.3.1.2.2.3.12.1
Each row entry represents a particular CCAG. Entries are created/deleted by the user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcagEntry

tmnxCcagId		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.1
The value of tmnxCcagId is used to index into the tmnxCcagTable. It uniquely identifies a CCAG entry as configured on this system.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcagId

tmnxCcagRowStatus		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.2
The value of tmnxCcagRowStatus specifies the row status. It allows entries to be created and deleted in the tmnxCcagTable. tmnxCcagRowStatus does not support createAndWait. The status can only be active or notInService.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxCcagLastChanged		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.3
The value of tmnxCcagLastChanged indicates the time this row was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxCcagDescription		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.4
The value of tmnxCcagDescription specifies a user provided description string of this CCAG entry.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

tmnxCcagAdminStatus		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.5
The value of tmnxCcagAdminStatus specifies the desired state of this CCAG.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAdminState

tmnxCcagOperStatus		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.6
The value of tmnxCcagOperStatus indicates the operational state of this CCAG.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxOperState

tmnxCcagCcaRate		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.7
The value of tmnxCcagCcaRate specifies the maximum forwarding rate for each CCA member within the CCAG.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxCcagRate

tmnxCcagAccessAdaptQos		1.3.6.1.4.1.6527.3.1.2.2.3.12.1.8
The value of tmnxCcagAccessAdaptQos specifies how the CCAG SAP queue and virtual scheduler buffering and rate parameters are adapted over multiple active CCAs. link (1) - The CCAG will create the SAP queues and virtual schedulers on each CCA with the actual parameters specified in the tmnxCcagPathCcTable. distribute (2) - Each CCA will receive a portion of the parameters specified in the tmnxCcagPathCcTable.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	link(1), distribute(2)

tmnxCcagPathTable		1.3.6.1.4.1.6527.3.1.2.2.3.13
The tmnxCcagPathTable has an entry for each Cross Connect Aggregation Group, CCAG, path configured on this system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCcagPathEntry

tmnxCcagPathEntry		1.3.6.1.4.1.6527.3.1.2.2.3.13.1
Each row entry represents a particular CCAG Path. Entries are created/deleted by the user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcagPathEntry

tmnxCcagPathId		1.3.6.1.4.1.6527.3.1.2.2.3.13.1.1
The value of tmnxCcagPathId is used as the secondary index into the tmnxCcagPathTable. Along with tmnxCcagId, it uniquely identifies a specific path, alpha or beta, on a CCAG.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	alpha(1), beta(2)

tmnxCcagPathLastChanged		1.3.6.1.4.1.6527.3.1.2.2.3.13.1.2
The value of tmnxCcagPathLastChanged indicates the time this row was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxCcagPathRate		1.3.6.1.4.1.6527.3.1.2.2.3.13.1.3
The value of tmnxCcagPathRate specifies the bandwidth rate limitation for this path on each member cross connect adaptor, CCA, in the CCAG.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxCcagRate

tmnxCcagPathRateOption		1.3.6.1.4.1.6527.3.1.2.2.3.13.1.4
The value of tmnxCcagPathRateOption specifies whether the rate in tmnxCcagPathRate is defined as an aggregate path rate for all CCAs in the CCAG or as a per CCA path rate.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxCcagRateOption

tmnxCcagPathWeight		1.3.6.1.4.1.6527.3.1.2.2.3.13.1.5
The value of tmnxCcagPathWeight specifies the scheduling percentage for this path. It is applied to all CCAs in the CCAG membership list for this path.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..100

tmnxCcagPathCcTable		1.3.6.1.4.1.6527.3.1.2.2.3.14
The tmnxCcagPathCcTable has an entry for each type of Cross Connection on a Cross Connect Aggregation Group Path configured on this system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxCcagPathCcEntry

tmnxCcagPathCcEntry		1.3.6.1.4.1.6527.3.1.2.2.3.14.1
Each row entry represents a particular CCAG Path Cross Connect. Entries are created/deleted by the user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxCcagPathCcEntry

tmnxCcagPathCcType		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.1
The value of tmnxCcagPathCcType is used as a third index into the tmnxCcagPathCcTable. Along with tmnxCcagId and tmnxCcagPathId, it uniquely identifies a cross connection type on a specific path in a particular CCAG. The types are: sapsap (1): the cross connection is between two saps, where both services are access. sapnet (2): the cross connection is between a sap and a network service. netsap (3): the cross connection is between a network and a sap service.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	sapsap(1), sapnet(2), netsap(3)

tmnxCcagPathCcLastChanged		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.2
The value of tmnxCcagPathCcLastChanged indicates the time this row was last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxCcagPathCcEgrPoolResvCbs		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.3
The value of tmnxCcagPathCcEgrPoolResvCbs specifies the percentage of pool size reserved for the committed burst size, CBS. The value '-1' implies that the reserved CBS should be computed as the sum of the CBS requested by the entities using this pool if the application point is 'network'. For 'access' application points the value '-1' means a default of 30%.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	-1 | 0..100

tmnxCcagPathCcEgrPoolSlpPlcy		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.4
The value of tmnxCcagPathCcEgrPoolSlpPlcy specifies the slope policy being used for the egress pool. The Slope policies define the nature of the RED Slopes for the high and the low priority traffic.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItem

tmnxCcagPathCcIngPoolResvCbs		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.5
The value of tmnxCcagPathCcIngPoolResvCbs specifies the percentage of pool size reserved for the committed burst size, CBS. The value '-1' implies that the reserved CBS should be computed as the sum of the CBS requested by the entities using this pool if the application point is 'network'. For 'access' application points the value '-1' means a default of 30%. tmnxCcagPathCcIngPoolResvCbs does not apply to tmnxCcagPathCcType 'netsap'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	-1 | 0..100

tmnxCcagPathCcIngPoolSlpPlcy		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.6
The value of tmnxCcagPathCcIngPoolSlpPlcy specifies the slope policy being used for the ingress pool. The Slope policies define the nature of the RED Slopes for the high and the low priority traffic. tmnxCcagPathCcIngPoolSlpPlcy does not apply to tmnxCcagPathCcType 'netsap'.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItem

tmnxCcagPathCcAcctPolicyId		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.7
The value of tmnxCcagPathCcAcctPolicyId specifies the accounting policy which must be defined prior to associating it with the port. A non-zero value indicates the tmnxLogApPolicyId index identifying the policy entry in the tmnxLogApTable from the TIMETRA-LOG-MIB which is associated with this port. A zero value indicates that there is no accounting policy associated with this port. It is only meaningful when the tmnxCcagPathCcType is 'netsap'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..99

tmnxCcagPathCcCollectStats		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.8
The value of tmnxCcagPathCcCollectStats specifies whether the collection of accounting and statistical data for the network port is enabled/disabled, 'true'/'false'. When applying accounting policies the data by default will be collected in the appropriate records and written to the designated billing file. When the value is set to false, the statistics are still accumulated by the IOM cards, however, the CPU will not obtain the results and write them to the billing file. If the value of tmnxCcagPathCcType is not 'netsap', the value of this object is meaningless and an attempt to set it will result in an inconsistentValue error.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxCcagPathCcQueuePlcy		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.9
The value of tmnxCcagPathCcQueuePlcy specifies the network egress queue policy. If the value of tmnxCcagPathCcType is not 'netsap', the value of this object is meaningless and an attempt to set it will result in an inconsistentValue error.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItem

tmnxCcagPathCcMac		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.10
The value of tmnxCcagPathCcMac specifies the MAC address of the virtual LAG that maps to tmnxCcagPathId and tmnxCcagPathCcType. The default value of this object is derived from the chassis MAC address pool.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

tmnxCcagPathCcMtu		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.11
The value of tmnxCcagPathCcMtu specifies the MTU of the path indexed by tmnxCcagId, tmnxCcagPathId, and tmnxCcagPathCcType. When the value is '0', the real MTU is calculated internally.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

tmnxCcagPathCcUserAssignedMac		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.12
The value of tmnxCcagPathCcUserAssignedMac indicates whether the value of tmnxCcagPathCcMac has been explicitly assigned or inherited from tmnxCcagPathCcHwMac, 'true' and 'false', respectively.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxCcagPathCcHwMac		1.3.6.1.4.1.6527.3.1.2.2.3.14.1.13
The value of tmnxCcagPathCcHwMac is the system assigned MAC address of the virtual LAG that maps to tmnxCcagPathId and tmnxCcagPathCcType. When tmnxCcagPathCcUserAssignedMac is 'false', tmnxCcagPathCcMac inherits its value from this object.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

tmnxMcmTable		1.3.6.1.4.1.6527.3.1.2.2.3.15
The tmnxMcmTable has an entry for each Mda Carrier module (MCM) on the 7710 system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxMcmEntry

tmnxMcmEntry		1.3.6.1.4.1.6527.3.1.2.2.3.15.1
Each row entry represents a MCM in a chassis in the 7710 system. Entries in the table cannot be created and deleted via SNMP SET operations. When a tmnxChassisEntry is created, a tmnxMcmEntry is created in the chassis. Before a tmnxChassisEntry can be deleted, each tmnxMcmEntry for the chassis must be in the proper state for removal.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxMcmEntry

tmnxMcmSlotNum		1.3.6.1.4.1.6527.3.1.2.2.3.15.1.1
The unique value which identifies this MDA slot within a specific IOM card in the system. Since the MCM occupies two MDA slots in the chassis this value can only be an odd number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..16

tmnxMcmSupportedTypes		1.3.6.1.4.1.6527.3.1.2.2.3.15.1.2
A bit-mask that specifies what MCM types can be physically supported in this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxMcmType

tmnxMcmAssignedType		1.3.6.1.4.1.6527.3.1.2.2.3.15.1.3
A bit-mask that identifies the administratively assigned (pre-provisioned) MCM type that should occupy this chassis. If tmnxMcmAssignedType has a value of 'unassigned', this slot has not yet been pre-provisioned. There must not be more than one bit set at a time in tmnxMcmAssignedType.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxMcmType

tmnxMcmEquippedType		1.3.6.1.4.1.6527.3.1.2.2.3.15.1.4
A bit-mask that identifies the MCM type that is physically inserted into this chassis. If the chassis has been pre-provisioned, tmnxMcmAssignedType is not equal 'unassigned', and the value of tmnxMcmEquippedType is not the same as tmnxMcmAssignedType, a mis-match alarm will be raised. If the chassis has not been pre-provisioned, and the value of tmnxMcmEquippedType is not one of the supported types as specified by tmnxMcmSupportedTypes, a mis-match alarm will be raised. There will not be more than one bit set at a time in tmnxMcmEquippedType.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxMcmType

tmnxMcmHwIndex		1.3.6.1.4.1.6527.3.1.2.2.3.15.1.5
The value of tmnxMcmHwIndex is the index into the tmnxHwTable for the row entry that represents the hardware component information for this MCM.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxHwIndex

tmnxMcmTypeTable		1.3.6.1.4.1.6527.3.1.2.2.3.16
The card type table has an entry for each Alcatel 7710 series Mda Carrier Module (MCM) model.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxMcmTypeEntry

tmnxMcmTypeEntry		1.3.6.1.4.1.6527.3.1.2.2.3.16.1
Each row entry represents an Alcatel 7710 series MCM model. Rows in this table are created by the agent at initialization and cannot be created or destroyed by SNMP Get or Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxMcmTypeEntry

tmnxMcmTypeIndex		1.3.6.1.4.1.6527.3.1.2.2.3.16.1.1
The unique index value which identifies this type of Alcatel 7710 series MCM model.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxMcmType

tmnxMcmTypeName		1.3.6.1.4.1.6527.3.1.2.2.3.16.1.2
The administrative name that identifies this type of Alcatel 7710 series MCM model. This name string may be used in CLI commands to specify a particular card model type.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxMcmTypeDescription		1.3.6.1.4.1.6527.3.1.2.2.3.16.1.3
A detailed description of this Alcatel 7710 series MCM model.
Status: current	Access: read-only
OBJECT-TYPE
	TItemDescription

tmnxMcmTypeStatus		1.3.6.1.4.1.6527.3.1.2.2.3.16.1.4
When tmnxMcmTypeStatus has a value of 'true' it indicates that this MCM is supported in this revision of the management software. When it has a value of 'false' there is no support.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxEqNotificationRow		1.3.6.1.4.1.6527.3.1.2.2.6.1
used by tmnx chassis Notifications, the OID indicates the table and entry.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	RowPointer

tmnxEqTypeNotificationRow		1.3.6.1.4.1.6527.3.1.2.2.6.2
used by tmnx chassis notifications, the OID indicates the table and entry with the equipment model type information.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	RowPointer

tmnxChassisNotifyChassisId		1.3.6.1.4.1.6527.3.1.2.2.6.3
Used by tmnx chassis and port Notifications, indicates the chassis associated with the alarm.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxChassisIndex

tmnxChassisNotifyHwIndex		1.3.6.1.4.1.6527.3.1.2.2.6.4
Used by tmnx chassis and port Notifications, indicates the entry in the tmnxHwTable for the hardware component associated with an alarm.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxHwIndex

tmnxRedSecondaryCPMStatus		1.3.6.1.4.1.6527.3.1.2.2.6.5
Used by the tmnxRedSecondaryCPMStatusChange Notification, indicates the status of the secondary CPM.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	online(1), offline(2), fail(3)

tmnxChassisNotifyOID		1.3.6.1.4.1.6527.3.1.2.2.6.6
Used by the tmnxChassisNotificationClear trap, the OID identifies the trap which is getting cleared.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OBJECT IDENTIFIER

tmnxSyncIfTimingNotifyAlarm		1.3.6.1.4.1.6527.3.1.2.2.6.7
Used by tmnx Synchronous interface timing notifications, the value of tmnxSyncIfTimingNotifyAlarm indicates the reason a timing reference alarm has been raised.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	notUsed(0), los(1), oof(2), oopir(3)

tmnxChassisNotifyMismatchedVer		1.3.6.1.4.1.6527.3.1.2.2.6.8
Used by tmnxPeSoftwareVersionMismatch, the value of tmnxChassisNotifyMismatchedVer indicates the software version of the mismatched CPM/IOM card.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

tmnxChassisNotifySoftwareLocation		1.3.6.1.4.1.6527.3.1.2.2.6.9
Used by tmnxPeSoftwareLoadFailed, the value of tmnxChassisNotifySoftwareLocation contains the location of the software.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

tmnxChassisNotifyCardFailureReason		1.3.6.1.4.1.6527.3.1.2.2.6.10
Used by tmnxEqCardFailure, the value of tmnxChassisNotifyCardFailureReason contains the reason for card failure.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

tmnxChassisNotifyCardName		1.3.6.1.4.1.6527.3.1.2.2.6.11
Used by tmnxEqCardInserted and tmnxEqCardRemoved, the value of tmnxChassisNotifyCardName specifies the name of the affected card.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(1..32)

tmnxHwConfigChange		1.3.6.1.4.1.6527.3.1.3.2.1.0.1
A tmnxHwConfigChange notification is generated when the value of tmnxHwLastChange is updated. It can be used by the NMS to trigger maintenance polls of the hardware configuration information. Only one tmnxHwConfigChange notification event will be generated in a 5 second throttling time period. A notification event is the transmission of a single trap to a list of notification destinations configured in the SNMP-TARGET-MIB. If additional hardware configuration change occurs within the throttling period, the notification events for these changes are suppressed until the throttling period expires. At the end of the throttling period, one notification event is generated if any addition configuration changes occurred within the just completed throttling period and another throttling period is started. The NMS should periodically check the value of tmnxHwConfigChange to detect any missed tmnxHwConfigChange traps. This notification was made obsolete in the 2.1 release. The tmnxHwConfigChange notification has been replaced with the generic change notifications from the TIMETRA-SYSTEM-MIB: tmnxConfigModify, tmnxConfigCreate, tmnxConfigDelete, tmnxStateChange.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEnvTempTooHigh		1.3.6.1.4.1.6527.3.1.3.2.1.0.2
Generated when the temperature sensor reading on an equipment object is greater than its configured threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqPowerSupplyFailure		1.3.6.1.4.1.6527.3.1.3.2.1.0.3
Generated when one of the chassis's power supplies fails.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqPowerSupplyInserted		1.3.6.1.4.1.6527.3.1.3.2.1.0.4
Generated when one of the chassis's power supplies is inserted.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqPowerSupplyRemoved		1.3.6.1.4.1.6527.3.1.3.2.1.0.5
Generated when one of the chassis's power supplies is removed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqFanFailure		1.3.6.1.4.1.6527.3.1.3.2.1.0.6
Generated when one of the fans in a fan tray has failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqCardFailure		1.3.6.1.4.1.6527.3.1.3.2.1.0.7
Generated when one of the cards in a chassis has failed. The card type may be IOM, Fabric, MDA, MCM, CCM, CPM module, compact flash module, etc. tmnxChassisNotifyCardFailureReason contains the reason for card failure.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqCardInserted		1.3.6.1.4.1.6527.3.1.3.2.1.0.8
Generated when a card is inserted into the chassis. The card type may be IOM, Fabric, MDA, MCM, CCM CPM module, compact flash module, etc.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqCardRemoved		1.3.6.1.4.1.6527.3.1.3.2.1.0.9
Generated when a card is removed from the chassis. The card type may be IOM, Fabric, MDA, MCM, CCM, CPM module, compact flash module, etc.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqWrongCard		1.3.6.1.4.1.6527.3.1.3.2.1.0.10
Generated when the wrong type of card is inserted into a slot of the chassis. Even though a card may be physically supported by the slot, it may have been administratively configured to allow only certain card types in a particular slot location. The card type may be IOM, Fabric, MDA, MCM, CPM module, etc.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqCpuFailure		1.3.6.1.4.1.6527.3.1.3.2.1.0.11
Generated when a failure is detected for a CPU on an IOM card or CPM module. This notification was made obsolete in the 2.1 release. A cpu failure on a CPM card is detected by the hardware bootup and is indicated by the boot diagnostic display. If there is no working redundant CPM card, the system does not come up. A failure of an IOM card or standby redundant CPM card causes the tmnxEqCardFailure notification to be sent.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqMemoryFailure		1.3.6.1.4.1.6527.3.1.3.2.1.0.12
Generated when a memory module failure is detected for an IOM card or CPM module. This notification was made obsolete in the 2.1 release. A failure of the memory device is detected by the hardware bootup and is indicated by the boot diagnostic display. If there is no working redundant CPM card, the system does not come up. A failure of the memory device during run-time causes the system to fail and the 'admin tech-support' information to be saved. A failure of an IOM card or standby redundant CPM card causes the tmnxEqCardFailure notification to be sent.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqBackdoorBusFailure		1.3.6.1.4.1.6527.3.1.3.2.1.0.13
Generated when the backdoor bus has failed. This notification was made obsolete in the 2.1 release.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeSoftwareError		1.3.6.1.4.1.6527.3.1.3.2.1.0.14
Generated when a software error has been detected. This notification was made obsolete in the 2.1 release. Many of the other notifications more specifically indicate detection of some type of software error. The 'admin tech-support' information helps developers diagnose a failure of the software in the field.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeSoftwareAbnormalHalt		1.3.6.1.4.1.6527.3.1.3.2.1.0.15
Generated when the software has abnormally terminated. This notification was made obsolete in the 2.1 release. Many of the other notifications more specifically indicate detection of some type of software error. The 'admin tech-support' information helps developers diagnose a failure of the software in the field.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeSoftwareVersionMismatch		1.3.6.1.4.1.6527.3.1.3.2.1.0.16
Generated when there is a mismatch between software versions of the active CPM and standby CPM or the CPM and IOM. tmnxChassisNotifyHwIndex identifies the mismatched CPM/IOM card and tmnxChassisNotifyMismatchedVer will contain the version of the mismatched card. The tmnxHwSoftwareCodeVersion object will contain the expected version.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeOutOfMemory		1.3.6.1.4.1.6527.3.1.3.2.1.0.17
Generated when there is an out of memory error detected. This notification was made obsolete in the 2.1 release. The tmnxPeOutOfMemory notification has been replaced with the module specific notification from the TIMETRA-SYSTEM-MIB: tmnxModuleMallocFailed.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeConfigurationError		1.3.6.1.4.1.6527.3.1.3.2.1.0.18
Generated when a configuration error has been detected. This notification was made obsolete in the 2.1 release. Many other notifications more specifically indicate detection of a configuration error. In most cases the SNMP SET request that tries to make an invalid configuration results in an error response. In some cases the configuration parameters are valid and the SNMP SET request succeeds but the system cannot successfully apply the new parameters. The affected object may then put into an operational 'down' state. A state change notification such as tmnxStateChange or a more specific notification is sent to alert about the problem. For example, an attempt to create an event log with a file-type destination when the specified cflash media is full or not present results in TIMETRA-LOG-MIB notifications tmnxLogSpaceContention, tmnxLogAdminLocFailed, or tmnxLogBackupLocFailed.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeStorageProblem		1.3.6.1.4.1.6527.3.1.3.2.1.0.19
Generated when there is a storage capacity problem. This notification was made obsolete in the 2.1 release. The only 'storage' devices on the SR7750 are the cflash drives. Cflash write errors cause a tmnxEqFlashDataLoss notification to be sent. The tmnxEqFlashDiskFull notification is sent when the driver detects that the cflash device is full.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeCpuCyclesExceeded		1.3.6.1.4.1.6527.3.1.3.2.1.0.20
Generated when the CPU cycle usage limit has been exceeded. This notification was made obsolete in the 2.1 release. It does not apply. The SR7750 software architecture does not restrict CPU cycles used by a specific code module.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxRedPrimaryCPMFail		1.3.6.1.4.1.6527.3.1.3.2.1.0.21
Generated when the primary CPM fails.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxRedSecondaryCPMStatusChange		1.3.6.1.4.1.6527.3.1.3.2.1.0.22
Generated when there is a change in the secondary CPM status. This notification was made obsolete in the 2.1 release. There is no way to administratively enable or disable CPM cards so there is no need for a status change event for administrative state changes. Operational changes detected about the standby CPM card are indicated by more specific notifications such as tmnxEqCardFailure, tmnxEqCardRemoved, tmnxEqCardInserted TIMETRA-SYSTEM-MIB::ssiRedStandbyReady, TIMETRA-SYSTEM-MIB::ssiRedStandbySyncLost, and TIMETRA-SYSTEM-MIB::ssiRedStandbySyncLost.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxRedRestoreSuccess		1.3.6.1.4.1.6527.3.1.3.2.1.0.23
Generated when the secondary CPM successfully restores the config and state. This notification was made obsolete in the 2.1 release. It does not apply. This event was originally created for an early redundancy mechanism that was never released.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxRedRestoreFail		1.3.6.1.4.1.6527.3.1.3.2.1.0.24
Generated when the secondary CPM fails to restore the config and state. This notification was made obsolete in the 2.1 release. It does not apply. This event was originally created for an early redundancy mechanism that was never released.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxChassisNotificationClear		1.3.6.1.4.1.6527.3.1.3.2.1.0.25
A trap indicating the clear of a chassis notification identified by tmnxChassisNotifyOID.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingHoldover		1.3.6.1.4.1.6527.3.1.3.2.1.0.26
Generated when the synchronous equipment timing subsystem transitions into a holdover state. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingHoldoverClear		1.3.6.1.4.1.6527.3.1.3.2.1.0.27
Generated when the synchronous equipment timing subsystem transitions out of the holdover state. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingRef1Alarm		1.3.6.1.4.1.6527.3.1.3.2.1.0.28
Generated when an alarm condition on the first timing reference is detected. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingRef1AlarmClear		1.3.6.1.4.1.6527.3.1.3.2.1.0.29
Generated when an alarm condition on the first timing reference is cleared. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingRef2Alarm		1.3.6.1.4.1.6527.3.1.3.2.1.0.30
Generated when an alarm condition on the second timing reference is detected. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingRef2AlarmClear		1.3.6.1.4.1.6527.3.1.3.2.1.0.31
Generated when an alarm condition on the second timing reference is cleared. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqFlashDataLoss		1.3.6.1.4.1.6527.3.1.3.2.1.0.32
tmnxEqFlashDataLoss is generated when there was an error while data was getting written on to the compact flash. This notification indicates a probable data loss.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqFlashDiskFull		1.3.6.1.4.1.6527.3.1.3.2.1.0.33
tmnxEqFlashDiskFull is generated when there is no space left on the compact flash. No more data can be written to it.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeSoftwareLoadFailed		1.3.6.1.4.1.6527.3.1.3.2.1.0.34
Generated when the CPM fails to load the software from a specified location. tmnxChassisNotifyHwIndex identifies the card for which the software load failed and tmnxChassisNotifySoftwareLocation contains the location from where the software load was attempted.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeBootloaderVersionMismatch		1.3.6.1.4.1.6527.3.1.3.2.1.0.35
Generated when there is a mismatch between the CPM and boot loader versions. tmnxChassisNotifyHwIndex identifies the CPM card. tmnxChassisNotifyMismatchedVer contains the mismatched version of bootloader and tmnxHwSoftwareCodeVersion contains the expected version of the bootloader.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeBootromVersionMismatch		1.3.6.1.4.1.6527.3.1.3.2.1.0.36
Generated when there is a mismatch between the boot rom versions. tmnxChassisNotifyHwIndex identifies the IOM card. tmnxChassisNotifyMismatchedVer contains the mismatched version of bootrom and tmnxHwSoftwareCodeVersion contains the expected version of the bootrom.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxPeFPGAVersionMismatch		1.3.6.1.4.1.6527.3.1.3.2.1.0.37
Generated when there is a mismatch between the FPGA versions. tmnxChassisNotifyHwIndex identifies the IOM card. tmnxChassisNotifyMismatchedVer contains the mismatched version of FPGA and tmnxHwSoftwareCodeVersion contains the expected version of the FPGA.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingBITSAlarm		1.3.6.1.4.1.6527.3.1.3.2.1.0.38
Generated when an alarm condition on the BITS timing reference is detected. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqSyncIfTimingBITSAlarmClear		1.3.6.1.4.1.6527.3.1.3.2.1.0.39
Generated when an alarm condition on the BITS timing reference is cleared. This notification will have the same indices as those of the tmnxCpmCardTable.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqCardFirmwareUpgraded		1.3.6.1.4.1.6527.3.1.3.2.1.0.40
Generated when a card is hot-inserted into the chassis and its firmware is automatically upgraded. The card type may be IOM or CPM module.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxChassisUpgradeInProgress		1.3.6.1.4.1.6527.3.1.3.2.1.0.41
The tmnxChassisUpgradeInProgress notification is generated only after a CPM switchover occurs and the new active CPM is running new software, while the IOMs are still running old software. This is the start of the upgrade process. The tmnxChassisUpgradeInProgress notification will continue to be generated every 30 minutes while at least one IOM is still running older software.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxChassisUpgradeComplete		1.3.6.1.4.1.6527.3.1.3.2.1.0.42
The tmnxChassisUpgradeComplete notification is generated to indicate that all the IOMs are running matching software version in reference to the active CPM software version changed as part of the upgrade process.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxChassisHiBwMcastAlarm		1.3.6.1.4.1.6527.3.1.3.2.1.0.43
The tmnxChassisHiBwMcastAlarm notification is generated when a plane is shared by more than one high bandwidth multicast tap.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxEqMdaCfgNotCompatible		1.3.6.1.4.1.6527.3.1.3.2.1.0.44
Generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the current configuration on the MDA's ports is not compatible with the inserted MDA.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxChassisCompliances		1.3.6.1.4.1.6527.3.1.1.2.1.1
OBJECT IDENTIFIER

tmnxChassisGroups		1.3.6.1.4.1.6527.3.1.1.2.1.2
OBJECT IDENTIFIER

tmnxChassisV4v0Compliance		1.3.6.1.4.1.6527.3.1.1.2.1.1.4
The compliance statement for management of chassis features in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassisV5v0Compliance		1.3.6.1.4.1.6527.3.1.1.2.1.1.6
The compliance statement for management of chassis features in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassis7750V6v0Compliance		1.3.6.1.4.1.6527.3.1.1.2.1.1.7
The compliance statement for management of chassis features on the 7750 in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassis7450V6v0Compliance		1.3.6.1.4.1.6527.3.1.1.2.1.1.8
The compliance statement for management of chassis features on the 7450 in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassisComp7710		1.3.6.1.4.1.6527.3.1.1.2.1.1.5
OBJECT IDENTIFIER

tmnxChassisComp7710V3v0		1.3.6.1.4.1.6527.3.1.1.2.1.1.5.1
The compliance statement for management of chassis features for the 7710 in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassisComp7710V5v0		1.3.6.1.4.1.6527.3.1.1.2.1.1.5.2
The compliance statement for management of chassis features for the 7710 in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassisComp7710V6v0		1.3.6.1.4.1.6527.3.1.1.2.1.1.5.3
The compliance statement for management of chassis features for the 7710 in the ALCATEL-IND1-TIMETRA-CHASSIS-MIB.
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxChassisNotifyObjsGroup		1.3.6.1.4.1.6527.3.1.1.2.1.2.4
The group of objects supporting chassis hardware notifications on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisNotifyObsoleteGroup		1.3.6.1.4.1.6527.3.1.1.2.1.2.7
The group of notifications supporting the management of chassis hardware made obsolete for revision 2.1 on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxChassisV3v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.9
The group of objects supporting management of chassis hardware capabilities on release 3.0 of Alcatel 7x50 SR series systems.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxMDAV3v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.10
The group of objects supporting management of MDAs on Alcatel 7x50 SR series systems.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisObsoleteGroup		1.3.6.1.4.1.6527.3.1.1.2.1.2.11
The group of objects supporting the allowed types of CPM cards, IOM cards and MDA made obsolete for revision 3.0 on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxCardV3v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.12
The group of objects supporting management of hardware cards on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxMDAV4v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.13
The group of objects supporting management of MDAs for release 4.0 on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisNotificationV4v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.14
The group of notifications supporting the management of chassis hardware for release 4.0 on Alcatel 7x50 SR series systems.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnx7710HwV3v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.15
The group of objects supporting management of hardware specific to the Alcatel 7710 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisV5v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.16
The group of objects supporting management of chassis hardware capabilities on release 5.0 of Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisV5v0ObsoleteGroup		1.3.6.1.4.1.6527.3.1.1.2.1.2.17
The group of onbsolete objects for managing the chassis hardware capabilities on release 5.0 of Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnx77x0CESMDAV6v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.18
The group of objects supporting management of CES MDAs for release 6.0 on Alcatel 77x0 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisNotificationV3v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.20
The group of notifications supporting the management of chassis hardware for release 3.0 on Alcatel 7x50 SR series systems.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxChassisNotificationV6v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.21
The group of notifications supporting the management of chassis hardware for release 6.0 on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnx7710SETSRefSrcHwV6v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.22
The group of objects supporting management of 'Synchronous Equipment Timing' (SETS) when the references are of type 'Building Integrated Timing Supply' (BITS) for release 6.0 on Alcatel 7710 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxMDAMcPathMgmtV6v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.24
The group of objects supporting management of Multicast Path Management feature for release 6.0 on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxCardV6v0NamedPoolPlcyGroup		1.3.6.1.4.1.6527.3.1.1.2.1.2.25
The group of objects supporting named buffer pools for release 6.0 on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxChassisNotifyObjsV6v0Group		1.3.6.1.4.1.6527.3.1.1.2.1.2.26
The group of objects added in 6.0 release to support chassis hardware notifications on Alcatel 7x50 SR series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP