ALCATEL-IND1-QOS-MIB

File: ALCATEL-IND1-QOS-MIB.mib (433660 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
ALCATEL-IND1-BASE IF-MIB IPV6-TC

Imported symbols

OBJECT-TYPE OBJECT-IDENTITY MODULE-IDENTITY
Counter32 Counter64 Integer32
IpAddress OBJECT-GROUP MODULE-COMPLIANCE
DisplayString MacAddress RowStatus
softentIND1QoS InterfaceIndex Ipv6Address

Defined Types

QoSRuleEntry  
SEQUENCE    
  alaQoSRuleName DisplayString
  alaQoSRuleEnabled INTEGER
  alaQoSRuleSource INTEGER
  alaQoSRulePrecedence Integer32
  alaQoSRuleCondition DisplayString
  alaQoSRuleAction DisplayString
  alaQoSRuleReflexive INTEGER
  alaQoSRuleSave INTEGER
  alaQoSRuleLog INTEGER
  alaQoSRuleMatches Counter32
  alaQoSRuleEnforced INTEGER
  alaQoSRuleActive INTEGER
  alaQoSRuleRowStatus RowStatus
  alaQoSRuleValidityPeriod DisplayString
  alaQoSRuleValidityPeriodStatus INTEGER
  alaQoSRuleLogInterval Integer32
  alaQoSRuleCountType INTEGER
  alaQoSRulePacketCount Counter64
  alaQoSRuleByteCount Counter64
  alaQoSRuleExcessPacketCount Counter64
  alaQoSRuleExcessByteCount Counter64
  alaQoSRuleType Integer32
  alaQoSRuleTrapEvents INTEGER
  alaQoSRuleDefaultList INTEGER
  alaQoSRuleGreenCount Counter64
  alaQoSRuleYellowCount Counter64
  alaQoSRuleRedCount Counter64
  alaQoSRuleNonGreenCount Counter64
  alaQoSRuleNonRedCount Counter64

QoSAppliedRuleEntry  
SEQUENCE    
  alaQoSAppliedRuleName DisplayString
  alaQoSAppliedRuleEnabled INTEGER
  alaQoSAppliedRuleSource INTEGER
  alaQoSAppliedRulePrecedence Integer32
  alaQoSAppliedRuleCondition DisplayString
  alaQoSAppliedRuleAction DisplayString
  alaQoSAppliedRuleReflexive INTEGER
  alaQoSAppliedRuleSave INTEGER
  alaQoSAppliedRuleLog INTEGER
  alaQoSAppliedRuleMatches Counter32
  alaQoSAppliedRuleEnforced INTEGER
  alaQoSAppliedRuleActive INTEGER
  alaQoSAppliedRuleRowStatus RowStatus
  alaQoSAppliedRuleValidityPeriod DisplayString
  alaQoSAppliedRuleValidityPeriodStatus INTEGER
  alaQoSAppliedRuleLogInterval Integer32
  alaQoSAppliedRuleCountType INTEGER
  alaQoSAppliedRulePacketCount Counter64
  alaQoSAppliedRuleByteCount Counter64
  alaQoSAppliedRuleExcessPacketCount Counter64
  alaQoSAppliedRuleExcessByteCount Counter64
  alaQoSAppliedRuleType Integer32
  alaQoSAppliedRuleTrapEvents INTEGER
  alaQoSAppliedRuleDefaultList INTEGER
  alaQoSAppliedRuleGreenCount Counter64
  alaQoSAppliedRuleYellowCount Counter64
  alaQoSAppliedRuleRedCount Counter64
  alaQoSAppliedRuleNonGreenCount Counter64
  alaQoSAppliedRuleNonRedCount Counter64

QoSConditionEntry  
SEQUENCE    
  alaQoSConditionName DisplayString
  alaQoSConditionSource INTEGER
  alaQoSConditionSourceSlot Integer32
  alaQoSConditionSourceSlotStatus INTEGER
  alaQoSConditionSourcePort Integer32
  alaQoSConditionSourcePortGroup DisplayString
  alaQoSConditionSourcePortGroupStatus INTEGER
  alaQoSConditionDestinationSlot Integer32
  alaQoSConditionDestinationSlotStatus INTEGER
  alaQoSConditionDestinationPort Integer32
  alaQoSConditionDestinationPortGroup DisplayString
  alaQoSConditionDestinationPortGroupStatus INTEGER
  alaQoSConditionSourceInterfaceType INTEGER
  alaQoSConditionSourceInterfaceTypeStatus INTEGER
  alaQoSConditionDestinationInterfaceType INTEGER
  alaQoSConditionDestinationInterfaceTypeStatus INTEGER
  alaQoSConditionSourceMacAddr MacAddress
  alaQoSConditionSourceMacAddrStatus INTEGER
  alaQoSConditionSourceMacMask MacAddress
  alaQoSConditionSourceMacGroup DisplayString
  alaQoSConditionSourceMacGroupStatus INTEGER
  alaQoSConditionDestinationMacAddr MacAddress
  alaQoSConditionDestinationMacAddrStatus INTEGER
  alaQoSConditionDestinationMacMask MacAddress
  alaQoSConditionDestinationMacGroup DisplayString
  alaQoSConditionDestinationMacGroupStatus INTEGER
  alaQoSConditionSourceVlan Integer32
  alaQoSConditionSourceVlanStatus INTEGER
  alaQoSConditionDestinationVlan Integer32
  alaQoSConditionDestinationVlanStatus INTEGER
  alaQoSCondition8021p Integer32
  alaQoSCondition8021pStatus INTEGER
  alaQoSConditionSourceIpAddr IpAddress
  alaQoSConditionSourceIpAddrStatus INTEGER
  alaQoSConditionSourceIpMask IpAddress
  alaQoSConditionSourceNetworkGroup DisplayString
  alaQoSConditionSourceNetworkGroupStatus INTEGER
  alaQoSConditionDestinationIpAddr IpAddress
  alaQoSConditionDestinationIpAddrStatus INTEGER
  alaQoSConditionDestinationIpMask IpAddress
  alaQoSConditionDestinationNetworkGroup DisplayString
  alaQoSConditionDestinationNetworkGroupStatus INTEGER
  alaQoSConditionMulticastIpAddr IpAddress
  alaQoSConditionMulticastIpAddrStatus INTEGER
  alaQoSConditionMulticastIpMask IpAddress
  alaQoSConditionMulticastNetworkGroup DisplayString
  alaQoSConditionMulticastNetworkGroupStatus INTEGER
  alaQoSConditionTos Integer32
  alaQoSConditionTosStatus INTEGER
  alaQoSConditionTosMask Integer32
  alaQoSConditionDscp Integer32
  alaQoSConditionDscpStatus INTEGER
  alaQoSConditionDscpMask Integer32
  alaQoSConditionIpProtocol Integer32
  alaQoSConditionIpProtocolStatus INTEGER
  alaQoSConditionSourceIpPort Integer32
  alaQoSConditionSourceIpPortStatus INTEGER
  alaQoSConditionDestinationIpPort Integer32
  alaQoSConditionDestinationIpPortStatus INTEGER
  alaQoSConditionService DisplayString
  alaQoSConditionServiceStatus INTEGER
  alaQoSConditionServiceGroup DisplayString
  alaQoSConditionServiceGroupStatus INTEGER
  alaQoSConditionIcmpType Integer32
  alaQoSConditionIcmpTypeStatus INTEGER
  alaQoSConditionIcmpCode Integer32
  alaQoSConditionIcmpCodeStatus INTEGER
  alaQoSConditionDlci Integer32
  alaQoSConditionDlciStatus INTEGER
  alaQoSConditionRowStatus RowStatus
  alaQoSConditionSourcePortEnd Integer32
  alaQoSConditionDestinationPortEnd Integer32
  alaQoSConditionSourceIpPortEnd Integer32
  alaQoSConditionDestinationIpPortEnd Integer32
  alaQoSConditionSourceTcpPort Integer32
  alaQoSConditionSourceTcpPortStatus INTEGER
  alaQoSConditionSourceTcpPortEnd Integer32
  alaQoSConditionDestinationTcpPort Integer32
  alaQoSConditionDestinationTcpPortStatus INTEGER
  alaQoSConditionDestinationTcpPortEnd Integer32
  alaQoSConditionSourceUdpPort Integer32
  alaQoSConditionSourceUdpPortStatus INTEGER
  alaQoSConditionSourceUdpPortEnd Integer32
  alaQoSConditionDestinationUdpPort Integer32
  alaQoSConditionDestinationUdpPortStatus INTEGER
  alaQoSConditionDestinationUdpPortEnd Integer32
  alaQoSConditionEthertype Integer32
  alaQoSConditionEthertypeStatus INTEGER
  alaQoSConditionTcpFlags INTEGER
  alaQoSConditionTcpFlagsStatus INTEGER
  alaQoSConditionTcpFlagsVal Integer32
  alaQoSConditionTcpFlagsValStatus INTEGER
  alaQoSConditionTcpFlagsMask Integer32
  alaQoSConditionTcpFlagsMaskStatus INTEGER
  alaQoSConditionTcpEstablished INTEGER
  alaQoSConditionSourceIpv6Addr Ipv6Address
  alaQoSConditionSourceIpv6AddrStatus INTEGER
  alaQoSConditionSourceIpv6Mask Ipv6Address
  alaQoSConditionDestinationIpv6Addr Ipv6Address
  alaQoSConditionDestinationIpv6AddrStatus INTEGER
  alaQoSConditionDestinationIpv6Mask Ipv6Address
  alaQoSConditionIpv6Traffic INTEGER
  alaQoSConditionIpv6NH Integer32
  alaQoSConditionIpv6NHStatus INTEGER
  alaQoSConditionIpv6FlowLabel Integer32
  alaQoSConditionIpv6FlowLabelStatus INTEGER
  alaQoSConditionMcastIpv6Addr Ipv6Address
  alaQoSConditionMcastIpv6AddrStatus INTEGER
  alaQoSConditionMcastIpv6Mask Ipv6Address
  alaQoSConditionDscpEnd Integer32
  alaQoSConditionInnerSourceVlan Integer32
  alaQoSConditionInnerSourceVlanStatus INTEGER
  alaQoSConditionInner8021p Integer32
  alaQoSConditionInner8021pStatus INTEGER
  alaQoSConditionVrfName DisplayString
  alaQoSConditionVrfNameStatus INTEGER
  alaQoSCondition8021pEnd Integer32
  alaQoSConditionInner8021pEnd Integer32
  alaQoSConditionSourceVlanGroup DisplayString
  alaQoSConditionSourceVlanGroupStatus INTEGER
  alaQoSConditionInnerSourceVlanGroup DisplayString
  alaQoSConditionInnerSourceVlanGroupStatus INTEGER

QoSAppliedConditionEntry  
SEQUENCE    
  alaQoSAppliedConditionName DisplayString
  alaQoSAppliedConditionSource INTEGER
  alaQoSAppliedConditionSourceSlot Integer32
  alaQoSAppliedConditionSourceSlotStatus INTEGER
  alaQoSAppliedConditionSourcePort Integer32
  alaQoSAppliedConditionSourcePortGroup DisplayString
  alaQoSAppliedConditionSourcePortGroupStatus INTEGER
  alaQoSAppliedConditionDestinationSlot Integer32
  alaQoSAppliedConditionDestinationSlotStatus INTEGER
  alaQoSAppliedConditionDestinationPort Integer32
  alaQoSAppliedConditionDestinationPortGroup DisplayString
  alaQoSAppliedConditionDestinationPortGroupStatus INTEGER
  alaQoSAppliedConditionSourceInterfaceType INTEGER
  alaQoSAppliedConditionSourceInterfaceTypeStatus INTEGER
  alaQoSAppliedConditionDestinationInterfaceType INTEGER
  alaQoSAppliedConditionDestinationInterfaceTypeStatus INTEGER
  alaQoSAppliedConditionSourceMacAddr MacAddress
  alaQoSAppliedConditionSourceMacAddrStatus INTEGER
  alaQoSAppliedConditionSourceMacMask MacAddress
  alaQoSAppliedConditionSourceMacGroup DisplayString
  alaQoSAppliedConditionSourceMacGroupStatus INTEGER
  alaQoSAppliedConditionDestinationMacAddr MacAddress
  alaQoSAppliedConditionDestinationMacAddrStatus INTEGER
  alaQoSAppliedConditionDestinationMacMask MacAddress
  alaQoSAppliedConditionDestinationMacGroup DisplayString
  alaQoSAppliedConditionDestinationMacGroupStatus INTEGER
  alaQoSAppliedConditionSourceVlan Integer32
  alaQoSAppliedConditionSourceVlanStatus INTEGER
  alaQoSAppliedConditionDestinationVlan Integer32
  alaQoSAppliedConditionDestinationVlanStatus INTEGER
  alaQoSAppliedCondition8021p Integer32
  alaQoSAppliedCondition8021pStatus INTEGER
  alaQoSAppliedConditionSourceIpAddr IpAddress
  alaQoSAppliedConditionSourceIpAddrStatus INTEGER
  alaQoSAppliedConditionSourceIpMask IpAddress
  alaQoSAppliedConditionSourceNetworkGroup DisplayString
  alaQoSAppliedConditionSourceNetworkGroupStatus INTEGER
  alaQoSAppliedConditionDestinationIpAddr IpAddress
  alaQoSAppliedConditionDestinationIpAddrStatus INTEGER
  alaQoSAppliedConditionDestinationIpMask IpAddress
  alaQoSAppliedConditionDestinationNetworkGroup DisplayString
  alaQoSAppliedConditionDestinationNetworkGroupStatus INTEGER
  alaQoSAppliedConditionMulticastIpAddr IpAddress
  alaQoSAppliedConditionMulticastIpAddrStatus INTEGER
  alaQoSAppliedConditionMulticastIpMask IpAddress
  alaQoSAppliedConditionMulticastNetworkGroup DisplayString
  alaQoSAppliedConditionMulticastNetworkGroupStatus INTEGER
  alaQoSAppliedConditionTos Integer32
  alaQoSAppliedConditionTosStatus INTEGER
  alaQoSAppliedConditionTosMask Integer32
  alaQoSAppliedConditionDscp Integer32
  alaQoSAppliedConditionDscpStatus INTEGER
  alaQoSAppliedConditionDscpMask Integer32
  alaQoSAppliedConditionIpProtocol Integer32
  alaQoSAppliedConditionIpProtocolStatus INTEGER
  alaQoSAppliedConditionSourceIpPort Integer32
  alaQoSAppliedConditionSourceIpPortStatus INTEGER
  alaQoSAppliedConditionDestinationIpPort Integer32
  alaQoSAppliedConditionDestinationIpPortStatus INTEGER
  alaQoSAppliedConditionService DisplayString
  alaQoSAppliedConditionServiceStatus INTEGER
  alaQoSAppliedConditionServiceGroup DisplayString
  alaQoSAppliedConditionServiceGroupStatus INTEGER
  alaQoSAppliedConditionIcmpType Integer32
  alaQoSAppliedConditionIcmpTypeStatus INTEGER
  alaQoSAppliedConditionIcmpCode Integer32
  alaQoSAppliedConditionIcmpCodeStatus INTEGER
  alaQoSAppliedConditionDlci Integer32
  alaQoSAppliedConditionDlciStatus INTEGER
  alaQoSAppliedConditionRowStatus RowStatus
  alaQoSAppliedConditionSourcePortEnd Integer32
  alaQoSAppliedConditionDestinationPortEnd Integer32
  alaQoSAppliedConditionSourceIpPortEnd Integer32
  alaQoSAppliedConditionDestinationIpPortEnd Integer32
  alaQoSAppliedConditionSourceTcpPort Integer32
  alaQoSAppliedConditionSourceTcpPortStatus INTEGER
  alaQoSAppliedConditionSourceTcpPortEnd Integer32
  alaQoSAppliedConditionDestinationTcpPort Integer32
  alaQoSAppliedConditionDestinationTcpPortStatus INTEGER
  alaQoSAppliedConditionDestinationTcpPortEnd Integer32
  alaQoSAppliedConditionSourceUdpPort Integer32
  alaQoSAppliedConditionSourceUdpPortStatus INTEGER
  alaQoSAppliedConditionSourceUdpPortEnd Integer32
  alaQoSAppliedConditionDestinationUdpPort Integer32
  alaQoSAppliedConditionDestinationUdpPortStatus INTEGER
  alaQoSAppliedConditionDestinationUdpPortEnd Integer32
  alaQoSAppliedConditionEthertype Integer32
  alaQoSAppliedConditionEthertypeStatus INTEGER
  alaQoSAppliedConditionTcpFlags INTEGER
  alaQoSAppliedConditionTcpFlagsStatus INTEGER
  alaQoSAppliedConditionTcpFlagsVal Integer32
  alaQoSAppliedConditionTcpFlagsValStatus INTEGER
  alaQoSAppliedConditionTcpFlagsMask Integer32
  alaQoSAppliedConditionTcpFlagsMaskStatus INTEGER
  alaQoSAppliedConditionTcpEstablished INTEGER
  alaQoSAppliedConditionSourceIpv6Addr Ipv6Address
  alaQoSAppliedConditionSourceIpv6AddrStatus INTEGER
  alaQoSAppliedConditionSourceIpv6Mask Ipv6Address
  alaQoSAppliedConditionDestinationIpv6Addr Ipv6Address
  alaQoSAppliedConditionDestinationIpv6AddrStatus INTEGER
  alaQoSAppliedConditionDestinationIpv6Mask Ipv6Address
  alaQoSAppliedConditionIpv6Traffic INTEGER
  alaQoSAppliedConditionIpv6NH Integer32
  alaQoSAppliedConditionIpv6NHStatus INTEGER
  alaQoSAppliedConditionIpv6FlowLabel Integer32
  alaQoSAppliedConditionIpv6FlowLabelStatus INTEGER
  alaQoSAppliedConditionMcastIpv6Addr Ipv6Address
  alaQoSAppliedConditionMcastIpv6AddrStatus INTEGER
  alaQoSAppliedConditionMcastIpv6Mask Ipv6Address
  alaQoSAppliedConditionDscpEnd Integer32
  alaQoSAppliedConditionInnerSourceVlan Integer32
  alaQoSAppliedConditionInnerSourceVlanStatus INTEGER
  alaQoSAppliedConditionInner8021p Integer32
  alaQoSAppliedConditionInner8021pStatus INTEGER
  alaQoSAppliedConditionVrfName DisplayString
  alaQoSAppliedConditionVrfNameStatus INTEGER
  alaQoSAppliedCondition8021pEnd Integer32
  alaQoSAppliedConditionInner8021pEnd Integer32
  alaQoSAppliedConditionSourceVlanGroup DisplayString
  alaQoSAppliedConditionSourceVlanGroupStatus INTEGER
  alaQoSAppliedConditionInnerSourceVlanGroup DisplayString
  alaQoSAppliedConditionInnerSourceVlanGroupStatus INTEGER

QoSServiceEntry  
SEQUENCE    
  alaQoSServiceName DisplayString
  alaQoSServiceSource INTEGER
  alaQoSServiceProtocol Integer32
  alaQoSServiceSourceIpPort Integer32
  alaQoSServiceSourceIpPortStatus INTEGER
  alaQoSServiceDestinationIpPort Integer32
  alaQoSServiceDestinationIpPortStatus INTEGER
  alaQoSServiceRowStatus RowStatus
  alaQoSServiceSourceIpPortEnd Integer32
  alaQoSServiceDestinationIpPortEnd Integer32
  alaQoSServiceSourceTcpPort Integer32
  alaQoSServiceSourceTcpPortStatus INTEGER
  alaQoSServiceSourceTcpPortEnd Integer32
  alaQoSServiceDestinationTcpPort Integer32
  alaQoSServiceDestinationTcpPortStatus INTEGER
  alaQoSServiceDestinationTcpPortEnd Integer32
  alaQoSServiceSourceUdpPort Integer32
  alaQoSServiceSourceUdpPortStatus INTEGER
  alaQoSServiceSourceUdpPortEnd Integer32
  alaQoSServiceDestinationUdpPort Integer32
  alaQoSServiceDestinationUdpPortStatus INTEGER
  alaQoSServiceDestinationUdpPortEnd Integer32

QoSAppliedServiceEntry  
SEQUENCE    
  alaQoSAppliedServiceName DisplayString
  alaQoSAppliedServiceSource INTEGER
  alaQoSAppliedServiceProtocol Integer32
  alaQoSAppliedServiceSourceIpPort Integer32
  alaQoSAppliedServiceSourceIpPortStatus INTEGER
  alaQoSAppliedServiceDestinationIpPort Integer32
  alaQoSAppliedServiceDestinationIpPortStatus INTEGER
  alaQoSAppliedServiceRowStatus RowStatus
  alaQoSAppliedServiceSourceIpPortEnd Integer32
  alaQoSAppliedServiceDestinationIpPortEnd Integer32
  alaQoSAppliedServiceSourceTcpPort Integer32
  alaQoSAppliedServiceSourceTcpPortStatus INTEGER
  alaQoSAppliedServiceSourceTcpPortEnd Integer32
  alaQoSAppliedServiceDestinationTcpPort Integer32
  alaQoSAppliedServiceDestinationTcpPortStatus INTEGER
  alaQoSAppliedServiceDestinationTcpPortEnd Integer32
  alaQoSAppliedServiceSourceUdpPort Integer32
  alaQoSAppliedServiceSourceUdpPortStatus INTEGER
  alaQoSAppliedServiceSourceUdpPortEnd Integer32
  alaQoSAppliedServiceDestinationUdpPort Integer32
  alaQoSAppliedServiceDestinationUdpPortStatus INTEGER
  alaQoSAppliedServiceDestinationUdpPortEnd Integer32

QoSServiceGroupsEntry  
SEQUENCE    
  alaQoSServiceGroupsName DisplayString
  alaQoSServiceGroupsSource INTEGER
  alaQoSServiceGroupsStatus RowStatus

QoSAppliedServiceGroupsEntry  
SEQUENCE    
  alaQoSAppliedServiceGroupsName DisplayString
  alaQoSAppliedServiceGroupsSource INTEGER
  alaQoSAppliedServiceGroupsStatus RowStatus

QoSServiceGroupEntry  
SEQUENCE    
  alaQoSServiceGroupServiceName DisplayString
  alaQoSServiceGroupStatus RowStatus

QoSAppliedServiceGroupEntry  
SEQUENCE    
  alaQoSAppliedServiceGroupServiceName DisplayString
  alaQoSAppliedServiceGroupStatus RowStatus

QoSNetworkGroupsEntry  
SEQUENCE    
  alaQoSNetworkGroupsName DisplayString
  alaQoSNetworkGroupsSource INTEGER
  alaQoSNetworkGroupsStatus RowStatus

QoSAppliedNetworkGroupsEntry  
SEQUENCE    
  alaQoSAppliedNetworkGroupsName DisplayString
  alaQoSAppliedNetworkGroupsSource INTEGER
  alaQoSAppliedNetworkGroupsStatus RowStatus

QoSNetworkGroupEntry  
SEQUENCE    
  alaQoSNetworkGroupIpAddr IpAddress
  alaQoSNetworkGroupIpMask IpAddress
  alaQoSNetworkGroupStatus RowStatus

QoSAppliedNetworkGroupEntry  
SEQUENCE    
  alaQoSAppliedNetworkGroupIpAddr IpAddress
  alaQoSAppliedNetworkGroupIpMask IpAddress
  alaQoSAppliedNetworkGroupStatus RowStatus

QoSMACGroupsEntry  
SEQUENCE    
  alaQoSMACGroupsName DisplayString
  alaQoSMACGroupsSource INTEGER
  alaQoSMACGroupsStatus RowStatus

QoSAppliedMACGroupsEntry  
SEQUENCE    
  alaQoSAppliedMACGroupsName DisplayString
  alaQoSAppliedMACGroupsSource INTEGER
  alaQoSAppliedMACGroupsStatus RowStatus

QoSMACGroupEntry  
SEQUENCE    
  alaQoSMACGroupMacAddr MacAddress
  alaQoSMACGroupMacMask MacAddress
  alaQoSMACGroupStatus RowStatus

QoSAppliedMACGroupEntry  
SEQUENCE    
  alaQoSAppliedMACGroupMacAddr MacAddress
  alaQoSAppliedMACGroupMacMask MacAddress
  alaQoSAppliedMACGroupStatus RowStatus

QoSPortGroupsEntry  
SEQUENCE    
  alaQoSPortGroupsName DisplayString
  alaQoSPortGroupsSource INTEGER
  alaQoSPortGroupsStatus RowStatus

QoSAppliedPortGroupsEntry  
SEQUENCE    
  alaQoSAppliedPortGroupsName DisplayString
  alaQoSAppliedPortGroupsSource INTEGER
  alaQoSAppliedPortGroupsStatus RowStatus

QoSPortGroupEntry  
SEQUENCE    
  alaQoSPortGroupSlot Integer32
  alaQoSPortGroupPort Integer32
  alaQoSPortGroupStatus RowStatus
  alaQoSPortGroupPortEnd Integer32

QoSAppliedPortGroupEntry  
SEQUENCE    
  alaQoSAppliedPortGroupSlot Integer32
  alaQoSAppliedPortGroupPort Integer32
  alaQoSAppliedPortGroupStatus RowStatus
  alaQoSAppliedPortGroupPortEnd Integer32

QoSMapGroupsEntry  
SEQUENCE    
  alaQoSMapGroupsName DisplayString
  alaQoSMapGroupsSource INTEGER
  alaQoSMapGroupsStatus RowStatus

QoSAppliedMapGroupsEntry  
SEQUENCE    
  alaQoSAppliedMapGroupsName DisplayString
  alaQoSAppliedMapGroupsSource INTEGER
  alaQoSAppliedMapGroupsStatus RowStatus

QoSMapGroupEntry  
SEQUENCE    
  alaQoSMapGroupKey Integer32
  alaQoSMapGroupKeyEnd Integer32
  alaQoSMapGroupValue Integer32
  alaQoSMapGroupStatus RowStatus

QoSAppliedMapGroupEntry  
SEQUENCE    
  alaQoSAppliedMapGroupKey Integer32
  alaQoSAppliedMapGroupKeyEnd Integer32
  alaQoSAppliedMapGroupValue Integer32
  alaQoSAppliedMapGroupStatus RowStatus

QoSActionEntry  
SEQUENCE    
  alaQoSActionName DisplayString
  alaQoSActionSource INTEGER
  alaQoSActionDisposition INTEGER
  alaQoSActionDropAlgorithm INTEGER
  alaQoSActionWredMaximumThreshold Integer32
  alaQoSActionWredMaximumThresholdStatus INTEGER
  alaQoSActionWredMinimumThreshold Integer32
  alaQoSActionWredMinimumThresholdStatus INTEGER
  alaQoSActionWredMaximumProbability Integer32
  alaQoSActionWredMaximumProbabilityStatus INTEGER
  alaQoSActionMinimumBandwidth Integer32
  alaQoSActionMinimumBandwidthStatus INTEGER
  alaQoSActionMaximumBandwidth Integer32
  alaQoSActionMaximumBandwidthStatus INTEGER
  alaQoSActionPeakBandwidth Integer32
  alaQoSActionPeakBandwidthStatus INTEGER
  alaQoSActionPriority Integer32
  alaQoSActionPriorityStatus INTEGER
  alaQoSActionShared INTEGER
  alaQoSActionJitter Integer32
  alaQoSActionJitterStatus INTEGER
  alaQoSActionLatency Integer32
  alaQoSActionLatencyStatus INTEGER
  alaQoSActionMaximumDepth Integer32
  alaQoSActionMaximumDepthStatus INTEGER
  alaQoSActionMaximumBuffers Integer32
  alaQoSActionMaximumBuffersStatus INTEGER
  alaQoSAction8021p Integer32
  alaQoSAction8021pStatus INTEGER
  alaQoSActionTos Integer32
  alaQoSActionTosStatus INTEGER
  alaQoSActionDscp Integer32
  alaQoSActionDscpStatus INTEGER
  alaQoSActionMapFrom INTEGER
  alaQoSActionMapTo INTEGER
  alaQoSActionMapGroup DisplayString
  alaQoSActionMapGroupStatus INTEGER
  alaQoSActionSourceRewriteIpAddr IpAddress
  alaQoSActionSourceRewriteIpAddrStatus INTEGER
  alaQoSActionSourceRewriteIpMask IpAddress
  alaQoSActionSourceRewriteNetworkGroup DisplayString
  alaQoSActionSourceRewriteNetworkGroupStatus INTEGER
  alaQoSActionDestinationRewriteIpAddr IpAddress
  alaQoSActionDestinationRewriteIpAddrStatus INTEGER
  alaQoSActionDestinationRewriteIpMask IpAddress
  alaQoSActionDestinationRewriteNetworkGroup DisplayString
  alaQoSActionDestinationRewriteNetworkGroupStatus INTEGER
  alaQoSActionLoadBalanceGroup DisplayString
  alaQoSActionLoadBalanceGroupStatus INTEGER
  alaQoSActionPermanentGatewayIpAddr IpAddress
  alaQoSActionPermanentGatewayIpAddrStatus INTEGER
  alaQoSActionAlternateGatewayIpAddr IpAddress
  alaQoSActionAlternateGatewayIpAddrStatus INTEGER
  alaQoSActionRowStatus RowStatus
  alaQoSActionMinimumDepth Integer32
  alaQoSActionMinimumDepthStatus INTEGER
  alaQoSActionVPNAccess INTEGER
  alaQoSActionNocache INTEGER
  alaQoSActionPortdisable INTEGER
  alaQoSActionRedirectSlot Integer32
  alaQoSActionRedirectSlotStatus INTEGER
  alaQoSActionRedirectPort Integer32
  alaQoSActionRedirectAgg Integer32
  alaQoSActionRedirectAggStatus INTEGER
  alaQoSActionMirrorSlot Integer32
  alaQoSActionMirrorPort Integer32
  alaQoSActionMirrorMode INTEGER
  alaQoSActionMirrorModeStatus INTEGER
  alaQoSActionCIR Integer32
  alaQoSActionCIRStatus INTEGER
  alaQoSActionCBS Integer32
  alaQoSActionCBSStatus INTEGER
  alaQoSActionPIR Integer32
  alaQoSActionPIRStatus INTEGER
  alaQoSActionPBS Integer32
  alaQoSActionPBSStatus INTEGER
  alaQoSActionCounterColor INTEGER

QoSAppliedActionEntry  
SEQUENCE    
  alaQoSAppliedActionName DisplayString
  alaQoSAppliedActionSource INTEGER
  alaQoSAppliedActionDisposition INTEGER
  alaQoSAppliedActionDropAlgorithm INTEGER
  alaQoSAppliedActionWredMaximumThreshold Integer32
  alaQoSAppliedActionWredMaximumThresholdStatus INTEGER
  alaQoSAppliedActionWredMinimumThreshold Integer32
  alaQoSAppliedActionWredMinimumThresholdStatus INTEGER
  alaQoSAppliedActionWredMaximumProbability Integer32
  alaQoSAppliedActionWredMaximumProbabilityStatus INTEGER
  alaQoSAppliedActionMinimumBandwidth Integer32
  alaQoSAppliedActionMinimumBandwidthStatus INTEGER
  alaQoSAppliedActionMaximumBandwidth Integer32
  alaQoSAppliedActionMaximumBandwidthStatus INTEGER
  alaQoSAppliedActionPeakBandwidth Integer32
  alaQoSAppliedActionPeakBandwidthStatus INTEGER
  alaQoSAppliedActionPriority Integer32
  alaQoSAppliedActionPriorityStatus INTEGER
  alaQoSAppliedActionShared INTEGER
  alaQoSAppliedActionJitter Integer32
  alaQoSAppliedActionJitterStatus INTEGER
  alaQoSAppliedActionLatency Integer32
  alaQoSAppliedActionLatencyStatus INTEGER
  alaQoSAppliedActionMaximumDepth Integer32
  alaQoSAppliedActionMaximumDepthStatus INTEGER
  alaQoSAppliedActionMaximumBuffers Integer32
  alaQoSAppliedActionMaximumBuffersStatus INTEGER
  alaQoSAppliedAction8021p Integer32
  alaQoSAppliedAction8021pStatus INTEGER
  alaQoSAppliedActionTos Integer32
  alaQoSAppliedActionTosStatus INTEGER
  alaQoSAppliedActionDscp Integer32
  alaQoSAppliedActionDscpStatus INTEGER
  alaQoSAppliedActionMapFrom INTEGER
  alaQoSAppliedActionMapTo INTEGER
  alaQoSAppliedActionMapGroup DisplayString
  alaQoSAppliedActionMapGroupStatus INTEGER
  alaQoSAppliedActionSourceRewriteIpAddr IpAddress
  alaQoSAppliedActionSourceRewriteIpAddrStatus INTEGER
  alaQoSAppliedActionSourceRewriteIpMask IpAddress
  alaQoSAppliedActionSourceRewriteNetworkGroup DisplayString
  alaQoSAppliedActionSourceRewriteNetworkGroupStatus INTEGER
  alaQoSAppliedActionDestinationRewriteIpAddr IpAddress
  alaQoSAppliedActionDestinationRewriteIpAddrStatus INTEGER
  alaQoSAppliedActionDestinationRewriteIpMask IpAddress
  alaQoSAppliedActionDestinationRewriteNetworkGroup DisplayString
  alaQoSAppliedActionDestinationRewriteNetworkGroupStatus INTEGER
  alaQoSAppliedActionLoadBalanceGroup DisplayString
  alaQoSAppliedActionLoadBalanceGroupStatus INTEGER
  alaQoSAppliedActionPermanentGatewayIpAddr IpAddress
  alaQoSAppliedActionPermanentGatewayIpAddrStatus INTEGER
  alaQoSAppliedActionAlternateGatewayIpAddr IpAddress
  alaQoSAppliedActionAlternateGatewayIpAddrStatus INTEGER
  alaQoSAppliedActionRowStatus RowStatus
  alaQoSAppliedActionMinimumDepth Integer32
  alaQoSAppliedActionMinimumDepthStatus INTEGER
  alaQoSAppliedActionVPNAccess INTEGER
  alaQoSAppliedActionNocache INTEGER
  alaQoSAppliedActionPortdisable INTEGER
  alaQoSAppliedActionRedirectSlot Integer32
  alaQoSAppliedActionRedirectSlotStatus INTEGER
  alaQoSAppliedActionRedirectPort Integer32
  alaQoSAppliedActionRedirectAgg Integer32
  alaQoSAppliedActionRedirectAggStatus INTEGER
  alaQoSAppliedActionMirrorSlot Integer32
  alaQoSAppliedActionMirrorPort Integer32
  alaQoSAppliedActionMirrorMode INTEGER
  alaQoSAppliedActionMirrorModeStatus INTEGER
  alaQoSAppliedActionCIR Integer32
  alaQoSAppliedActionCIRStatus INTEGER
  alaQoSAppliedActionCBS Integer32
  alaQoSAppliedActionCBSStatus INTEGER
  alaQoSAppliedActionPIR Integer32
  alaQoSAppliedActionPIRStatus INTEGER
  alaQoSAppliedActionPBS Integer32
  alaQoSAppliedActionPBSStatus INTEGER
  alaQoSAppliedActionCounterColor INTEGER

QoSPortEntry  
SEQUENCE    
  alaQoSPortSlot Integer32
  alaQoSPortPort Integer32
  alaQoSPortEnabled INTEGER
  alaQoSPortAppliedEnabled INTEGER
  alaQoSPortInterfaceType INTEGER
  alaQoSPortTrusted INTEGER
  alaQoSPortDefault8021p Integer32
  alaQoSPortDefaultDSCP Integer32
  alaQoSPortMaximumReservedBandwidth Integer32
  alaQoSPortMaximumReservedBandwidthStatus INTEGER
  alaQoSPortAppliedMaximumReservedBandwidth Integer32
  alaQoSPortAppliedMaximumReservedBandwidthStatus INTEGER
  alaQoSPortMaximumSignalledBandwidth Integer32
  alaQoSPortMaximumSignalledBandwidthStatus INTEGER
  alaQoSPortAppliedMaximumSignalledBandwidth Integer32
  alaQoSPortAppliedMaximumSignalledBandwidthStatus INTEGER
  alaQoSPortDefaultQueues Integer32
  alaQoSPortAppliedDefaultQueues Integer32
  alaQoSPortMaximumDefaultBandwidth Integer32
  alaQoSPortMaximumDefaultBandwidthStatus INTEGER
  alaQoSPortAppliedMaximumDefaultBandwidth Integer32
  alaQoSPortAppliedMaximumDefaultBandwidthStatus INTEGER
  alaQoSPortMaximumDefaultDepth Integer32
  alaQoSPortMaximumDefaultDepthStatus INTEGER
  alaQoSPortAppliedMaximumDefaultDepth Integer32
  alaQoSPortAppliedMaximumDefaultDepthStatus INTEGER
  alaQoSPortMaximumDefaultBuffers Integer32
  alaQoSPortMaximumDefaultBuffersStatus INTEGER
  alaQoSPortAppliedMaximumDefaultBuffers Integer32
  alaQoSPortAppliedMaximumDefaultBuffersStatus INTEGER
  alaQoSPortReset INTEGER
  alaQoSPortPhysicalBandwidth Integer32
  alaQoSPortReservedBandwidth Integer32
  alaQoSPortSignalledBandwidth Integer32
  alaQoSPortCurrentBandwidth Integer32
  alaQoSPortDefaultQidLow Integer32
  alaQoSPortDefaultQidMedium Integer32
  alaQoSPortDefaultQidHigh Integer32
  alaQoSPortDefaultQidUrgent Integer32
  alaQoSPortFloodQid Integer32
  alaQoSPortQueues Integer32
  alaQoSPortQueuesCreated Integer32
  alaQoSPortQueuesFailed Integer32
  alaQoSPortQueuesPreempted Integer32
  alaQoSPortRowStatus RowStatus
  alaQoSPortFirPrio0EnqBytes Counter64
  alaQoSPortFirPrio0DeqBytes Counter64
  alaQoSPortFirPrio0EnqPkts Counter64
  alaQoSPortFirPrio0DeqPkts Counter64
  alaQoSPortFirPrio0QidDiscardPkts Counter64
  alaQoSPortFirPrio0WredDiscardPkts Counter64
  alaQoSPortFirPrio0OverflowDiscardPkts Counter64
  alaQoSPortFirPrio1EnqBytes Counter64
  alaQoSPortFirPrio1DeqBytes Counter64
  alaQoSPortFirPrio1EnqPkts Counter64
  alaQoSPortFirPrio1DeqPkts Counter64
  alaQoSPortFirPrio1QidDiscardPkts Counter64
  alaQoSPortFirPrio1WredDiscardPkts Counter64
  alaQoSPortFirPrio1OverflowDiscardPkts Counter64
  alaQoSPortFirPrio2EnqBytes Counter64
  alaQoSPortFirPrio2DeqBytes Counter64
  alaQoSPortFirPrio2EnqPkts Counter64
  alaQoSPortFirPrio2DeqPkts Counter64
  alaQoSPortFirPrio2QidDiscardPkts Counter64
  alaQoSPortFirPrio2WredDiscardPkts Counter64
  alaQoSPortFirPrio2OverflowDiscardPkts Counter64
  alaQoSPortFirPrio3EnqBytes Counter64
  alaQoSPortFirPrio3DeqBytes Counter64
  alaQoSPortFirPrio3EnqPkts Counter64
  alaQoSPortFirPrio3DeqPkts Counter64
  alaQoSPortFirPrio3QidDiscardPkts Counter64
  alaQoSPortFirPrio3WredDiscardPkts Counter64
  alaQoSPortFirPrio3OverflowDiscardPkts Counter64
  alaQoSPortDefaultClassification INTEGER
  alaQoSPortLowPriorityWeight Integer32
  alaQoSPortMediumPriorityWeight Integer32
  alaQoSPortHighPriorityWeight Integer32
  alaQoSPortUrgentPriorityWeight Integer32
  alaQoSPortMaximumBandwidth Integer32
  alaQoSPortMaximumBandwidthStatus INTEGER
  alaQoSPortEnqueuingThresholdP0Lower Integer32
  alaQoSPortEnqueuingThresholdP0Upper Integer32
  alaQoSPortEnqueuingThresholdP1Lower Integer32
  alaQoSPortEnqueuingThresholdP1Upper Integer32
  alaQoSPortEnqueuingThresholdP2Lower Integer32
  alaQoSPortEnqueuingThresholdP2Upper Integer32
  alaQoSPortEnqueuingThresholdP3Lower Integer32
  alaQoSPortEnqueuingThresholdP3Upper Integer32
  alaQoSPortEnqueuingThresholdStatus INTEGER
  alaQoSPortServicingMode INTEGER
  alaQoSPortHighDensity INTEGER
  alaQoSPortFreeFFPRules Integer32
  alaQoSPortUsedFFPRules Integer32
  alaQoSPortFreeFFPMasks Integer32
  alaQoSPortUsedFFPMasks Integer32
  alaQoSPortSpoofedCount Integer32
  alaQoSPortNonSpoofedCount Integer32
  alaQoSPortQ4PriorityWeight Integer32
  alaQoSPortQ5PriorityWeight Integer32
  alaQoSPortQ6PriorityWeight Integer32
  alaQoSPortQ7PriorityWeight Integer32
  alaQoSPortCOS0MaximumBandwidth Integer32
  alaQoSPortCOS0MaximumBandwidthStatus INTEGER
  alaQoSPortCOS1MaximumBandwidth Integer32
  alaQoSPortCOS1MaximumBandwidthStatus INTEGER
  alaQoSPortCOS2MaximumBandwidth Integer32
  alaQoSPortCOS2MaximumBandwidthStatus INTEGER
  alaQoSPortCOS3MaximumBandwidth Integer32
  alaQoSPortCOS3MaximumBandwidthStatus INTEGER
  alaQoSPortCOS4MaximumBandwidth Integer32
  alaQoSPortCOS4MaximumBandwidthStatus INTEGER
  alaQoSPortCOS5MaximumBandwidth Integer32
  alaQoSPortCOS5MaximumBandwidthStatus INTEGER
  alaQoSPortCOS6MaximumBandwidth Integer32
  alaQoSPortCOS6MaximumBandwidthStatus INTEGER
  alaQoSPortCOS7MaximumBandwidth Integer32
  alaQoSPortCOS7MaximumBandwidthStatus INTEGER
  alaQoSPortCOS0MinimumBandwidth Integer32
  alaQoSPortCOS0MinimumBandwidthStatus INTEGER
  alaQoSPortCOS1MinimumBandwidth Integer32
  alaQoSPortCOS1MinimumBandwidthStatus INTEGER
  alaQoSPortCOS2MinimumBandwidth Integer32
  alaQoSPortCOS2MinimumBandwidthStatus INTEGER
  alaQoSPortCOS3MinimumBandwidth Integer32
  alaQoSPortCOS3MinimumBandwidthStatus INTEGER
  alaQoSPortCOS4MinimumBandwidth Integer32
  alaQoSPortCOS4MinimumBandwidthStatus INTEGER
  alaQoSPortCOS5MinimumBandwidth Integer32
  alaQoSPortCOS5MinimumBandwidthStatus INTEGER
  alaQoSPortCOS6MinimumBandwidth Integer32
  alaQoSPortCOS6MinimumBandwidthStatus INTEGER
  alaQoSPortCOS7MinimumBandwidth Integer32
  alaQoSPortCOS7MinimumBandwidthStatus INTEGER
  alaQoSPortMaximumIngBandwidth Integer32
  alaQoSPortMaximumIngBandwidthStatus INTEGER
  alaQoSPortDEIMarking INTEGER
  alaQoSPortMonitor INTEGER
  alaQoSPortDEIMapping INTEGER

QoSQueueEntry  
SEQUENCE    
  alaQoSQueueId Integer32
  alaQoSQueueSlot Integer32
  alaQoSQueuePort Integer32
  alaQoSQueuePortId Integer32
  alaQoSQueueType INTEGER
  alaQoSQueuePriority Integer32
  alaQoSQueueMinimumBandwidth Integer32
  alaQoSQueueMaximumBandwidth Integer32
  alaQoSQueueAverageBandwidth Integer32
  alaQoSQueueMinimumDepth Integer32
  alaQoSQueueMaximumDepth Integer32
  alaQoSQueueMaximumBuffers Integer32
  alaQoSQueue8021p Integer32
  alaQoSQueuePacketsSent Integer32
  alaQoSQueuePacketsDropped Integer32
  alaQoSQueueMaxLength Integer32
  alaQoSQueueAverageLength Integer32
  alaQoSQueueCurrentLength Integer32
  alaQoSQueueAction DisplayString

QoSSlotEntry  
SEQUENCE    
  alaQoSSlotSlot Integer32
  alaQoSSlotSlice Integer32
  alaQoSSlotType INTEGER
  alaQoSSlotMaxBuffers Integer32
  alaQoSSlotFreeBuffers1 Integer32
  alaQoSSlotFreeBuffers2 Integer32
  alaQoSSlotThreshold1Low Integer32
  alaQoSSlotThreshold1Medium Integer32
  alaQoSSlotThreshold1High Integer32
  alaQoSSlotThreshold1Urgent Integer32
  alaQoSSlotThreshold2Low Integer32
  alaQoSSlotThreshold2Medium Integer32
  alaQoSSlotThreshold2High Integer32
  alaQoSSlotThreshold2Urgent Integer32
  alaQoSSlotBuffersDenied Integer32
  alaQoSSlotBuffersDeniedAverage Integer32
  alaQoSSlotBuffersDropped Integer32
  alaQoSSlotBuffersDroppedAverage Integer32
  alaQoSSlotWredThresholdP0Lower Integer32
  alaQoSSlotWredThresholdP0Upper Integer32
  alaQoSSlotWredThresholdP1Lower Integer32
  alaQoSSlotWredThresholdP1Upper Integer32
  alaQoSSlotWredThresholdP2Lower Integer32
  alaQoSSlotWredThresholdP2Upper Integer32
  alaQoSSlotWredThresholdP3Lower Integer32
  alaQoSSlotWredThresholdP3Upper Integer32
  alaQoSSlotWredAverageCounterWeight Integer32
  alaQoSSlotWredThresholdStatus INTEGER
  alaQoSSlotCbqThresholdMode INTEGER
  alaQoSSlotCbqThresholdP1 Integer32
  alaQoSSlotCbqThresholdP2 Integer32
  alaQoSSlotCbqThresholdP3 Integer32
  alaQoSSlotHighDensity INTEGER

QoSSlotProtocolEntry  
SEQUENCE    
  alaQoSSlotProtocolId INTEGER
  alaQoSSlotProtocolEthertype Integer32
  alaQoSSlotProtocolDsap Integer32
  alaQoSSlotProtocolSsap Integer32
  alaQoSSlotProtocol8023Enabled INTEGER
  alaQoSSlotProtocolType INTEGER
  alaQoSSlotProtocolRowStatus RowStatus

QoSPortProtocolEntry  
SEQUENCE    
  alaQoSPortProtocolId INTEGER
  alaQoSPortProtocolClassification INTEGER
  alaQoSPortProtocolPriorityP0 Integer32
  alaQoSPortProtocolPriorityP1 Integer32
  alaQoSPortProtocolPriorityP2 Integer32
  alaQoSPortProtocolPriorityP3 Integer32
  alaQoSPortProtocolPriorityP4 Integer32
  alaQoSPortProtocolPriorityP5 Integer32
  alaQoSPortProtocolPriorityP6 Integer32
  alaQoSPortProtocolPriorityP7 Integer32
  alaQoSPortProtocolRowStatus RowStatus

QoSSlotDscpEntry  
SEQUENCE    
  alaQoSSlotDscpIndex Integer32
  alaQoSSlotDscpPriority Integer32

QoSSlotPcamEntry  
SEQUENCE    
  alaQoSSlotPcamId Integer32
  alaQoSSlotPcamEthertype Integer32
  alaQoSSlotPcamDsap Integer32
  alaQoSSlotPcamSsap Integer32
  alaQoSSlotPcam8023Enabled INTEGER
  alaQoSSlotPcamProtocolNumber Integer32
  alaQoSSlotPcamEnableEntry INTEGER
  alaQoSSlotPcamEnable8023 INTEGER
  alaQoSSlotPcamEnableDsap INTEGER
  alaQoSSlotPcamEnableSsap INTEGER
  alaQoSSlotPcamEnableEthertype INTEGER

QoSPortPdiEntry  
SEQUENCE    
  alaQoSPortPdiId Integer32
  alaQoSPortPdiPriorityType Integer32
  alaQoSPortPdiPriorityP0 Integer32
  alaQoSPortPdiPriorityP1 Integer32
  alaQoSPortPdiPriorityP2 Integer32
  alaQoSPortPdiPriorityP3 Integer32
  alaQoSPortPdiPriorityP4 Integer32
  alaQoSPortPdiPriorityP5 Integer32
  alaQoSPortPdiPriorityP6 Integer32
  alaQoSPortPdiPriorityP7 Integer32

QoSValidityPeriodEntry  
SEQUENCE    
  alaQoSValidityPeriodName DisplayString
  alaQoSValidityPeriodSource INTEGER
  alaQoSValidityPeriodDays Integer32
  alaQoSValidityPeriodDaysStatus INTEGER
  alaQoSValidityPeriodMonths Integer32
  alaQoSValidityPeriodMonthsStatus INTEGER
  alaQoSValidityPeriodHour DisplayString
  alaQoSValidityPeriodHourStatus INTEGER
  alaQoSValidityPeriodEndHour DisplayString
  alaQoSValidityPeriodInterval DisplayString
  alaQoSValidityPeriodIntervalStatus INTEGER
  alaQoSValidityPeriodEndInterval DisplayString
  alaQoSValidityPeriodRowStatus RowStatus

QoSAppliedValidityPeriodEntry  
SEQUENCE    
  alaQoSAppliedValidityPeriodName DisplayString
  alaQoSAppliedValidityPeriodSource INTEGER
  alaQoSAppliedValidityPeriodDays Integer32
  alaQoSAppliedValidityPeriodDaysStatus INTEGER
  alaQoSAppliedValidityPeriodMonths Integer32
  alaQoSAppliedValidityPeriodMonthsStatus INTEGER
  alaQoSAppliedValidityPeriodHour DisplayString
  alaQoSAppliedValidityPeriodHourStatus INTEGER
  alaQoSAppliedValidityPeriodEndHour DisplayString
  alaQoSAppliedValidityPeriodInterval DisplayString
  alaQoSAppliedValidityPeriodIntervalStatus INTEGER
  alaQoSAppliedValidityPeriodEndInterval DisplayString
  alaQoSAppliedValidityPeriodRowStatus RowStatus

QoSImportEntry  
SEQUENCE    
  alaQoSImportIndex Integer32
  alaQoSImportText DisplayString
  alaQoSImportPrecedence Integer32
  alaQoSImportPrefix DisplayString
  alaQoSImportSlot Integer32
  alaQoSImportPort Integer32
  alaQoSImportPortend Integer32
  alaQoSImportPortgroup DisplayString
  alaQoSImportRowStatus RowStatus

QoSAppliedImportEntry  
SEQUENCE    
  alaQoSAppliedImportIndex Integer32
  alaQoSAppliedImportText DisplayString
  alaQoSAppliedImportPrecedence Integer32
  alaQoSAppliedImportPrefix DisplayString
  alaQoSAppliedImportSlot Integer32
  alaQoSAppliedImportPort Integer32
  alaQoSAppliedImportPortend Integer32
  alaQoSAppliedImportPortgroup DisplayString
  alaQoSAppliedImportRowStatus RowStatus

QoSRuleGroupsEntry  
SEQUENCE    
  alaQoSRuleGroupsName DisplayString
  alaQoSRuleGroupsSource INTEGER
  alaQoSRuleGroupsType INTEGER
  alaQoSRuleGroupsEnabled INTEGER
  alaQoSRuleGroupsStatus RowStatus

QoSAppliedRuleGroupsEntry  
SEQUENCE    
  alaQoSAppliedRuleGroupsName DisplayString
  alaQoSAppliedRuleGroupsSource INTEGER
  alaQoSAppliedRuleGroupsType INTEGER
  alaQoSAppliedRuleGroupsEnabled INTEGER
  alaQoSAppliedRuleGroupsStatus RowStatus

QoSRuleGroupEntry  
SEQUENCE    
  alaQoSRuleGroupRuleName DisplayString
  alaQoSRuleGroupMatches Counter32
  alaQoSRuleGroupCountType INTEGER
  alaQoSRuleGroupPacketCount Counter64
  alaQoSRuleGroupByteCount Counter64
  alaQoSRuleGroupStatus RowStatus

QoSAppliedRuleGroupEntry  
SEQUENCE    
  alaQoSAppliedRuleGroupRuleName DisplayString
  alaQoSAppliedRuleGroupMatches Counter32
  alaQoSAppliedRuleGroupCountType INTEGER
  alaQoSAppliedRuleGroupPacketCount Counter64
  alaQoSAppliedRuleGroupByteCount Counter64
  alaQoSAppliedRuleGroupStatus RowStatus

QoSVlanGroupsEntry  
SEQUENCE    
  alaQoSVlanGroupsName DisplayString
  alaQoSVlanGroupsSource INTEGER
  alaQoSVlanGroupsStatus RowStatus

QoSAppliedVlanGroupsEntry  
SEQUENCE    
  alaQoSAppliedVlanGroupsName DisplayString
  alaQoSAppliedVlanGroupsSource INTEGER
  alaQoSAppliedVlanGroupsStatus RowStatus

QoSVlanGroupEntry  
SEQUENCE    
  alaQoSVlanGroupVlan Integer32
  alaQoSVlanGroupVlanEnd Integer32
  alaQoSVlanGroupStatus RowStatus

QoSAppliedVlanGroupEntry  
SEQUENCE    
  alaQoSAppliedVlanGroupVlan Integer32
  alaQoSAppliedVlanGroupVlanEnd Integer32
  alaQoSAppliedVlanGroupStatus RowStatus

QoSHwLoopbackProfileEntry  
SEQUENCE    
  alaQoSHwLoopbackProfileName DisplayString
  alaQoSHwLoopbackSourceMac MacAddress
  alaQoSHwLoopbackDestinationMac MacAddress
  alaQoSHwLoopbackVlan Integer32
  alaQoSHwLoopbackPort InterfaceIndex
  alaQoSHwLoopbackType INTEGER
  alaQoSHwLoopbackProfileStatus INTEGER
  alaQoSHwLoopbackProfileRowStatus RowStatus

Defined Values

alaQoSMIB 1.3.6.1.4.1.6486.801.1.2.1.22.1
QoS and Filtering MIB
MODULE-IDENTITY    

alaQoSMIBObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.1
Branch for QoS Managed Objects.
Status: current Access: read-write
OBJECT-IDENTITY    

alaQoSRuleTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1
Table of QoS Rule definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSRuleEntry

alaQoSRuleEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1
Definition of QoS Rule
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSRuleEntry  

alaQoSRuleName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.1
Name of rule
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSRuleEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.2
Is this rule enabled or not
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSRuleSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.3
What entity created the rule.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSRulePrecedence 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.4
Precedence value for rule. Rules are evaluated from higher precedence to lower. If rules have equal precedence, they are evaluated in the order they are received.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSRuleCondition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.5
Name of the condition to use
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSRuleAction 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.6
Name of the action to use
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSRuleReflexive 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.7
Indicator to tell if the rule is reflexive. Reflexive rules allow specific return connections that would normally be denied.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleSave 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.8
Indicator to tell whether to write out the rule during snapshot commands.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleLog 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.9
Indicator to tell whether to log matches to this rule in the QoS log.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.10
Number of times this rule has been matched.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSRuleEnforced 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.11
Is this rule currenly being enforced on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleActive 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.12
Is this rule enforcable by the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.13
Used to create/delete rules according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSRuleValidityPeriod 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.14
Name of the validity period to use
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSRuleValidityPeriodStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.15
Status field indicating whether there is a validity period associated with this rule
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSRuleLogInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.16
How often to look for packets matching this rule when logging. When 0 log as many as possible.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3600  

alaQoSRuleCountType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.17
Which rule statistics counters to update if not all are available
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER packets(1), bytes(2)  

alaQoSRulePacketCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.18
Counter for packets patching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleByteCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.19
Counter for bytes matching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleExcessPacketCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.20
Counter for packets out of bandwidth parameters
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleExcessByteCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.21
Counter for bytes out of bandwidth parameters
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.22
The type of rule this is. Each bit represents the following: 0x1 = bridged 0x2 = routed 0x4 = multicast
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSRuleTrapEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.23
Send SNMP trap when 'qos user-port shutdown' param or rule having action=port-disable is matched/invoked?
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleDefaultList 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.24
This rule belongs to the default policy list.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSRuleGreenCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.25
Counter for the number of packets being green compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleYellowCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.26
Counter for the number of packets being yellow compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleRedCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.27
Counter for the number of packets being red compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleNonGreenCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.28
Counter for the number of packets being non-green compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleNonRedCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.1.1.29
Counter for the number of packets being non-red compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2
Table of QoS AppliedRule definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedRuleEntry

alaQoSAppliedRuleEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1
Definition of QoS AppliedRule
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedRuleEntry  

alaQoSAppliedRuleName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.1
Name of rule
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedRuleEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.2
Is this rule enabled or not
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSAppliedRuleSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.3
What entity created the rule.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedRulePrecedence 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.4
Precedence value for rule. Rules are evaluated from higher precedence to lower. If rules have equal precedence, they are evaluated in the order they are received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedRuleCondition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.5
Name of the condition to use
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedRuleAction 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.6
Name of the action to use
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedRuleReflexive 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.7
Indicator to tell if the rule is reflexive. Reflexive rules allow specific return connections that would normally be denied.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleSave 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.8
Indicator to tell whether to write out the rule during snapshot commands.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleLog 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.9
Indicator to tell whether to log matches to this rule in the QoS log.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.10
Number of times this rule has been matched.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSAppliedRuleEnforced 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.11
Is this rule currenly being enforced on the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleActive 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.12
Is this rule enforcable by the switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.13
Used to create/delete rules according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedRuleValidityPeriod 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.14
Name of the validity period to use
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedRuleValidityPeriodStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.15
Status field indicating whether there is a validity period associated with this rule
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedRuleLogInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.16
How often to look for packets matching this rule when logging. When 0 log as many as possible.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..3600  

alaQoSAppliedRuleCountType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.17
Which rule statistics counters to update if not all are available
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER packets(1), bytes(2)  

alaQoSAppliedRulePacketCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.18
Counter for packets patching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleByteCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.19
Counter for bytes matching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleExcessPacketCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.20
Counter for packets out of bandwidth parameters
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleExcessByteCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.21
Counter for bytes out of bandwidth parameters
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.22
The type of rule this is. Each bit represents the following: 0x1 = bridged 0x2 = routed 0x4 = multicast
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedRuleTrapEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.23
Send SNMP trap when 'qos user-port shutdown' param or rule having action=port-disable is matched/invoked?
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleDefaultList 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.24
This rule belongs to the default policy list.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedRuleGreenCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.25
Counter for the number of packets being green compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleYellowCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.26
Counter for the number of packets being yellow compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleRedCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.27
Counter for the number of packets being red compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleNonGreenCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.28
Counter for the number of packets being non-green compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleNonRedCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.2.1.29
Counter for the number of packets being non-red compliant.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSConditionTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3
Table of QoS Condition definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSConditionEntry

alaQoSConditionEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1
Definition of QoS Condition
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSConditionEntry  

alaQoSConditionName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.1
Name of condition
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.2
What entity created the condition.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSConditionSourceSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.3
Source physical slot used for traffic classification When 0, the port identifies an aggregate
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

alaQoSConditionSourceSlotStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.4
Status field indicating whether the source physical slot and port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourcePort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.5
Source physical port range start to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..52  

alaQoSConditionSourcePortGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.6
Source physical port group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionSourcePortGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.7
Status field indicating whether the source physical port group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.8
Destination physical slot used for traffic classification When 0, the port identifies an aggregate
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

alaQoSConditionDestinationSlotStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.9
Status field indicating whether the destination physical slot and port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.10
Destination physical port range start to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..52  

alaQoSConditionDestinationPortGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.11
Destination physical port group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionDestinationPortGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.12
Status field indicating whether the destination physical port group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.13
Source physical interface type to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSConditionSourceInterfaceTypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.14
Status field indicating whether the source physical interface type needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.15
Destination physical interface type to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSConditionDestinationInterfaceTypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.16
Status field indicating whether the destination physical interface type needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceMacAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.17
Source MAC address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

alaQoSConditionSourceMacAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.18
Status field indicating whether the source MAC address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceMacMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.19
Source MAC mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

alaQoSConditionSourceMacGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.20
Source MAC group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionSourceMacGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.21
Status field indicating whether the source MAC group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationMacAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.22
Destination MAC address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

alaQoSConditionDestinationMacAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.23
Status field indicating whether the destination MAC address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationMacMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.24
Destination MAC mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

alaQoSConditionDestinationMacGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.25
Destination MAC group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionDestinationMacGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.26
Status field indicating whether the destination MAC group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.27
Source VLAN to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSConditionSourceVlanStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.28
Status field indicating whether the source VLAN needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.29
Destination VLAN to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSConditionDestinationVlanStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.30
Status field indicating whether the destination VLAN needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSCondition8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.31
802.1p value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSCondition8021pStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.32
Status field indicating whether the 802.1p value needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.33
Source IP address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSConditionSourceIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.34
Status field indicating whether the source IP address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.35
Source IP mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSConditionSourceNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.36
Source network group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionSourceNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.37
Status field indicating whether the source network group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.38
Destination IP address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSConditionDestinationIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.39
Status field indicating whether the destination IP address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.40
Destination IP mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSConditionDestinationNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.41
Destination network group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionDestinationNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.42
Status field indicating whether the destination network group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionMulticastIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.43
Multicast IP address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSConditionMulticastIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.44
Status field indicating whether the multicast IP address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionMulticastIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.45
Multicast IP mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSConditionMulticastNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.46
Multicast network group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionMulticastNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.47
Status field indicating whether the multicast network group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionTos 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.48
TOS value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSConditionTosStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.49
Status field indicating whether the TOS value & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionTosMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.50
TOS mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSConditionDscp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.51
DSCP value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

alaQoSConditionDscpStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.52
Status field indicating whether the DSCP value & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDscpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.53
DSCP mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

alaQoSConditionIpProtocol 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.54
IP protocol to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSConditionIpProtocolStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.55
Status field indicating whether the IP protocol needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.56
Source IP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionSourceIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.57
Status field indicating whether the source IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.58
Destination IP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionDestinationIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.59
Status field indicating whether the destination IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionService 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.60
Name of service to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionServiceStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.61
Status field indicating whether the service needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionServiceGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.62
Name of service group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionServiceGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.63
Status field indicating whether the service group needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionIcmpType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.64
ICMP type to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSConditionIcmpTypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.65
Status field indicating whether the ICMP type needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionIcmpCode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.66
ICMP code to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSConditionIcmpCodeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.67
Status field indicating whether the ICMP code needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDlci 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.68
DLCI to use to traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..512  

alaQoSConditionDlciStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.69
Status field indicating whether the DLCI needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.70
Used to create/delete conditions according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSConditionSourcePortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.71
Source physical port range end to use for traffic classification. Must be greater than port range start to indicate a range. When '1', use source port as a single port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..52  

alaQoSConditionDestinationPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.72
Destination physical port range end to use for traffic classification. Must be greater than port range start to indicate a range. When '1', use destination port as a single port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..52  

alaQoSConditionSourceIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.73
Source IP port range end to use for traffic classification. Must be greater than source IP port range start to indicate a range. When '0', use source IP port as a single IP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionDestinationIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.74
Destination IP port range end to use for traffic classification. Must be greater than destination IP port range start to indicate a range. When '0', use destination IP port as a single IP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionSourceTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.75
Source TCP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionSourceTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.76
Status field indicating whether the source TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.77
Source TCP port range end to use for traffic classification. Must be greater than source TCP port range start to indicate a range. When '0', use source TCP port as a single TCP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionDestinationTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.78
Destination TCP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionDestinationTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.79
Status field indicating whether the destination TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.80
Destination TCP port range end to use for traffic classification. Must be greater than destination TCP port range start to indicate a range. When '0', use destination TCP port as a single TCP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionSourceUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.81
Source UDP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionSourceUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.82
Status field indicating whether the source UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.83
Source UDP port range end to use for traffic classification. Must be greater than source UDP port range start to indicate a range. When '0', use source UDP port as a single UDP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionDestinationUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.84
Destination UDP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionDestinationUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.85
Status field indicating whether the destination UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.86
Destination UDP port range end to use for traffic classification. Must be greater than destination UDP port range start to indicate a range. When '0', use destination UDP port as a single TCP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionEthertype 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.87
Ethertype value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSConditionEthertypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.88
Status field indicating whether the ethertype value needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionTcpFlags 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.89
Use any/all specifieid TCP flags for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER all(1), any(2)  

alaQoSConditionTcpFlagsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.90
Status field indicating whether the TCP flag bits needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionTcpFlagsVal 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.91
TCP flags values used for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSConditionTcpFlagsValStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.92
Not used
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionTcpFlagsMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.93
Mask of TCP flags bits used for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSConditionTcpFlagsMaskStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.94
Not used
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionTcpEstablished 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.95
Look for established TCP sessions in classification
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConditionSourceIpv6Addr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.96
Source IPv6 address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSConditionSourceIpv6AddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.97
Status field indicating whether the source IPv6 address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionSourceIpv6Mask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.98
Source IPv6 mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSConditionDestinationIpv6Addr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.99
Destination IPv6 address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSConditionDestinationIpv6AddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.100
Status field indicating whether the destination IPv6 address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionDestinationIpv6Mask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.101
Destination IPv6 mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSConditionIpv6Traffic 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.102
classify IPV6 traffic
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConditionIpv6NH 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.103
NH value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSConditionIpv6NHStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.104
Status field indicating whether the NH value needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionIpv6FlowLabel 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.105
FL value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..1048575  

alaQoSConditionIpv6FlowLabelStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.106
Status field indicating whether the flow label value needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionMcastIpv6Addr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.107
Multicast IPv6 address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSConditionMcastIpv6AddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.108
Status field indicating whether the multicast IPv6 address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionMcastIpv6Mask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.109
Multicast IPv6 mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSConditionDscpEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.110
DSCP value to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

alaQoSConditionInnerSourceVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.111
Customer VLAN to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSConditionInnerSourceVlanStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.112
Status field indicating whether the inner VLAN needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionInner8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.113
Customer 802.1p to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSConditionInner8021pStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.114
Status field indicating whether the inner 802.1p needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionVrfName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.115
Name of Vrf to match traffic in
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionVrfNameStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.116
Status field indicating whether the traffic from a specific vrf needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSCondition8021pEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.117
802.1p range end value to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSConditionInner8021pEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.118
Inner 802.1p range end value to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSConditionSourceVlanGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.119
Source vlan group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionSourceVlanGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.120
Status field indicating whether to use for traffic classification (enabled) or not (disabled) for source vlan group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConditionInnerSourceVlanGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.121
Inner Source vlan group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConditionInnerSourceVlanGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.3.1.122
Status field indicating whether to use for traffic classification (enabled) or not (disabled) for inner source vlan group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4
Table of QoS AppliedCondition definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedConditionEntry

alaQoSAppliedConditionEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1
Definition of QoS AppliedCondition
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedConditionEntry  

alaQoSAppliedConditionName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.1
Name of condition
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.2
What entity created the condition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedConditionSourceSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.3
Source physical slot used for traffic classification When 0, the port identifies an aggregate
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

alaQoSAppliedConditionSourceSlotStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.4
Status field indicating whether the source physical slot and port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourcePort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.5
Source physical port range start to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedConditionSourcePortGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.6
Source physical port group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionSourcePortGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.7
Status field indicating whether the source physical port group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.8
Destination physical slot used for traffic classification When 0, the port identifies an aggregate
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

alaQoSAppliedConditionDestinationSlotStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.9
Status field indicating whether the destination physical slot and port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.10
Destination physical port range start to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedConditionDestinationPortGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.11
Destination physical port group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionDestinationPortGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.12
Status field indicating whether the destination physical port group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.13
Source physical interface type to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSAppliedConditionSourceInterfaceTypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.14
Status field indicating whether the source physical interface type needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.15
Destination physical interface type to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSAppliedConditionDestinationInterfaceTypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.16
Status field indicating whether the destination physical interface type needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceMacAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.17
Source MAC address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

alaQoSAppliedConditionSourceMacAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.18
Status field indicating whether the source MAC address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceMacMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.19
Source MAC mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

alaQoSAppliedConditionSourceMacGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.20
Source MAC group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionSourceMacGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.21
Status field indicating whether the source MAC group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationMacAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.22
Destination MAC address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

alaQoSAppliedConditionDestinationMacAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.23
Status field indicating whether the destination MAC address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationMacMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.24
Destination MAC mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

alaQoSAppliedConditionDestinationMacGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.25
Destination MAC group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionDestinationMacGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.26
Status field indicating whether the destination MAC group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.27
Source VLAN to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSAppliedConditionSourceVlanStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.28
Status field indicating whether the source VLAN needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.29
Destination VLAN to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSAppliedConditionDestinationVlanStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.30
Status field indicating whether the destination VLAN needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedCondition8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.31
802.1p value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedCondition8021pStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.32
Status field indicating whether the 802.1p value needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.33
Source IP address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedConditionSourceIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.34
Status field indicating whether the source IP address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.35
Source IP mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedConditionSourceNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.36
Source network group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionSourceNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.37
Status field indicating whether the source network group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.38
Destination IP address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedConditionDestinationIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.39
Status field indicating whether the destination IP address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.40
Destination IP mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedConditionDestinationNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.41
Destination network group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionDestinationNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.42
Status field indicating whether the destination network group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionMulticastIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.43
Multicast IP address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedConditionMulticastIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.44
Status field indicating whether the multicast IP address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionMulticastIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.45
Multicast IP mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedConditionMulticastNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.46
Multicast network group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionMulticastNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.47
Status field indicating whether the multicast network group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTos 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.48
TOS value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedConditionTosStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.49
Status field indicating whether the TOS value & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTosMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.50
TOS mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedConditionDscp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.51
DSCP value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedConditionDscpStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.52
Status field indicating whether the DSCP value & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDscpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.53
DSCP mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedConditionIpProtocol 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.54
IP protocol to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSAppliedConditionIpProtocolStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.55
Status field indicating whether the IP protocol needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.56
Source IP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionSourceIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.57
Status field indicating whether the source IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.58
Destination IP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionDestinationIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.59
Status field indicating whether the destination IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionService 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.60
Name of service to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionServiceStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.61
Status field indicating whether the service needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionServiceGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.62
Name of service group to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionServiceGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.63
Status field indicating whether the service group needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionIcmpType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.64
ICMP type to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSAppliedConditionIcmpTypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.65
Status field indicating whether the ICMP type needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionIcmpCode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.66
ICMP code to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSAppliedConditionIcmpCodeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.67
Status field indicating whether the ICMP code needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDlci 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.68
DLCI to use to traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..512  

alaQoSAppliedConditionDlciStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.69
Status field indicating whether the DLCI needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.70
Used to create/delete conditions according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedConditionSourcePortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.71
Source physical port range end to use for traffic classification. Must be greater than port range start to indicate a range. When '1', use source port as a single port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedConditionDestinationPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.72
Destination physical port range end to use for traffic classification. Must be greater than port range start to indicate a range. When '1', use destination port as a single port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedConditionSourceIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.73
Source IP port range end to use for traffic classification. Must be greater than source IP port range start to indicate a range. When '0', use source IP port as a single IP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionDestinationIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.74
Destination IP port range end to use for traffic classification. Must be greater than destination IP port range start to indicate a range. When '0', use destination IP port as a single IP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionSourceTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.75
Source TCP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionSourceTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.76
Status field indicating whether the source TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.77
Source TCP port range end to use for traffic classification. Must be greater than source TCP port range start to indicate a range. When '0', use source TCP port as a single TCP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionDestinationTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.78
Destination TCP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionDestinationTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.79
Status field indicating whether the destination TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.80
Destination TCP port range end to use for traffic classification. Must be greater than destination TCP port range start to indicate a range. When '0', use destination TCP port as a single TCP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionSourceUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.81
Source UDP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionSourceUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.82
Status field indicating whether the source UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.83
Source UDP port range end to use for traffic classification. Must be greater than source UDP port range start to indicate a range. When '0', use source UDP port as a single UDP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionDestinationUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.84
Destination UDP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionDestinationUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.85
Status field indicating whether the destination UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.86
Destination UDP port range end to use for traffic classification. Must be greater than destination UDP port range start to indicate a range. When '0', use destination UDP port as a single TCP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionEthertype 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.87
Ethertype value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedConditionEthertypeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.88
Status field indicating whether the ethertype value needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTcpFlags 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.89
Use any/all specifieid TCP flags for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER all(1), any(2)  

alaQoSAppliedConditionTcpFlagsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.90
Status field indicating whether the TCP flag bits needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTcpFlagsVal 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.91
TCP flags values used for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedConditionTcpFlagsValStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.92
Not used
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTcpFlagsMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.93
Mask of TCP flags bits used for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedConditionTcpFlagsMaskStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.94
Not used
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionTcpEstablished 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.95
Look for established TCP sessions in classification
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedConditionSourceIpv6Addr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.96
Source IPv6 address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

alaQoSAppliedConditionSourceIpv6AddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.97
Status field indicating whether the source IPv6 address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionSourceIpv6Mask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.98
Source IPv6 mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

alaQoSAppliedConditionDestinationIpv6Addr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.99
Destination IPv6 address to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

alaQoSAppliedConditionDestinationIpv6AddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.100
Status field indicating whether the destination IPv6 address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionDestinationIpv6Mask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.101
Destination IPv6 mask to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

alaQoSAppliedConditionIpv6Traffic 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.102
classify IPV6 traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedConditionIpv6NH 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.103
NH value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSAppliedConditionIpv6NHStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.104
Status field indicating whether the NH value needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionIpv6FlowLabel 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.105
FL value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1048575  

alaQoSAppliedConditionIpv6FlowLabelStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.106
Status field indicating whether the flow label value needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionMcastIpv6Addr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.107
Multicast IPv6 address to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSAppliedConditionMcastIpv6AddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.108
Status field indicating whether the multicast IPv6 address & mask needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionMcastIpv6Mask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.109
Multicast IPv6 mask to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  Ipv6Address  

alaQoSAppliedConditionDscpEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.110
DSCP value to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedConditionInnerSourceVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.111
Customer VLAN to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSAppliedConditionInnerSourceVlanStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.112
Status field indicating whether the inner VLAN needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionInner8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.113
Customer 802.1p to use for traffic classification
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedConditionInner8021pStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.114
Status field indicating whether the inner 802.1p needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionVrfName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.115
Name of Vrf to match traffic in
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionVrfNameStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.116
Status field indicating whether the traffic from a specific vrf needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedCondition8021pEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.117
802.1p range end value to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedConditionInner8021pEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.118
Inner 802.1p range end value to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedConditionSourceVlanGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.119
Source vlan group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionSourceVlanGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.120
Status field indicating whether to use for traffic classification (enabled) or not (disabled) for source vlan group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedConditionInnerSourceVlanGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.121
Inner Source vlan group to use for traffic classification
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedConditionInnerSourceVlanGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.4.1.122
Status field indicating whether to use for traffic classification (enabled) or not (disabled) for inner source vlan group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5
Table of QoS Service definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSServiceEntry

alaQoSServiceEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1
Definition of QoS Service
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSServiceEntry  

alaQoSServiceName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.1
Name of the service
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSServiceSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.2
What entity created the service.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSServiceProtocol 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.3
protocol field for Service
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSServiceSourceIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.4
Source IP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceSourceIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.5
Status field indicating whether the source IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceDestinationIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.6
Destination IP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceDestinationIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.7
Status field indicating whether the destination IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.8
Used to create/delete services according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSServiceSourceIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.9
Source IP port range end to use for traffic classification. Must be greater than source IP port range start to indicate a range. When '0', use source IP port as a single IP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceDestinationIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.10
Destination IP port range end to use for traffic classification. Must be greater than destination IP port range start to indicate a range. When '0', use destination IP port as a single IP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceSourceTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.11
Source TCP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceSourceTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.12
Status field indicating whether the source TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceSourceTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.13
Source TCP port range end to use for traffic classification. Must be greater than source TCP port range start to indicate a range. When '0', use source TCP port as a single TCP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceDestinationTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.14
Destination TCP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceDestinationTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.15
Status field indicating whether the destination TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceDestinationTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.16
Destination TCP port range end to use for traffic classification. Must be greater than destination TCP port range start to indicate a range. When '0', use destination TCP port as a single TCP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceSourceUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.17
Source UDP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceSourceUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.18
Status field indicating whether the source UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceSourceUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.19
Source UDP port range end to use for traffic classification. Must be greater than source UDP port range start to indicate a range. When '0', use source UDP port as a single UDP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceDestinationUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.20
Destination UDP port range start to use for traffic classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceDestinationUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.21
Status field indicating whether the destination UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSServiceDestinationUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.5.1.22
Destination UDP port range end to use for traffic classification. Must be greater than destination UDP port range start to indicate a range. When '0', use destination UDP port as a single UDP port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6
Table of QoS AppliedService definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedServiceEntry

alaQoSAppliedServiceEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1
Definition of QoS AppliedService
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedServiceEntry  

alaQoSAppliedServiceName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.1
Name of the service
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedServiceSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.2
What entity created the service.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedServiceProtocol 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.3
protocol field for AppliedService
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSAppliedServiceSourceIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.4
Source IP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceSourceIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.5
Status field indicating whether the source IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedServiceDestinationIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.6
Destination IP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceDestinationIpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.7
Status field indicating whether the destination IP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedServiceRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.8
Used to create/delete services according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedServiceSourceIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.9
Source IP port range end to use for traffic classification. Must be greater than source IP port range start to indicate a range. When '0', use source IP port as a single IP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceDestinationIpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.10
Destination IP port range end to use for traffic classification. Must be greater than destination IP port range start to indicate a range. When '0', use destination IP port as a single IP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceSourceTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.11
Source TCP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceSourceTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.12
Status field indicating whether the source TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedServiceSourceTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.13
Source TCP port range end to use for traffic classification. Must be greater than source TCP port range start to indicate a range. When '0', use source TCP port as a single TCP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceDestinationTcpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.14
Destination TCP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceDestinationTcpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.15
Status field indicating whether the destination TCP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedServiceDestinationTcpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.16
Destination TCP port range end to use for traffic classification. Must be greater than destination TCP port range start to indicate a range. When '0', use destination TCP port as a single TCP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceSourceUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.17
Source UDP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceSourceUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.18
Status field indicating whether the source UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedServiceSourceUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.19
Source UDP port range end to use for traffic classification. Must be greater than source UDP port range start to indicate a range. When '0', use source UDP port as a single UDP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceDestinationUdpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.20
Destination UDP port range start to use for traffic classification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedServiceDestinationUdpPortStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.21
Status field indicating whether the destination UDP port range needs to be matched(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedServiceDestinationUdpPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.6.1.22
Destination UDP port range end to use for traffic classification. Must be greater than destination UDP port range start to indicate a range. When '0', use destination UDP port as a single UDP port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSServiceGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7
Table of QoS ServiceGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSServiceGroupsEntry

alaQoSServiceGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1
Definition of QoS ServiceGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSServiceGroupsEntry  

alaQoSServiceGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1.1
Name of service group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSServiceGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1.2
What entity created the service group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSServiceGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.7.1.3
Used to create/delete service groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedServiceGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8
Table of QoS AppliedServiceGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedServiceGroupsEntry

alaQoSAppliedServiceGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1
Definition of QoS AppliedServiceGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedServiceGroupsEntry  

alaQoSAppliedServiceGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1.1
Name of service group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedServiceGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1.2
What entity created the service group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedServiceGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.8.1.3
Used to create/delete service groups according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSServiceGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9
Table of QoS ServiceGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSServiceGroupEntry

alaQoSServiceGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9.1
Definition of QoS ServiceGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSServiceGroupEntry  

alaQoSServiceGroupServiceName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9.1.1
Name of service in service group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSServiceGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.9.1.2
Used to create/delete service group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedServiceGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10
Table of QoS AppliedServiceGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedServiceGroupEntry

alaQoSAppliedServiceGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10.1
Definition of QoS AppliedServiceGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedServiceGroupEntry  

alaQoSAppliedServiceGroupServiceName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10.1.1
Name of service in service group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedServiceGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.10.1.2
Used to create/delete service group entries according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSNetworkGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11
Table of QoS NetworkGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSNetworkGroupsEntry

alaQoSNetworkGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1
Definition of QoS NetworkGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSNetworkGroupsEntry  

alaQoSNetworkGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1.1
Name of network group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSNetworkGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1.2
What entity created the network group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSNetworkGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.11.1.3
Used to create/delete network groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedNetworkGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12
Table of QoS AppliedNetworkGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedNetworkGroupsEntry

alaQoSAppliedNetworkGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1
Definition of QoS AppliedNetworkGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedNetworkGroupsEntry  

alaQoSAppliedNetworkGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1.1
Name of network group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedNetworkGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1.2
What entity created the network group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedNetworkGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.12.1.3
Used to create/delete network groups according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSNetworkGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13
Table of QoS NetworkGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSNetworkGroupEntry

alaQoSNetworkGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1
Definition of QoS NetworkGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSNetworkGroupEntry  

alaQoSNetworkGroupIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1.1
IP address for network group entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

alaQoSNetworkGroupIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1.2
IP mask for network group entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

alaQoSNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.13.1.3
Used to create/delete network group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedNetworkGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14
Table of QoS AppliedNetworkGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedNetworkGroupEntry

alaQoSAppliedNetworkGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1
Definition of QoS AppliedNetworkGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedNetworkGroupEntry  

alaQoSAppliedNetworkGroupIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1.1
IP address for network group entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedNetworkGroupIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1.2
IP mask for network group entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.14.1.3
Used to create/delete network group entries according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSMACGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15
Table of QoS MACGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSMACGroupsEntry

alaQoSMACGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1
Definition of QoS MACGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSMACGroupsEntry  

alaQoSMACGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1.1
Name of MAC group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSMACGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1.2
What entity created the MAC group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSMACGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.15.1.3
Used to create/delete MAC groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedMACGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16
Table of QoS AppliedMACGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedMACGroupsEntry

alaQoSAppliedMACGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1
Definition of QoS AppliedMACGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedMACGroupsEntry  

alaQoSAppliedMACGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1.1
Name of MAC group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedMACGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1.2
What entity created the MAC group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedMACGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.16.1.3
Used to create/delete MAC groups according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSMACGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17
Table of QoS MACGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSMACGroupEntry

alaQoSMACGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1
Definition of QoS MACGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSMACGroupEntry  

alaQoSMACGroupMacAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1.1
MAC address for MAC group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

alaQoSMACGroupMacMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1.2
MAC mask for MAC group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

alaQoSMACGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.17.1.3
Used to create/delete MAC group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedMACGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18
Table of QoS AppliedMACGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedMACGroupEntry

alaQoSAppliedMACGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1
Definition of QoS AppliedMACGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedMACGroupEntry  

alaQoSAppliedMACGroupMacAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1.1
MAC address for MAC group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

alaQoSAppliedMACGroupMacMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1.2
MAC mask for MAC group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

alaQoSAppliedMACGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.18.1.3
Used to create/delete MAC group entries according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSPortGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19
Table of QoS PortGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSPortGroupsEntry

alaQoSPortGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1
Definition of QoS PortGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSPortGroupsEntry  

alaQoSPortGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1.1
Name of port group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSPortGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1.2
What entity created the port group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSPortGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.19.1.3
Used to create/delete port groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedPortGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20
Table of QoS AppliedPortGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedPortGroupsEntry

alaQoSAppliedPortGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1
Definition of QoS AppliedPortGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedPortGroupsEntry  

alaQoSAppliedPortGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1.1
Name of port group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedPortGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1.2
What entity created the port group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedPortGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.20.1.3
Used to create/delete port groups according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSPortGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21
Table of QoS PortGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSPortGroupEntry

alaQoSPortGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1
Definition of QoS PortGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSPortGroupEntry  

alaQoSPortGroupSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.1
Physical slot for port group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

alaQoSPortGroupPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.2
Physical port range start for port group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..52  

alaQoSPortGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.3
Used to create/delete port group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSPortGroupPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.21.1.4
Physical port range end for port group entry Must be greater than port range start to indicate a range. When '1', use port as a single port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..52  

alaQoSAppliedPortGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22
Table of QoS AppliedPortGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedPortGroupEntry

alaQoSAppliedPortGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1
Definition of QoS AppliedPortGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedPortGroupEntry  

alaQoSAppliedPortGroupSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.1
Physical slot for port group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

alaQoSAppliedPortGroupPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.2
Physical port range start for port group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedPortGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.3
Used to create/delete port group entries according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedPortGroupPortEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.22.1.4
Physical port range end for port group entry Must be greater than port range start to indicate a range. When '1', use port as a single port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..52  

alaQoSMapGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23
Table of QoS MapGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSMapGroupsEntry

alaQoSMapGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1
Definition of QoS MapGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSMapGroupsEntry  

alaQoSMapGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1.1
Name of map group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSMapGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1.2
What entity created the map group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSMapGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.23.1.3
Used to create/delete map groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedMapGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24
Table of QoS AppliedMapGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedMapGroupsEntry

alaQoSAppliedMapGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1
Definition of QoS AppliedMapGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedMapGroupsEntry  

alaQoSAppliedMapGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1.1
Name of map group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedMapGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1.2
What entity created the map group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedMapGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.24.1.3
Used to create/delete map groups according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSMapGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25
Table of QoS MapGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSMapGroupEntry

alaQoSMapGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1
Definition of QoS MapGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSMapGroupEntry  

alaQoSMapGroupKey 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.1
Key range start of map group entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSMapGroupKeyEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.2
Key range end for map group entries. Key range end must be greater than key range start to indicate a range. When '0', use key range start as a single key.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSMapGroupValue 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.3
Value for map group entries. Value to stamp on traffic when keys in the proper range are seen.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSMapGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.25.1.4
Used to create/delete map group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedMapGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26
Table of QoS AppliedMapGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedMapGroupEntry

alaQoSAppliedMapGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1
Definition of QoS AppliedMapGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedMapGroupEntry  

alaQoSAppliedMapGroupKey 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.1
Key range start of map group entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedMapGroupKeyEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.2
Key range end for map group entries. Key range end must be greater than key range start to indicate a range. When '0', use key range start as a single key.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedMapGroupValue 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.3
Value for map group entries. Value to stamp on traffic when keys in the proper range are seen.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedMapGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.26.1.4
Used to create/delete map group entries according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSActionTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27
Table of QoS Action definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSActionEntry

alaQoSActionEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1
Definition of QoS Action
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSActionEntry  

alaQoSActionName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.1
Name of action
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSActionSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.2
What entity created the action.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSActionDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.3
Disposition of traffic using the action. Use to filter out unwanted traffic.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSActionDropAlgorithm 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.4
Which drop algorithm should be used to discard traffic when oversubscribed.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tail(1), wred(2)  

alaQoSActionWredMaximumThreshold 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.5
Bandwidth at which WRED should discard most traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionWredMaximumThresholdStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.6
Status field indicating whether WRED maximum threshold is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionWredMinimumThreshold 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.7
Bandwidth at which WRED should start to discard traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionWredMinimumThresholdStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.8
Status field indicating whether WRED minimum threshold is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionWredMaximumProbability 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.9
Probabilty that traffic will be dropped at WRED maximum threshold.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionWredMaximumProbabilityStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.10
Status field indicating whether WRED maximum probability is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionMinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.11
Minimum bandwidth (Kbits/sec) to guarantee for traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionMinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.12
Status field indicating whether minimum bandwidth is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionMaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.13
Maximum bandwidth (Kbits/sec) allowed for traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionMaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.14
Status field indicating whether maximum bandwidth is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionPeakBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.15
Peak bandwidth (Kbits/sec) allowed for traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionPeakBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.16
Status field indicating whether peak bandwidth is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionPriority 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.17
Internal and queueing priority to use for traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSActionPriorityStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.18
Status field indicating whether priority is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionShared 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.19
When enabled, try and share any resources (queues/limiters/descriptors) when more than one policy uses the same action.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSActionJitter 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.20
Maximum jitter to allow for traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionJitterStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.21
Status field indicating whether jitter is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionLatency 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.22
Maximum latency to allow for traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionLatencyStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.23
Status field indicating whether latency is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionMaximumDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.24
Maximum depth (Kbytes) of queues for traffic. Used for EBS in tri-color marker applications.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionMaximumDepthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.25
Status field indicating whether maximum depth is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionMaximumBuffers 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.26
Maxmimum buffers for queues for traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2047  

alaQoSActionMaximumBuffersStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.27
Status field indicating whether maximum buffers is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAction8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.28
802.1p value to stamp on traffic.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAction8021pStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.29
Status field indicating whether 802.1p is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionTos 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.30
TOS value to stamp on traffic. (High 3 bits of TOS byte)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSActionTosStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.31
Status field indicating whether TOS is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionDscp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.32
TOS value to stamp on traffic. (High 6 bits of TOS byte)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

alaQoSActionDscpStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.33
Status field indicating whether DSCP is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionMapFrom 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.34
What field to use as key for mapping 802.1p/TOS/DSCP priorities
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER b8021p(1), tos(2), dscp(3)  

alaQoSActionMapTo 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.35
What field to rewrite due to remapping 802.1p/TOS/DSCP priorities
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER b8021p(1), tos(2), dscp(3)  

alaQoSActionMapGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.36
Name of the map group to use when remapping 802.1p/TOS/DSCP priorities.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSActionMapGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.37
Status field indicating whether a map group is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionSourceRewriteIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.38
Source IP address to rewrite on traffic.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSActionSourceRewriteIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.39
Status field indicating whether source rewrite IP address & mask is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionSourceRewriteIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.40
Source rewrite IP mask to determine how much of source IP to rewrite.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSActionSourceRewriteNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.41
Name of network group containing source address/masks to rewrite on traffic. Must be a one to on correspondence with source network group entries in the condition.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSActionSourceRewriteNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.42
Status field indicating whether source rewrite network group is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionDestinationRewriteIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.43
Destination IP address to rewrite on traffic.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSActionDestinationRewriteIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.44
Status field indicating whether destination rewrite IP address & mask is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionDestinationRewriteIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.45
Destination rewrite IP mask to determine how much of destination IP to rewrite.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSActionDestinationRewriteNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.46
Name of network group containing destination address/masks to rewrite on traffic. Must be a one to on correspondence with destination network group entries in the condition.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSActionDestinationRewriteNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.47
Status field indicating whether destination rewrite network group is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionLoadBalanceGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.48
Name of load balance group to use for traffic
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..23)  

alaQoSActionLoadBalanceGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.49
Status field indicating whether load balanace group is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionPermanentGatewayIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.50
Next hop gateway to use for traffic
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSActionPermanentGatewayIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.51
Status field indicating whether permanent gateway IP address is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionAlternateGatewayIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.52
Next hop gateway to use for traffic that doesn't have an explicit route. Use this gateway instead of default routes.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

alaQoSActionAlternateGatewayIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.53
Status field indicating whether alternate gateway IP address is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.54
Used to create/delete actions according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSActionMinimumDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.55
Minimum depth (Kbytes) of queues for traffic. Used for CBS in tri-color marker applications.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionMinimumDepthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.56
Status field indicating whether minimum depth is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionVPNAccess 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.57
How to encrypt traffic
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER protect(1), bypass(2), drop(3)  

alaQoSActionNocache 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.58
When enabled, don't make hardware entries for matching flows.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSActionPortdisable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.59
When enabled, disable the physical source port of the traffic.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSActionRedirectSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.60
Destination physical slot for redirected traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

alaQoSActionRedirectSlotStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.61
Status for alaQoSActionRedirectSlotStatus field
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionRedirectPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.62
Destination physical port for redirected traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..52  

alaQoSActionRedirectAgg 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.63
Destination linkagg for redirected traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..32  

alaQoSActionRedirectAggStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.64
Status for alaQoSActionRedirectAggStatus field
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionMirrorSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.65
Destination physical slot for mirrored traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

alaQoSActionMirrorPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.66
Destination physical port for mirrored traffic
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..52  

alaQoSActionMirrorMode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.67
Mirroring mode
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ingress(1), egress(2), both(3)  

alaQoSActionMirrorModeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.68
Status for alaQoSActionMirrorMode field
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionCIR 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.69
Committed Information Rate - bandwidth values in kilobits per second.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionCIRStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.70
Status field indicating whether CIR value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionCBS 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.71
Committed Burst Size - bucket size in byte.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147450880  

alaQoSActionCBSStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.72
Status field indicating whether CBS value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionPIR 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.73
Peak Information Rate - bandwidth values in kilobits per second.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSActionPIRStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.74
Status field indicating whether PIR value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionPBS 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.75
Peak Burst Size - bucket size in byte.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147450880  

alaQoSActionPBSStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.76
Status field indicating whether PBS value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSActionCounterColor 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.27.1.77
Specifies the color mode for the counters which will be used for sr/trTCM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rednonred(1), greennongreen(2), greenred(3), greenyellow(4), redyellow(5)  

alaQoSAppliedActionTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28
Table of QoS AppliedAction definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedActionEntry

alaQoSAppliedActionEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1
Definition of QoS AppliedAction
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedActionEntry  

alaQoSAppliedActionName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.1
Name of action
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedActionSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.2
What entity created the action.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedActionDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.3
Disposition of traffic using the action. Use to filter out unwanted traffic.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSAppliedActionDropAlgorithm 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.4
Which drop algorithm should be used to discard traffic when oversubscribed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tail(1), wred(2)  

alaQoSAppliedActionWredMaximumThreshold 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.5
Bandwidth at which WRED should discard most traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionWredMaximumThresholdStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.6
Status field indicating whether WRED maximum threshold is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionWredMinimumThreshold 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.7
Bandwidth at which WRED should start to discard traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionWredMinimumThresholdStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.8
Status field indicating whether WRED minimum threshold is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionWredMaximumProbability 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.9
Probabilty that traffic will be dropped at WRED maximum threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionWredMaximumProbabilityStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.10
Status field indicating whether WRED maximum probability is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionMinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.11
Minimum bandwidth (Kbits/sec) to guarantee for traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionMinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.12
Status field indicating whether minimum bandwidth is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionMaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.13
Maximum bandwidth (Kbits/sec) allowed for traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionMaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.14
Status field indicating whether maximum bandwidth is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionPeakBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.15
Peak bandwidth (Kbits/sec) allowed for traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionPeakBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.16
Status field indicating whether peak bandwidth is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionPriority 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.17
Internal and queueing priority to use for traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedActionPriorityStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.18
Status field indicating whether priority is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionShared 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.19
When enabled, try and share any resources (queues/limiters/descriptors) when more than one policy uses the same action.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedActionJitter 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.20
Maximum jitter to allow for traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionJitterStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.21
Status field indicating whether jitter is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionLatency 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.22
Maximum latency to allow for traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionLatencyStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.23
Status field indicating whether latency is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionMaximumDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.24
Maximum depth (Kbytes) of queues for traffic. Used for EBS in tri-color marker applications.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionMaximumDepthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.25
Status field indicating whether maximum depth is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionMaximumBuffers 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.26
Maxmimum buffers for queues for traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2047  

alaQoSAppliedActionMaximumBuffersStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.27
Status field indicating whether maximum buffers is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedAction8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.28
802.1p value to stamp on traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedAction8021pStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.29
Status field indicating whether 802.1p is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionTos 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.30
TOS value to stamp on traffic. (High 3 bits of TOS byte)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

alaQoSAppliedActionTosStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.31
Status field indicating whether TOS is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionDscp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.32
TOS value to stamp on traffic. (High 6 bits of TOS byte)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..63  

alaQoSAppliedActionDscpStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.33
Status field indicating whether DSCP is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionMapFrom 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.34
What field to use as key for mapping 802.1p/TOS/DSCP priorities
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER b8021p(1), tos(2), dscp(3)  

alaQoSAppliedActionMapTo 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.35
What field to rewrite due to remapping 802.1p/TOS/DSCP priorities
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER b8021p(1), tos(2), dscp(3)  

alaQoSAppliedActionMapGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.36
Name of the map group to use when remapping 802.1p/TOS/DSCP priorities.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedActionMapGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.37
Status field indicating whether a map group is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionSourceRewriteIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.38
Source IP address to rewrite on traffic.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedActionSourceRewriteIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.39
Status field indicating whether source rewrite IP address & mask is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionSourceRewriteIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.40
Source rewrite IP mask to determine how much of source IP to rewrite.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedActionSourceRewriteNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.41
Name of network group containing source address/masks to rewrite on traffic. Must be a one to on correspondence with source network group entries in the condition.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedActionSourceRewriteNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.42
Status field indicating whether source rewrite network group is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionDestinationRewriteIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.43
Destination IP address to rewrite on traffic.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedActionDestinationRewriteIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.44
Status field indicating whether destination rewrite IP address & mask is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionDestinationRewriteIpMask 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.45
Destination rewrite IP mask to determine how much of destination IP to rewrite.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedActionDestinationRewriteNetworkGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.46
Name of network group containing destination address/masks to rewrite on traffic. Must be a one to on correspondence with destination network group entries in the condition.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedActionDestinationRewriteNetworkGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.47
Status field indicating whether destination rewrite network group is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionLoadBalanceGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.48
Name of load balance group to use for traffic
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..23)  

alaQoSAppliedActionLoadBalanceGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.49
Status field indicating whether load balanace group is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionPermanentGatewayIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.50
Next hop gateway to use for traffic
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedActionPermanentGatewayIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.51
Status field indicating whether permanent gateway IP address is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionAlternateGatewayIpAddr 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.52
Next hop gateway to use for traffic that doesn't have an explicit route. Use this gateway instead of default routes.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

alaQoSAppliedActionAlternateGatewayIpAddrStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.53
Status field indicating whether alternate gateway IP address is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.54
Used to create/delete actions according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedActionMinimumDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.55
Minimum depth (Kbytes) of queues for traffic. Used for CBS in tri-color marker applications.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionMinimumDepthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.56
Status field indicating whether minimum depth is specified(enabled) or not(disabled).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionVPNAccess 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.57
How to encrypt traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER protect(1), bypass(2), drop(3)  

alaQoSAppliedActionNocache 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.58
When enabled, don't make hardware entries for matching flows.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedActionPortdisable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.59
When enabled, disable the physical source port of the traffic.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSAppliedActionRedirectSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.60
Destination physical slot for redirected traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

alaQoSAppliedActionRedirectSlotStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.61
Status for alaQoSAppliedActionRedirectSlotStatus field
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionRedirectPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.62
Destination physical port for redirected traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedActionRedirectAgg 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.63
Destination linkagg for redirected traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32  

alaQoSAppliedActionRedirectAggStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.64
Status for alaQoSAppliedActionRedirectAggStatus field
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionMirrorSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.65
Destination physical slot for mirrored traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

alaQoSAppliedActionMirrorPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.66
Destination physical port for mirrored traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..52  

alaQoSAppliedActionMirrorMode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.67
Mirroring mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ingress(1), egress(2), both(3)  

alaQoSAppliedActionMirrorModeStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.68
Status for alaQoSAppliedActionMirrorMode field
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionCIR 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.69
Committed Information Rate - bandwidth values in kilobits per second.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionCIRStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.70
Status field indicating whether CIR value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionCBS 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.71
Committed Burst Size - bucket size in byte.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147450880  

alaQoSAppliedActionCBSStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.72
Status field indicating whether CBS value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionPIR 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.73
Peak Information Rate - bandwidth values in kilobits per second.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSAppliedActionPIRStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.74
Status field indicating whether PIR value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionPBS 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.75
Peak Burst Size - bucket size in byte.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147450880  

alaQoSAppliedActionPBSStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.76
Status field indicating whether PBS value is specified(enabled) or not(disabled).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedActionCounterColor 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.28.1.77
Specifies the color mode for the counters which will be used for sr/trTCM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rednonred(1), greennongreen(2), greenred(3), greenyellow(4), redyellow(5)  

alaQoSPortTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29
Table of QoS Port definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSPortEntry

alaQoSPortEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1
Definition of QoS Port
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSPortEntry  

alaQoSPortSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.1
Physical slot port resides on
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..16  

alaQoSPortPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.2
Physical port number
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..52  

alaQoSPortEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.3
Pending QoS enable status for the physical port Does not take effect until an 'Apply' command is issued
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSPortAppliedEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.4
Current QoS enable status for the physical port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSPortInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.5
The type of interface QoS matches for this physical port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSPortTrusted 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.6
Status of trusting 802.1p/TOS/DSCP values. When trusted, 802.1p/DSCP values in the packet are passed through the switch. When untrusted, 802.1p/DSCP values are set to the port defaults.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSPortDefault8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.7
802.1p priority value to use for untagged frames arriving on the port and tagged frames when the port is untrusted.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSPortDefaultDSCP 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.8
DSCP value to stamp in frames arriving on the port when the port is untrusted
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..63  

alaQoSPortMaximumReservedBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.9
Pending maximum reservable bandwidth on the port. Policies can reserve up to this much bandwidth. Does not take effect until an 'Apply' is issued
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumReservedBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.10
Pending status field indicating whether to enforce maximum reservable bandwidth on next 'Apply'
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortAppliedMaximumReservedBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.11
Current maximum reservable bandwidth on the port. Policies can reserve up to this much bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortAppliedMaximumReservedBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.12
Current status field indicating whether to enforce maximum reservable bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortMaximumSignalledBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.13
Pending maximum signalled bandwidth on the port. Signalling protocols can reserve up to this much bandwidth. Does not take effect until an 'Apply' is issued
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumSignalledBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.14
Pending status field indicating whether to enforce maximum signalled bandwidth on next 'Apply'
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortAppliedMaximumSignalledBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.15
Current maximum signalled bandwidth on the port. Signalling protocols can reserve up to this much bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortAppliedMaximumSignalledBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.16
Current status field indicating whether to enforce maximum signalled bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortDefaultQueues 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.17
Pending number of default queues for the port Overrides any switch-wide default queue setting
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 8..8  

alaQoSPortAppliedDefaultQueues 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.18
Current number of default queues for the port Overrides any switch-wide default queue setting
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 8..8  

alaQoSPortMaximumDefaultBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.19
Pending maximum default bandwidth (Kbits/sec). Maximum rate for default queues on this port Does not take effect until an 'Apply' command is issued
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumDefaultBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.20
Pending status field indicating whether to enforce maximum default bandwidth on next 'Apply'
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortAppliedMaximumDefaultBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.21
Current maximum default bandwidth (Kbits/sec). Maximum rate for default queues this port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortAppliedMaximumDefaultBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.22
Current status field indicating whether to enforce maximum default bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortMaximumDefaultDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.23
Pending maximum depth of egress queues (Kbytes). Maximum depth of queues on this port Does not take effect until an 'Apply' command is issued
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumDefaultDepthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.24
Pending status field indicating whether to enforce maximum depth on next 'Apply'
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortAppliedMaximumDefaultDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.25
Current maximum depth of egress queues (Kbytes). Maximum depth of queues on this port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortAppliedMaximumDefaultDepthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.26
Current status field indicating whether to enforce maximum depth.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortMaximumDefaultBuffers 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.27
Pending maximum buffers for egress queues. Maximum number of buffers for queues on this port Does not take effect until an 'Apply' command is issued
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumDefaultBuffersStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.28
Pending status field indicating whether to enforce maximum buffers on next 'Apply'
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortAppliedMaximumDefaultBuffers 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.29
Current maximum buffers for egress queues. Maximum number of buffers for queues on this port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortAppliedMaximumDefaultBuffersStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.30
Current status field indicating whether to enforce maximum buffers.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortReset 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.31
Reset all QoS parameters to default values
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSPortPhysicalBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.32
Physical bandwidth of port (Kbit/sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortReservedBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.33
Bandwidth reserved by policies on port (Kbit/sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortSignalledBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.34
Bandwidth reserved by signalling on port (Kbit/sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortCurrentBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.35
Current measured bandwidth of port (Kbits/sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortDefaultQidLow 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.36
Default low queue ID
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortDefaultQidMedium 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.37
Default medium queue ID
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortDefaultQidHigh 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.38
Default high queue ID
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortDefaultQidUrgent 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.39
Default urgent queue ID
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortFloodQid 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.40
ID of the flood queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortQueues 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.41
Number of queues currently on the port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortQueuesCreated 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.42
Number of queue requests on the port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortQueuesFailed 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.43
Number of queue requests that failed on the port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortQueuesPreempted 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.44
Number of queues preempted on the port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.45
Used to create/delete ports according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSPortFirPrio0EnqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.46
Firenze priority 0 enqueue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio0DeqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.47
Firenze priority 0 dequeue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio0EnqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.48
Firenze priority 0 enqueue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio0DeqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.49
Firenze priority 0 dequeue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio0QidDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.50
Firenze priority 0 QID discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio0WredDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.51
Firenze priority 0 WRED discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio0OverflowDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.52
Firenze priority 0 overflow discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1EnqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.53
Firenze priority 1 enqueue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1DeqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.54
Firenze priority 1 dequeue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1EnqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.55
Firenze priority 1 enqueue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1DeqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.56
Firenze priority 1 dequeue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1QidDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.57
Firenze priority 1 QID discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1WredDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.58
Firenze priority 1 WRED discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio1OverflowDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.59
Firenze priority 1 overflow discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2EnqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.60
Firenze priority 2 enqueue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2DeqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.61
Firenze priority 2 dequeue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2EnqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.62
Firenze priority 2 enqueue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2DeqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.63
Firenze priority 2 dequeue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2QidDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.64
Firenze priority 2 QID discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2WredDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.65
Firenze priority 2 WRED discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio2OverflowDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.66
Firenze priority 2 overflow discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3EnqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.67
Firenze priority 3 enqueue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3DeqBytes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.68
Firenze priority 3 dequeue byte count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3EnqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.69
Firenze priority 3 enqueue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3DeqPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.70
Firenze priority 3 dequeue packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3QidDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.71
Firenze priority 3 QID discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3WredDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.72
Firenze priority 3 WRED discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortFirPrio3OverflowDiscardPkts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.73
Firenze priority 3 overflow discard packet count
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSPortDefaultClassification 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.74
Ingress traffic classification parameter for Firenze port What field to interpret as priority for WRED
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER b8021p(1), tos(2), dscp(3)  

alaQoSPortLowPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.75
Weight to use for low priority egress queue on fixed queue blades.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortMediumPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.76
Weight to use for medium priority egress queue on fixed queue blades.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortHighPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.77
Weight to use for high priority egress queue on fixed queue blades.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortUrgentPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.78
Weight to use for urgent priority egress queue on fixed queue blades.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortMaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.79
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this port
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.80
Status field indicating whether to enforce maximum bandwidth on port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortEnqueuingThresholdP0Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.81
Priority 0 FIFO lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP0Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.82
Priority 0 FIFO upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP1Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.83
Priority 1 FIFO lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP1Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.84
Priority 1 FIFO upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP2Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.85
Priority 2 FIFO lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP2Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.86
Priority 2 FIFO upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP3Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.87
Priority 3 FIFO lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdP3Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.88
Priority 3 FIFO upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSPortEnqueuingThresholdStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.89
Status field indicating whether enqueuing thresholds need to be enforced on high density module.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortHighDensity 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.90
Indicates whether this is a high-density port or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSPortServicingMode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.91
Servicing mode for the port
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(0), strictpriority(1), prioritywrr(2), wrr(3), drr(4)  

alaQoSPortFreeFFPRules 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.92
Number of Free FPP rule entries
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortUsedFFPRules 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.93
Number of Used FPP rule entries
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortFreeFFPMasks 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.94
Number of Free FPP mask entries
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortUsedFFPMasks 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.95
Number of Free FPP mask enries
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortSpoofedCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.96
Spoofed packet count
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortNonSpoofedCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.97
Non-spoofed packet count
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSPortQ4PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.98
Weight to use for cos queue 4.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortQ5PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.99
Weight to use for cos queue 5.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortQ6PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.100
Weight to use for cos queue 6.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortQ7PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.101
Weight to use for cos queue 7.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSPortCOS0MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.102
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS0MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.103
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS1MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.104
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS1MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.105
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS2MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.106
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS2MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.107
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS3MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.108
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS3MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.109
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS4MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.110
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS4MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.111
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS5MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.112
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS5MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.113
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS6MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.114
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS6MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.115
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS7MaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.116
Maximum egress bandwidth (Kbits/sec). Maximum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS7MaximumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.117
Status field indicating whether to enforce maximum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS0MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.118
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS0MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.119
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS1MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.120
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS1MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.121
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS2MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.122
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS2MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.123
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS3MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.124
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS3MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.125
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS4MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.126
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS4MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.127
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS5MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.128
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS5MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.129
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS6MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.130
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS6MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.131
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortCOS7MinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.132
Minimum egress bandwidth (Kbits/sec). Minimum rate to send traffic out this queue
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortCOS7MinimumBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.133
Status field indicating whether to enforce minimum bandwidth on queue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortMaximumIngBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.134
Maximum igress bandwidth (Kbits/sec). Maximum rate to recieve traffic in on this port
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSPortMaximumIngBandwidthStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.135
Status field indicating whether to enforce maximum bandwidth on port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortDEIMarking 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.136
This object specifies if, in egress traffic, the DEI/CFI bit will be set or not for the traffic which is not conformant to SLA (Yellow color packets). enabled(1) -- the DEI/CFI bit will be set in egress traffic. disabled(2) -- the DEI/CFI bit will not be set in egress traffic.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortMonitor 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.137
This object is used to monitor a slot/port on which user is interested to get the cos egress statistics. enabled(1) -- monitor the slot/port to gather per port cos egress statistics. disabled(2) -- reset the previously monitored slot/port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSPortDEIMapping 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.29.1.138
This object specifies if, in ingress traffic, the DEI/CFI bit will be set or not for the traffic which is not conformant to SLA (Yellow color packets). enabled(1) -- the DEI/CFI bit will be set in ingress traffic. disabled(2) -- the DEI/CFI bit will not be set in ingress traffic.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConfig 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30
OBJECT IDENTIFIER    

alaQoSConfigEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.1
Is QoS enabled on the switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSConfigDefaultQueues 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.2
Pending number of default queues to create for each port. Can be overridden on a port by port basis. Does not take affect until an 'Apply' command is issued.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..8  

alaQoSConfigAppliedDefaultQueues 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.3
Number of default queues configured at last 'Apply' command.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..8  

alaQoSConfigTrustPorts 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.4
Flag to indicate whether to trust the 802.1p/TOS values on incoming traffic by default. Can be overridden on a port by port basis.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigFlowTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.5
Pending flow timeout (seconds). Flows are removed from hardware/software if no traffic is seen for this many seconds. Does not take effect until an 'Apply' command is issued
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..3600  

alaQoSConfigAppliedFlowTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.6
Current flow timeout (seconds). Flows are removed from hardware/software if no traffic is seen for this many seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..3600  

alaQoSConfigFragmentTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.7
Pending fragment timeout (seconds). Packet fragments are remembered for this many seconds. Does not take effect until an 'Apply' command is issued
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..60  

alaQoSConfigAppliedFragmentTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.8
Current fragment timeout (seconds). Packet fragments are remembered for this many seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..60  

alaQoSConfigReflexiveTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.9
Pending reflexive timeout (seconds). Anticipate reverse flows for reflexive and NAT connections for this long until we see a response. Does not take effect until an 'Apply' command is issued
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..3000  

alaQoSConfigAppliedReflfexiveTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.10
Current reflexive timeout (seconds). Anticipate reverse flows for reflexive and NAT connections for this long until we see a response.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 10..3000  

alaQoSConfigNatTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.11
Pending nat timeout (seconds). Once traffic is seen in both directions for anticipated flows, length of time to remember the flow without seeing traffic in either direction. Does not take effect until an 'Apply' command is issued
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..200000  

alaQoSConfigAppliedNatTimeout 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.12
Current nat timeout (seconds). Once traffic is seen in both directions for anticipated flows, length of time to remember the flow without seeing traffic in either direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 10..200000  

alaQoSConfigClassifyl3Bridged 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.13
Pending indicator for looking at L3/L4 parameters of bridged traffic. Does not take effect until an 'Apply' command is issued.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigAppliedClassifyl3Bridged 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.14
Current indicator for looking at L3/L4 parameters of bridged traffic.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigClassifyFragments 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.15
Pending indicator for classifying fragmented traffic at L4 Does not take effect until an 'Apply' command is issued
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigAppliedClassifyFragments 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.16
Current indicator for classifying fragmented traffic at L4 Does not take effect until an 'Apply' command is issued
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigDefaultBridgedDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.17
Pending disposition of bridged traffic that doesn't match a policy. Does not take effect until an 'Apply' command is issued.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSConfigAppliedDefaultBridgedDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.18
Current disposition of bridged traffic that doesn't match a policy.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSConfigDefaultRoutedDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.19
Pending disposition of routed traffic that doesn't match a policy. Does not take effect until an 'Apply' command is issued.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSConfigAppliedDefaultRoutedDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.20
Current disposition of routed traffic that doesn't match a policy
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSConfigDefaultMulticastDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.21
Pending disposition of IGMP requests that don't match a policy Does not take effect until an 'Apply' command is issued
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSConfigAppliedDefaultMulticastDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.22
Current disposition of IGMP requests that don't match a policy
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSConfigStatsInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.23
Interval in seconds for how often statistics are updated
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..3600  

alaQoSConfigLogLines 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.24
Number of log lines to maintain in the QoS log
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1024  

alaQoSConfigLogLevel 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.25
The level of logging desired. The higher the level, the more verbose the logging
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..9  

alaQoSConfigLogConsole 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.26
Whether QoS log events are logged to the console
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigForwardLog 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.27
Whether QoS forwards logging events to PolicyManager
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigClearLog 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.28
Clear the QoS log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigApply 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.29
Set to apply all pending QoS configuration/policy changes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigRevert 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.30
Set to revert all pending QoS configuration/policy changes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigReset 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.31
Set to reset global QoS configuration parameters to their default values
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigStatsReset 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.32
Set to reset global QoS statistics counters
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigFlush 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.33
Flush all pending policy objects
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigDebug 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.34
Possible debug flags for QoS
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

alaQoSConfigServicingMode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.35
Servicing mode for the system
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER strictpriority(1), prioritywrr(2), wrr(3), drr(4)  

alaQoSConfigLowPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.36
Weight to use for low priority queue(0) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigMediumPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.37
Weight to use for medium priority queue(1) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigHighPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.38
Weight to use for high priority queue(2) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigUrgentPriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.39
Weight to use for urgent priority queue(3) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigQ4PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.40
Weight to use for COS 4 priority queue(4) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigQ5PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.41
Weight to use for COS 5 priority queue(5) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigQ6PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.42
Weight to use for COS 6 priority queue(6) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigQ7PriorityWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.43
Weight to use for COS 7 priority queue(7) on fixed queue blades
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..15  

alaQoSConfigUserportFilter 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.44
Events/protocols to filter on a Userport. Event bits values are: spoof = 1 bpdu = 2 bgp = 4 ospf = 8 rip = 16 vrrp = 32 dhcp-server = 64 pim = 128 dvmrp = 256 is-is = 512 dnsreply = 1024
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSConfigAppliedUserportFilter 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.45
Events/protocols to filter on a Userport. Event bits values are: spoof = 1 bpdu = 2 bgp = 4 ospf = 8 rip = 16 vrrp = 32 dhcp-server = 64 pim = 128 dvmrp = 256 is-is = 512 dnsreply = 1024
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSConfigUserportShutdown 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.46
Events/protocols that trigger admin down of a Userport. Event bits values are: spoof = 1 bpdu = 2 bgp = 4 ospf = 8 rip = 16 vrrp = 32 dhcp-server = 64 pim = 128 dvmrp = 256 is-is = 512 dnsreply = 1024
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSConfigAppliedUserportShutdown 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.47
Events/protocols that trigger admin down of a Userport. Event bits values are: spoof = 1 bpdu = 2 bgp = 4 ospf = 8 rip = 16 vrrp = 32 dhcp-server = 64 pim = 128 dvmrp = 256 is-is = 512 dnsreply = 1024
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSConfigAutoNMS 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.48
Flag to indicate whether to Prioritize NMS traffic by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigAutoPhones 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.49
Auto configure CSBU Phones pri0-7 - will replace the priority. trusted - will allow priority from the orginator to be used. disable - will unconfigure to feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pri0(0), pri1(1), pri2(2), pri3(3), pri4(4), pri5(5), pri6(6), pri7(7), trusted(8), disable(9)  

alaQoSConfigQMPage 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.50
Flag to indicate whether to send back a quarantined page when a client is quarantined but a remediation URL is not specified.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSConfigQMMACGroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.51
Group name for quarantine manager quarantined MACs.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSConfigQMPath 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.52
Default path for remediation server redirect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

alaQoSConfigDEIMapping 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.53
This object specifies, in ingress traffic, the DEI/CFI bit is mapped or not to internal drop precedence or yellow color. enabled(1) -- the DEI/CFI bit is mapped to internal drop precedence or yellow color if that bit is set. disabled(2) -- the DEI/CFI bit is not mapped to drop precedence or yellow color.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConfigDEIMarking 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.54
This object specifies, in egress traffic, the DEI/CFI bit is mapped or not to internal drop precedence or yellow color. enabled(1) -- the DEI/CFI bit is mapped to internal drop precedence or yellow color if that bit is set. disabled(2) -- the DEI/CFI bit is not mapped to drop precedence or yellow color.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSConfigStatsResetEgress 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.30.55
Set to reset global Egress QoS statistics counters
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSQueueTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32
Table of QoS Queue definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSQueueEntry

alaQoSQueueEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1
Definition of QoS Queue
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSQueueEntry  

alaQoSQueueId 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.1
Internal queue identifier
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

alaQoSQueueSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.2
Physical slot queue is destined to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSQueuePort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.3
Physical port queue is destined to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSQueuePortId 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.4
Internal global port id of destination port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSQueueType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.5
Type of queueing done on this queue
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER mammoth(1), priority(2), spwrr(3), wrr(4), drr(5)  

alaQoSQueuePriority 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.6
Queueing priority for the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSQueueMinimumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.7
Minimum bandwidth (Kbits/sec) given to the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueMaximumBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.8
Maximum bandwidth (Kbits/sec) given to the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueAverageBandwidth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.9
Average measured bandwidth (Kbits/sec) for the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueMinimumDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.10
Minimum depth (Kbytes) of the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueMaximumDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.11
Maximum depth (Kbytes) of the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueMaximumBuffers 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.12
Maximum number of buffers for the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSQueue8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.13
802.1p value queue places on traffic
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSQueuePacketsSent 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.14
Number of packets sent through the queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueuePacketsDropped 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.15
Number of packets dropped trying to queue into this queue
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueMaxLength 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.16
Maximum measured length the queue has reached in buffers
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueAverageLength 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.17
Average measured length of the queue in buffers
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueCurrentLength 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.18
Current measured length of the queue in buffers
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSQueueAction 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.32.1.19
Name of the action this queue was created from
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSStats 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31
OBJECT IDENTIFIER    

alaQoSStatsL2Events 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.1
Number of L2 classification events
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL2Matches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.2
Number of L2 classifications matching a policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL2Drops 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.3
Number of L2 classifications matching a drop policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL3IngressEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.4
Number of L3/L4 ingress classification events
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL3IngressMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.5
Number of L3 ingress classifications matching a policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL3IngressDrops 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.6
Number of L3 ingress classifications matching a drop policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL3EgressEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.7
Number of L3/L4 egress classification events
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL3EgressMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.8
Number of L3 egress classifications matching a policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsL3EgressDrops 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.9
Number of L3 egress classifications matching a drop policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsMulticastEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.10
Number of IGMP classification events
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsMulticastMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.11
Number of IGMP classifications matching a policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsMulticastDrops 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.12
Number of IGMP classifications matching a drop policy
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsFragments 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.13
Number of fragments processed by QoS
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsBadFragments 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.14
Number of illegal (offset = 1) fragments
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsUnknownFragments 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.15
Number of out of order fragment pieces
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsReflexiveFlows 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.16
Number of reflexive flow entries
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsReflexiveCorrections 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.17
Number of reflexive flow corrections
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsLoadBalanceFlows 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.18
Number of server load balanced flow entries
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsClassifierMaxNodes 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.19
Highest number of nodes in classifier tree
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsClassifierMaxDepth 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.20
Length of longest path in classifier tree
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsFlowLookups 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.21
Number of flow table lookups
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsFlowHits 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.22
Number of flow table lookup hits
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsSentNIMessages 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.23
Number of messages sent to NIs
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsReceivedNIMessages 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.24
Number of messages received from NIs
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsFailedNIMessages 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.25
Number of failed message attemptes to NIs
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsSpoofedEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.26
Total Number of spoofed events
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsNonSpoofedEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.27
Total number of non-spoofed events
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSStatsDropServicesEvents 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.31.28
Total number of packets matching the DropServices group
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSSlotTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33
Table of QoS Slot definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSSlotEntry

alaQoSSlotEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1
Definition of QoS Slot
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSSlotEntry  

alaQoSSlotSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.1
Physical slot number
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

alaQoSSlotSlice 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.2
Physical device number on slot
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..4  

alaQoSSlotType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.3
Type of hardware in this slot/slice
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER mammoth(1), kodiak(2), mailbox(3), coronado(4), ixe2424(5), kite(6), fuji(7)  

alaQoSSlotMaxBuffers 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.4
Maximum total buffers on this slot/slice
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotFreeBuffers1 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.5
Current free buffers in list 1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotFreeBuffers2 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.6
Current free buffers in list 2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold1Low 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.7
Buffer are not given to low priority traffic from list 1 when free buffers in list 1 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold1Medium 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.8
Buffer are not given to medium priority traffic from list 1 when free buffers in list 1 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold1High 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.9
Buffer are not given to high priority traffic from list 1 when free buffers in list 1 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold1Urgent 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.10
Buffer are not given to urgent priority traffic from list 1 when free buffers in list 1 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold2Low 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.11
Buffer are not given to low priority traffic from list 2 when free buffers in list 2 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold2Medium 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.12
Buffer are not given to medium priority traffic from list 2 when free buffers in list 2 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold2High 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.13
Buffer are not given to high priority traffic from list 2 when free buffers in list 2 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotThreshold2Urgent 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.14
Buffer are not given to urgent priority traffic from list 2 when free buffers in list 2 is less than this threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotBuffersDenied 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.15
Buffers denied on this slot
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotBuffersDeniedAverage 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.16
Average number of denied buffers over time
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotBuffersDropped 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.17
Buffers dropped on this slot
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotBuffersDroppedAverage 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.18
Average number of dropped buffers over time
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSSlotWredThresholdP0Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.19
Priority 0 WRED lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP0Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.20
Priority 0 WRED upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP1Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.21
Priority 1 WRED lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP1Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.22
Priority 1 WRED upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP2Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.23
Priority 2 WRED lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP2Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.24
Priority 2 WRED upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP3Lower 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.25
Priority 3 WRED lower threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredThresholdP3Upper 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.26
Priority 3 WRED upper threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotWredAverageCounterWeight 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.27
The weight used in the WRED algorithm. It is used as a negative power of 2
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

alaQoSSlotWredThresholdStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.28
Status field indicating whether WRED maximum thresholds are specified(enable) or not(disable).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSSlotCbqThresholdMode 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.29
Servicing mode for the CBQ thresholds for high density modules
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER prioritywrr(1), wrr(2), strictpriority(3)  

alaQoSSlotCbqThresholdP1 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.30
Priority 1 CBQ threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotCbqThresholdP2 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.31
Priority 2 CBQ threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotCbqThresholdP3 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.32
Priority 3 CBQ threshold for high density module
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

alaQoSSlotHighDensity 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.33.1.33
Indicates whether this is a high-density slice or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSClassify 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34
OBJECT IDENTIFIER    

alaQoSClassifyClassify 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.1
Which classification routine to run on the sample packet
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER l2(1), l3(2), multicast(3)  

alaQoSClassifyApplied 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.2
What set of policies QoS uses when testing the classifier. When yes(1) the applied policies are used. When no(2) the pending policies are used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSClassifySourceSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.3
Source physical slot to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16  

alaQoSClassifySourcePort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.4
Source physical port to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..52  

alaQoSClassifySourceInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.5
Source interface type to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(0), ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSClassifyDestinationSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.6
Destination physical slot to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16  

alaQoSClassifyDestinationPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.7
Destination physical port to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..52  

alaQoSClassifyDestinationInterfaceType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.8
Destination interface type to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(0), ethernet(1), wan(2), ethernet10(3), ethernet100(4), ethernet1G(5), ethernet10G(6), aggregate(7)  

alaQoSClassifySourceMac 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.9
Source MAC address to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

alaQoSClassifyDestinationMac 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.10
Destination MAC address to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

alaQoSClassifySourceVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.11
Source VLAN to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSClassifyDestinationVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.12
Destination VLAN to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSClassify8021p 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.13
802.1p value to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

alaQoSClassifySourceIp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.14
Source IP address to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

alaQoSClassifyDestinationIp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.15
Destination IP address to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

alaQoSClassifyMulticastIp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.16
Multicast IP address to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

alaQoSClassifyTos 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.17
TOS value to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

alaQoSClassifyDscp 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.18
DSCP value to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..63  

alaQoSClassifyIpProtocol 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.19
IP protocol value to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

alaQoSClassifySourceIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.20
Source IP port to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSClassifyDestinationIpPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.21
Destination IP port to submit when testing classifier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSClassifyExecute 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.22
Writing to this field tells QoS to run the classifier on the current packet headers. The classifier stores the results in result fields. The next 'set' to the table will clear all fields before actually performing the set.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSClassifyL2SourceResultRule 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.23
Matching rule for L2 (source)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSClassifyL2SourceResultDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.24
Result disposition for L2 (source)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSClassifyL2DestinationResultRule 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.25
Matching rule for L2 (destination)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSClassifyL2DestinationResultDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.26
Result disposition for L2 (destination)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSClassifyL3ResultRule 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.27
Matching rule for L3
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSClassifyL3ResultDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.28
Result disposition for L3
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSClassifyIGMPResultRule 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.29
Matching rule for IGMP request
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSClassifyIGMPResultDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.30
Result disposition for IGMP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSClassifyMulticastResultRule 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.31
Matching rule for multicast
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSClassifyMulticastResultDisposition 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.34.32
Result disposition for multicast
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER accept(1), drop(2), deny(3)  

alaQoSSlotProtocolTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35
Table of QoS SlotProtocol definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSSlotProtocolEntry

alaQoSSlotProtocolEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1
Definition of QoS SlotProtocol
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSSlotProtocolEntry  

alaQoSSlotProtocolId 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.1
Used on high density module classification in the MAC. This is the protocol ID used between the CAM and priority descriptors.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER user1(1), user2(2), user3(3), user4(4), unknown(5)  

alaQoSSlotProtocolEthertype 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.2
Used on high density module classification in the MAC. This is the Ethernet type used between the CAM for classification.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSSlotProtocolDsap 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.3
Used on high density module classification in the MAC. This is the destination SAP in an 802.3 packet.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSSlotProtocolSsap 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.4
Used on high density module classification in the MAC. This is the source SAP in an 802.3 packet.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

alaQoSSlotProtocol8023Enabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.5
Used on high density module classification in the MAC. This will enable 802.3 checking on the CAM entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSSlotProtocolType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.6
Used on high density module classification in the MAC. This positions the CAM entry in the list. Priority will put the entries in the front of the CAM, giving it priority. fallback will put the entry at the end.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER priority(1), fallback(2)  

alaQoSSlotProtocolRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.35.1.7
Used to create/delete slot protoocols according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSPortProtocolTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36
Table of QoS PortProtocol definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSPortProtocolEntry

alaQoSPortProtocolEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1
Definition of QoS PortProtocol
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSPortProtocolEntry  

alaQoSPortProtocolId 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.1
Used on high density module classification in the MAC. This is the protocol id that needs to be changed.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER bpdu(1), lcpsnap(2), lcpeth(3), ipv4(4), arp(5), rarp(6), ipv6(7), ipx(8), apple(9), sna(10), decnet(11), user1(12), user2(13), user3(14), user4(15)  

alaQoSPortProtocolClassification 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.2
Used on high density module classification in the MAC. This determines what type of classification is used to find priority.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER b8021p(1), tos(2), dscp(3)  

alaQoSPortProtocolPriorityP0 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.3
Used on high density module classification in the MAC. This is the new priority for P0 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP1 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.4
Used on high density module classification in the MAC. This is the new priority for P1 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP2 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.5
Used on high density module classification in the MAC. This is the new priority for P2 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP3 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.6
Used on high density module classification in the MAC. This is the new priority for P3 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP4 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.7
Used on high density module classification in the MAC. This is the new priority for P4 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP5 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.8
Used on high density module classification in the MAC. This is the new priority for P5 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP6 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.9
Used on high density module classification in the MAC. This is the new priority for P6 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolPriorityP7 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.10
Used on high density module classification in the MAC. This is the new priority for P7 to be mapped to.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSPortProtocolRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.36.1.11
Used to create/delete rows according to RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSSlotDscpTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.37
Table of QoS SlotDscp definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSSlotDscpEntry

alaQoSSlotDscpEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.37.1
Definition of QoS SlotDscp
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSSlotDscpEntry  

alaQoSSlotDscpIndex 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.37.1.1
Used on high density module classification in the MAC This is the index into the DSCP table to access.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..63  

alaQoSSlotDscpPriority 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.37.1.2
Used on high density module classification in the MAC. This is the priority of the index of the DSCP table.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..3  

alaQoSSlotPcamTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38
Table of QoS SlotPcam definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSSlotPcamEntry

alaQoSSlotPcamEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1
Definition of QoS SlotPcam
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSSlotPcamEntry  

alaQoSSlotPcamId 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.1
Used on high density module classification in the MAC. This is the index used in the PCAM.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..24  

alaQoSSlotPcamEthertype 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.2
Used on high density module classification in the MAC. This is the Ethernet type in the CAM.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSSlotPcamDsap 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.3
Used on high density module classification in the MAC. This is the destination SAP in an 802.3 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSSlotPcamSsap 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.4
Used on high density module classification in the MAC. This is the source SAP in an 802.3 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSSlotPcam8023Enabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.5
Used on high density module classification in the MAC. This will enable 802.3 checking on the CAM entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSSlotPcamProtocolNumber 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.6
Used on high density module classification in the MAC. This identifies the protocol number of the CAM entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSSlotPcamEnableEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.7
Used on high density module to enable the pcam entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSSlotPcamEnable8023 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.8
Used on high density module to indiciate if 802.3 is enabled in the pcam entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSSlotPcamEnableDsap 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.9
Used on high density module to indiciate if DSAP is enabled in the pcam entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSSlotPcamEnableSsap 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.10
Used on high density module to indiciate if SSAP is enabled in the pcam entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSSlotPcamEnableEthertype 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.38.1.11
Used on high density module to indiciate if Ethertype is enabled in the pcam entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

alaQoSPortPdiTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39
Table of QoS PortPdi definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSPortPdiEntry

alaQoSPortPdiEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1
Definition of QoS PortPdi
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSPortPdiEntry  

alaQoSPortPdiId 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.1
Used on high density module classification in the MAC. This is the index used in the PDI.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..16  

alaQoSPortPdiPriorityType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.2
Used on high density module classification in the MAC. This is the classification type on the port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP0 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.3
Used on high density module classification in the MAC. This is the internal priority mapping for a P0 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP1 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.4
Used on high density module classification in the MAC. This is the internal priority mapping for a P1 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP2 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.5
Used on high density module classification in the MAC. This is the internal priority mapping for a P2 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP3 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.6
Used on high density module classification in the MAC. This is the internal priority mapping for a P3 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP4 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.7
Used on high density module classification in the MAC. This is the internal priority mapping for a P4 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP5 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.8
Used on high density module classification in the MAC. This is the internal priority mapping for a P5 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP6 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.9
Used on high density module classification in the MAC. This is the internal priority mapping for a P6 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSPortPdiPriorityP7 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.39.1.10
Used on high density module classification in the MAC. This is the internal priority mapping for a P7 packet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

alaQoSValidityPeriodTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40
Table of QoS ValidityPeriod definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSValidityPeriodEntry

alaQoSValidityPeriodEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1
Definition of QoS ValidityPeriod
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSValidityPeriodEntry  

alaQoSValidityPeriodName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.1
Name of validity period
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSValidityPeriodSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.2
What entity created the validity period.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSValidityPeriodDays 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.3
Bitfield for each day of the week this validity period is active. Monday is least significant, Sunday is most significant.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSValidityPeriodDaysStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.4
Status field indicating whether the validity period has specific active days of the month.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSValidityPeriodMonths 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.5
Bitfield for each month this validity period is active. January is least significant. Decemeber is most significant.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

alaQoSValidityPeriodMonthsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.6
Status field indicating whether the validity period has specific active days of the week.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSValidityPeriodHour 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.7
Time of day this period becomes active. Format is 'hh:mm'
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..7)  

alaQoSValidityPeriodHourStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.8
Status field indicating whether the validity period has specific active hours of the day.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSValidityPeriodEndHour 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.9
Time of day this period becomes inactive. Format is 'hh:mm'
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..7)  

alaQoSValidityPeriodInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.10
Date/time when the validity period begins. Format is 'mm/dd/yyyy hh:mm'
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..19)  

alaQoSValidityPeriodIntervalStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.11
Status field indicating whether the validity period has a specific active date-time interval.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSValidityPeriodEndInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.12
Date/time when the validity period ends. Format is 'mm/dd/yyyy hh:mm'
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..19)  

alaQoSValidityPeriodRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.40.1.13
Used to create/delete validity periods according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedValidityPeriodTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41
Table of QoS AppliedValidityPeriod definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedValidityPeriodEntry

alaQoSAppliedValidityPeriodEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1
Definition of QoS AppliedValidityPeriod
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedValidityPeriodEntry  

alaQoSAppliedValidityPeriodName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.1
Name of validity period
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedValidityPeriodSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.2
What entity created the validity period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedValidityPeriodDays 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.3
Bitfield for each day of the week this validity period is active. Monday is least significant, Sunday is most significant.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedValidityPeriodDaysStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.4
Status field indicating whether the validity period has specific active days of the month.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedValidityPeriodMonths 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.5
Bitfield for each month this validity period is active. January is least significant. Decemeber is most significant.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

alaQoSAppliedValidityPeriodMonthsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.6
Status field indicating whether the validity period has specific active days of the week.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedValidityPeriodHour 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.7
Time of day this period becomes active. Format is 'hh:mm'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..7)  

alaQoSAppliedValidityPeriodHourStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.8
Status field indicating whether the validity period has specific active hours of the day.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedValidityPeriodEndHour 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.9
Time of day this period becomes inactive. Format is 'hh:mm'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..7)  

alaQoSAppliedValidityPeriodInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.10
Date/time when the validity period begins. Format is 'mm/dd/yyyy hh:mm'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..19)  

alaQoSAppliedValidityPeriodIntervalStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.11
Status field indicating whether the validity period has a specific active date-time interval.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

alaQoSAppliedValidityPeriodEndInterval 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.12
Date/time when the validity period ends. Format is 'mm/dd/yyyy hh:mm'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..19)  

alaQoSAppliedValidityPeriodRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.41.1.13
Used to create/delete validity periods according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSImportTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42
Table of QoS Import definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSImportEntry

alaQoSImportEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1
Definition of QoS Import
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSImportEntry  

alaQoSImportIndex 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.1
Index of entry in import list
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

alaQoSImportText 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.2
Text or filename to import
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..63)  

alaQoSImportPrecedence 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.3
Precedence to use for policies imported from file
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSImportPrefix 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.4
Prefix for policy names that are imported
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..11)  

alaQoSImportSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.5
Slot on which to apply imported policy(s)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..52  

alaQoSImportPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.6
Starting port on which to apply imported policy(s)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

alaQoSImportPortend 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.7
Ending port on which to apply imported policy(s)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

alaQoSImportPortgroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.8
Portgroup on which to apply imported policy(s)
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSImportRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.42.1.9
Used to create/delete imports according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedImportTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43
Table of QoS AppliedImport definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedImportEntry

alaQoSAppliedImportEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1
Definition of QoS AppliedImport
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedImportEntry  

alaQoSAppliedImportIndex 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.1
Index of entry in import list
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

alaQoSAppliedImportText 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.2
Text or filename to import
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..63)  

alaQoSAppliedImportPrecedence 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.3
Precedence to use for policies imported from file
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

alaQoSAppliedImportPrefix 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.4
Prefix for policy names that are imported
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..11)  

alaQoSAppliedImportSlot 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.5
Slot on which to apply imported policy(s)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..52  

alaQoSAppliedImportPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.6
Starting port on which to apply imported policy(s)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

alaQoSAppliedImportPortend 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.7
Ending port on which to apply imported policy(s)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

alaQoSAppliedImportPortgroup 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.8
Portgroup on which to apply imported policy(s)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedImportRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.43.1.9
Used to create/delete imports according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSRuleGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44
Table of QoS RuleGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSRuleGroupsEntry

alaQoSRuleGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44.1
Definition of QoS RuleGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSRuleGroupsEntry  

alaQoSRuleGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44.1.1
Name of rule group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSRuleGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44.1.2
What entity created the rule group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSRuleGroupsType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44.1.3
Type of rule group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), unp(2), vrf(3), ingress(4), egress(5), slb(6)  

alaQoSRuleGroupsEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44.1.4
Is this rule grop enabled or not
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSRuleGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.44.1.5
Used to create/delete rule groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedRuleGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45
Table of QoS AppliedRuleGroups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedRuleGroupsEntry

alaQoSAppliedRuleGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45.1
Definition of QoS AppliedRuleGroups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedRuleGroupsEntry  

alaQoSAppliedRuleGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45.1.1
Name of rule group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedRuleGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45.1.2
What entity created the service group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedRuleGroupsType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45.1.3
What entity created the rule group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER defualt(1), unp(2), vrf(3), ingress(4), egress(5), slb(6)  

alaQoSAppliedRuleGroupsEnabled 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45.1.4
Is this rule grop enabled or not
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alaQoSAppliedRuleGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.45.1.5
Used to create/delete rule groups according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSRuleGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46
Table of QoS RuleGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSRuleGroupEntry

alaQoSRuleGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1
Definition of QoS RuleGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSRuleGroupEntry  

alaQoSRuleGroupRuleName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1.1
Name of rule in rule group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSRuleGroupMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1.2
Number of times this rule has been matched.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSRuleGroupCountType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1.3
Which rule statistics counters to update if not all are available
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER packets(1), bytes(2)  

alaQoSRuleGroupPacketCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1.4
Counter for packets patching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleGroupByteCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1.5
Counter for bytes matching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSRuleGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.46.1.6
Used to create/delete rule group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedRuleGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47
Table of QoS AppliedRuleGroup definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedRuleGroupEntry

alaQoSAppliedRuleGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1
Definition of QoS AppliedRuleGroup
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedRuleGroupEntry  

alaQoSAppliedRuleGroupRuleName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1.1
Name of rule in rule group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedRuleGroupMatches 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1.2
Number of times this rule has been matched.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

alaQoSAppliedRuleGroupCountType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1.3
Which rule statistics counters to update if not all are available
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER packets(1), bytes(2)  

alaQoSAppliedRuleGroupPacketCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1.4
Counter for packets patching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleGroupByteCount 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1.5
Counter for bytes matching this rule
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

alaQoSAppliedRuleGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.47.1.6
Used to create/delete rule group entries according to the RowStatus convention
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

alaQoSVlanGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.48
Table of QoS Vlan Groups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSVlanGroupsEntry

alaQoSVlanGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.48.1
Definition of QoS Vlan Groups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSVlanGroupsEntry  

alaQoSVlanGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.48.1.1
Name of Vlan group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSVlanGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.48.1.2
What entity created the Vlan group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSVlanGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.48.1.3
Used to create/delete Vlan groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedVlanGroupsTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.49
Table of QoS Applied Vlan Groups definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedVlanGroupsEntry

alaQoSAppliedVlanGroupsEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.49.1
Definition of QoS Applied Vlan Groups
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedVlanGroupsEntry  

alaQoSAppliedVlanGroupsName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.49.1.1
Name of Applied Vlan group
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..31)  

alaQoSAppliedVlanGroupsSource 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.49.1.2
What entity created the Vlan group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ldap(1), cli(2), blt(3), api(4), imp(5)  

alaQoSAppliedVlanGroupsStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.49.1.3
Used to create/delete Vlan groups according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSVlanGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.50
Table of QoS Vlan Group definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSVlanGroupEntry

alaQoSVlanGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.50.1
Definition of QoS Vlan Group
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSVlanGroupEntry  

alaQoSVlanGroupVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.50.1.1
Vlan range start for vlan group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

alaQoSVlanGroupVlanEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.50.1.2
Vlan range end for vlan group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

alaQoSVlanGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.50.1.3
Used to create/delete vlan group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSAppliedVlanGroupTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.51
Table of QoS Applied Vlan Group definitions
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSAppliedVlanGroupEntry

alaQoSAppliedVlanGroupEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.51.1
Definition of QoS Applied Vlan Group
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSAppliedVlanGroupEntry  

alaQoSAppliedVlanGroupVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.51.1.1
Vlan range start for vlan group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4095  

alaQoSAppliedVlanGroupVlanEnd 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.51.1.2
Vlan range end for vlan group entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4095  

alaQoSAppliedVlanGroupStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.51.1.3
Used to create/delete vlan group entries according to the RowStatus convention
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSHwLoopbackProfileTable 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52
Table of QoS Hw Loopback Profiles
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QoSHwLoopbackProfileEntry

alaQoSHwLoopbackProfileEntry 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1
Definition of QoS Hw Loopback Profiles
Status: current Access: not-accessible
OBJECT-TYPE    
  QoSHwLoopbackProfileEntry  

alaQoSHwLoopbackProfileName 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.1
Name of Profile Name
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..31)  

alaQoSHwLoopbackSourceMac 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.2
Source MAC address to use for Hardware Loopback profile configuration
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

alaQoSHwLoopbackDestinationMac 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.3
Destination MAC address to use for Hardware Loopback profile configuration
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

alaQoSHwLoopbackVlan 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.4
Vlan used in Hardware Loopback Profile Config
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..4094  

alaQoSHwLoopbackPort 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.5
Loopback Port ifindex used in Hardware Loopback Profile Config
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

alaQoSHwLoopbackType 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.6
The type of Hardware Profile Config, inward and outward
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER inward(1), outward(2)  

alaQoSHwLoopbackProfileStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.7
The status of the Hardware Profile Config
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER config(0), start(1), stop(2)  

alaQoSHwLoopbackProfileRowStatus 1.3.6.1.4.1.6486.801.1.2.1.22.1.1.52.1.8
Used to create/delete the Profile Config
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

alaQoSMIBConformance 1.3.6.1.4.1.6486.801.1.2.1.22.1.2
Branch for QoS Managed Conformance Information.
Status: current Access: read-create
OBJECT-IDENTITY    

alaQoSMIBGroups 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1
Branch for QoS Units of Conformance.
Status: current Access: read-create
OBJECT-IDENTITY    

alaQoSMIBCompliances 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.2
Branch for QoS Compliance Statements.
Status: current Access: read-create
OBJECT-IDENTITY    

alaQoSMIBRuleObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.1
Collections of objects providing information for Rules
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedRuleObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.2
Collections of objects providing information for applied Rules
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBConditionObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.3
Collections of objects providing information for Conditions
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedConditionObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.4
Collections of objects providing information for applied Conditions
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBServiceObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.5
Collections of objects providing information for Services
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedServiceObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.6
Collections of objects providing information for applied Services
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBServiceGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.7
Collections of objects providing information for ServiceGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedServiceGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.8
Collections of objects providing information for applied ServiceGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBServiceGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.9
Collections of objects providing information for ServiceGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedServiceGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.10
Collections of objects providing information for applied ServiceGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBNetworkGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.11
Collections of objects providing information for NetworkGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedNetworkGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.12
Collections of objects providing information for applied NetworkGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBNetworkGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.13
Collections of objects providing information for NetworkGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedNetworkGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.14
Collections of objects providing information for applied NetworkGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBMACGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.15
Collections of objects providing information for MACGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedMACGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.16
Collections of objects providing information for applied MACGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBMACGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.17
Collections of objects providing information for MACGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedMACGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.18
Collections of objects providing information for applied MACGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBPortGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.19
Collections of objects providing information for PortGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedPortGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.20
Collections of objects providing information for applied PortGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBPortGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.21
Collections of objects providing information for PortGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedPortGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.22
Collections of objects providing information for applied PortGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBMapGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.23
Collections of objects providing information for MapGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedMapGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.24
Collections of objects providing information for applied MapGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBMapGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.25
Collections of objects providing information for MapGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedMapGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.26
Collections of objects providing information for applied MapGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBActionObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.27
Collections of objects providing information for Actions
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedActionObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.28
Collections of objects providing information for applied Actions
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBPortObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.29
Collections of objects providing information for Ports
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBConfigObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.30
Collections of objects providing information for Configs
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBStatsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.31
Collections of objects providing information for Statss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBQueueObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.32
Collections of objects providing information for Queues
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBSlotObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.33
Collections of objects providing information for Slots
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBClassifyObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.34
Collections of objects providing information for Classifys
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBRuleGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.35
Collections of objects providing information for RuleGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedRuleGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.36
Collections of objects providing information for applied RuleGroupss
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBRuleGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.37
Collections of objects providing information for RuleGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBAppliedRuleGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.38
Collections of objects providing information for applied RuleGroups
Status: current Access: read-create
OBJECT-GROUP    

alaQoSVlanGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.39
Collections of objects providing QoS Vlan Groups definitions.
Status: current Access: read-create
OBJECT-GROUP    

alaQoSAppliedVlanGroupsObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.40
Collections of objects providing applied QoS Vlan Groups definitions.
Status: current Access: read-create
OBJECT-GROUP    

alaQoSVlanGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.41
Collections of objects providing QoS Vlan Groups definitions.
Status: current Access: read-create
OBJECT-GROUP    

alaQoSAppliedVlanGroupObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.42
Collections of objects providing applied QoS Vlan Groups definitions.
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBHwLoopBackProfileObjects 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.1.43
Collections of objects providing information for Hardware Loopback
Status: current Access: read-create
OBJECT-GROUP    

alaQoSMIBCompliance 1.3.6.1.4.1.6486.801.1.2.1.22.1.2.2.1
Compliance statement for QoS.
Status: current Access: read-create
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor