ALCATEL-IND1-IPV6-MIB

File: ALCATEL-IND1-IPV6-MIB.mib (65602 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMP-FRAMEWORK-MIB
SNMPv2-CONF	IPV6-TC	ALCATEL-IND1-BASE
IPV6-MIB	ALCATEL-IND1-VIRTUALROUTER-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-IDENTITY	OBJECT-TYPE
NOTIFICATION-TYPE	IpAddress	Integer32
Unsigned32	Counter32	TEXTUAL-CONVENTION
PhysAddress	RowStatus	TimeStamp
TruthValue	DateAndTime	SnmpAdminString
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
Ipv6Address	Ipv6IfIndexOrZero	softentIND1Ipv6
ipv6IfIndex	ipv6RouteEntry	alaVirtualRouterName

Defined Types

AlaIPv6AddressPrefix
A data type for the 8 byte IPv6 prefixes for EUI-64 addresses
TEXTUAL-CONVENTION
	OCTET STRING	Size(8)

AlaIPv6InterfaceEntry
SEQUENCE
	alaIPv6InterfaceRowStatus	RowStatus
	alaIPv6InterfaceDescription	SnmpAdminString
	alaIPv6InterfaceMtu	Unsigned32
	alaIPv6InterfaceType	INTEGER
	alaIPv6InterfaceAdminStatus	INTEGER
	alaIPv6InterfaceSendRouterAdvertisements	INTEGER
	alaIPv6InterfaceMaxRtrAdvInterval	Unsigned32
	alaIPv6InterfaceAdvManagedFlag	TruthValue
	alaIPv6InterfaceAdvOtherConfigFlag	TruthValue
	alaIPv6InterfaceAdvReachableTime	Unsigned32
	alaIPv6InterfaceAdvRetransTimer	Unsigned32
	alaIPv6InterfaceAdvDefaultLifetime	Unsigned32
	alaIPv6InterfaceName	SnmpAdminString
	alaIPv6InterfaceAdvSendMtu	TruthValue
	alaIPv6InterfaceReachableTime	Unsigned32
	alaIPv6InterfaceBaseReachableTime	Unsigned32
	alaIPv6InterfaceMinRtrAdvInterval	Unsigned32
	alaIPv6InterfaceClockSkew	Unsigned32
	alaIPv6InterfaceRetransTimer	Unsigned32
	alaIPv6InterfaceDADTransmits	Unsigned32
	alaIPv6InterfaceAdvHopLimit	Unsigned32
	alaIPv6InterfaceLPND	INTEGER
	alaIPv6InterfaceRAFilter	INTEGER
	alaIPv6InterfaceNeighborLimit	Unsigned32
	alaIPv6InterfaceRetransBackoff	Unsigned32
	alaIPv6InterfaceRetransMax	Unsigned32

AlaIPv6ConfigTunnelEntry
SEQUENCE
	alaIPv6ConfigTunnelV4Source	IpAddress
	alaIPv6ConfigTunnelV4Dest	IpAddress

AlaIPv6InterfaceAddressEntry
SEQUENCE
	alaIPv6InterfaceAddressRowStatus	RowStatus
	alaIPv6InterfaceAddress	Ipv6Address
	alaIPv6InterfaceAddressPrefixLength	Unsigned32
	alaIPv6InterfaceAddressAnycastFlag	TruthValue
	alaIPv6InterfaceAddressDADStatus	INTEGER

AlaIPv6InterfaceEUI64AddressEntry
SEQUENCE
	alaIPv6InterfaceEUI64AddressRowStatus	RowStatus
	alaIPv6InterfaceEUI64AddressPrefix	AlaIPv6AddressPrefix
	alaIPv6InterfaceEUI64AddressPrefixLength	Unsigned32
	alaIPv6InterfaceEUI64AddressIdentifier	OCTET STRING

AlaIPv6NeighborEntry
SEQUENCE
	alaIPv6NeighborNetAddress	Ipv6Address
	alaIPv6NeighborPhysAddress	PhysAddress
	alaIPv6NeighborSlot	Unsigned32
	alaIPv6NeighborPort	Unsigned32
	alaIPv6NeighborType	INTEGER
	alaIPv6NeighborState	INTEGER
	alaIPv6NeighborLastUpdated	TimeStamp
	alaIPv6NeighborRowStatus	RowStatus
	alaIPv6NeighborLifetime	Unsigned32
	alaIPv6NeighborReachability	INTEGER
	alaIPv6NeighborChassis	Unsigned32

AlaIPv6StaticRouteEntry
SEQUENCE
	alaIPv6StaticRouteDest	Ipv6Address
	alaIPv6StaticRoutePfxLength	Integer32
	alaIPv6StaticRouteIfIndex	Ipv6IfIndexOrZero
	alaIPv6StaticRouteNextHop	Ipv6Address
	alaIPv6StaticRouteMetric	Unsigned32
	alaIPv6StaticRouteRowStatus	RowStatus

AlaIPv6HostEntry
SEQUENCE
	alaIPv6HostName	SnmpAdminString
	alaIPv6HostAddress	Ipv6Address
	alaIPv6HostRowStatus	RowStatus

AlaIPv6InterfacePrefixEntry
SEQUENCE
	alaIPv6InterfacePrefixRowStatus	RowStatus
	alaIPv6InterfacePrefix	Ipv6Address
	alaIPv6InterfacePrefixLength	Unsigned32
	alaIPv6InterfacePrefixValidLifetime	Unsigned32
	alaIPv6InterfacePrefixOnLinkFlag	TruthValue
	alaIPv6InterfacePrefixPreferredLifetime	Unsigned32
	alaIPv6InterfacePrefixAutonomousFlag	TruthValue
	alaIPv6InterfacePrefixSource	INTEGER
	alaIPv6InterfacePrefixValidLifetimeDecrement	TruthValue
	alaIPv6InterfacePrefixValidLifetimeExpire	DateAndTime
	alaIPv6InterfacePrefixPreferredLifetimeDecrement	TruthValue
	alaIPv6InterfacePrefixPreferredLifetimeExpire	DateAndTime

AlaIPv6PMTUEntry
SEQUENCE
	alaIPv6PMTUDest	Ipv6Address
	alaIPv6PMTU	Unsigned32
	alaIPv6PMTUExpire	Unsigned32
	alaIPv6PMTUHits	Counter32
	alaIPv6PMTUUpdates	Counter32

AlaIPv6RouteFlagsEntry
SEQUENCE
	alaIPv6RouteFlagsUp	TruthValue
	alaIPv6RouteFlagsGateway	TruthValue
	alaIPv6RouteFlagsHost	TruthValue
	alaIPv6RouteFlagsStatic	TruthValue
	alaIPv6RouteFlagsCloneable	TruthValue
	alaIPv6RouteFlagsDiscard	TruthValue
	alaIPv6RouteFlagsECMP	TruthValue
	alaIPv6RouteFlagsTransient	TruthValue

AlaIPv6LocalUnicastEntry
SEQUENCE
	alaIPv6LocalUnicastGlobalID	OCTET STRING
	alaIPv6LocalUnicastSubnetID	OCTET STRING
	alaIPv6LocalUnicastInterfaceID	OCTET STRING
	alaIPv6LocalUnicastPrefixLength	Unsigned32
	alaIPv6LocalUnicastEUI64	TruthValue
	alaIPv6LocalUnicastRowStatus	RowStatus

AlaIPv6RAFilterTrustedEntry
SEQUENCE
	alaIPv6RAFilterTrustedChassis	Unsigned32
	alaIPv6RAFilterTrustedSlot	Unsigned32
	alaIPv6RAFilterTrustedPort	Unsigned32
	alaIPv6RAFilterTrustedRowStatus	RowStatus

Defined Values

alcatelIND1IPv6MIB		1.3.6.1.4.1.6486.801.1.2.1.29.1
This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): Propietary IPv6 MIB definitions The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2013 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
MODULE-IDENTITY

alcatelIND1IPv6MIBNotifications		1.3.6.1.4.1.6486.801.1.2.1.29.1.0
Branch For IPv6 MIB Subsystem Notifications.
Status: current	Access: read-only
OBJECT-IDENTITY

alcatelIND1IPv6MIBObjects		1.3.6.1.4.1.6486.801.1.2.1.29.1.1
OBJECT IDENTIFIER

alaIPv6Config		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1
OBJECT IDENTIFIER

alaIPv6ClearNeighbors		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.1
Clear all non-static entries from the Neighbor table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

alaIPv6ClearTraffic		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.2
Reset all IPv6 traffic counters.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

alaIPv6ClearPMTUTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.3
Clear the path MTU table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

alaIPv6PMTUMinLifetime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.4
Set the minimum lifetime for entries in the path MTU table.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	10..1440

alaIPv6NeighborStaleLifetime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.5
Set the minimum lifetime for neighbor entries in the stale state. In older versions of this MIB the default was specified as 1440 minutes.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	5..2880

alaIPv6GlobalID		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.6
The global ID used in the creation of local IPv6 unicast addresses (RFC 4193). An explicit value may be specified for the global ID or this object may be set to all zero to have a global ID be created based on the algorithm from the RFC.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(5)

alaIPv6VirtualSourceMAC		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.7
If set to enable(1) when a packet's source address is a VRRP virtual IPv6 address, the corresponding VRRP virtual MAC will be used as the source L2 address. If set to disable(2), the default, the interface's real MAC will be used as the source L2 address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

alaIPv6NeighborLimit		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.8
The system-wide maximum size of the neighbor cache. A value of 0 indicates that no limit will be enforced. The minimum value is 200 entries.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

alaIPv6NeighborVRFLimit		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.1.9
The maximum size of the neighbor cache for a specific VRF. A value of 0 indicates that no limit is set. The minimum value is 200 entries.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

alaIPv6InterfaceTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2
Table allowing the creation and removal of IPv6 interfaces. The table is indexed by ipv6IfIndex. The value of ipv6IfIndex shall be a four byte value in one of the following formats: 0x0000vvvv - The interface for VLAN vvvv 0x0100tttt - The interface for tunnel tttt 0x02000001 - The IPv6 loopback interface The loopback interface configuration cannot be modified.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6InterfaceEntry

alaIPv6InterfaceEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1
An IPv6 interface entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6InterfaceEntry

alaIPv6InterfaceRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.1
Used to control the addition and removal of IPv6 interfaces.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6InterfaceDescription		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.2
The IPv6 interface's description.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

alaIPv6InterfaceMtu		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.3
The IPv6 interface's maximum transmission unit.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6InterfaceType		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.4
The interface type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), vlan(2), tunnel(3), loopback(4)

alaIPv6InterfaceAdminStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.5
Interface administrative status.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

alaIPv6InterfaceSendRouterAdvertisements		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.6
Specify whether the router sends periodic router advertisements and responds to router solicitations on the interface. The default value for most interfaces is enable(1). Some interface types (e.g. 6to4 tunnel) cannot send router advertisements so the default (and only) value for those interfaces is disable(2).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

alaIPv6InterfaceMaxRtrAdvInterval		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.7
The maximum time allowed between sending unsolicited multicast router advertisements from the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	4..1800

alaIPv6InterfaceAdvManagedFlag		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.8
The TRUE/FALSE value to be placed in the 'Managed address configuration' flag field in router advertisements.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfaceAdvOtherConfigFlag		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.9
The TRUE/FALSE value to be placed in the 'Other stateful configuration' flag field in router advertisements.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfaceAdvReachableTime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.10
The value to be placed in the Reachable Time field in the router advertisements sent over this interface. The value zero means unspecified by this router.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..3600000

alaIPv6InterfaceAdvRetransTimer		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.11
The value to be placed in the Retrans Timer field in the router advertisements sent over this interface. The value zero means unspecified by this router.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6InterfaceAdvDefaultLifetime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.12
The value to be placed in the Router Lifetime field in the router advertisements sent over this interface. The value MUST be either zero, 1, or between alaIPv6InterfaceMaxRtrAdvInterval and 9000 seconds. The special value zero indicates that the router is not to be used as a default router. The special value 1 indicates that this object's true value should be computed using the formula 3 * alaIPv6InterfaceMaxRtrAdvInterval.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..9000

alaIPv6InterfaceName		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.13
The mandatory user-assigned name for the interface. Since the loopback interface is created without user interaction, the name 'loopback' will be automatically assigned.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

alaIPv6InterfaceAdvSendMtu		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.14
The TRUE/FALSE value that determines whether the MTU option is sent in Router Advertisements.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfaceReachableTime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.15
In the absence of any reachability notification, the amount of time a neighbor reached via this interface will remain in the reachable state before transitioning to the stale state. Computed to be between .5 and 1.5 times the alaIPv6InterfaceBaseReachableTime.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

alaIPv6InterfaceBaseReachableTime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.16
The base value used to compute the reachable time for neighbors reached via this interface. See alaIPv6InterfaceReachableTime above.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	10..3600

alaIPv6InterfaceMinRtrAdvInterval		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.17
The minimum time allowed between sending unsolicited multicast router advertisements from the interface. The time must be a minimum of 3 seconds and no more than .75 times the value of alaIPv6InterfaceMaxRtrAdvInterval. Setting this object to the special value of 0 indicates that the minimum interval should be automatically recalculated using the formula .33 times the value of alaIPv6InterfaceMaxRtrAdvInterval.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1350

alaIPv6InterfaceClockSkew		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.18
Router Advertisement decrementing timers must be consistent in all Advertisements on the link. The clock skew accounts for link propogation delays and poorly synchronized clocks.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..3600

alaIPv6InterfaceRetransTimer		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.19
The amount of time to wait before retransmitting a Neighbor Solicitation during neighbor discovery.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1000..30000

alaIPv6InterfaceDADTransmits		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.20
The number of Neighbor Solicitations to send during Duplicate Address Detection. A value of 0 indicates that DAD will not be performed for addresses assigned to the interface.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..10

alaIPv6InterfaceAdvHopLimit		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.21
The value placed in the current hop limit field of router advertisements.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

alaIPv6InterfaceLPND		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.22
Enable/disable local proxy neighbor discovery.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

alaIPv6InterfaceRAFilter		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.23
Enable/disable RA filtering.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

alaIPv6InterfaceNeighborLimit		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.24
The maximum number o neighbor entries that may be cached on this interface. A value of 0 indicates that no limit is set. The minimum value is 10.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6InterfaceRetransBackoff		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.25
The neighbor unreachability detection exponential backoff base. A value of 1 indicates the use of fixed interval retransmissions.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..3

alaIPv6InterfaceRetransMax		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.2.1.26
The maximum number of neighbor solicitations to be sent during neighbor discovery or neighbor unreachability detection.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..10

alaIPv6TunnelConfig		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3
OBJECT IDENTIFIER

alaIPv6ConfigTunnelTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2
Table for IPv6 configured tunnels. This table contains the tunnel-specific information extending the corresponding tunnel interface entry in alaIPv6InterfaceTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6ConfigTunnelEntry

alaIPv6ConfigTunnelEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1
A entry contains the objects for an IPv6 configured tunnel.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6ConfigTunnelEntry

alaIPv6ConfigTunnelV4Source		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.1
The source IPv4 address for the tunnel.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

alaIPv6ConfigTunnelV4Dest		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.3.2.1.2
The destination IPv4 address for the tunnel.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

alaIPv6InterfaceAddressTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4
Table allowing the creation and removal of IPv6 addresses assigned to interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6InterfaceAddressEntry

alaIPv6InterfaceAddressEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1
An IPv6 interface address entry. The same link-local address may be assigned to multiple interfaces. A global address may only be assigned to a single interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6InterfaceAddressEntry

alaIPv6InterfaceAddressRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.1
Used to control the addition and removal of IPv6 interface addresses.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6InterfaceAddress		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.2
An IPv6 address (or prefix for EUI-64 addresses) assigned to the interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

alaIPv6InterfaceAddressPrefixLength		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.3
The number of bits that are significant in the IPv6 address' prefix.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	3..128

alaIPv6InterfaceAddressAnycastFlag		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.4
This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfaceAddressDADStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.4.1.5
The status of duplicate address detection for this address. The only value that may be set via SNMP is 'check' when the current status is 'duplicate'. In such cases, duplicate address detection will be performed again for the address.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	unknown(0), pending(1), duplicate(2), passed(3), check(4)

alaIPv6InterfaceEUI64AddressTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5
Table allowing the creation and removal of IPv6 addresses formed by appending an EUI-64 interface identifier to the specified prefix. This table is mainly used for the creation of such addresses. After creation they can be managed via the alaIPv6InterfaceAddressTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6InterfaceEUI64AddressEntry

alaIPv6InterfaceEUI64AddressEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1
An IPv6 interface EUI-64 address entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6InterfaceEUI64AddressEntry

alaIPv6InterfaceEUI64AddressRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.1
Used to control the addition and removal of IPv6 interface EUI-64 addresses.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6InterfaceEUI64AddressPrefix		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.2
The prefix for the EUI-64 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6AddressPrefix

alaIPv6InterfaceEUI64AddressPrefixLength		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.3
The number of bits that are significant in the IPv6 address' prefix.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	3..64

alaIPv6InterfaceEUI64AddressIdentifier		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.5.1.4
The interface's EUI-64 identifier which is combined with the prefix to form the IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(8)

alaIPv6NeighborTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6
The IPv6 neighbor table. Much of this information is available in the RFC-2465 ipv6NetToMediaTable. However, that table does not allow the static configuration of neighbor entries (all objects except for ipv6NetToMediaValid are read-only).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6NeighborEntry

alaIPv6NeighborEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1
Each entry contains one IPv6 address to `physical' address equivalence (a neighbor).
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6NeighborEntry

alaIPv6NeighborNetAddress		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.1
The neighbor's IPv6 Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

alaIPv6NeighborPhysAddress		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.2
The neighbor's media-dependent `physical' address.
Status: current	Access: read-create
OBJECT-TYPE
	PhysAddress

alaIPv6NeighborSlot		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.3
The slot used to reach the neighbor. When creating a static neighbor the slot must be specified. On read, a value of zero indicates the slot is not known/not applicable.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6NeighborPort		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.4
The port used to reach the neighbor. When creating a static neighbor the port must be specified. On read, a value of zero indicates the port is not known/not applicable.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6NeighborType		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.5
The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address. All entries added via this table will have the type static(3) and only static entries may be removed via this table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), dynamic(2), static(3), local(4)

alaIPv6NeighborState		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.6
The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	reachable(1), stale(2), delay(3), probe(4), invalid(5), unknown(6)

alaIPv6NeighborLastUpdated		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.7
The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

alaIPv6NeighborRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.8
Used to control the addition and removal of static entries in the neighbor table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6NeighborLifetime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.9
The remaining time the neighbor will stay in its current state. External events may cause a state change before the expiry of this lifetime. A value of zero indicates the neighbor will remain in its current state indefinitely.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

alaIPv6NeighborReachability		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.10
The reachability status of the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	confirmed(1), unconfirmed(2), incomplete(3)

alaIPv6NeighborChassis		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.6.1.11
On a multi-chasis system, the chassis used to reach the neighbor. On a single-chassis system this value is always 0. On read, a value of zero may indicate that the chassis is not known/not applicable.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6StaticRouteTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7
This table has been superseded by alaIprmV6StaticRouteTable in ALCATEL-IND1-IPRMV6-MIB. Table allowing the creation and removal of static IPv6 routes.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6StaticRouteEntry

alaIPv6StaticRouteEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1
A static route entry.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	AlaIPv6StaticRouteEntry

alaIPv6StaticRouteDest		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.1
The destination IPv6 address of this static route. This object may not take a Multicast address value.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

alaIPv6StaticRoutePfxLength		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.2
Indicates the prefix length of the destination address.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	0..128

alaIPv6StaticRouteIfIndex		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.3
If the next hop address is a link-local address, this is the ipv6IfIndex value of the interface over which the destination is reached. For all other next hop address types the value is zero.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Ipv6IfIndexOrZero

alaIPv6StaticRouteNextHop		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.4
The IPv6 address of the next hop towards the destination.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Ipv6Address

alaIPv6StaticRouteMetric		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.5
The routing metric for this route. The lower the value, the higher the priority for the static route.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6StaticRouteRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.7.1.6
Used to control the addition and removal of static routes.
Status: obsolete	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6HostTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8
Local table mapping host names to IPv6 addresses. This provides the equivalent of /etc/hosts for IPv6.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6HostEntry

alaIPv6HostEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1
A entry maps a host name to an IPv6 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6HostEntry

alaIPv6HostName		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.1
A host name to be mapped to an IPv6 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

alaIPv6HostAddress		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.2
The IPv6 address mapped to the host name.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

alaIPv6HostRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.8.1.3
Allows host name/IPv6 address mappings to be created and deleted in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6InterfacePrefixTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9
Table allowing the creation and removal of IPv6 prefixes to be placed in Prefix Information options in Router Advertisement messages sent from the interface. Default: all prefixes that the router advertises via routing protocols as being on-link for the interface from which the advertisement is sent. The link-local prefix is not included in the list of advertised prefixes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6InterfacePrefixEntry

alaIPv6InterfacePrefixEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1
An IPv6 interface prefix entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6InterfacePrefixEntry

alaIPv6InterfacePrefixRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.1
Used to control the addition and removal of IPv6 interface prefixes for Router ADvertisement messages.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6InterfacePrefix		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.2
The prefix associated with this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

alaIPv6InterfacePrefixLength		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.3
The length of the prefix in bits.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..127

alaIPv6InterfacePrefixValidLifetime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.4
The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6InterfacePrefixOnLinkFlag		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.5
The value to be placed in the on-link flag (L-bit) field in the Prefix Information option.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfacePrefixPreferredLifetime		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.6
The value to be placed in the Preferred Lifetime in the Prefix Information option, in seconds. The designated value of 4,294,967,295 represents infinity.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alaIPv6InterfacePrefixAutonomousFlag		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.7
The value to be placed in the Autonomous Flag field in the Prefix Information option.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfacePrefixSource		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.8
The source of this prefix. If configured by management the value will be configured(3). If determined automatically from IPv6 interface address configuration the value will be dynamic(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), dynamic(2), configured(3)

alaIPv6InterfacePrefixValidLifetimeDecrement		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.9
If true, use the remaining seconds derived from alaIPv6InterfacePrefixValidLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixValidLifetime.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfacePrefixValidLifetimeExpire		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.10
The date and time when the advertised prefix Valid Lifetime expires. To use this value, alaIPv6InterfaceValidLifetimeDecrement must be set to true.
Status: current	Access: read-create
OBJECT-TYPE
	DateAndTime

alaIPv6InterfacePrefixPreferredLifetimeDecrement		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.11
If true, use the remaining seconds derived from alaIPv6InterfacePrefixPreferredLifetime in the Router Advertisement. If false, use the static value alaIPv6InterfacePrefixPreferredLifetime.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6InterfacePrefixPreferredLifetimeExpire		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.9.1.12
The date and time when the advertised prefix Preferred Lifetime expires. To use this value, alaIPv6InterfacePreferredLifetimeDecrement must be set to true.
Status: current	Access: read-create
OBJECT-TYPE
	DateAndTime

alaIPv6PMTUTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10
Table allowing the retrieval of the known IPv6 path MTU value.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6PMTUEntry

alaIPv6PMTUEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1
An IPv6 path MTU entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6PMTUEntry

alaIPv6PMTUDest		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.1
The destination address of the IPv6 path.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

alaIPv6PMTU		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.2
The path's MTU.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

alaIPv6PMTUExpire		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.3
The minimum time remaining before the PMTU entry is removed from the table.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

alaIPv6PMTUHits		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.4
The number of times the path MTU entry has been used.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alaIPv6PMTUUpdates		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.10.1.5
The number of times the path MTU entry has been updated.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alaIPv6RouteFlagsTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11
Table allowing the retrieval of the flags for IPv6 route entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6RouteFlagsEntry

alaIPv6RouteFlagsEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1
An IPV6 route flags entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6RouteFlagsEntry

alaIPv6RouteFlagsUp		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.1
True if the Up (U) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsGateway		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.2
True if the Gateway (G) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsHost		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.3
True if the Host (H) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsStatic		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.4
True if the Static (S) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsCloneable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.5
True if the Cloneable (C) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsDiscard		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.6
True if the Discard/Blackhole (B) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsECMP		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.7
True if the ECMP (E) flag is set on the route.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6RouteFlagsTransient		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.11.1.8
True if route has not been replaced by valid route after takeover.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alaIPv6LocalUnicastTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13
Table allowing the creation and removal of local IPv6 unicast addresses (RFC 4193) on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6LocalUnicastEntry

alaIPv6LocalUnicastEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1
An local unicast IPv6 address entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6LocalUnicastEntry

alaIPv6LocalUnicastGlobalID		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.1
The global ID portion of the local IPv6 unicast address. Leave the value as all zero when adding a new addres to use the alaIPv6GlobalID value.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(5)

alaIPv6LocalUnicastSubnetID		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.2
The subnet ID portion of the local IPv6 unicast address.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(2)

alaIPv6LocalUnicastInterfaceID		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.3
The interface identifier portion of the local IPv6 unicast address. When alaIPv6LocalUnicastEUI64 is true(1) the value of this object should be all zero.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(8)

alaIPv6LocalUnicastPrefixLength		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.4
The number of bits that are significant in the IPv6 address prefix.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	64..128

alaIPv6LocalUnicastEUI64		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.5
If true(1) the interface identifier is formed from an automatically generated EUI-64 value.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alaIPv6LocalUnicastRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.13.1.6
Used to control the addition and removal of local IPv6 unicast addresses.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alaIPv6RAFilterTrustedTable		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14
Table allowing the creation and removal of trusted ports for an interface's RA filtering.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlaIPv6RAFilterTrustedEntry

alaIPv6RAFilterTrustedEntry		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1
An RA filter trusted port entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlaIPv6RAFilterTrustedEntry

alaIPv6RAFilterTrustedChassis		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.1
On a multi-chasis system, the chassis on which the trusted port resides. On a single-chassis system or when specifying a link aggregation this value is always 0.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

alaIPv6RAFilterTrustedSlot		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.2
The slot on which the trusted port resides. When specifying a link aggregation this value is always 0.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

alaIPv6RAFilterTrustedPort		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.3
The trusted port's physical port number or the id of a link aggregation.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

alaIPv6RAFilterTrustedRowStatus		1.3.6.1.4.1.6486.801.1.2.1.29.1.1.14.1.4
Used to control the addition and removal of an RA filter's trusted ports.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ndpMaxLimitReached		1.3.6.1.4.1.6486.801.1.2.1.29.1.0.1
This notification is generated when hardware table has reached supported Maximum entries. OS6400 will not generate new ARP request for new nexthops
Status: deprecated	Access: read-create
NOTIFICATION-TYPE

alaIPv6NeighborLimitExceeded		1.3.6.1.4.1.6486.801.1.2.1.29.1.0.2
Notification that the system-wide neighbor cache limit has been exceeded.
Status: current	Access: read-create
NOTIFICATION-TYPE

alaIPv6NeighborVRFLimitExceeded		1.3.6.1.4.1.6486.801.1.2.1.29.1.0.3
Notification that a per-VRF neighbor cache limit has been exceeded.
Status: current	Access: read-create
NOTIFICATION-TYPE

alaIPv6InterfaceNeighborLimitExceeded		1.3.6.1.4.1.6486.801.1.2.1.29.1.0.4
Notification that a per-interface neighbor cache limit has been exceeded.
Status: current	Access: read-create
NOTIFICATION-TYPE

alcatelIND1IPv6MIBConformance		1.3.6.1.4.1.6486.801.1.2.1.29.1.2
OBJECT IDENTIFIER

alcatelIND1IPv6MIBCompliances		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1
OBJECT IDENTIFIER

alcatelIND1IPv6MIBGroups		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2
OBJECT IDENTIFIER

alaIPv6Compliance		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.1.1
The compliance statement for switches with Alcatel IPv6 stack and implementing ALCATEL-IND1-IPV6-MIB.
Status: current	Access: read-create
MODULE-COMPLIANCE

alaIPv6TunnelConfigGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.1
A collection of objects to support management of Alcatel IPv6 tunneling.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6ConfigGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.2
A collection of objects to support management of configuration parameters of Alcatel IPv6 stack.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6NeighborGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.3
A collection of objects to support management of IPv6 neighbors.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6StaticRouteGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.4
A collection of objects to support management of IPv6 static routes.
Status: obsolete	Access: read-create
OBJECT-GROUP

alaIPv6InterfaceGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.5
A collection of objects to support management of IPv6 interfaces.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6InterfaceAddressGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.6
A collection of objects to support management of IPv6 addresses assigned to interfaces.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6InterfaceEUI64AddressGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.7
A collection of objects to support management of IPv6 EUI-64 addresses assigned to interfaces.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6InterfacePrefixGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.8
A collection of objects to support management of IPv6 prefixes assigned to interfaces.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6PMTUGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.9
A collection of objects to support management of IPv6 path MTUs.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6RouteFlagsGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.10
A collection of objects to support management of IPv6 route flags.
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6LocalUnicastGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.11
A collection of objects to support management of local IPv6 unicast addresses (RFC 4193).
Status: current	Access: read-create
OBJECT-GROUP

alaIPv6HostGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.12
A collection of objects to support management of IPv6 addresses assigned to Host.
Status: current	Access: read-create
OBJECT-GROUP

alcatelIND1IPv6NotificationGroup		1.3.6.1.4.1.6486.801.1.2.1.29.1.2.2.13
The AlcatelIND1IPv6 MIB Notification Group.
Status: current	Access: read-create
NOTIFICATION-GROUP