AH-TRAP-MIB

File: AH-TRAP-MIB.mib (40356 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC AH-SMI-MIB

Imported symbols

MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE
Integer32 TruthValue Counter32
DisplayString ahAPTrap AhString
AhNodeID AhMACProtocol

Defined Types

AhAuthenticationMethod  
Authentication method supported by the HiveAP
TEXTUAL-CONVENTION    
  INTEGER cwp(0), open(1), wep-open(2), wep-shared(3), wpa-psk(4), wpa2-psk(5), wpa-8021x(6), wpa2-8021X(7), wpa-auto-psk(8), dynamic-wep(10), x8021x(11)  

AhEncrytionMethod  
Encryption method supported by the HiveAP
TEXTUAL-CONVENTION    
  INTEGER aes(0), tkip(1), wep(2), non(3)  

AhState  
It defines the state for interfaces.
TEXTUAL-CONVENTION    
  INTEGER ahUp(1), ahDown(2)  

AhProbableCause  
It defines the probable cause for a problem on the HiveAP.
TEXTUAL-CONVENTION    
  INTEGER ahClear(0), ahUnknown(1), ahFlashFailure(2), ahFanFailure(3), ahPowerSupplyFailure(4), ahSoftwareUpgradeFailure(5), ahRadioFailure(6), ahConfFailure(7)  

Defined Values

ahTrapModule 1.3.6.1.4.1.26928.1.1.1.1.1
This is the MIB module for access point trap definitions for Aerohive Networks Inc.
MODULE-IDENTITY    

ahNotificationVarBind 1.3.6.1.4.1.26928.1.1.1.1.2
OBJECT IDENTIFIER    

ahFailureTrap 1.3.6.1.4.1.26928.1.1.1.1.1.1
This event is generated for any equipment or software failures.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahThresholdCrossingEvent 1.3.6.1.4.1.26928.1.1.1.1.1.2
This event is generated whenever a threshold is crossed for the first time.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahStateChangeEvent 1.3.6.1.4.1.26928.1.1.1.1.1.3
This event is generated whenever an object state change occurs.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahConnectionChangeEvent 1.3.6.1.4.1.26928.1.1.1.1.1.4
This event is generated whenever a connection state change occurs. The connection might be between a HiveAP and its client, or between a HiveAP and a neighboring HiveAP.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahIDPStationEvent 1.3.6.1.4.1.26928.1.1.1.1.1.5
This event is generated whenever IDP detects an AP in its neighborhood. The ahRomoteId indicates the detected AP MAC address, and the ahIDPCompliance indicates conformance of IDP policy this AP satisfies. The ahIDPChannel and ahIDPRSSI indicates the radio channel and Receive Signal Strenth Indication.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahClientInfoEvent 1.3.6.1.4.1.26928.1.1.1.1.1.6
This event is generated whenever HiveAP a new client makes an association and its IP address, hostname, and User name is obtained.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahPoEEvent 1.3.6.1.4.1.26928.1.1.1.1.1.7
This event is generated whenever a HiveAP (802.11n product line) boots up or changes power levels.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahChannelPowerChangeEvent 1.3.6.1.4.1.26928.1.1.1.1.1.8
This event is generated whenever a HiveAP boots up, or changes channels or power levels.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahIDPMitigateEvent 1.3.6.1.4.1.26928.1.1.1.1.1.9
This event is generated whenever IDP detects an rogue client connect to a rogue AP. The ahRomoteId indicates the detected Station MAC address.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahInterferenceMapAlertEvent 1.3.6.1.4.1.26928.1.1.1.1.1.10
For every one minute interval, AP will monitor the interference channel utilizations (snapshot, short term means average and running average) and CRC error rate against their thresholds, if any one of them is above their threshold (thresholds are settable by CLI), AP should send HM an interference alert event to HM. AP will send out clear alert to HM only when: the last short term period s CRC-error-rate, means average Interference CU and the last snapshot interference CU are all below their thresholds.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahBandwidthSentinelEvent 1.3.6.1.4.1.26928.1.1.1.1.1.11
HiveOS will send two different kinds of traps: bandwidth sentinel alert trap, and bandwidth sentinel clear trap. The alert trap will serve the purpose to tell HM that the client is violating the bandwidth sentinel, the clear trap will clear the previous alert trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahAlarmMsgMapAlertEvent 1.3.6.1.4.1.26928.1.1.1.1.1.12
HiveOS will send two different kinds of level alert: interface level alert, and client level alert. There are four alert types, CRC error rate, TX drop/retry rate, Rx drop rate; interface level includes all alert type, the client level includes Tx drop/retry rate, Rx drop Rate; the 'set' alert means there is an alert raised, with type indicated in the alert type field, the 'clear' alert means the previous alert condition has been cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

ahAPId 1.3.6.1.4.1.26928.1.1.1.1.2.1
It is the node ID (MAC address in hexadecimal format) of the HiveAP where the trap is generated. If a HiveAP is configured with 2 hives, the node ID is the first MAC address of the management interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhNodeID  

ahAPName 1.3.6.1.4.1.26928.1.1.1.1.2.2
The host name of the HiveAP where the trap is generated.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhString  

ahSeverity 1.3.6.1.4.1.26928.1.1.1.1.2.3
It contains the serverity of the trap.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER critical(5), major(4), minor(3), info(2), undetermined(1)  

ahObjectName 1.3.6.1.4.1.26928.1.1.1.1.2.4
It describes the object for which the trap is generated.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..64)  

ahProbableCause 1.3.6.1.4.1.26928.1.1.1.1.2.5
It describes the probable cause of a problem.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhProbableCause  

ahCurValue 1.3.6.1.4.1.26928.1.1.1.1.2.6
It contains the current value of a threshold counter.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ahThresholdHigh 1.3.6.1.4.1.26928.1.1.1.1.2.7
It contains the value for a high threshold.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ahThresholdLow 1.3.6.1.4.1.26928.1.1.1.1.2.8
It contains the value for a low threshold.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ahPreviousState 1.3.6.1.4.1.26928.1.1.1.1.2.9
It contains the value for a previous state.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhState  

ahCurrentState 1.3.6.1.4.1.26928.1.1.1.1.2.10
It contains the value for the current state.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhState  

ahTrapDesc 1.3.6.1.4.1.26928.1.1.1.1.2.11
It contains the description of the trap.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

ahCode 1.3.6.1.4.1.26928.1.1.1.1.2.12
It contains access information to the Aerohive logging/action dictionary.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

ahIfIndex 1.3.6.1.4.1.26928.1.1.1.1.2.13
The interface index used to identify uniquely an interface (logical or physical).
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

ahObjectType 1.3.6.1.4.1.26928.1.1.1.1.2.14
It specifies the object type: a client link or a neighbor link.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER clientLink(1), neighborLink(2)  

ahRemoteId 1.3.6.1.4.1.26928.1.1.1.1.2.15
It is the MAC address of the remote node. If the remote node is a HiveAP, the ID must be the MAC address of its management interface. If the remote node is a client station, it must be the MAC address of the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhNodeID  

ahIDPType 1.3.6.1.4.1.26928.1.1.1.1.2.16
It is used to indicate the AP identified is a rogue, or valid, or compliant, or noncompliant, or external AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER rogue(1), valid(2), external(3)  

ahIDPChannel 1.3.6.1.4.1.26928.1.1.1.1.2.17
It is the channel number used by the identified AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

ahIDPRSSI 1.3.6.1.4.1.26928.1.1.1.1.2.18
It is the RSSI for the identified AP or Client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

ahIDPCompliance 1.3.6.1.4.1.26928.1.1.1.1.2.19
It is bit mask to indicate which policy the indentified AP is compliant with (bit is set if it is NOT compliant).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER open-policy(1), wep-policy(2), wpa-policy(4), wmm-policy(8), oui-policy(16), ssid-policy(32), short-preamble-policy(64), short-beacon-policy(128), ad-hoc-policy(256)  

ahSSID 1.3.6.1.4.1.26928.1.1.1.1.2.20
It contains the SSID name for the detected AP.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(0..32)  

ahStationType 1.3.6.1.4.1.26928.1.1.1.1.2.21
It indicates whether it is event for a peer AP or client PC
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER station-ap(1), station-client(2)  

ahIDPStationData 1.3.6.1.4.1.26928.1.1.1.1.2.22
It is bit mask to indicate policies are detected for the identified AP . Note: the oui-policy and ssid-policy are omitted due to the presence of the ahRemoteID, and SSID in the trap message.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER open-policy(1), wep-policy(2), wpa-policy(4), wmm-policy(8), short-preamble-policy(64), short-beacon-policy(128), ad-hoc-policy(256)  

ahRemoved 1.3.6.1.4.1.26928.1.1.1.1.2.23
It indicates whether the AP or client can not be detected.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER removed-false(0), removed-true(1)  

ahClientMAC 1.3.6.1.4.1.26928.1.1.1.1.2.24
It contains the MAC address of the wireless client. It is required.
Status: current Access: not-accessible
OBJECT-TYPE    
  AhNodeID  

ahCLientIP 1.3.6.1.4.1.26928.1.1.1.1.2.25
It contains the IP address of the wireless client. It is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

ahClientHostName 1.3.6.1.4.1.26928.1.1.1.1.2.26
It contains the host name of the wireless client. It is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

ahClientUserName 1.3.6.1.4.1.26928.1.1.1.1.2.27
It contains the user name of the wireless client. It is optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

ahPowerSrc 1.3.6.1.4.1.26928.1.1.1.1.2.28
It indicates whether the power source is from the power adaptor or PoE. If the power source is the adaptor, PoE information in the trap is ignored.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER adaptor(0), poe(1)  

ahPoEEth0On 1.3.6.1.4.1.26928.1.1.1.1.2.29
It indicates whether PoE is on eth0 or not.
Status: current Access: not-accessible
OBJECT-TYPE    
  TruthValue  

ahPoEEth0Pwr 1.3.6.1.4.1.26928.1.1.1.1.2.30
It indicates the power level of PoE in watts multiply by 10.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ahPoEEth1On 1.3.6.1.4.1.26928.1.1.1.1.2.31
It indicates whether PoE is on eth1 or not.
Status: current Access: not-accessible
OBJECT-TYPE    
  TruthValue  

ahPoEEth1Pwr 1.3.6.1.4.1.26928.1.1.1.1.2.32
It indicates the power level of PoE on eht1 in watts multiply by 10.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ahRadioChannel 1.3.6.1.4.1.26928.1.1.1.1.2.33
It is the channel number currently in use for this radio.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ahRadioTxPower 1.3.6.1.4.1.26928.1.1.1.1.2.34
It is the transmit power in dBm that the radio is currently using. The range is 0 to 20 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ahClientAuthMethod 1.3.6.1.4.1.26928.1.1.1.1.2.35
It is the authentication method the client uses when communicating with the HiveAP.
Status: current Access: read-only
OBJECT-TYPE    
  AhAuthenticationMethod  

ahClientEncryptionMethod 1.3.6.1.4.1.26928.1.1.1.1.2.36
It is the encryption method the client uses when communicating with the HiveAP.
Status: current Access: read-only
OBJECT-TYPE    
  AhEncrytionMethod  

ahClientMACProtocol 1.3.6.1.4.1.26928.1.1.1.1.2.37
It is the radio mode the client uses when communicating with the HiveAP.
Status: current Access: read-only
OBJECT-TYPE    
  AhMACProtocol  

ahClientVLAN 1.3.6.1.4.1.26928.1.1.1.1.2.38
It is the VLAN that the client uses when communicating with the HiveAP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ahClientUserProfId 1.3.6.1.4.1.26928.1.1.1.1.2.39
It is the user profile ID that the client uses when communicating with the HiveAP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ahClientChannel 1.3.6.1.4.1.26928.1.1.1.1.2.40
It is the radio channel that the client uses when communicating with the HiveAP.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ahClientCWPUsed 1.3.6.1.4.1.26928.1.1.1.1.2.41
It is the Boolean datatype indicating whether a captive web portal is used.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ahBSSID 1.3.6.1.4.1.26928.1.1.1.1.2.42
It is the basic service set identifier of the client if the ahRemoteId is a client.
Status: current Access: read-only
OBJECT-TYPE    
  AhNodeID  

ahPoEEth0MaxSpeed 1.3.6.1.4.1.26928.1.1.1.1.2.43
It is the automatically adjusted maximum Ethernet speed based on the power source and level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER linkdown(1), eth10(2), eth100(3), eth1000(4)  

ahPoEEth1MaxSpeed 1.3.6.1.4.1.26928.1.1.1.1.2.44
It is the automatically adjusted maximum Ethernet speed based on the power source and level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER linkdown(1), eth10(2), eth100(3), eth1000(4)  

ahPoEWifi0Setting 1.3.6.1.4.1.26928.1.1.1.1.2.45
It is the automatically adjusted Wi-Fi setting based on the power source and power level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), linkdown(1), config(2), tx2rx3(3)  

ahPoEWifi1Setting 1.3.6.1.4.1.26928.1.1.1.1.2.46
It is the automatically adjusted Wi-Fi setting based on the power source and power level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), linkdown(1), config(2), tx2rx3(3)  

ahPoEWifi2Setting 1.3.6.1.4.1.26928.1.1.1.1.2.47
It is the automatically adjusted Wi-Fi setting based on the power source and power level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), linkdown(1), config(2), tx2rx3(3)  

ahAssociationTime 1.3.6.1.4.1.26928.1.1.1.1.2.48
The association time(s) of client connect or disconnect to AP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ahIDPInNet 1.3.6.1.4.1.26928.1.1.1.1.2.49
It is the Boolean datatype indicating whether AP is in local network.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ahDiscoverAge 1.3.6.1.4.1.26928.1.1.1.1.2.50
It is the age from the rogue client is discovered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ahUpdateAge 1.3.6.1.4.1.26928.1.1.1.1.2.51
It is the age from the rogue client is updated.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ahRunningAverageInterference 1.3.6.1.4.1.26928.1.1.1.1.2.52
channel utilizations running average interference.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahShortTermInterference 1.3.6.1.4.1.26928.1.1.1.1.2.53
channel utilizations short term interference. The short term period is defined by CLI config, usually, it should be in the range of 5 minutes to 30 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahSnapshotInterference 1.3.6.1.4.1.26928.1.1.1.1.2.54
channel utilizations snapshot interference. it is the last minute s means average.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahFailureSet 1.3.6.1.4.1.26928.1.1.1.1.2.55
It is the Boolean datatype indicating whether this failure(alert) is on or off.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ahInterferenceThreshold 1.3.6.1.4.1.26928.1.1.1.1.2.56
the configured channel utilizations interference threshold. it is defined by CLI config.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahCRCErrRateThreshold 1.3.6.1.4.1.26928.1.1.1.1.2.57
the configured CRC error rate threshold. it is defined by CLI config.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahCRCErrRate 1.3.6.1.4.1.26928.1.1.1.1.2.58
short term CRC error rate. The interval of the refresh of CRC error rate calculation is the same interval as channel utilization short term means average interval.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahBandwidthSentinelStatus 1.3.6.1.4.1.26928.1.1.1.1.2.59
Bandwidth sentinel status. In alert message, the value should be zero. In clear message, the value should be 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER alert(0), clear(1), bad(2)  

ahGuaranteedBandwidth 1.3.6.1.4.1.26928.1.1.1.1.2.60
the configured guaranteed bandwidth(Kbps). it is defined by CLI config.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahActualBandwidth 1.3.6.1.4.1.26928.1.1.1.1.2.61
the actual bandwidth(Kbps).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahBandwidthSentinelAction 1.3.6.1.4.1.26928.1.1.1.1.2.62
bit maps to indicate which action has been taken on this client. bit 0: indicate whether log the guaranteed bandwidth violation or not, bit 1: indicate whether add more token to meet the minimum guaranteed bandwidth or not.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ahBeaconInterval 1.3.6.1.4.1.26928.1.1.1.1.2.63
It is the number of time units between Beacon transmissions, One time unit is 1024 microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ahLevel 1.3.6.1.4.1.26928.1.1.1.1.2.64
The level value will tell HM whether this is an interface level alert or a client alert.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER interface(1), client(2)  

ahAlarmAlertType 1.3.6.1.4.1.26928.1.1.1.1.2.65
There are five types, CRC Rate only applies to interface level alert, TX drop/retry rate is is calculated based on retries over total unicast TX frames, RX drop rate is calculated based on the dropped RX frames over total RX frames, Airtime percentage is the sum of both TX and RX airtime percentages.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER crcrate(0), txdroprate(1), txretryrate(2), rxdroprate(3), airtime(4)  

ahThresholdValue 1.3.6.1.4.1.26928.1.1.1.1.2.66
the configured CRC error rate, TX drop/retry rate, RX drop rate threshold. it is defined by CLI config.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahShortTermValue 1.3.6.1.4.1.26928.1.1.1.1.2.67
the percentage of this sampling period, CRC error rate, TX drop/retry rate, RX drop rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahSnapshotValue 1.3.6.1.4.1.26928.1.1.1.1.2.68
the snapshot value of CRC error rate, TX drop/retry rate, RX drop rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ahIfName 1.3.6.1.4.1.26928.1.1.1.1.2.69
Name - uniquely identifies an AP Interface.
Status: current Access: read-only
OBJECT-TYPE    
  AhString