AGENT-GENERAL-MIB

File: AGENT-GENERAL-MIB.mib (135931 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1213-MIB
INET-ADDRESS-MIB DLINK-ID-REC-MIB Q-BRIDGE-MIB

Imported symbols

IpAddress MODULE-IDENTITY OBJECT-TYPE
Integer32 TruthValue RowStatus
MacAddress DisplayString InetAddressType
InetAddress AgentNotifyLevel dlink-common-mgmt
VlanId

Defined Types

Ipv6Address  
This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

UnitList  
OCTET STRING Size(0..3)    

AgentMibCapabilityEntry  
SEQUENCE    
  agentMibCapabilityIndex Integer32
  agentMibCapabilityDescr DisplayString
  agentMibCapabilityVersion Integer32
  agentMibCapabilityType INTEGER

AgentPORTutilizationEntry  
SEQUENCE    
  agentPORTutilizationProtIndex INTEGER
  agentPORTutilizationTX INTEGER
  agentPORTutilizationRX INTEGER
  agentPORTutilizationUtil INTEGER

AgentDRAMutilizationEntry  
SEQUENCE    
  agentDRAMutilizationUnitID INTEGER
  agentDRAMutilizationTotalDRAM INTEGER
  agentDRAMutilizationUsedDRAM INTEGER
  agentDRAMutilization INTEGER

AgentFLASHutilizationEntry  
SEQUENCE    
  agentFLASHutilizationUnitID INTEGER
  agentFLASHutilizationTotalFLASH INTEGER
  agentFLASHutilizationUsedFLASH INTEGER
  agentFLASHutilization INTEGER

AgentBscSwFileEntry  
SEQUENCE    
  agentBscSwFileIndex Integer32
  agentBscSwFileDscr DisplayString
  agentBscSwFileAddr IpAddress
  agentBscSwFileTransferType INTEGER
  agentBscSwFile DisplayString
  agentBscSwFileLocateId INTEGER
  agentBscSwFileLoadType INTEGER
  agentBscSwFileCtrl INTEGER
  agentBscSwFileBIncrement TruthValue
  agentBscSwFileCtrlID INTEGER
  agentBscSwFileCtrlUnitID UnitList
  agentBscSwFileIPv6Addr Ipv6Address
  agentBscSwFileBootUpImage TruthValue
  agentBscSwFileForceAgree TruthValue
  agentBscSwFileInterfaceName DisplayString
  agentBscSwFileServerDomainName DisplayString

SwMultiImageInfoEntry  
SEQUENCE    
  swMultiImageInfoID INTEGER
  swMultiImageVersion DisplayString
  swMultiImageSize Integer32
  swMultiImageUpdateTime DisplayString
  swMultiImageFrom DisplayString
  swMultiImageSendUser DisplayString
  swMultiImageFileName DisplayString

SwMultiCfgInfoEntry  
SEQUENCE    
  swMultiCfgInfoID INTEGER
  swMultiCfgVersion DisplayString
  swMultiCfgSize Integer32
  swMultiCFgUpdateTime DisplayString
  swMultiCfgFrom DisplayString
  swMultiCfgSendUser DisplayString
  swMultiCfgFileName DisplayString

SwMultiCfgCtrlEntry  
SEQUENCE    
  swMultiCfgCtrlID INTEGER
  swMultiCfgAction INTEGER

AgentTrustedHostEntry  
SEQUENCE    
  agentTrustedHostIndex INTEGER
  agentTrustedHostIPAddress IpAddress
  agentTrustedHostRowStatus RowStatus
  agentTrustedHostIPSubnetMask IpAddress
  agentTrustedHostForSNMP INTEGER
  agentTrustedHostForTELNET INTEGER
  agentTrustedHostForSSH INTEGER
  agentTrustedHostForHTTP INTEGER
  agentTrustedHostForHTTPS INTEGER
  agentTrustedHostForPING INTEGER
  agentTrustedHostAddrType InetAddressType
  agentTrustedHostAddr InetAddress
  agentTrustedHostIPv6PrefixLen INTEGER

AgentFDBClearByPortEntry  
SEQUENCE    
  agentFDBClearPortIndex INTEGER
  agentFDBClearByPortAction INTEGER

AgentFDBClearByVlanEntry  
SEQUENCE    
  agentFDBClearVid VlanId
  agentFDBClearByVlanAction INTEGER

AgentFDBSecurityEntry  
SEQUENCE    
  agentFDBVid VlanId
  agentFDBMacAddress MacAddress
  agentFDBPort INTEGER
  agentFDBType INTEGER
  agentFDBStatus INTEGER
  agentFDBSecurityModule INTEGER

AgentGratuitousARPEntry  
SEQUENCE    
  agentGratuitousARPInterfaceName DisplayString
  agentGratuitousARPPeriodicalSendInterval INTEGER
  agentGratuitousARPTrapState INTEGER
  agentGratuitousARPLogState INTEGER

SwMultiImageCtrlEntry  
SEQUENCE    
  swMultiImageCtrlID INTEGER
  swMultiImageCtrlAction INTEGER

AgentBscFileSystemEntry  
SEQUENCE    
  agentBscFileSystemIndex Integer32
  agentBscFileSystemDscr DisplayString
  agentBscFileSystemServerAddr IpAddress
  agentBscFileSystemServerIPv6Addr Ipv6Address
  agentBscFileSystemServerFileName DisplayString
  agentBscFileSystemDeviceDriverID INTEGER
  agentBscFileSystemDeviceFileName DisplayString
  agentBscFileSystemLoadType INTEGER
  agentBscFileSystemCtrlUnitID UnitList
  agentBscFileSystemBootUpImage TruthValue
  agentBscFileSystemForceAgree TruthValue
  agentBscFileSystemCtrl INTEGER
  agentBscFileSystemInterfaceName DisplayString
  agentBscFileSystemServerDomainName DisplayString
  agentBscFileSystemIncrement TruthValue

AgentFileSystemConfigEntry  
SEQUENCE    
  agentFileSystemUnit Integer32
  agentFileSystemDriverID INTEGER
  agentFileSystemBootImage DisplayString
  agentFileSystemBootConfig DisplayString
  agentFileSystemActConfig DisplayString

AgentFTPFileEntry  
SEQUENCE    
  agentFTPFileIndex Integer32
  agentFTPFileDscr DisplayString
  agentFTPFileLoadType INTEGER
  agentFTPFileAddr IpAddress
  agentFTPTCPPort INTEGER
  agentFTPFileName DisplayString
  agentFTPUserName DisplayString
  agentFTPPassword DisplayString
  agentFTPFileCtrlID INTEGER
  agentFTPFileBIncrement TruthValue
  agentFTPFileCtrl INTEGER
  agentFTPFileBootUpImage TruthValue
  agentFTPFileForceAgree TruthValue
  agentFTPFileIPv6Addr DisplayString
  agentFTPFileInterfaceName DisplayString
  agentFTPFileUnitID UnitList

AgentFTPFileSystemEntry  
SEQUENCE    
  agentFTPFileSystemIndex Integer32
  agentFTPFileSystemDscr DisplayString
  agentFTPFileSystemLoadType INTEGER
  agentFTPFileSystemAddressType InetAddressType
  agentFTPFileSystemAddress InetAddress
  agentFTPFileSystemTCPPort INTEGER
  agentFTPFileSystemServerFileName DisplayString
  agentFTPFileSystemDeviceFileName DisplayString
  agentFTPFileSystemUserName DisplayString
  agentFTPFileSystemPassword DisplayString
  agentFTPFileSystemCtrlUnitID UnitList
  agentFTPFileSystemBootUpImage TruthValue
  agentFTPFileSystemCtrl INTEGER

AgentTrapManagerEntry  
SEQUENCE    
  agentTrapManagerIndex INTEGER
  agentTrapManagerIpAddr IpAddress
  agentTrapManagerComm DisplayString
  agentTrapManagerMsgVer INTEGER
  agentTrapManagerStatus INTEGER

Defined Values

agentGeneralMgmt 1.3.6.1.4.1.171.12.1
The structure of general management information for enterprise.
MODULE-IDENTITY    

agentBasicInfo 1.3.6.1.4.1.171.12.1.1
OBJECT IDENTIFIER    

agentMgmtProtocolCapability 1.3.6.1.4.1.171.12.1.1.1
The network management protocol(s) supported by this agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), snmp-ip(2), snmp-ipx(3), snmp-ip-ipx(4)  

agentMibCapabilityTable 1.3.6.1.4.1.171.12.1.1.2
A list of MIB capability entries supported by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentMibCapabilityEntry

agentMibCapabilityEntry 1.3.6.1.4.1.171.12.1.1.2.1
A MIB capability entry containing objects that describe a particular MIB supported by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentMibCapabilityEntry  

agentMibCapabilityIndex 1.3.6.1.4.1.171.12.1.1.2.1.1
A list of Agent MIB Capability Description entries.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentMibCapabilityDescr 1.3.6.1.4.1.171.12.1.1.2.1.2
The name of the MIB supported by the agent.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..35)  

agentMibCapabilityVersion 1.3.6.1.4.1.171.12.1.1.2.1.3
The version of the MIB specified in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentMibCapabilityType 1.3.6.1.4.1.171.12.1.1.2.1.4
The type of MIB specified in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), standard(2), proprietary(3), experiment(4)  

agentStatusConsoleInUse 1.3.6.1.4.1.171.12.1.1.3
This indicates whether the console is currently in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), in-use(2), not-in-use(3)  

agentStatusSaveCfg 1.3.6.1.4.1.171.12.1.1.4
This indicates the status of the device configuration. other (1) - This entry is currently in use but the conditions under which it will remain so are determined by each of the following values. proceeding (2) - The device configuration is currently being saved into NV-RAM. completed (3) - All of the device configuration parameters have been saved into NV-RAM. failed (4) - The process to save the device configuration has failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), proceeding(2), completed(3), failed(4)  

agentStatusFileTransfer 1.3.6.1.4.1.171.12.1.1.5
The status of the firmware download control. If the value is stated as 'other', the firmware has not been updated since the device was started.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), in-process(2), invalid-file(3), violation(4), file-not-found(5), disk-full(6), complete(7), time-out(8), not-format(9), memory-full(10)  

agentCPUutilization 1.3.6.1.4.1.171.12.1.1.6
OBJECT IDENTIFIER    

agentCPUutilizationIn5sec 1.3.6.1.4.1.171.12.1.1.6.1
The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentCPUutilizationIn1min 1.3.6.1.4.1.171.12.1.1.6.2
The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentCPUutilizationIn5min 1.3.6.1.4.1.171.12.1.1.6.3
The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentDualImageStatus 1.3.6.1.4.1.171.12.1.1.7
The dual image status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER not-supported(0), supported(1)  

agentPORTutilizationTable 1.3.6.1.4.1.171.12.1.1.8
This table specifies the current utilization of a specified port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentPORTutilizationEntry

agentPORTutilizationEntry 1.3.6.1.4.1.171.12.1.1.8.1
A list of information regarding the port utilization function.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentPORTutilizationEntry  

agentPORTutilizationProtIndex 1.3.6.1.4.1.171.12.1.1.8.1.1
This object indicates the module's port number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

agentPORTutilizationTX 1.3.6.1.4.1.171.12.1.1.8.1.2
The current rate of transmitted frames on the specified port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentPORTutilizationRX 1.3.6.1.4.1.171.12.1.1.8.1.3
The current rate of received frames on the specified port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentPORTutilizationUtil 1.3.6.1.4.1.171.12.1.1.8.1.4
The current percentages regarding port statistics.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

agentDRAMutilizationTable 1.3.6.1.4.1.171.12.1.1.9
Information about DRAM memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentDRAMutilizationEntry

agentDRAMutilizationEntry 1.3.6.1.4.1.171.12.1.1.9.1
A list of information about DRAM memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentDRAMutilizationEntry  

agentDRAMutilizationUnitID 1.3.6.1.4.1.171.12.1.1.9.1.1
Specifies the unit ID. If the ID equals zero, it means the current device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentDRAMutilizationTotalDRAM 1.3.6.1.4.1.171.12.1.1.9.1.2
The size of total DRAM memory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentDRAMutilizationUsedDRAM 1.3.6.1.4.1.171.12.1.1.9.1.3
The size of used DRAM memory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentDRAMutilization 1.3.6.1.4.1.171.12.1.1.9.1.4
The percentage of used DRAM memory of the total DRAM memory available. The value will be between 0% (idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentFLASHutilizationTable 1.3.6.1.4.1.171.12.1.1.10
Information about the flash memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFLASHutilizationEntry

agentFLASHutilizationEntry 1.3.6.1.4.1.171.12.1.1.10.1
Information about the flash memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFLASHutilizationEntry  

agentFLASHutilizationUnitID 1.3.6.1.4.1.171.12.1.1.10.1.1
Specifies the unit ID. If the ID equals zero, it means the current device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentFLASHutilizationTotalFLASH 1.3.6.1.4.1.171.12.1.1.10.1.2
The total size of flash memory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentFLASHutilizationUsedFLASH 1.3.6.1.4.1.171.12.1.1.10.1.3
The size of the used flash memory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentFLASHutilization 1.3.6.1.4.1.171.12.1.1.10.1.4
The percentage of used flash memory in total flash memory. The value will be between 0% (idle) and 100% (very busy).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentStatusReset 1.3.6.1.4.1.171.12.1.1.11
This indicates the status of 'agentReset'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER proceeding(1), completed(2), failed(3)  

agentSerialNumber 1.3.6.1.4.1.171.12.1.1.12
A text string containing the serial number of this device.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentFirmwareType 1.3.6.1.4.1.171.12.1.1.13
A text string containing the firmware type.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentBasicConfig 1.3.6.1.4.1.171.12.1.2
OBJECT IDENTIFIER    

agentBscSwFileTable 1.3.6.1.4.1.171.12.1.2.1
A list of MIB Basic Config entry support files updated by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentBscSwFileEntry

agentBscSwFileEntry 1.3.6.1.4.1.171.12.1.2.1.1
A basic configuration entry containing the objects that describe a particular MIB supported by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentBscSwFileEntry  

agentBscSwFileIndex 1.3.6.1.4.1.171.12.1.2.1.1.1
The table index for the file entry
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentBscSwFileDscr 1.3.6.1.4.1.171.12.1.2.1.1.2
The description of the software file purpose in this entry. Note: For systems that do not support a change to this object, setting a value for this object will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscSwFileAddr 1.3.6.1.4.1.171.12.1.2.1.1.3
The IP address where the file that needs to be downloaded is located, or the IP address where the file will be uploaded to.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentBscSwFileTransferType 1.3.6.1.4.1.171.12.1.2.1.1.4
The channel through which the file will be downloaded or uploaded. Note: For systems that do not support all channels, setting a value to the unsupported channel will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), network-load(2), out-of-band-load(3)  

agentBscSwFile 1.3.6.1.4.1.171.12.1.2.1.1.5
The name of the file to be downloaded from, or uploaded to, the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

agentBscSwFileLocateId 1.3.6.1.4.1.171.12.1.2.1.1.6
This object describes the type of file. runtime-code (1), log-file (2), cfg-file (3) Note: For systems that do not support changes to this object, setting a value for this object will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

agentBscSwFileLoadType 1.3.6.1.4.1.171.12.1.2.1.1.7
This object provides the user with a choice of uploading or downloading the selected file. Note: For systems that do not support a change to this object, setting a value for this object will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

agentBscSwFileCtrl 1.3.6.1.4.1.171.12.1.2.1.1.8
This object gives the user the option of downloading runtime software. This setting will take effect when the system restarts. See Note (1) below Note: For systems that do not support changes to this object, setting a value to this object will cause the system to return bad-value error messages. start - Activate firmware. delete (4) - Delete the firmware by indicated firmware ID. config-as-bootup (5) - Configured as bootup firmware by the indicated firmware(ID). apply (6) - Apply the configuration to be the active configuration by the indicated config ID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), inactive(2), start(3), delete(4), config-as-bootup(5), apply(6)  

agentBscSwFileBIncrement 1.3.6.1.4.1.171.12.1.2.1.1.9
This object indicates whether the previous configuration will remain valid or not after downloading the configuration file. True: Keep valid False: Erase.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentBscSwFileCtrlID 1.3.6.1.4.1.171.12.1.2.1.1.10
The section ID of the firmware image or configuration file. A value of 0 indicates the boot-up firmware image or configuration file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

agentBscSwFileCtrlUnitID 1.3.6.1.4.1.171.12.1.2.1.1.11
Specifies which unit of the switch stack the firmware image will be downloaded from. One or more units can be set in this list. Each bit from the left to the right represents the switch from unit ID 1 to unit ID 12. A null entry in this field denotes all switches in the switch stack.
Status: current Access: read-write
OBJECT-TYPE    
  UnitList  

agentBscSwFileIPv6Addr 1.3.6.1.4.1.171.12.1.2.1.1.12
The IPv6 address where the file will be downloaded from or uploaded to.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

agentBscSwFileBootUpImage 1.3.6.1.4.1.171.12.1.2.1.1.13
The result of the download will depend on whether the boot_up option is specified. Case 1: In the case where the master unit provides the file system and the slave unit does not provide the file system, when boot_up is specified, the file will be downloaded to the boot_up image on the slave. If boot_up is not specified, then the file will not be downloaded to this slave unit. Case 2: In the case where the master unit does not provide the file system and the slave unit provides the file system, when boot_up is specified, the file will be downloaded to the boot_up image on the slave unit. If boot_up is not specified, the file will not be downloaded to this slave unit. Case 3: In the case where the master unit and the slave unit both support or do not support the file system, the file will be downloaded to the specified file on the slave unit. If boot_up is specified, the downloaded file will be assigned as the boot_up image. True: boot_up option is specified. False: boot_up option is not specified.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentBscSwFileForceAgree 1.3.6.1.4.1.171.12.1.2.1.1.14
When the force_agree option is specified, the reboot command will be executed immediately, without any further confirmation from the user. True: force_agree option is specified. False: force_agree option is not specified.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentBscSwFileInterfaceName 1.3.6.1.4.1.171.12.1.2.1.1.15
This node is used to specify the interface name when the agentBscSwFileIPv6Addr is the link local address.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

agentBscSwFileServerDomainName 1.3.6.1.4.1.171.12.1.2.1.1.16
This object indicates the domain name of the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

agentFileTransfer 1.3.6.1.4.1.171.12.1.2.2
This object will execute the download or upload action. If start (2) is chosen, it will begin to download/upload and no reset will follow. If start-and-reset (3) is chosen, then the reset will be activated after completing the download or upload. No action if noaction (4) is chosen. Note: Because these functions will be limited by the support for the system in question, some of the selected items will be invalid. When the user selects an invalid entry, the system will respond with a bad-value status.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2), start-and-reset(3), noaction(4)  

agentSystemReset 1.3.6.1.4.1.171.12.1.2.3
This object indicates the agent system reset state. Setting this object to no-reset (4) has no effect. Setting this object to cold-start (2) or warm-start (3) will reset the agent. The agent always returns to no-reset (4) when this object is read. This object is replaced by 'agentReset'.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER other(1), cold-start(2), warm-start(3), no-reset(4)  

agentRs232PortConfig 1.3.6.1.4.1.171.12.1.2.4
This object indicates the RS-232C mode once the device has restarted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), console(2), out-of-band(3), notAvail(4)  

agentOutOfBandBaudRateConfig 1.3.6.1.4.1.171.12.1.2.5
This object allows the user to specify an out-of-band baud rate, which will take effect upon system restart. Note: Because these functions will be limited by the support for the system in question, some of the selected items will be invalid. When the user selects an invalid entry, the system will respond with a bad-value error message.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER other(1), baudRate-2400(2), baudRate-9600(3), baudRate-19200(4), baudRate-38400(5), baudRate-115200(6)  

agentSaveCfg 1.3.6.1.4.1.171.12.1.2.6
This object indicates the type of save command to be executed, when saving to NV-RAM. other (1) - None of the following. cfg-id1 (2) - Save configuration ID1. cfg-id2 (3)- Save configuration ID2. log (4) - Save log. all (5) - Save both (active configuration and log).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), cfg-id1(2), cfg-id2(3), log(4), all(5)  

swMultiImageInfoTable 1.3.6.1.4.1.171.12.1.2.7
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMultiImageInfoEntry

swMultiImageInfoEntry 1.3.6.1.4.1.171.12.1.2.7.1
A list of information about multiple image management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMultiImageInfoEntry  

swMultiImageInfoID 1.3.6.1.4.1.171.12.1.2.7.1.1
The stacking section ID of the firmware image. The stacking section ID = 256 * Unit ID + Image File ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swMultiImageVersion 1.3.6.1.4.1.171.12.1.2.7.1.2
The recorded downloaded firmware version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiImageSize 1.3.6.1.4.1.171.12.1.2.7.1.3
The recorded downloaded firmware size.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swMultiImageUpdateTime 1.3.6.1.4.1.171.12.1.2.7.1.4
The recorded firmware update time.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiImageFrom 1.3.6.1.4.1.171.12.1.2.7.1.5
The recorded IP address of the TFTP server
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

swMultiImageSendUser 1.3.6.1.4.1.171.12.1.2.7.1.6
The record of the user who downloaded the firmware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiImageFileName 1.3.6.1.4.1.171.12.1.2.7.1.7
When the system is set to boot from SD card, this object will display the recorded path name of the boot firmware file.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

agentMultiCfgMgmt 1.3.6.1.4.1.171.12.1.2.8
OBJECT IDENTIFIER    

swMultiCfgInfoTable 1.3.6.1.4.1.171.12.1.2.8.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMultiCfgInfoEntry

swMultiCfgInfoEntry 1.3.6.1.4.1.171.12.1.2.8.1.1
A list of information about multiple configuration files.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMultiCfgInfoEntry  

swMultiCfgInfoID 1.3.6.1.4.1.171.12.1.2.8.1.1.1
The section ID of the configuration files.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swMultiCfgVersion 1.3.6.1.4.1.171.12.1.2.8.1.1.2
The recorded downloaded configuration version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiCfgSize 1.3.6.1.4.1.171.12.1.2.8.1.1.3
The recorded downloaded configuration size (in bytes).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

swMultiCFgUpdateTime 1.3.6.1.4.1.171.12.1.2.8.1.1.4
The recorded configuration update time displayed in string format, i.e. yyyy/mon/dd hh:mm:ss.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiCfgFrom 1.3.6.1.4.1.171.12.1.2.8.1.1.5
The recorded IP address of the TFTP server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..100)  

swMultiCfgSendUser 1.3.6.1.4.1.171.12.1.2.8.1.1.6
The record of the user who downloaded the configuration file
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swMultiCfgFileName 1.3.6.1.4.1.171.12.1.2.8.1.1.7
When the system is set to boot from SD card, this object displays the recorded path name of the boot configuration file.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

swMultiCfgCurrentUsed 1.3.6.1.4.1.171.12.1.2.8.2
The indicated configuration file ID of the system currently in use.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swMultiCfgBootUp 1.3.6.1.4.1.171.12.1.2.8.3
This object indicates the configuration file ID which will take effect upon the next reboot.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swMultiCfgCtrlTable 1.3.6.1.4.1.171.12.1.2.8.4
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMultiCfgCtrlEntry

swMultiCfgCtrlEntry 1.3.6.1.4.1.171.12.1.2.8.4.1
A list of information about multiple configuration management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMultiCfgCtrlEntry  

swMultiCfgCtrlID 1.3.6.1.4.1.171.12.1.2.8.4.1.1
The section ID of the configuration file.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cfgId-1(1), cfgId-2(2)  

swMultiCfgAction 1.3.6.1.4.1.171.12.1.2.8.4.1.2
save: Save configuration to active configuration ID when the parameter is omitted. active: Set any valid configuration as the active configuration. delete: Removes the configuration from the flash memory. This configuration cannot be the active or current configuration file. apply: Loads the indicated configuration file and applies it to the system. config-as-bootup-cfg: Configured as the boot-up configuration by the indicated configuration(ID).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), delete(2), apply(3), none(4), config-as-bootup-cfg(5)  

systemSeverityControlMgmt 1.3.6.1.4.1.171.12.1.2.9
OBJECT IDENTIFIER    

systemSeverityTrapControl 1.3.6.1.4.1.171.12.1.2.9.1
Indicates the level of trap severity control. The system has a severity level control and each trap should have a severity control set. When trap events occur and its severity is higher than the system severity control level, the trap works as defined. If the event severity is lower than the system severity control level, the event is ignored as if it did not occur.
Status: current Access: read-write
OBJECT-TYPE    
  AgentNotifyLevel  

systemSeverityLogControl 1.3.6.1.4.1.171.12.1.2.9.2
Indicates the level of trap severity control. The system has a severity level control and each trap should have a severity control set. When trap events occur and its severity is higher than the system severity control level, the trap works as defined. If the event severity is lower than the system severity control level, the event is ignored as if it did not occur.
Status: current Access: read-write
OBJECT-TYPE    
  AgentNotifyLevel  

agentTrustedHostMgmt 1.3.6.1.4.1.171.12.1.2.10
OBJECT IDENTIFIER    

agentTrustedHostTable 1.3.6.1.4.1.171.12.1.2.10.1
This table contains the trusted host information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentTrustedHostEntry

agentTrustedHostEntry 1.3.6.1.4.1.171.12.1.2.10.1.1
A list of information about the trusted hosts.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentTrustedHostEntry  

agentTrustedHostIndex 1.3.6.1.4.1.171.12.1.2.10.1.1.1
The index of the trusted host entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

agentTrustedHostIPAddress 1.3.6.1.4.1.171.12.1.2.10.1.1.2
Specifies the IP address of the trusted host.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

agentTrustedHostRowStatus 1.3.6.1.4.1.171.12.1.2.10.1.1.3
Indicates the status of this entry. When creating a trusted host entry, the IP address should also be set.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

agentTrustedHostIPSubnetMask 1.3.6.1.4.1.171.12.1.2.10.1.1.4
Specifies the IP subnet mask of the trusted host.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

agentTrustedHostForSNMP 1.3.6.1.4.1.171.12.1.2.10.1.1.5
Specifies the trusted host for SNMP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustedHostForTELNET 1.3.6.1.4.1.171.12.1.2.10.1.1.6
Specifies the trusted host for Telnet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustedHostForSSH 1.3.6.1.4.1.171.12.1.2.10.1.1.7
Specifies the trusted host for SSH.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustedHostForHTTP 1.3.6.1.4.1.171.12.1.2.10.1.1.8
Specifies the trusted host for HTTP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustedHostForHTTPS 1.3.6.1.4.1.171.12.1.2.10.1.1.9
Specifies the trusted host for HTTPS.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustedHostForPING 1.3.6.1.4.1.171.12.1.2.10.1.1.10
Specifies the trusted host for PING.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrustedHostAddrType 1.3.6.1.4.1.171.12.1.2.10.1.1.11
The type of trusted host address as specified by the 'agentTrustedHostAddr' object.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

agentTrustedHostAddr 1.3.6.1.4.1.171.12.1.2.10.1.1.12
Specifies the IP address of the trusted host.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

agentTrustedHostIPv6PrefixLen 1.3.6.1.4.1.171.12.1.2.10.1.1.13
Specifies the IPv6 prefix length of the IPv6 trusted host.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..128  

agentTrustedHostDelAllState 1.3.6.1.4.1.171.12.1.2.10.2
Used to delete all trusted host entries.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), start(2)  

agentFDBMgmt 1.3.6.1.4.1.171.12.1.2.11
OBJECT IDENTIFIER    

agentFDBClearAllState 1.3.6.1.4.1.171.12.1.2.11.1
Used to clear all FDB entries.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentFDBClearByPortTable 1.3.6.1.4.1.171.12.1.2.11.2
Used to clear FDB entries by port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFDBClearByPortEntry

agentFDBClearByPortEntry 1.3.6.1.4.1.171.12.1.2.11.2.1
This is an entry of the agentFDBClearByPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFDBClearByPortEntry  

agentFDBClearPortIndex 1.3.6.1.4.1.171.12.1.2.11.2.1.1
This object indicates the port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

agentFDBClearByPortAction 1.3.6.1.4.1.171.12.1.2.11.2.1.2
This object indicates whether to clear FDB or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentFDBClearByVlanTable 1.3.6.1.4.1.171.12.1.2.11.3
Used to clear FDB entries by port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFDBClearByVlanEntry

agentFDBClearByVlanEntry 1.3.6.1.4.1.171.12.1.2.11.3.1
This is an entry of agentFDBClearByPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFDBClearByVlanEntry  

agentFDBClearVid 1.3.6.1.4.1.171.12.1.2.11.3.1.1
This object indicates the VLAN-ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanId  

agentFDBClearByVlanAction 1.3.6.1.4.1.171.12.1.2.11.3.1.2
This object indicates whether to clear the FDB or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentFDBSecurityTable 1.3.6.1.4.1.171.12.1.2.11.4
Used to display the FDB entries that have been created by the security module.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFDBSecurityEntry

agentFDBSecurityEntry 1.3.6.1.4.1.171.12.1.2.11.4.1
This is an entry of agentFDBSecurityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFDBSecurityEntry  

agentFDBVid 1.3.6.1.4.1.171.12.1.2.11.4.1.1
This object indicates the VLAN-ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanId  

agentFDBMacAddress 1.3.6.1.4.1.171.12.1.2.11.4.1.2
This object indicates the MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

agentFDBPort 1.3.6.1.4.1.171.12.1.2.11.4.1.3
This object indicates the port number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

agentFDBType 1.3.6.1.4.1.171.12.1.2.11.4.1.4
This object indicates the MAC address type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dynamic(1), static(2)  

agentFDBStatus 1.3.6.1.4.1.171.12.1.2.11.4.1.5
This object indicates the MAC address's forwarding status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER drop(1), forward(2)  

agentFDBSecurityModule 1.3.6.1.4.1.171.12.1.2.11.4.1.6
This object is used to indicate which security module created the current MAC address. dot1x: 802.1X. wac: Web-based Access Control. jwac: Web-Based Access Control extension for Japan. port-security: Port Security. mac-based-access-control: MAC-based Access Control. compound-authentication: Compound Authentication.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dot1x(1), wac(2), jwac(3), port-security(4), mac-based-access-control(5), compound-authentication(6)  

agentARPMgmt 1.3.6.1.4.1.171.12.1.2.12
OBJECT IDENTIFIER    

agentARPClearAllState 1.3.6.1.4.1.171.12.1.2.12.1
Used to clear all ARP entries.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentGratuitousARPMgmt 1.3.6.1.4.1.171.12.1.2.12.2
OBJECT IDENTIFIER    

agentGratuitousARPSendIpifStatusUpState 1.3.6.1.4.1.171.12.1.2.12.2.1
This is used to enable/disable sending of gratuitous ARP request packets while the IPIF interface comes up. This is used to automatically announce the interface's IP address to other nodes. By default, the state is enabled, and only one ARP packet will be broadcast.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPSendDupIpDetectedState 1.3.6.1.4.1.171.12.1.2.12.2.2
This is used to enable/disable the sending of gratuitous ARP request packets while a duplicate IP is detected. By default, the state is enabled. The duplicate IP detected state indicates that the system has received an ARP request packet that was sent by an IP address that matches the system's own IP address. In this case, the system knows that somebody out there is using an IP address that is in conflict with the system. In order to reclaim the correct host of this IP address, the system can send out the gratuitous ARP request packet for this duplicate IP address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPLearningState 1.3.6.1.4.1.171.12.1.2.12.2.3
This is used to enable/disable learning of an ARP entry in the ARP cache based on the received gratuitous ARP packet. If the switch receives a gratuitous ARP request/reply packet and the sender's IP address is in its ARP table, it should update the ARP entry. By default, the state is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPTable 1.3.6.1.4.1.171.12.1.2.12.2.4
Gratuitous ARP Table Information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentGratuitousARPEntry

agentGratuitousARPEntry 1.3.6.1.4.1.171.12.1.2.12.2.4.1
A list of information from the Gratuitous ARP Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentGratuitousARPEntry  

agentGratuitousARPInterfaceName 1.3.6.1.4.1.171.12.1.2.12.2.4.1.1
The name of the IP interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentGratuitousARPPeriodicalSendInterval 1.3.6.1.4.1.171.12.1.2.12.2.4.1.2
This is used to configure the interval for the periodic sending of gratuitous ARP request packets. 0 means do not send gratuitous ARP request packets periodically.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

agentGratuitousARPTrapState 1.3.6.1.4.1.171.12.1.2.12.2.4.1.3
This indicates the state of the gratuitous ARP trap. The switch can trap the IP conflict events to inform the administrator. By default, the trap is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentGratuitousARPLogState 1.3.6.1.4.1.171.12.1.2.12.2.4.1.4
This indicates the state of the gratuitous Log trap. The switch can log the IP conflict events to inform the administrator. By default, the event log is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentARPTotalARPEntries 1.3.6.1.4.1.171.12.1.2.12.3
Used to display the total number of ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentARPRetryTimes 1.3.6.1.4.1.171.12.1.2.12.4
This indicates the retry times of the ARP request.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

swMultiImageCtrlTable 1.3.6.1.4.1.171.12.1.2.13
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMultiImageCtrlEntry

swMultiImageCtrlEntry 1.3.6.1.4.1.171.12.1.2.13.1
A list of information about multiple image management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMultiImageCtrlEntry  

swMultiImageCtrlID 1.3.6.1.4.1.171.12.1.2.13.1.1
The stacking section ID of the firmware image. The stacking section ID = 256 * Unit ID + Image File ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swMultiImageCtrlAction 1.3.6.1.4.1.171.12.1.2.13.1.2
This object indicates the running status of the image which is specified by swMultiImageCtrlID and swMultiImageCtrlUnitID. config-as-bootup-fw (1) - Configured as the bootup firmware by the indicated firmware(ID). delete (2) - Delete the firmware by indicated firmware ID. none (3) - No action.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER config-as-bootup-fw(1), delete(2), none(3)  

agentOutOfBandDataBits 1.3.6.1.4.1.171.12.1.2.14
This object indicates the out-of-band data bits.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentOutOfBandParityBits 1.3.6.1.4.1.171.12.1.2.15
This object indicates the out-of-band parity bits.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentOutOfBandStopBits 1.3.6.1.4.1.171.12.1.2.16
This object indicates the out-of-band stop bits.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

agentOutOfBandAutoLogoutConfig 1.3.6.1.4.1.171.12.1.2.17
This object allows the user to specify an out-of-band auto logout time.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER never(1), minutes-2(2), minutes-5(3), minutes-10(4), minutes-15(5)  

agentBscFileSystemMgmt 1.3.6.1.4.1.171.12.1.2.18
OBJECT IDENTIFIER    

agentBscFileSystemTable 1.3.6.1.4.1.171.12.1.2.18.1
A list of MIB File System Basic Configuration entries supported by the file update of this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentBscFileSystemEntry

agentBscFileSystemEntry 1.3.6.1.4.1.171.12.1.2.18.1.1
A File System basic configuration entry that contains objects describing a particular MIB supported by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentBscFileSystemEntry  

agentBscFileSystemIndex 1.3.6.1.4.1.171.12.1.2.18.1.1.1
The table index for the file entry. This object describes the file type. runtime-code (1), log-file (2), cfg-file (3), attack-log-file (7)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentBscFileSystemDscr 1.3.6.1.4.1.171.12.1.2.18.1.1.2
The description of the software file purpose in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscFileSystemServerAddr 1.3.6.1.4.1.171.12.1.2.18.1.1.3
The IP address where the file to be downloaded is located, or the IP address where the file will be uploaded to.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentBscFileSystemServerIPv6Addr 1.3.6.1.4.1.171.12.1.2.18.1.1.4
The IPv6 address where the file is to be downloaded from or uploaded to.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

agentBscFileSystemServerFileName 1.3.6.1.4.1.171.12.1.2.18.1.1.5
The name of the file to be downloaded from or uploaded to the TFTP server. If agentBscFileSystemDeviceFileName is not set, the switch will default to using the bootup file as the runtime image for the switch.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscFileSystemDeviceDriverID 1.3.6.1.4.1.171.12.1.2.18.1.1.6
Specifies the drive of the device that the firmware to be uploaded/downloaded is located. If none (1) is specified, the switch will default to the current drive.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), a(2), b(3), c(4), d(5), e(6), f(7), g(8), h(9), i(10), j(11), k(12), l(13), m(14), n(15), o(16), p(17), q(18), r(19), s(20), t(21), u(22), v(23), w(24), x(25), y(26), z(27)  

agentBscFileSystemDeviceFileName 1.3.6.1.4.1.171.12.1.2.18.1.1.7
The name of the file to be downloaded to the device, or uploaded from the device. When downloading or uploading, the agentBscFileSystemServerFileName object must also be set.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscFileSystemLoadType 1.3.6.1.4.1.171.12.1.2.18.1.1.8
This object allows the user to select a download or upload function for the file. Note: For systems that do not support changes to this object, setting a value for this object will cause the system to return a bad-value error message.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

agentBscFileSystemCtrlUnitID 1.3.6.1.4.1.171.12.1.2.18.1.1.9
Specifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bit from left to right represents the switch from unit ID 1 to unit ID 12. If this list is set to null it represents all stack switches.
Status: current Access: read-write
OBJECT-TYPE    
  UnitList  

agentBscFileSystemBootUpImage 1.3.6.1.4.1.171.12.1.2.18.1.1.10
The result of the download will depend on whether the boot_up option has been specified. Case 1: In the case of the master unit providing the file system and the slave unit not providing the file system, when the boot_up parameter is specified, then the file will be downloaded to the boot_up image on the slave. If the boot_up parameter is not specified, then the file will not be downloaded to this slave unit. Case 2: In the case of the master unit not providing the file system and the slave unit providing the file system, when the boot_up parameter is specified, then the file will be downloaded to the boot_up image on the slave unit. If boot_up is not specified, then the file will not be downloaded to this slave unit. Case 3: In the case of the master unit and the slave unit both supporting or not supporting the file system, the file will be downloaded to the specified file on the slave unit. If boot_up is specified, the downloaded file will be assigned as the boot_up image. True: boot_up option is specified. False: boot_up option is not specified..
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentBscFileSystemForceAgree 1.3.6.1.4.1.171.12.1.2.18.1.1.11
When the force_agree option is specified, the reboot command will be executed immediately without any further confirmation from the user. True: force_agree option is specified. False: force_agree option is not specified..
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentBscFileSystemCtrl 1.3.6.1.4.1.171.12.1.2.18.1.1.12
This object allows the user to download runtime software. The settings will take effect when the system restarts. See Note (1) below Note 1: For systems which do not support value changes to this object, setting these values will cause the system to return a bad-value error message start (3) - activate firmware.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), inactive(2), start(3)  

agentBscFileSystemInterfaceName 1.3.6.1.4.1.171.12.1.2.18.1.1.13
This node is used to specify the interface name when agentBscFileSystemServerIPv6Addr is the local link address.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

agentBscFileSystemServerDomainName 1.3.6.1.4.1.171.12.1.2.18.1.1.14
This object indicates the domain name of the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

agentBscFileSystemIncrement 1.3.6.1.4.1.171.12.1.2.18.1.1.15
If increment is specified, then the existing configuration will not be cleared before applying of the new configuration. If it is not specified, then the existing configuration will be cleared before applying of the new configuration. True : keep valid False : erase.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentBscFileSystemSaveConfigDriverID 1.3.6.1.4.1.171.12.1.2.18.2
The drive on the device that the configuration file is will be saved to. If none (1) is specified, the switch places the file on the current drive by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), a(2), b(3), c(4), d(5), e(6), f(7), g(8), h(9), i(10), j(11), k(12), l(13), m(14), n(15), o(16), p(17), q(18), r(19), s(20), t(21), u(22), v(23), w(24), x(25), y(26), z(27)  

agentBscFileSystemSaveConfigFileName 1.3.6.1.4.1.171.12.1.2.18.3
The name of the configuration file that will be saved to the device. When agentBscFileSystemSaveCfg is set to cfg (2), and if the agentBscFileSystemSaveConfigFileName is not null, the configuration file will be saved to the set file name. If set to null, the configuration file will be saved to the boot_up CFG file.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscFileSystemSaveCfg 1.3.6.1.4.1.171.12.1.2.18.4
This indicates the method of saving information to the NV-RAM of the device. other (1) - None of the following. cfg (2) - Save configuration. log (3) - Save log. all (4) - Save both ( active configuration and log).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), cfg(2), log(3), all(4)  

agentFileSystemConfigTable 1.3.6.1.4.1.171.12.1.2.18.5
This table indicates the information about the bootup files.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFileSystemConfigEntry

agentFileSystemConfigEntry 1.3.6.1.4.1.171.12.1.2.18.5.1
A list of information about the bootup files for each unit of the switch stack.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFileSystemConfigEntry  

agentFileSystemUnit 1.3.6.1.4.1.171.12.1.2.18.5.1.1
The unit ID.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentFileSystemDriverID 1.3.6.1.4.1.171.12.1.2.18.5.1.2
The drive on the device that the configuration file will be saved to. If none (1) is specified, the switch will place the file to the current drive by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), a(2), b(3), c(4), d(5), e(6), f(7), g(8), h(9), i(10), j(11), k(12), l(13), m(14), n(15), o(16), p(17), q(18), r(19), s(20), t(21), u(22), v(23), w(24), x(25), y(26), z(27)  

agentFileSystemBootImage 1.3.6.1.4.1.171.12.1.2.18.5.1.3
When displayed, it shows the current bootup image file name. When set, the set name will be set as the bootup image.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentFileSystemBootConfig 1.3.6.1.4.1.171.12.1.2.18.5.1.4
When displayed, it shows the current bootup configuration file name. When set, the set name will be set as the bootup configuration.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentFileSystemActConfig 1.3.6.1.4.1.171.12.1.2.18.5.1.5
When displayed, it shows null. When set, the set name will be active at once, but the set name will not be set as the bootup configuration.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentReboot 1.3.6.1.4.1.171.12.1.2.19
Used to restart the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), start(2)  

agentReset 1.3.6.1.4.1.171.12.1.2.20
Used to reset all switch parameters. none (1): No action. This is the default value of this object. config (2): All parameters are reset to default settings. The device will neither save nor reboot. system (3): All parameters are reset to default settings. The switch will then do a factory reset, save, and reboot. reset (4) : All parameters will be reset to default settings except for the IP address, user account, and history log. The device will neither save nor reboot. system-exclude-vlan(5) : All parameters are reset to default settings except for VLAN. The switch will then save its settings and reboot. system-exclude-ip(6) : All parameters are reset to default settings except IP address. The switch will then save its settings and reboot. system-exclude-vlan-ip(7): All parameters are reset to default settings except VLAN and IP address. The switch will then save its settings and reboot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), config(2), system(3), reset(4), system-exclude-vlan(5), system-exclude-ip(6), system-exclude-vlan-ip(7)  

agentFTPFileTable 1.3.6.1.4.1.171.12.1.2.21
A list of the MIB Basic Config entries support files updated by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFTPFileEntry

agentFTPFileEntry 1.3.6.1.4.1.171.12.1.2.21.1
A basic configuration entry containing the objects describing a particular MIB supported by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFTPFileEntry  

agentFTPFileIndex 1.3.6.1.4.1.171.12.1.2.21.1.1
The table index for the file entry. This object describes the file type runtime-code (1), log-file (2), cfg-file (3)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentFTPFileDscr 1.3.6.1.4.1.171.12.1.2.21.1.2
The description of the software file purpose in this entry. Note: For systems which do not support changes to this object, setting a value for this object will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentFTPFileLoadType 1.3.6.1.4.1.171.12.1.2.21.1.3
This object provides the user with a choice of uploading or downloading the selected file. Note: For systems which do not support a change of this object, setting a value to this object will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

agentFTPFileAddr 1.3.6.1.4.1.171.12.1.2.21.1.4
The IP address that the file to be downloaded is located on, or the IP address where the file will be uploaded to.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentFTPTCPPort 1.3.6.1.4.1.171.12.1.2.21.1.5
The TCP port number being used to establish the command connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

agentFTPFileName 1.3.6.1.4.1.171.12.1.2.21.1.6
The name of the file to be downloaded from, or uploaded to, the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

agentFTPUserName 1.3.6.1.4.1.171.12.1.2.21.1.7
This is the user name to enter in upload/download.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

agentFTPPassword 1.3.6.1.4.1.171.12.1.2.21.1.8
This is the password to enter for an upload/download.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

agentFTPFileCtrlID 1.3.6.1.4.1.171.12.1.2.21.1.9
The section ID of the firmware image or configuration file. A value of 0 indicates the boot-up firmware image or configuration file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

agentFTPFileBIncrement 1.3.6.1.4.1.171.12.1.2.21.1.10
This object indicates whether the previous configuration will remain valid or not after downloading the configuration file. True: Keep valid False: Erase.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentFTPFileCtrl 1.3.6.1.4.1.171.12.1.2.21.1.11
This object gives the user the option to download runtime software. The setting will take effect when the system restarts. See Note (1) below Note 1: For systems which do not support changes to this object, setting a value for this object will cause the system to return bad-value error messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentFTPFileBootUpImage 1.3.6.1.4.1.171.12.1.2.21.1.12
This object indicates whether to set the special file as a boot up file or not. True: The boot-up option is specified. False: The boot-up option is not specified.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentFTPFileForceAgree 1.3.6.1.4.1.171.12.1.2.21.1.13
When the force-agree option is specified, the reboot command will be executed immediately without any further confirmation from the user. True: Force-agree option is specified. False: Force-agree option is not specified.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentFTPFileIPv6Addr 1.3.6.1.4.1.171.12.1.2.21.1.14
The IPv6 address where the file is to be downloaded from or uploaded to.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

agentFTPFileInterfaceName 1.3.6.1.4.1.171.12.1.2.21.1.15
This node is used to specify the interface name when agentFTPFileIPv6Addr is the local link address.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

agentFTPFileUnitID 1.3.6.1.4.1.171.12.1.2.21.1.16
Specifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bit from left to right represents the switch from unit ID 1 to unit ID 12.If this list is set to null it represents all stack switches.
Status: current Access: read-write
OBJECT-TYPE    
  UnitList  

agentSnmpTrapState 1.3.6.1.4.1.171.12.1.2.22
This object indicates if the SNMP trap is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentOutOfBandMgmt 1.3.6.1.4.1.171.12.1.2.23
OBJECT IDENTIFIER    

agentOutOfBandMgmtState 1.3.6.1.4.1.171.12.1.2.23.1
Enables or disables the interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentOutOfBandMgmtIpAddr 1.3.6.1.4.1.171.12.1.2.23.2
The IP address for out of band management. This object can only take the value of the unicast IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentOutOfBandMgmtSubnetMask 1.3.6.1.4.1.171.12.1.2.23.3
The IP net mask for out of band management.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentOutOfBandMgmtGateway 1.3.6.1.4.1.171.12.1.2.23.4
The gateway for out of band management.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentOutOfBandMgmtLinkStatus 1.3.6.1.4.1.171.12.1.2.23.5
The current Link status for out of band management.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER link-up(1), link-down(2)  

agentTrapMgmt 1.3.6.1.4.1.171.12.1.2.24
OBJECT IDENTIFIER    

agentTrapColdStart 1.3.6.1.4.1.171.12.1.2.24.1
When enabled (1), whenever the device detects a cold start event, a trap will be sent out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrapWarmStart 1.3.6.1.4.1.171.12.1.2.24.2
When enabled (1), whenever the device detects a warm start event, a trap will be sent out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrapRmonRisingAlarm 1.3.6.1.4.1.171.12.1.2.24.3
When enabled (1), whenever the device detects a RMON rising alarm event , a trap will be sent out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrapRmonFallingAlarm 1.3.6.1.4.1.171.12.1.2.24.4
When enabled (1), whenever the device detects a RMON falling alarm event, a trap will be sent out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrapCfgSave 1.3.6.1.4.1.171.12.1.2.24.5
When enabled (1), whenever the device detects a configuration saving completed event, a trap will be sent out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrapCfgUpload 1.3.6.1.4.1.171.12.1.2.24.6
When enabled (1), whenever the device detects a configuration uploading completed event, a trap will be sent out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentTrapCfgDownload 1.3.6.1.4.1.171.12.1.2.24.7
When enabled (1), whenever the device detects a configuration downloading completed event, a trap will be sent out
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentFTPFileSystemTable 1.3.6.1.4.1.171.12.1.2.25
The FTP management table for the file system
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentFTPFileSystemEntry

agentFTPFileSystemEntry 1.3.6.1.4.1.171.12.1.2.25.1
A File System basic configuration entry that contains objects describing a particular MIB supported by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentFTPFileSystemEntry  

agentFTPFileSystemIndex 1.3.6.1.4.1.171.12.1.2.25.1.1
The table index for the file entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

agentFTPFileSystemDscr 1.3.6.1.4.1.171.12.1.2.25.1.2
The description of the software file purpose in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

agentFTPFileSystemLoadType 1.3.6.1.4.1.171.12.1.2.25.1.3
This object allows the user to select a download or upload function for the file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

agentFTPFileSystemAddressType 1.3.6.1.4.1.171.12.1.2.25.1.4
The address type of agentFTPFileSystemAddress.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

agentFTPFileSystemAddress 1.3.6.1.4.1.171.12.1.2.25.1.5
This object indicates the FTP server address.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

agentFTPFileSystemTCPPort 1.3.6.1.4.1.171.12.1.2.25.1.6
The TCP port number being used to establish the control connection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

agentFTPFileSystemServerFileName 1.3.6.1.4.1.171.12.1.2.25.1.7
The name of the file to be downloaded from or uploaded to the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentFTPFileSystemDeviceFileName 1.3.6.1.4.1.171.12.1.2.25.1.8
The name of the file to be downloaded to the device, or uploaded from the device. If agentFTPFileSystemDeviceFileName is not set, the switch will default to the bootup file.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentFTPFileSystemUserName 1.3.6.1.4.1.171.12.1.2.25.1.9
This object indicates the user name to access the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

agentFTPFileSystemPassword 1.3.6.1.4.1.171.12.1.2.25.1.10
This object indicates the password to access the FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

agentFTPFileSystemCtrlUnitID 1.3.6.1.4.1.171.12.1.2.25.1.11
Specifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bit from left to right represents the switch from unit ID 1 to unit ID 12.If this list is set to null it represents all stack switches.
Status: current Access: read-write
OBJECT-TYPE    
  UnitList  

agentFTPFileSystemBootUpImage 1.3.6.1.4.1.171.12.1.2.25.1.12
This object indicates whether to set the special file as the boot up file or not. True: The boot-up option is specified. False: The boot-up option is not specified.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

agentFTPFileSystemCtrl 1.3.6.1.4.1.171.12.1.2.25.1.13
This object allows the user to execute an FTP download/upload.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), start(2)  

agentBscCMDLogState 1.3.6.1.4.1.171.12.1.2.26
This object indicates the command logging state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentBscBroadcastPingReplyState 1.3.6.1.4.1.171.12.1.2.27
This object indicates the broadcast ping reply state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentBscTftpConfigMgmt 1.3.6.1.4.1.171.12.1.2.28
OBJECT IDENTIFIER    

agentBscTftpCfgFirmwareFile 1.3.6.1.4.1.171.12.1.2.28.1
The firmware pathname that needs to be downloaded/uploaded from/to the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgConfigFile 1.3.6.1.4.1.171.12.1.2.28.2
The configuration pathname that needs to be downloaded/uploaded from/to the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgLogFile 1.3.6.1.4.1.171.12.1.2.28.3
The log pathname that needs to be uploaded to the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgAttackLogFile 1.3.6.1.4.1.171.12.1.2.28.4
The attack log pathname that needs to be uploaded to the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgCertificateFile 1.3.6.1.4.1.171.12.1.2.28.5
The certificate pathname that needs to be downloaded from the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgKeyFile 1.3.6.1.4.1.171.12.1.2.28.6
The key pathname that needs to be downloaded from the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgTechSuooprtFile 1.3.6.1.4.1.171.12.1.2.28.7
The technique's support information pathname that needs to be uploaded to the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgDebugLogFile 1.3.6.1.4.1.171.12.1.2.28.8
The debug log pathname that needs to be uploaded to the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgSIMFirmwareFile 1.3.6.1.4.1.171.12.1.2.28.9
The firmware pathname that needs to be downloaded/uploaded from/to the TFTP server when it is SIM enabled.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgSIMConfigFile 1.3.6.1.4.1.171.12.1.2.28.10
The configuration pathname that needs to be downloaded/uploaded from/to the TFTP server when it is SIM enabled.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgSIMLogFile 1.3.6.1.4.1.171.12.1.2.28.11
The log pathname that needs to be uploaded to the TFTP server when it is SIM enabled.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentBscTftpCfgServerIPAddr 1.3.6.1.4.1.171.12.1.2.28.12
The IPv4 address of the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentBscTftpCfgServerIPv6Addr 1.3.6.1.4.1.171.12.1.2.28.13
The IPv6 address of the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

agentBscTftpCfgServerDomainName 1.3.6.1.4.1.171.12.1.2.28.14
The domain name of the TFTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

agentBscCommunityEncryptionState 1.3.6.1.4.1.171.12.1.2.29
This object indicates the encryption state on the SNMP community string.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentIpProtoConfig 1.3.6.1.4.1.171.12.1.3
OBJECT IDENTIFIER    

agentIpNumOfIf 1.3.6.1.4.1.171.12.1.3.1
The total number of IP interfaces supported by this agent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

agentIpTftpServerAddr 1.3.6.1.4.1.171.12.1.3.2
The IP address of the TFTP Server.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

agentIpGetIpFrom 1.3.6.1.4.1.171.12.1.3.3
This object indicates if the agent will get its system IP address from a Bootp/DHCP server at start up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), bootp(3), dhcp(4)  

agentIpAutoconfig 1.3.6.1.4.1.171.12.1.3.4
Indicates the status of automatically getting the configuration information from a TFTP server connected to the device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agentIpAutoconfigTimeout 1.3.6.1.4.1.171.12.1.3.5
This timer is used to limit the length of time for getting the configuration information from a TFTP server connected to the device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

agentIpTrapManager 1.3.6.1.4.1.171.12.1.4
OBJECT IDENTIFIER    

agentTrapManagerTable 1.3.6.1.4.1.171.12.1.4.2
A list of trap managers that the SNMP traps will be sent to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentTrapManagerEntry

agentTrapManagerEntry 1.3.6.1.4.1.171.12.1.4.2.1
Each entry contains the particular trap manager's settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentTrapManagerEntry  

agentTrapManagerIndex 1.3.6.1.4.1.171.12.1.4.2.1.1
A value that uniquely identifies trapDestEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..65535  

agentTrapManagerIpAddr 1.3.6.1.4.1.171.12.1.4.2.1.2
The destination IP address for SNMP traps.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

agentTrapManagerComm 1.3.6.1.4.1.171.12.1.4.2.1.3
The community string used to encode SNMP trap packets being sent to the trap manager.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

agentTrapManagerMsgVer 1.3.6.1.4.1.171.12.1.4.2.1.4
This object indicates the version of trap packets that will be sent to this trap manager. The default setting is SNMP Agent Version Dependent. Note: Because some of these functions will be limited by the support of the system in question, some selected items may be invalid. If one of these items is selected, a bad value error message will prompt the user.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER snmpAgentVersionDependent(1), v1Trap(2), v2Trap(3)  

agentTrapManagerStatus 1.3.6.1.4.1.171.12.1.4.2.1.5
This object indicates whether or not the trap should be sent to the trap manager.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

agentNotify 1.3.6.1.4.1.171.12.1.7
OBJECT IDENTIFIER    

agentNotifMgmt 1.3.6.1.4.1.171.12.1.7.1
OBJECT IDENTIFIER    

agentNotifFirmware 1.3.6.1.4.1.171.12.1.7.2
OBJECT IDENTIFIER    

agentNotifyPrefix 1.3.6.1.4.1.171.12.1.7.2.0
OBJECT IDENTIFIER    

notifFirmwareMgmt 1.3.6.1.4.1.171.12.1.7.1.2
OBJECT IDENTIFIER    

agentsystemRestart 1.3.6.1.4.1.171.12.1.7.2.0.1
This trap contains the reboot information.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentSaveToNVRAM 1.3.6.1.4.1.171.12.1.7.2.0.2
This trap is sent whenever all the device configuration has been saved to NV-RAM.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentFileTransferStatusChange 1.3.6.1.4.1.171.12.1.7.2.0.3
File transfer status change notification.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentSetToFactoryDefault 1.3.6.1.4.1.171.12.1.7.2.0.4
This trap is sent whenever the 'set to factory default' setting has been processed.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentGratuitousARPTrap 1.3.6.1.4.1.171.12.1.7.2.0.5
This trap is sent when there is an IP address conflict.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentLoginFailTrap 1.3.6.1.4.1.171.12.1.7.2.0.6
The trap is sent when a login has failed through one of the login types (console, Telnet, web, SSL or SSH).
Status: current Access: read-write
NOTIFICATION-TYPE    

agentFirmwareUpgrade 1.3.6.1.4.1.171.12.1.7.2.0.7
This trap is sent when the process of upgrading the firmware via SNMP has finished.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentAccessFlashFailed 1.3.6.1.4.1.171.12.1.7.2.0.8
The trap is sent when access to the flash fails.
Status: current Access: read-write
NOTIFICATION-TYPE    

agentCfgOperCompleteTrap 1.3.6.1.4.1.171.12.1.7.2.0.9
The trap is sent when the configuration is completely saved, uploaded or downloaded.
Status: current Access: read-write
NOTIFICATION-TYPE    

notificationBindings 1.3.6.1.4.1.171.12.1.7.2.1
OBJECT IDENTIFIER    

unitID 1.3.6.1.4.1.171.12.1.7.2.1.1
The unit ID of the device which triggered the event.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

trapInfosystemRestart 1.3.6.1.4.1.171.12.1.7.2.1.2
This object indicates the last time the device rebooted.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentGratuitousARPIpAddr 1.3.6.1.4.1.171.12.1.7.2.1.3
A duplicate IP address with the switch already exists.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

agentGratuitousARPMacAddr 1.3.6.1.4.1.171.12.1.7.2.1.4
This object is the MAC address of the device which has the duplicate IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

agentGratuitousARPPortNumber 1.3.6.1.4.1.171.12.1.7.2.1.5
This indicates the portNum with a string. For example, if the device is in standalone mode, and the port number is 23, the string should be 23. If the device is in stacking mode, and the unit ID is 2, and the port number is 3, the string should be 2:3.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

agentLoginType 1.3.6.1.4.1.171.12.1.7.2.1.6
The type is the user login method type.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER console(1), telnet(2), web(3), ssl(4), ssh(5)  

agentLoginAAAMethod 1.3.6.1.4.1.171.12.1.7.2.1.7
This method is the AAA login method.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER none(1), local(2), server(3)  

agentLoginUserName 1.3.6.1.4.1.171.12.1.7.2.1.8
This object is the name of the user that failed to login to the switch.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

agentLoginIpAddr 1.3.6.1.4.1.171.12.1.7.2.1.9
This object is the login type from the IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

agentLoginMacAddr 1.3.6.1.4.1.171.12.1.7.2.1.10
This object is the login type from a MAC address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MacAddress  

agentLoginAAAServerAddr 1.3.6.1.4.1.171.12.1.7.2.1.11
This object is the login type through a console authenticated by an AAA server.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

agentLoginFailInfo 1.3.6.1.4.1.171.12.1.7.2.1.12
This object indicates the reason for the login failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER other(1), authenticate-fail(2), server-timeout(3)  

agentAccessFlashOper 1.3.6.1.4.1.171.12.1.7.2.1.13
This object indicates the operation of the access flash failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString Size(0..64)  

agentAccessFlashAddr 1.3.6.1.4.1.171.12.1.7.2.1.14
This object indicates the address of the access flash failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER  

agentCfgOperate 1.3.6.1.4.1.171.12.1.7.2.1.15
This object indicates the operation type of the configuration.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER save(1), upload(2), download(3)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor