ADTRAN-DSUDPP-MIB
File:
ADTRAN-DSUDPP-MIB.mib (39740 bytes)
Imported modules
Imported symbols
Defined Types
| AdDSUDPds0IntervalEntry |
|
| SEQUENCE |
|
|
|
| |
adDSUDPds0IntervalIndex |
INTEGER |
|
| |
adDSUDPds0IntervalNumber |
INTEGER |
|
| |
adDSUDPds0IntervalUASs |
Counter |
|
| AdDSUDPds0DailyEntry |
|
| SEQUENCE |
|
|
|
| |
adDSUDPds0DailyIndex |
INTEGER |
|
| |
adDSUDPds0DailyNumber |
INTEGER |
|
| |
adDSUDPds0DailyUASs |
Counter |
|
| |
adDSUDPds0DailyAvail |
INTEGER |
|
| |
adDSUDPds0DailyAvgAvail |
INTEGER |
|
| AdDSUDPds0IntervalThrsEntry |
|
| SEQUENCE |
|
|
|
| |
adDSUDPds0IntervalThrsIndex |
INTEGER |
|
| |
adDSUDPds0IntervalThrsUASs |
INTEGER |
|
| AdDSUDPds0DailyThrsEntry |
|
| SEQUENCE |
|
|
|
| |
adDSUDPds0DailyThrsIndex |
INTEGER |
|
| |
adDSUDPds0DailyThrsUASs |
INTEGER |
|
| |
adDSUDPds0DailyThrsAvail |
INTEGER |
|
| AdDSUDPds0AlertEntry |
|
| SEQUENCE |
|
|
|
| |
adDSUDPds0AlertIndex |
INTEGER |
|
| |
adDSUDPds0AlertStatus |
INTEGER |
|
| |
adDSUDPds0AlertEnable |
INTEGER |
|
Defined Values
| adtran |
1.3.6.1.4.1.664 |
| OBJECT IDENTIFIER |
|
|
|
| adDSUDP |
1.3.6.1.4.1.664.1.8 |
| OBJECT IDENTIFIER |
|
|
|
| adMgmt |
1.3.6.1.4.1.664.2 |
| OBJECT IDENTIFIER |
|
|
|
| adDSUDPmg |
1.3.6.1.4.1.664.2.8 |
| OBJECT IDENTIFIER |
|
|
|
| adDSUDPnetLoopRate |
1.3.6.1.4.1.664.2.8.3.1.1 |
| Indicates the DS0 loop data rate |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
bps2400(1), bps4800(2), bps9600(3), bps19k(4), bps38k(5), bps56k(6), bps64k(7) |
|
| adDSUDPnetType |
1.3.6.1.4.1.664.2.8.3.1.2 |
| Selects the network type |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
dds(1), accunetSW56(2), usSprintSW56(3) |
|
| adDSUDPnetScrambler |
1.3.6.1.4.1.664.2.8.3.1.3 |
| Disables/Enables Scrambling |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
normalData(1), scrambledData(2), suppressLBE(3) |
|
| adDSUDPnetRemoteCfg |
1.3.6.1.4.1.664.2.8.3.1.4 |
| Enables/Disables configuration by a remote DSUDP |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enable(1), disable(2) |
|
| adDSUDPdteRate |
1.3.6.1.4.1.664.2.8.3.2.1 |
| Selects bit rate of primary DTE |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
bps2400(1), bps4800(2), bps9600(3), bps19k(4), bps38k(5), bps56kor57p6k(6), bps64k(7) |
|
| adDSUDPdteWordLength |
1.3.6.1.4.1.664.2.8.3.2.3 |
| Selects DTE asynchronous word length |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
bits9(1), bits10(2), bits11(3) |
|
| adDSUDPdteInBandCommand |
1.3.6.1.4.1.664.2.8.3.2.4 |
| Selects DTE in-band command type |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enableAT(2), enableV25SDLC(3), enableV25BCCASY(4) |
|
| adDSUDPdteTxClock |
1.3.6.1.4.1.664.2.8.3.2.5 |
| Selects transmit timing source |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
internal(1), external(2) |
|
| adDSUDPdteCSOptions |
1.3.6.1.4.1.664.2.8.3.2.6 |
| Configures CS signal lead on primary DTE |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
forceOn(1), followsRS(2), onWithCD(3), onWithRSandCD(4), off5secAfterLOCD(5) |
|
| adDSUDPdteAntiStream |
1.3.6.1.4.1.664.2.8.3.2.7 |
| Configures DTE Anti-Streaming Disconnect |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), active10Sec(2), active30Sec(3), active60Sec(4) |
|
| adDSUDPdteCDOptions |
1.3.6.1.4.1.664.2.8.3.2.8 |
| Configures CD signal lead on primary DTE |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
forceOn(1), normal(2), off5SecAfterLOCD(3) |
|
| adDSUDPdteTROptions |
1.3.6.1.4.1.664.2.8.3.2.9 |
| Configures handling of TR lead from Primary DTE |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ignore(1), normal(2), offOnDials0(3), offOnDials1(4) |
|
| adDSUDPdteSROptions |
1.3.6.1.4.1.664.2.8.3.2.10 |
| Configures SR signal lead to primary DTE |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
forceOn(1), offWithOOS(2), offWithLOCD(3), offInTest(4), offInTestAndOOS(5), offInTestAndLOCD(6) |
|
| adDSUDPdteRSCSDelay |
1.3.6.1.4.1.664.2.8.3.2.11 |
| Configures DTE signals RS-CS delay |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
shortDelay(1), longDelay(2) |
|
| adDSUDPtestTimeout |
1.3.6.1.4.1.664.2.8.3.3.1 |
| Configures test timeout in seconds |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPtestRdlCfg |
1.3.6.1.4.1.664.2.8.3.3.2 |
| Enables/Disables response to Remote Digital Loopback |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enable(1), disable(2) |
|
| adDSUDPAutoAnswer |
1.3.6.1.4.1.664.2.8.3.4.11 |
| Enables/Disables automatic answer of incoming calls |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enable(1), disable(2) |
|
| adDSUDPTestCmd |
1.3.6.1.4.1.664.2.8.6.1 |
| A SET performs the selected test |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noTest(1), doLocalDigital(2), doRemoteLoopback(3), doRemoteLoopbackPtrn(4), doTestPatternOnly(5), doDTEAndLoop(6), doRTTest(7), doDTEOnly(8), doDTEAndPtrn(9), doSelfTest(10) |
|
| adDSUDPTestStatus |
1.3.6.1.4.1.664.2.8.6.2 |
| Current test status |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noTest(1), localAnalogLoop(2), localLoopRT(3), loopAndDTE(4), remoteConfigMaster(5), remoteConfigSlave(6), remoteLoop(7), remoteLoopPtrn(8), localAnalogLoopPtrn(9), testPattern(10), localLoopFromCO(11), remoteTestFromCO(12), remoteDigitalLoop(13) |
|
| adDSUDPTestErrors |
1.3.6.1.4.1.664.2.8.6.3 |
| This variable accumulates errors for the active test
pattern. A SET operation will clear the error count. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPTestRxPattern |
1.3.6.1.4.1.664.2.8.6.4 |
| Receive test pattern status |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noTest(1), noSync(2), patternSync(3) |
|
| adDSUDPSelfDiagnostics |
1.3.6.1.4.1.664.2.8.6.5 |
| Current Self Test status |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inTest(1), selfTestPass(2), failedEEPROM(3), failedSRAM(4), failedChecksum(5), failedBERT(6) |
|
| adDSUDPTestTxPattern |
1.3.6.1.4.1.664.2.8.6.6 |
| SETs default transmit test pattern |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ptrn2047(1), ptrn511(2), ptrnStress1(3), ptrnStress2(4), ptrnStress3(5), ptrnStress4(6) |
|
| adDSUDPInjectError |
1.3.6.1.4.1.664.2.8.6.7 |
| SET injects one error into active test pattern |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPStatusEIA |
1.3.6.1.4.1.664.2.8.7.1 |
| Bit map status of Primay DTE EIA interface signals
(off = 0, on = 1), where bit positions are:
1 RI
2 RD
4 SD
8 CD
16 CS
32 RS
64 SR
128 TR |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPStatusConnector |
1.3.6.1.4.1.664.2.8.7.2 |
| The jumper selected DTE interface connector on DSUDP |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
connectorV35(1), connectorEIA232(2) |
|
| adDSUDPMode |
1.3.6.1.4.1.664.2.8.7.3 |
| Current mode of DSUDP |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
idle(1), incomingCall(2), dialing(3), data(4), command(5) |
|
| adDSUDPLedStatus |
1.3.6.1.4.1.664.2.8.7.4 |
| This variable contains bit encoded values
for LED status (0=off, 1=on):
1 IDL
2 ALM
4 TST
8 ERR |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPDialStored |
1.3.6.1.4.1.664.2.8.8.1 |
| Dials the stored number in register 1-10 |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..10 |
|
| adDSUDPAnswerCall |
1.3.6.1.4.1.664.2.8.8.3 |
| A SET answers an incoming call |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPHangUp |
1.3.6.1.4.1.664.2.8.8.4 |
| A SET commands the DSUDP to go on-hook |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0IntervalEntry |
1.3.6.1.4.1.664.2.8.4.2.1 |
| An entry in the DS0 Interval Table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
AdDSUDPds0IntervalEntry |
|
|
| adDSUDPds0IntervalIndex |
1.3.6.1.4.1.664.2.8.4.2.1.1 |
| The index value which uniquely identifies the
DS0 interface to which this entry is applicable. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0IntervalNumber |
1.3.6.1.4.1.664.2.8.4.2.1.2 |
| A number between 1 and 97, where 1 is the current
accumulating 15 minute interval and 2-97 are
completed 15 minute intervals. 2 is the most recent
completed interval and 97 is the least recent completed
15 minute interval (assuming that all 97 intervals are
valid). |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..97 |
|
| adDSUDPds0IntervalUASs |
1.3.6.1.4.1.664.2.8.4.2.1.3 |
| The number of Unavailable Seconds encountered by a
DS0 interface in one of the 97, individual 15 minute,
intervals. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| adDSUDPds0DailyEntry |
1.3.6.1.4.1.664.2.8.4.3.1 |
| An entry in the DS0 Daily table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
AdDSUDPds0DailyEntry |
|
|
| adDSUDPds0DailyIndex |
1.3.6.1.4.1.664.2.8.4.3.1.1 |
| The index value which uniquely identifies the
DS0 interface to which this entry is applicable. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0DailyNumber |
1.3.6.1.4.1.664.2.8.4.3.1.2 |
| A number between 1 and 7, where 1 is the current
accumulating Daily Interval and 2-7 are the completed
Daily Intervals. 2 is the most recent completed Daily
Interval and 7 is the least recent completed Daily
Interval (assuming that all 7 Daily Intervals are
valid). |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0DailyUASs |
1.3.6.1.4.1.664.2.8.4.3.1.3 |
| The number of Unavailable Seconds encountered by
a DS0 interface in one of the 7 Daily Intervals. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| adDSUDPds0DailyAvail |
1.3.6.1.4.1.664.2.8.4.3.1.4 |
| The percentage (times 100) of channel availability
encountered by a DS0 interface in one of the 7 Daily
Intervals. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0DailyAvgAvail |
1.3.6.1.4.1.664.2.8.4.3.1.5 |
| The percentage (times 100) of channel availability
averaged over the last 7 days |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0IntervalThrsEntry |
1.3.6.1.4.1.664.2.8.4.4.1 |
| An entry in the DS0 Threshold Table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
AdDSUDPds0IntervalThrsEntry |
|
|
| adDSUDPds0IntervalThrsIndex |
1.3.6.1.4.1.664.2.8.4.4.1.1 |
| The index value which uniquely identifies the
DS0 interface to which this entry is applicable. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0IntervalThrsUASs |
1.3.6.1.4.1.664.2.8.4.4.1.2 |
| The DS0 performance monitor Threshold Value for the
15 minute Unavailable Seconds parameter. The default
value is 1, which equates to approximately 99.9%
Availability for a 15 minute Interval. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0DailyThrsEntry |
1.3.6.1.4.1.664.2.8.4.5.1 |
| An entry in the DS0 Threshold Table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
AdDSUDPds0DailyThrsEntry |
|
|
| adDSUDPds0DailyThrsIndex |
1.3.6.1.4.1.664.2.8.4.5.1.1 |
| The index value which uniquely identifies the
DS0 interface to which this entry is applicable. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0DailyThrsUASs |
1.3.6.1.4.1.664.2.8.4.5.1.2 |
| The DS0 performance monitor Threshold Value for
the Daily Unavailable Seconds parameter. The
default value is 86, which equates to approximately
99.9% Availability for a Daily Interval. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0DailyThrsAvail |
1.3.6.1.4.1.664.2.8.4.5.1.3 |
| The DS0 performance monitor Threshold Value for
the percentage channel Availability parameter.
The default value is 9950 (% times 100), which equates
to 99.5% Availability for a Daily Interval. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0AlertEntry |
1.3.6.1.4.1.664.2.8.4.6.1 |
| An entry in the DS0 PM Alert Table |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
AdDSUDPds0AlertEntry |
|
|
| adDSUDPds0AlertIndex |
1.3.6.1.4.1.664.2.8.4.6.1.1 |
| The index value which uniquely identifies the
DS0 PM interface to which this entry is applicable. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0AlertStatus |
1.3.6.1.4.1.664.2.8.4.6.1.2 |
| This bit map variable indicates Threshold Crossing
Events for DS0 performance monitored parameters.
When a parameter exceeds its threshold value, the
parameter's bit is set in this variable. A SNMP
trap is generated if the parameter's alert enable
bit is set.
The alert event bit values are:
1 Interval UAS
2 Daily UAS
4 Daily percent Availability |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPds0AlertEnable |
1.3.6.1.4.1.664.2.8.4.6.1.3 |
| This bit map variable enables changes in the DS0
PM Alert Status to generate a SNMP Trap.
The alert enable bit values are:
1 Interval UAS
2 Daily UAS
4 Daily percent Availability |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPAlarmStatus |
1.3.6.1.4.1.664.2.8.5.1 |
| This bit map variable indicates changes in the DSUDP
status. When a status bit changes state, the
the corresponding bit is set in this variable.
The alarm event bit values are:
1 No Alarm
2 0
4 0
8 Self diagnostics failed
16 OOS/OOF from network
32 DSUDP Loopback
64 Channel Loopback
128 OCU Loopback |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPAlarmMajor |
1.3.6.1.4.1.664.2.8.5.2 |
| A bit mask to select items of the
AlarmStatus which represent a Major Alarm |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPAlarmMinor |
1.3.6.1.4.1.664.2.8.5.3 |
| A bit mask to select items of the
AlarmStatus which represent a Minor Alarm |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPAlarmAlert |
1.3.6.1.4.1.664.2.8.5.4 |
| A bit mask to select items of the
AlarmStatus which represent an Alert Alarm |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPAlarmInfo |
1.3.6.1.4.1.664.2.8.5.5 |
| A bit mask to select items of the
AlarmStatus which represent an Info Alarm |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPAlarmEnable |
1.3.6.1.4.1.664.2.8.5.6 |
| This bit map variable enables changes in the DSUDP
Alarm Status to generate a SNMP Trap.
The alarm enable bit values are:
1 0
2 0
4 0
8 Self diagnostics failed
16 OOS/OOF from network
32 DSUDP Loopback
64 Channel Loopback
128 OCU Loopback |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| adDSUDPNetworkINS |
808 |
| The network channel is In-Service. The OOS/OOF
condition has cleared. |
| TRAP-TYPE |
|
|
|
| adDSUDPThrsAlertIntUAS |
883 |
| The Interval Un-Available Seconds (UAS) parameter has
reached or exceeds its threshold value. |
| TRAP-TYPE |
|
|
|
| adDSUDPThrsAlertDailyUAS |
867 |
| The Daily Un-Available Seconds UAS parameter has
reached or exceeds its threshold value. |
| TRAP-TYPE |
|
|
|