ADH-NETCOM-MIB
File:
ADH-NETCOM-MIB.mib (7014 bytes)
Imported modules
Imported symbols
Defined Values
environmentalTechnology |
1.3.6.1.4.1.32185 |
The Structure of Management Information for
Environmental Technology Inc. SNMP devices |
MODULE-IDENTITY |
|
|
|
netcom |
1.3.6.1.4.1.32185.2 |
ADH NETCOM |
Status: current |
Access: read-write |
OBJECT-IDENTITY |
|
|
|
statusInfo |
1.3.6.1.4.1.32185.2.1 |
OBJECT IDENTIFIER |
|
|
|
paramsInfo |
1.3.6.1.4.1.32185.2.2 |
OBJECT IDENTIFIER |
|
|
|
allStatuses |
1.3.6.1.4.1.32185.2.1.1 |
Summary: same as objects 2-7, separated by semicolons |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(80) |
|
pressurePSI |
1.3.6.1.4.1.32185.2.1.2 |
Pressure, in PSI or mbar |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
dutycycle |
1.3.6.1.4.1.32185.2.1.3 |
Current duty cycle, in percent; --- if none available |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
statusVars |
1.3.6.1.4.1.32185.2.1.4 |
Summary of the status of the unit.
Is always 7 characters
Character 1 is super-state: govering whole system, if
this unit is a master
S=slave (not a master)
M=master; N=master but system off line
D=director; D=director but system off line
master: for redundant systems
director: for increasing pumping capability
Character 2 is major state: N=normal, S=standby, L=leaky
Character 3 is environment: N=normal, C=cold, H=hot
Character 4 is canister 1 condition:
O=OK (ie dry), F=full (wet), U=unknown, D=dead
Character 5 is canister 1 usage:
I=idle, U=in use, R=regenerating
Character 6 is canister 2 condition, as in character 4
Character 7 is canister 2 usage, as in character 5 |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(6) |
|
temperature |
1.3.6.1.4.1.32185.2.1.5 |
Current temperature, in degrees F or C |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
alarms |
1.3.6.1.4.1.32185.2.1.6 |
Current alarm conditions: is a list of them
Each character has a - for no alarm, or an A or W if there
is an alarm. A means alarm (serious), W means a warning
(not so serious). Severity levels may later change.
List of alarms: (later versions may add more):
A1: Low pressure
A2: High pressure
W3: High duty cycle
W4: High temperature
W5: Low temperature
W6: Unused
A7: Canister 1 won't heat
A8: Canister 1 won't cool
A9: Canister 2 won't heat
A10: Canister 2 won't cool
A11: Unable to pressurize
A12: Dew point alarm
W13: Compressor timeout (for future use)
W14: Communications error
A15: Canister 1 thermistor bad
A16: Canister 2 thermistor bad
A17: Ambient thermistor bad
A18: Overpressure
A19: Bad calibrations in EEPROM
A20: Bad limits in EEPROM
A21: Short cycling
A22: Pump shut down due to error condition |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(30) |
|
compressorHours |
1.3.6.1.4.1.32185.2.1.7 |
Number of hours that the compressor has been running;
resolution is tenths of an hour. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(30) |
|
majorState |
1.3.6.1.4.1.32185.2.1.8 |
Major state of the dehydrator.
Online: currently pressurizing.
Standby: not pressurizing.
Leaky: shut down because of inability to pressurize. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
online(1), standby(2), leaky(3) |
|
cycleTime |
1.3.6.1.4.1.32185.2.1.9 |
Time of last duty cycle in seconds;
0.0 means none available |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
lowerLimit |
1.3.6.1.4.1.32185.2.2.1 |
The pressure, in PSI or mbar,
at which the unit starts to pump |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
upperLimit |
1.3.6.1.4.1.32185.2.2.2 |
The pressure, in PSI or mbar, which the unit pressurizes to |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
lowerAlarmLimit |
1.3.6.1.4.1.32185.2.2.3 |
The pressure, in PSI or mbar,
below which the unit declares a low pressure alarm |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|
upperAlarmLimit |
1.3.6.1.4.1.32185.2.2.4 |
The pressure, in PSI or mbar,
above which the unit declares a high pressure alarm |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(10) |
|