ACP-MIB

File: ACP-MIB.mib (20087 bytes)

Imported modules

BCS-IDENT-MIB

SNMPv2-SMI

Imported symbols

giproducts

OBJECT-TYPE

MODULE-IDENTITY

Defined Types

AcpStatusEntry
SEQUENCE
	acpEncryptType	INTEGER
	acpUnitIndex	INTEGER
	acpServiceIndex	INTEGER
	acpScramblingMode	INTEGER
	acpUnitAddress	OCTET STRING
	acpInputInterface	INTEGER
	acpOutputInterface	INTEGER
	acpServNumber	INTEGER
	acpServAuthorization	INTEGER
	acpServAuthReaCode	INTEGER
	acpServEncryption	INTEGER
	acpCatSeqNums	INTEGER
	acpEmmCount	INTEGER
	acpProgramEpochNumber	INTEGER
	acpNextProgramEpochNumber	INTEGER
	acpNextServAuthorization	INTEGER
	acpNextServAuthReasonCode	INTEGER
	acpInputSourceIdA	INTEGER
	acpInputSourceIdB	INTEGER

AcpPidEntry
SEQUENCE
	acpPidTblEncryptType	INTEGER
	acpPidTblUnitIndex	INTEGER
	acpPidTblServiceIndex	INTEGER
	acpPidTblPidIndex	INTEGER
	acpPidTblAssignedPid	INTEGER
	acpPidTblEcmPid	INTEGER
	acpPidTblPidMask	INTEGER

Defined Values

acpStatus		1.3.6.1.4.1.1166.1.11
The MIB module for the Access Control Processor (TSODA, MC1). Revision Number 1.40
MODULE-IDENTITY

acpNumberofEncryptTypes		1.3.6.1.4.1.1166.1.11.1
The total number of encrypt type ACPs in the system.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpNumberofDecryptTypes		1.3.6.1.4.1.1166.1.11.2
The total number of decrypt type ACPs in the system.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpStatusTable		1.3.6.1.4.1.1166.1.11.3
A table of ACP entries giving health, status and mode
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AcpStatusEntry

acpStatusEntry		1.3.6.1.4.1.1166.1.11.3.1
A row in the ACP Entry Table
Status: current	Access: not-accessible
OBJECT-TYPE
	AcpStatusEntry

acpEncryptType		1.3.6.1.4.1.1166.1.11.3.1.1
The type of ACP in the system. It is either an encryptAcp or decryptAcp device.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	encryptAcp(1), decryptAcp(2)

acpUnitIndex		1.3.6.1.4.1.1166.1.11.3.1.2
The ACP unit index for this encrypt/decrypt type. For each type of ACP, encryptAcp or decryptAcp, the physical unit number of the ACP in the containing product, starting at 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

acpServiceIndex		1.3.6.1.4.1.1166.1.11.3.1.3
For a specified ACP, identified by the both acpEncryptType and acpUnitIndex, this index specifies the sequential service capabilities of this ACP, found in the following objects: acpServNumber acpServAuthorization acpServAuthReaCode acpServEncryption The maximum limit on the value of this index is determined by the Max number of services supported by this ACP (for a TSODA, it is 2). For all other objects in the acpStatusTable, this index is not used. (it must be valid, but will not be used to access the object uniquely specified by acpEncryptType and acpUnitIndex) REFERENCE
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

acpScramblingMode		1.3.6.1.4.1.1166.1.11.3.1.4
The Scrambling Mode of the ACP 1 - North American DES 2 - DVB Common Scrambling Algorithm
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	des(1), csa(2)

acpUnitAddress		1.3.6.1.4.1.1166.1.11.3.1.5
The 40 bit ACP address in Human-readable format 3-5-5-3
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

acpInputInterface		1.3.6.1.4.1.1166.1.11.3.1.6
The interface for MPEG input to this ACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	acpInterfaceSerial(1), acpInterfaceParallel(2)

acpOutputInterface		1.3.6.1.4.1.1166.1.11.3.1.7
The interface for MPEG output from this ACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	acpInterfaceSerial(1), acpInterfaceParallel(2)

acpServNumber		1.3.6.1.4.1.1166.1.11.3.1.8
MPEG service number (0=unknown) for encrypted service N, where N is specified by acpServiceIndex.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

acpServAuthorization		1.3.6.1.4.1.1166.1.11.3.1.9
ACP authorization status for service specified by acpServiceIndex
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unauthorized(1), authorized(2), unknown(255)

acpServAuthReaCode		1.3.6.1.4.1.1166.1.11.3.1.10
ACP authorization reason code for service specified By acpServiceIndex.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpServEncryption		1.3.6.1.4.1.1166.1.11.3.1.11
ACP encryption status for service specified by The index acpServiceIndex.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(255), fixedwk(1), fixedpk(2), unencrypted(3), fullencryption(4)

acpCatSeqNums		1.3.6.1.4.1.1166.1.11.3.1.12
The current and next Category Sequence Numbers
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpEmmCount		1.3.6.1.4.1.1166.1.11.3.1.13
The number of Category Rekey messages sent to this ACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpProgramEpochNumber		1.3.6.1.4.1.1166.1.11.3.1.14
The current program epoch number for the service on this side of the ACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpNextProgramEpochNumber		1.3.6.1.4.1.1166.1.11.3.1.15
The next program epoch number for the service on this side of the ACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpNextServAuthorization		1.3.6.1.4.1.1166.1.11.3.1.16
ACP authorization status for the next Program Epoch for the service specified by acpServiceIndex
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unauthorized(1), authorized(2), unknown(255)

acpNextServAuthReasonCode		1.3.6.1.4.1.1166.1.11.3.1.17
ACP authorization reason code for the next Program Epoch for the service specified By acpServiceIndex.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpInputSourceIdA		1.3.6.1.4.1.1166.1.11.3.1.18
The Input Source Id is used to identify the input source for this ACP in different products. One or both parts of the Id may be used in identifying where the input for the ACP comes from. When the Input Source Id A is set to 255 then the Id is invalid. If Id A is invalid the Id B is assumed invalid also. For example, the MPS uses the input source id to designate the location of the physical connector that is mapped to the ACP. In the case of the decrypt ACPs, InputSourceIdA is used to indicate the slot, and InputSourceIdB is used to indicate the port. Only decrypt ACPs have their source identified in this way. Encrypt ACPs do not have an identified source and their IdA is always set to Invalid (255).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpInputSourceIdB		1.3.6.1.4.1.1166.1.11.3.1.19
The Input Source Id is used to identify the input source for this ACP in different products. One or both parts of the Id may be used in identifying where the input for the ACP comes from. For example, the MPS uses the input source id to designate the location of the physical connector that is mapped to the ACP. In the case of the decrypt ACPs, InputSourceIdA is used to indicate the slot, and InputSourceIdB is used to indicate the port. Only decrypt ACPs have their source identified in this way. Encrypt ACPs do not have an identified source.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpPidTable		1.3.6.1.4.1.1166.1.11.4
A table of ACP entries giving assigned pid values
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AcpPidEntry

acpPidEntry		1.3.6.1.4.1.1166.1.11.4.1
A row in the ACP Pid Table
Status: current	Access: not-accessible
OBJECT-TYPE
	AcpPidEntry

acpPidTblEncryptType		1.3.6.1.4.1.1166.1.11.4.1.1
The type of ACP in the system. It is either an encryptAcp or decryptAcp device.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	encryptAcp(1), decryptAcp(2)

acpPidTblUnitIndex		1.3.6.1.4.1.1166.1.11.4.1.2
The ACP unit index for this encrypt/decrypt type. For each type of ACP, encryptAcp or decryptAcp, the physical unit number of the ACP in the containing product, starting at 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

acpPidTblServiceIndex		1.3.6.1.4.1.1166.1.11.4.1.3
For a specified ACP, identified by the both acpEncryptType and acpUnitIndex. The maximum limit on the value of this index is determined by the Max number of services supported by this ACP (for a TSODA, it is 2). For all other objects in the acpStatusTable, this index is not used. (it must be valid, but will not be used to access the object uniquely specified by acpEncryptType and acpUnitIndex)
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

acpPidTblPidIndex		1.3.6.1.4.1.1166.1.11.4.1.4
The PID index of the requested assigned PID value. multiple PIDs can be assigned per service
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

acpPidTblAssignedPid		1.3.6.1.4.1.1166.1.11.4.1.5
The PID assigned. If 0x1fff is returned then no PID is assigned.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpPidTblEcmPid		1.3.6.1.4.1.1166.1.11.4.1.6
The ECM PID cooresponding to the assigned PID. Value set to 0x1fff when no ECM PID is programmed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpPidTblPidMask		1.3.6.1.4.1.1166.1.11.4.1.7
The PID mask used in conjunction with the assigned PID. Bits that are set in the PID Mask field of the ACP are 'dont cares' when comparing the PID of a received packet to the PID value configured in the ACP. For example, if the PID 0x0040 is configured in the ACP and the PID Mask is set to 0x000F, then any received packet with a PID from 0x0040 to 0x004F inclusive will be processed by the ACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

acpMibRevision		1.3.6.1.4.1.1166.1.11.99
The current revision number of acp.mib multiplied by 100. To extract the major revision number divide by 100. The remainder is the minor revision number. The major rev number should be bumped whenever structural changes occur that require coresponding manager changes. Small changes like editing a description should bump the minor rev. The mib revision is matches the one found at the top of acp.mib
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER