ACD-SA-MIB

File: ACD-SA-MIB.mib (40076 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
ACCEDIAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Gauge32 DisplayString DateAndTime
TEXTUAL-CONVENTION RowStatus MODULE-COMPLIANCE
OBJECT-GROUP acdMibs

Defined Types

AcdSaMetricType  
A value that represents a type of metric that can be used in an instance of Service Availability.
TEXTUAL-CONVENTION    
  INTEGER metricPaaPlr(1), metricPaaOwDelay(2), metricPaaOwDv(3), metricPaaTwDelay(4), metricPaaTwDv(5), metricCfmPlr(6), metricCfmOwDelay(7), metricCfmOwDv(8), metricCfmTwDelay(9), metricCfmTwDv(10), metricCfmSlmNearEndPlr(11), metricCfmSlmFarEndPlr(12)  

AcdSaValidFlag  
The validity flag can have three values: valid, adjusted, or pending. The value of valid indicates the metrics are calculated normally. The value of adjusted is used to indicate a change occurred in the configuration during the reporting period which may impact the service availability calculation. The value of pending indicates that the counters were reset in the middle of a time interval.
TEXTUAL-CONVENTION    
  INTEGER valid(1), adjusted(2), pending(3)  

AcdSaAdminStateFlag  
This flag is used for the administrative state. The value IS indicates the state is In-Service. The value OOS indicates the state is Out-of-Service.
TEXTUAL-CONVENTION    
  INTEGER is(1), oos(2)  

AcdSaOperStateFlag  
This flag is used for the operational state. The value IS indicates the state is In-Service. The value OOS indicates the state is Out-of-Service. The value oos-au indicates the state is Out-of-Service-Autonomous. This state is entered when all of the metrics associated with the service instance are disabled.
TEXTUAL-CONVENTION    
  INTEGER is(1), oos(2), oosAu(3)  

AcdSaServiceConfigEntry  
SEQUENCE    
  acdSaServiceIndex Unsigned32
  acdSaServiceConfigRowStatus RowStatus
  acdSaServiceConfigName DisplayString
  acdSaServiceConfigAdminState AcdSaAdminStateFlag
  acdSaServiceConfigReportingPeriod Unsigned32
  acdSaServiceConfigUaWindowSize Unsigned32
  acdSaServiceConfigHliWindowSize Unsigned32
  acdSaServiceConfigTimeInterval Unsigned32

AcdSaMetricConfigEntry  
SEQUENCE    
  acdSaMetricIndex Unsigned32
  acdSaMetricConfigRowStatus RowStatus
  acdSaMetricConfigName DisplayString
  acdSaMetricConfigSrcName DisplayString
  acdSaMetricConfigType AcdSaMetricType
  acdSaMetricConfigThreshold Unsigned32

AcdSaServiceCounterEntry  
SEQUENCE    
  acdSaServiceCounterPeriodIndex Unsigned32
  acdSaServiceCounterValidFlag AcdSaValidFlag
  acdSaServiceCounterUpTime Unsigned32
  acdSaServiceCounterUaTime Unsigned32
  acdSaServiceCounterMaintTime Unsigned32
  acdSaServiceCounterAvailRatio Unsigned32
  acdSaServiceCounterGaps Unsigned32
  acdSaServiceCounterLargestGap Unsigned32
  acdSaServiceCounterChliTime Unsigned32
  acdSaServiceCounterChliRatio Unsigned32

AcdSaServiceHistCounterEntry  
SEQUENCE    
  acdSaServiceHistCounterPeriodIndex Unsigned32
  acdSaServiceHistCounterIntervalEnd DateAndTime
  acdSaServiceHistCounterValidFlag AcdSaValidFlag
  acdSaServiceHistCounterUpTime Unsigned32
  acdSaServiceHistCounterUaTime Unsigned32
  acdSaServiceHistCounterMaintTime Unsigned32
  acdSaServiceHistCounterAvailRatio Unsigned32
  acdSaServiceHistCounterGaps Unsigned32
  acdSaServiceHistCounterLargestGap Unsigned32
  acdSaServiceHistCounterChliTime Unsigned32
  acdSaServiceHistCounterChliRatio Unsigned32

AcdSaServiceMonoCounterEntry  
SEQUENCE    
  acdSaServiceMonoCounterValidFlag AcdSaValidFlag
  acdSaServiceMonoCounterUpTime Unsigned32
  acdSaServiceMonoCounterUaTime Unsigned32
  acdSaServiceMonoCounterMaintTime Unsigned32
  acdSaServiceMonoCounterAvailRatio Unsigned32
  acdSaServiceMonoCounterGaps Unsigned32
  acdSaServiceMonoCounterLargestGap Unsigned32
  acdSaServiceMonoCounterChliTime Unsigned32
  acdSaServiceMonoCounterChliRatio Unsigned32

AcdSaMetricCounterEntry  
SEQUENCE    
  acdSaMetricCounterValidFlag AcdSaValidFlag
  acdSaMetricCounterUaTime Unsigned32
  acdSaMetricCounterChliTime Unsigned32

AcdSaMetricHistCounterEntry  
SEQUENCE    
  acdSaMetricHistCounterID Unsigned32
  acdSaMetricHistCounterPeriodIndex Unsigned32
  acdSaMetricHistCounterIntervalEnd DateAndTime
  acdSaMetricHistCounterValidFlag AcdSaValidFlag
  acdSaMetricHistCounterUaTime Unsigned32
  acdSaMetricHistCounterChliTime Unsigned32

AcdSaMetricMonoCounterEntry  
SEQUENCE    
  acdSaMetricMonoCounterValidFlag AcdSaValidFlag
  acdSaMetricMonoCounterUaTime Unsigned32
  acdSaMetricMonoCounterChliTime Unsigned32

AcdSaServiceStatusEntry  
SEQUENCE    
  acdSaServiceStatusID Unsigned32
  acdSaServiceStatusName DisplayString
  acdSaServiceStatusAdminState AcdSaAdminStateFlag
  acdSaServiceStatusOperState AcdSaOperStateFlag
  acdSaServiceStatusNbrMetrics Gauge32

Defined Values

acdSa 1.3.6.1.4.1.22420.2.12
The Service Availability database for this Accedian Networks device.
MODULE-IDENTITY    

acdSaNotifications 1.3.6.1.4.1.22420.2.12.0
OBJECT IDENTIFIER    

acdSaMIBObjects 1.3.6.1.4.1.22420.2.12.1
OBJECT IDENTIFIER    

acdSaConformance 1.3.6.1.4.1.22420.2.12.2
OBJECT IDENTIFIER    

acdSaConfig 1.3.6.1.4.1.22420.2.12.1.1
OBJECT IDENTIFIER    

acdSaCounter 1.3.6.1.4.1.22420.2.12.1.2
OBJECT IDENTIFIER    

acdSaStatus 1.3.6.1.4.1.22420.2.12.1.3
OBJECT IDENTIFIER    

acdSaServiceConfigTable 1.3.6.1.4.1.22420.2.12.1.1.1
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaServiceConfigEntry

acdSaServiceConfigEntry 1.3.6.1.4.1.22420.2.12.1.1.1.1
An entry consisting of all settings for a Service.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaServiceConfigEntry  

acdSaServiceIndex 1.3.6.1.4.1.22420.2.12.1.1.1.1.1
Unique value for each service instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

acdSaServiceConfigRowStatus 1.3.6.1.4.1.22420.2.12.1.1.1.1.2
All columns must have a valid value before a row can be activated. To create a new Service you shall provide a unique name for an empty row with the RowStatus set to Create and Go.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

acdSaServiceConfigName 1.3.6.1.4.1.22420.2.12.1.1.1.1.3
A unique name used to identify the Service.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

acdSaServiceConfigAdminState 1.3.6.1.4.1.22420.2.12.1.1.1.1.4
Administrative state is(1) or oos(2).
Status: current Access: read-write
OBJECT-TYPE    
  AcdSaAdminStateFlag  

acdSaServiceConfigReportingPeriod 1.3.6.1.4.1.22420.2.12.1.1.1.1.5
A reporting period over which availability counters are evaluated in addition to the monotonic counters (In minutes).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..1440  

acdSaServiceConfigUaWindowSize 1.3.6.1.4.1.22420.2.12.1.1.1.1.6
The number of consecutive seconds over which to assess unavailability.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..1000  

acdSaServiceConfigHliWindowSize 1.3.6.1.4.1.22420.2.12.1.1.1.1.7
The number of consecutive Time Intervals used to assess High Loss Intervals for this instance.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..999  

acdSaServiceConfigTimeInterval 1.3.6.1.4.1.22420.2.12.1.1.1.1.8
The interval of time during which the metric is evaluated. Allowed values are 1, 5, 10, 20, or 60.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60  

acdSaMetricConfigTable 1.3.6.1.4.1.22420.2.12.1.1.2
The .....
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaMetricConfigEntry

acdSaMetricConfigEntry 1.3.6.1.4.1.22420.2.12.1.1.2.1
An entry consisting of all settings for a Metric.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaMetricConfigEntry  

acdSaMetricIndex 1.3.6.1.4.1.22420.2.12.1.1.2.1.1
Index for each metric instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

acdSaMetricConfigRowStatus 1.3.6.1.4.1.22420.2.12.1.1.2.1.2
All columns must have a valid value before a row can be activated. To create a new Service you shall provide the a unique name for an empty row with the RowStatus set to Create and Go. To delete the VLAN set you need to set the RowStatus to destroy.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

acdSaMetricConfigName 1.3.6.1.4.1.22420.2.12.1.1.2.1.3
A unique name used to identify the Metric.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

acdSaMetricConfigSrcName 1.3.6.1.4.1.22420.2.12.1.1.2.1.4
A unique name used to identify the source metric.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

acdSaMetricConfigType 1.3.6.1.4.1.22420.2.12.1.1.2.1.5
Enable or disable the Service Availability entry.
Status: current Access: read-write
OBJECT-TYPE    
  AcdSaMetricType  

acdSaMetricConfigThreshold 1.3.6.1.4.1.22420.2.12.1.1.2.1.6
Indicates the delay threshold for this metric when type is one of metric delay parameters (in micro-seconds). Indicates the packet loss threshold for this metric when type is one of packet-loss parameter expressed in millionth of percent (1,000,000 is 1%).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterTable 1.3.6.1.4.1.22420.2.12.1.2.1
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaServiceCounterEntry

acdSaServiceCounterEntry 1.3.6.1.4.1.22420.2.12.1.2.1.1
An entry consisting of all counters for a Service.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaServiceCounterEntry  

acdSaServiceCounterPeriodIndex 1.3.6.1.4.1.22420.2.12.1.2.1.1.1
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same service instance. This index starts at 1 and increases by one as each new period.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterValidFlag 1.3.6.1.4.1.22420.2.12.1.2.1.1.2
Indicates the validity of the service counter during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaValidFlag  

acdSaServiceCounterUpTime 1.3.6.1.4.1.22420.2.12.1.2.1.1.3
Uptime is a measure of the time a service has been up during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterUaTime 1.3.6.1.4.1.22420.2.12.1.2.1.1.4
The UaTime is a measure of the time a service has been unavailable during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterMaintTime 1.3.6.1.4.1.22420.2.12.1.2.1.1.5
The MaintTime is a measure of the time a service has been in maintenance during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterAvailRatio 1.3.6.1.4.1.22420.2.12.1.2.1.1.6
Indicates the availability ratio in millionth of a percent (1,000,000 is 1%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000000  

acdSaServiceCounterGaps 1.3.6.1.4.1.22420.2.12.1.2.1.1.7
The gap shall be the number of time the state change from available to unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterLargestGap 1.3.6.1.4.1.22420.2.12.1.2.1.1.8
The largest gap shall be the largest number of consecutive unavailable second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterChliTime 1.3.6.1.4.1.22420.2.12.1.2.1.1.9
The CHLI time is a counter which increments for every high loss interval. It is only reset to zero when one of the following conditions occur: 1) device reboot 2) explicit counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceCounterChliRatio 1.3.6.1.4.1.22420.2.12.1.2.1.1.10
The ratio of high loss intervals divided by the uptime minus the sum of maintenance time and unavailable time, expressed in millionth of a percent (1,000,000 is 1%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000000  

acdSaServiceHistCounterTable 1.3.6.1.4.1.22420.2.12.1.2.2
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaServiceHistCounterEntry

acdSaServiceHistCounterEntry 1.3.6.1.4.1.22420.2.12.1.2.2.1
An entry consisting of all counters for a Service.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaServiceHistCounterEntry  

acdSaServiceHistCounterPeriodIndex 1.3.6.1.4.1.22420.2.12.1.2.2.1.1
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same service instance. This index starts at 1 and increases by one as each new period.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterIntervalEnd 1.3.6.1.4.1.22420.2.12.1.2.2.1.2
This is the time of the end of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

acdSaServiceHistCounterValidFlag 1.3.6.1.4.1.22420.2.12.1.2.2.1.3
Indicates the validity of the service counter during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaValidFlag  

acdSaServiceHistCounterUpTime 1.3.6.1.4.1.22420.2.12.1.2.2.1.4
Uptime is a measure of the time a service has been up during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterUaTime 1.3.6.1.4.1.22420.2.12.1.2.2.1.5
The UaTime is a measure of the time a service has been unavailable during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterMaintTime 1.3.6.1.4.1.22420.2.12.1.2.2.1.6
The MaintTime is a measure of the time a service has been in maintenance during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterAvailRatio 1.3.6.1.4.1.22420.2.12.1.2.2.1.7
Indicates the availability ratio in millionth of a percent (1,000,000 is 1%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000000  

acdSaServiceHistCounterGaps 1.3.6.1.4.1.22420.2.12.1.2.2.1.8
The gap shall be the number of time the state change from available to unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterLargestGap 1.3.6.1.4.1.22420.2.12.1.2.2.1.9
The largest gap shall be the largest number of consecutive unavailable second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterChliTime 1.3.6.1.4.1.22420.2.12.1.2.2.1.10
The CHLI time is a counter which increments for every High Loss Interval. It is only reset to zero when one of the following conditions occur: 1) device reboot 2) explicit counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceHistCounterChliRatio 1.3.6.1.4.1.22420.2.12.1.2.2.1.11
The ratio of high loss intervals divided by the uptime minus the sum of maintenance time and unavailable time, expressed in millionth of a percent (1,000,000 is 1%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000000  

acdSaServiceMonoCounterTable 1.3.6.1.4.1.22420.2.12.1.2.3
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaServiceMonoCounterEntry

acdSaServiceMonoCounterEntry 1.3.6.1.4.1.22420.2.12.1.2.3.1
An entry consisting of all monotonic counters for a Service.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaServiceMonoCounterEntry  

acdSaServiceMonoCounterValidFlag 1.3.6.1.4.1.22420.2.12.1.2.3.1.1
Indicates the validity of the service counter during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaValidFlag  

acdSaServiceMonoCounterUpTime 1.3.6.1.4.1.22420.2.12.1.2.3.1.2
Uptime is a measure of the time a service has been up during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceMonoCounterUaTime 1.3.6.1.4.1.22420.2.12.1.2.3.1.3
The UaTime is a measure of the time a service has been unavailable during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceMonoCounterMaintTime 1.3.6.1.4.1.22420.2.12.1.2.3.1.4
The MaintTime is a measure of the time a service has been in maintenance during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceMonoCounterAvailRatio 1.3.6.1.4.1.22420.2.12.1.2.3.1.5
Indicates the availability ratio in millionth of a percent (1,000,000 is 1%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000000  

acdSaServiceMonoCounterGaps 1.3.6.1.4.1.22420.2.12.1.2.3.1.6
The gap shall be the number of time the state change from available to unavailable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceMonoCounterLargestGap 1.3.6.1.4.1.22420.2.12.1.2.3.1.7
The largest gap shall be the largest number of consecutive unavailable second.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceMonoCounterChliTime 1.3.6.1.4.1.22420.2.12.1.2.3.1.8
A counter which increments for every high loss interval. It is only reset to zero when one of the following conditions occur: 1) device reboot 2) explicit counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceMonoCounterChliRatio 1.3.6.1.4.1.22420.2.12.1.2.3.1.9
The ratio of high loss intervals divided by the uptime minus the sum of maintenance time and unavailable time, expressed in millionth of a percent (1,000,000 is 1%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000000  

acdSaMetricCounterTable 1.3.6.1.4.1.22420.2.12.1.2.4
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaMetricCounterEntry

acdSaMetricCounterEntry 1.3.6.1.4.1.22420.2.12.1.2.4.1
An entry consisting of all counters for a Metric.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaMetricCounterEntry  

acdSaMetricCounterValidFlag 1.3.6.1.4.1.22420.2.12.1.2.4.1.1
Indicates the validity of the metric counter during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaValidFlag  

acdSaMetricCounterUaTime 1.3.6.1.4.1.22420.2.12.1.2.4.1.2
The UaTime is a measure of the time a metric has been unavailable during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaMetricCounterChliTime 1.3.6.1.4.1.22420.2.12.1.2.4.1.3
A counter which increments for every High Loss Interval. It is only reset to zero when one of the following conditions occur: 1) device reboot 2) explicit counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaMetricHistCounterTable 1.3.6.1.4.1.22420.2.12.1.2.5
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaMetricHistCounterEntry

acdSaMetricHistCounterEntry 1.3.6.1.4.1.22420.2.12.1.2.5.1
An entry consisting of all counters for a Metric.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaMetricHistCounterEntry  

acdSaMetricHistCounterID 1.3.6.1.4.1.22420.2.12.1.2.5.1.1
Unique value for each Metric instance. This value follows the ordering of the service table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

acdSaMetricHistCounterPeriodIndex 1.3.6.1.4.1.22420.2.12.1.2.5.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same service instance. This index starts at 1 and increases by one as each new period.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

acdSaMetricHistCounterIntervalEnd 1.3.6.1.4.1.22420.2.12.1.2.5.1.3
This is the time of the end of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

acdSaMetricHistCounterValidFlag 1.3.6.1.4.1.22420.2.12.1.2.5.1.4
Indicates the validity of the metric counter during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaValidFlag  

acdSaMetricHistCounterUaTime 1.3.6.1.4.1.22420.2.12.1.2.5.1.5
The UaTime is a measure of the time a metric has been unavailable during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaMetricHistCounterChliTime 1.3.6.1.4.1.22420.2.12.1.2.5.1.6
A counter which increments for every High Loss Interval. It is only reset to zero when one of the following conditions occur: 1) device reboot 2) explicit counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaMetricMonoCounterTable 1.3.6.1.4.1.22420.2.12.1.2.6
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaMetricMonoCounterEntry

acdSaMetricMonoCounterEntry 1.3.6.1.4.1.22420.2.12.1.2.6.1
An entry consisting of all counters for a Metric.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaMetricMonoCounterEntry  

acdSaMetricMonoCounterValidFlag 1.3.6.1.4.1.22420.2.12.1.2.6.1.1
Indicates the validity of the metric counter during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaValidFlag  

acdSaMetricMonoCounterUaTime 1.3.6.1.4.1.22420.2.12.1.2.6.1.2
The UaTime is a measure of the time a metric has been unavailable during this sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaMetricMonoCounterChliTime 1.3.6.1.4.1.22420.2.12.1.2.6.1.3
A counter which increments for every high loss interval. It is only reset to zero when one of the following conditions occur: 1) device reboot 2) explicit counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

acdSaServiceStatusTable 1.3.6.1.4.1.22420.2.12.1.3.1
This table contains all instance of service availability of this unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcdSaServiceStatusEntry

acdSaServiceStatusEntry 1.3.6.1.4.1.22420.2.12.1.3.1.1
An entry consisting of all status for a Service.
Status: current Access: not-accessible
OBJECT-TYPE    
  AcdSaServiceStatusEntry  

acdSaServiceStatusID 1.3.6.1.4.1.22420.2.12.1.3.1.1.1
Unique value for each service instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

acdSaServiceStatusName 1.3.6.1.4.1.22420.2.12.1.3.1.1.2
A unique name used to identify the Service.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

acdSaServiceStatusAdminState 1.3.6.1.4.1.22420.2.12.1.3.1.1.3
Administrative state is one of is(1) or oos(2).
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaAdminStateFlag  

acdSaServiceStatusOperState 1.3.6.1.4.1.22420.2.12.1.3.1.1.4
Operational state is one of is(1), oos(2) or oosAu (3).
Status: current Access: read-only
OBJECT-TYPE    
  AcdSaOperStateFlag  

acdSaServiceStatusNbrMetrics 1.3.6.1.4.1.22420.2.12.1.3.1.1.5
The number of metrics associated with this Service instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

acdSaCompliances 1.3.6.1.4.1.22420.2.12.2.1
OBJECT IDENTIFIER    

acdSaGroups 1.3.6.1.4.1.22420.2.12.2.2
OBJECT IDENTIFIER    

acdSaServiceConfigGroup 1.3.6.1.4.1.22420.2.12.2.2.1
Objects for the Service configuration Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaMetricConfigGroup 1.3.6.1.4.1.22420.2.12.2.2.2
Objects for the Metric configuration Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaServiceCounterGroup 1.3.6.1.4.1.22420.2.12.2.2.3
Objects for the Service Counter Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaServiceHistCounterGroup 1.3.6.1.4.1.22420.2.12.2.2.4
Objects for the Service History Counter Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaServiceMonoCounterGroup 1.3.6.1.4.1.22420.2.12.2.2.5
Objects for the Service Monotonic Counter Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaMetricCounterGroup 1.3.6.1.4.1.22420.2.12.2.2.6
Objects for the Metric Counter Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaMetricHistCounterGroup 1.3.6.1.4.1.22420.2.12.2.2.7
Objects for the Metric History Counter Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaMetricMonoCounterGroup 1.3.6.1.4.1.22420.2.12.2.2.8
Objects for the Metric History Counter Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaServiceStatusGroup 1.3.6.1.4.1.22420.2.12.2.2.9
Objects for the Service Status Group.
Status: current Access: read-only
OBJECT-GROUP    

acdSaCompliance 1.3.6.1.4.1.22420.2.12.2.1.1
The compliance statement for support of the ACD-SA-MIB module.
Status: current Access: read-only
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor