ACC-MSP

File: ACC-MSP.mib (16165 bytes)

Imported modules

RFC1155-SMI RFC-1215 ACC-SYSTEM
ACC-MIB

Imported symbols

OBJECT-TYPE IpAddress TimeTicks
Gauge Counter TRAP-TYPE
accTrapLogSeqNum accBRG DisplayString
RowStatus IfIndex SmdsAddress

Defined Types

AccMspNeighborEntry  
SEQUENCE    
  accMspNeighborAddress IpAddress
  accMspNeighborIDs Counter
  accMspNeighborVersions Counter
  accMspNeighborStates Counter
  accMspNeighborAckTimeOuts Counter
  accMspNeighborRetransmissions Counter

Defined Values

accMsp 1.3.6.1.4.1.5.1.1.76
OBJECT IDENTIFIER    

accMspGeneralScalars 1.3.6.1.4.1.5.1.1.76.1
OBJECT IDENTIFIER    

accMspNeighbor 1.3.6.1.4.1.5.1.1.76.2
OBJECT IDENTIFIER    

accMspTraps 1.3.6.1.4.1.5.1.1.76.3
OBJECT IDENTIFIER    

accMspTrapMsg 1.3.6.1.4.1.5.1.1.76.3.1
Enterprise Trap Message for Msp
OBJECT-TYPE    
  DisplayString  

accMspAdminState 1.3.6.1.4.1.5.1.1.76.1.1
MSP Adminstrative state.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

accMspMode 1.3.6.1.4.1.5.1.1.76.1.2
MSP Mode : WAIT means that MSP requires its neighbors to respond only if they want the call. ACKNOWLEDGE causes all the MSP neighbors to respond to every request
OBJECT-TYPE    
  INTEGER wait(1), acknowledge(2)  

accMspDelivery 1.3.6.1.4.1.5.1.1.76.1.3
Sets the delivery mechanism for MSP packets.
OBJECT-TYPE    
  INTEGER multicast(1), limited-broadcast(2)  

accMspGroupId 1.3.6.1.4.1.5.1.1.76.1.4
MSP Group Identifier, should be the same value on all MSP NASs.
OBJECT-TYPE    
  INTEGER 0..16777216  

accMspInterfaceAddress 1.3.6.1.4.1.5.1.1.76.1.5
The interface address in which the MSP protocol is to operate over
OBJECT-TYPE    
  IpAddress  

accMspUdpPort 1.3.6.1.4.1.5.1.1.76.1.6
Changes the default UDP port number that MSP uses when sending and listening for MSP packets.
OBJECT-TYPE    
  INTEGER 1..65535  

accMspMaximumTimeout 1.3.6.1.4.1.5.1.1.76.1.7
Maximum amount of time MSP will wait for an MSP neighbor to respond to a request.
OBJECT-TYPE    
  INTEGER 50..100000  

accMspMaximumRetransmissions 1.3.6.1.4.1.5.1.1.76.1.8
Used to configure the maximum number of retransmissions that MSP will send to an MSP neighbor before designating the neighbors as 'non-responding'.
OBJECT-TYPE    
  INTEGER 0..10  

accMspMaximumHistorySize 1.3.6.1.4.1.5.1.1.76.1.9
Used to configure the maximum history buffer size. Must be in powers of 2.
OBJECT-TYPE    
  INTEGER 1..256  

accMspMessageLevel 1.3.6.1.4.1.5.1.1.76.1.10
Used to set the message level for MSP. 7 being most robust.
OBJECT-TYPE    
  INTEGER 1..7  

accMspDebugMask 1.3.6.1.4.1.5.1.1.76.1.11
Used to selectively enable and disable MSP trap messages used for debugging. The debug messages are different from regular traps.
OBJECT-TYPE    
  INTEGER 0..255  

accMspStatInPackets 1.3.6.1.4.1.5.1.1.76.1.12
Indicates the total number of MSP packets received from all MSP neighbors, both unicast and multicast packets.
OBJECT-TYPE    
  Counter  

accMspStatOutPackets 1.3.6.1.4.1.5.1.1.76.1.13
Indicates the total number of MSP packets sent, including both unicast and multicast packets.
OBJECT-TYPE    
  Counter  

accMspStatInQueries 1.3.6.1.4.1.5.1.1.76.1.14
Indicates the number of MSP Query Requests that have been received from MSP neighbors.
OBJECT-TYPE    
  Counter  

accMspStatOutQueries 1.3.6.1.4.1.5.1.1.76.1.15
Indicates the number of MSP Query requests that have been sent by this RAC. A MSP Query request is sent for each new Multilink call that the RAC receives.
OBJECT-TYPE    
  Counter  

accMspStatInAcks 1.3.6.1.4.1.5.1.1.76.1.16
Indicates the number of MSP acknowledge packets received by this RAC
OBJECT-TYPE    
  Counter  

accMspStatOutAcks 1.3.6.1.4.1.5.1.1.76.1.17
Indicates the number of MSP acknowledges sent by this RAC.
OBJECT-TYPE    
  Counter  

accMspStatInRequests 1.3.6.1.4.1.5.1.1.76.1.18
Indicates the number of times a MSP neighbor has requested a remote client session from this RAC.
OBJECT-TYPE    
  Counter  

accMspStatOutRequests 1.3.6.1.4.1.5.1.1.76.1.19
Indicates the number of times This RAC has requested a remote client session from a MSP neighbor.
OBJECT-TYPE    
  Counter  

accMspStatInDiscards 1.3.6.1.4.1.5.1.1.76.1.20
Indicates the number of times the local MSP protocol has discarded MSP packets.This counter increases if MSP receives a MSP packet that is not a member of its group. This counter will also increase whenever a MSP packet fails to be processed.
OBJECT-TYPE    
  Counter  

accMspStatProcessingErrors 1.3.6.1.4.1.5.1.1.76.1.21
Indicates the number of times the MSP protocol has failed to process a MSP packet. Failures arise from conditions where the packet could not be correctly processed, possibly because of resource limitations.
OBJECT-TYPE    
  Counter  

accMspStatNotForMes 1.3.6.1.4.1.5.1.1.76.1.22
Indicates number of times an MSP acknowledgment to a query not generated by this RAC has been received by this MSP protocol entity. This is normal for piggybacked responses, which are broadcast to the entire MSP community comprising the virtual machine.
OBJECT-TYPE    
  Counter  

accMspStatProtocolErrors 1.3.6.1.4.1.5.1.1.76.1.23
Indicates the number of times this MSP protocol entity has encountered MSP protocol errors in processing a MSP packet.
OBJECT-TYPE    
  Counter  

accMspStatInQueryPiggys 1.3.6.1.4.1.5.1.1.76.1.24
Along with Out Query Piggy, In Ack Piggy, and Out Ack Piggy indicates how well MSP is operating. As MSP activity increases, the MSP protocol is designed to piggyback Query Requests and Query Acknowledgments in the same response packet to optimize network traffic and to address scaling issues.
OBJECT-TYPE    
  Counter  

accMspStatOutQueryPiggys 1.3.6.1.4.1.5.1.1.76.1.25
Along with Out Query Piggy, In Ack Piggy, and Out Ack Piggy indicates how well MSP is operating. As MSP activity increases, the MSP protocol is designed to piggyback Query Requests and Query Acknowledgments in the same response packet to optimize network traffic and to address scaling issues.
OBJECT-TYPE    
  Counter  

accMspStatInAckPiggys 1.3.6.1.4.1.5.1.1.76.1.26
Along with Out Query Piggy, In Ack Piggy, and Out Ack Piggy indicates how well MSP is operating. As MSP activity increases, the MSP protocol is designed to piggyback Query Requests and Query Acknowledgments in the same response packet to optimize network traffic and to address scaling issues.
OBJECT-TYPE    
  Counter  

accMspStatOutAckPiggys 1.3.6.1.4.1.5.1.1.76.1.27
Along with Out Query Piggy, In Ack Piggy, and Out Ack Piggy indicates how well MSP is operating. As MSP activity increases, the MSP protocol is designed to piggyback Query Requests and Query Acknowledgments in the same response packet to optimize network traffic and to address scaling issues.
OBJECT-TYPE    
  Counter  

accMspStatQueryTimeouts 1.3.6.1.4.1.5.1.1.76.1.28
Indicates the number of times the local MSP protocol entity has timed out while waiting for a query response. This is normal in TIMEOUT mode of operation. However, if an excessive number of timeouts are indicated in ACKNOWLEDGE mode, there may be a problem with a particular RAC or excessive network traffic may be resulting in lost packets.
OBJECT-TYPE    
  Counter  

accMspStatMemoryFails 1.3.6.1.4.1.5.1.1.76.1.29
Indicates the number of times this MSP protocol entity has failed to acquire memory when performing its protocol operations.
OBJECT-TYPE    
  Counter  

accMspStatAverageQueryClosure 1.3.6.1.4.1.5.1.1.76.1.30
Indicates the average time to close a MSP Query Request. When in TIMEOUT mode, this value coincides with the configured maximum timeout parameter value. The default value for this parameter is 100 ms. In ACKNOWLEDGE mode, this value varies and usually is a good indicator of MSP responsiveness. A 'good' response time would be less than the configured timeout interval.
OBJECT-TYPE    
  Gauge  

accMspStatCurrentTimeout 1.3.6.1.4.1.5.1.1.76.1.31
indicates the current timeout value being used. In TIMEOUT mode, this will always be the maximum timeout value. In ACKNOWLEDGE mode, this value varies, but in steady state, it should be close to the Average Closure interval. If it is not, and this value continues to vary, it may indicate MSP activity problems such as high packet loss due to network congestion.
OBJECT-TYPE    
  Gauge  

accMspNeighborTable 1.3.6.1.4.1.5.1.1.76.2.1
Displays all active MSP Neighbors.
OBJECT-TYPE    
  SEQUENCE OF  
    AccMspNeighborEntry

accMspNeighborEntry 1.3.6.1.4.1.5.1.1.76.2.1.1
Tok_String
OBJECT-TYPE    
  AccMspNeighborEntry  

accMspNeighborAddress 1.3.6.1.4.1.5.1.1.76.2.1.1.1
The remote IP Address of the MSP Neighbor.
OBJECT-TYPE    
  IpAddress  

accMspNeighborIDs 1.3.6.1.4.1.5.1.1.76.2.1.1.2
Number of times the MSP Neighbor failed to respond to an MSP request
OBJECT-TYPE    
  Counter  

accMspNeighborVersions 1.3.6.1.4.1.5.1.1.76.2.1.1.3
Tok_String
OBJECT-TYPE    
  Counter  

accMspNeighborStates 1.3.6.1.4.1.5.1.1.76.2.1.1.4
Tok_String
OBJECT-TYPE    
  Counter  

accMspNeighborAckTimeOuts 1.3.6.1.4.1.5.1.1.76.2.1.1.5
Tok_String
OBJECT-TYPE    
  Counter  

accMspNeighborRetransmissions 1.3.6.1.4.1.5.1.1.76.2.1.1.6
Tok_String
OBJECT-TYPE    
  Counter  

accMspIpBindTrap 1
When the MSP multi cast binding to a IP is attempted, if this fails then this trap is generated. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accMspTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    

accMspInvIntfAddrTrap 2
if The MSP interface address is not 0.0.0.0 then only it is a valid interface address. So, if this check fails this trap is generated SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accMspTrapMsg } PCAUSE-DEFAULT: 7
TRAP-TYPE    

accMspShutdownTrap 3
While creating a MSP neighbor, if the allocation to that fails due to allocc failure, then this is REAL bad situation as this could break the hello protocol. MSP has to be SHUTDOWN SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accMspTrapMsg } PCAUSE-DEFAULT: 32
TRAP-TYPE