AC-PSTN-MIB

File: AC-PSTN-MIB.mib (52583 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1155-SMI
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB SNMPv2-CONF
AUDIOCODES-TYPES-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY TAddress
DisplayString DateAndTime TEXTUAL-CONVENTION
IpAddress Unsigned32 Integer32
enterprises RowStatus SnmpAdminString
InetAddressType InetAddress MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP audioCodes
acRegistrations acGeneric acProducts
acBoardMibs

Defined Types

AcTrunkEntry  
SEQUENCE    
  acTrunkIndex Unsigned32
  acTrunkAdministrativeState INTEGER
  acTrunkProtocolType INTEGER
  acTrunkClockMaster INTEGER
  acTrunkFramingMethod INTEGER
  acTrunkLineCode INTEGER
  acTrunkTraceLevel INTEGER
  acTrunkDialPlanName SnmpAdminString
  acTrunkLineType INTEGER
  acTrunkAutoClockPriority Unsigned32
  acTrunkDeactivate INTEGER

AcTrunkLineEntry  
SEQUENCE    
  acTrunkLineBuildOutLoss INTEGER
  acTrunkLineBuildOutOverwrite INTEGER
  acTrunkLineBuildOutXPM0 Unsigned32
  acTrunkLineBuildOutXPM1 Unsigned32
  acTrunkLineBuildOutXPM2 Unsigned32

AcTrunkISDNCommonEntry  
SEQUENCE    
  acTrunkISDNCommonTerminationSide INTEGER
  acTrunkISDNCommonQ931LayerResponseBehavior Integer32
  acTrunkISDNCommonIncomingCallsBehavior Unsigned32
  acTrunkISDNCommonOutgoingCallsBehavior Unsigned32
  acTrunkISDNCommonGeneralCCBehavior Unsigned32
  acTrunkISDNCommonIuaInterfaceId Integer32
  acTrunkISDNCommonDuplicateQ931BuffMode Unsigned32
  acTrunkISDNCommonBRILayer2Mode INTEGER

AcTrunkISDNNfasEntry  
SEQUENCE    
  acTrunkISDNNfasDchConfig INTEGER
  acTrunkISDNNfasInterfaceId Unsigned32
  acTrunkISDNNfasGroupNumber Unsigned32

AcTrunkISDNDpnssEntry  
SEQUENCE    
  acTrunkISDNDpnssBehavior Unsigned32
  acTrunkISDNDpnssNumRealChannels Unsigned32
  acTrunkISDNDpnssNumVirtualChannels Unsigned32

AcTrunkCASEntry  
SEQUENCE    
  acTrunkCASTablesIndex Unsigned32
  acTrunkCASTablePerChannel SnmpAdminString

AcTrunkV5Entry  
SEQUENCE    
  acTrunkV5NumberOfCChannels Unsigned32
  acTrunkV5ProtocolSide INTEGER

AcCASFileEntry  
SEQUENCE    
  acCASFileIndex Unsigned32
  acCASFileName SnmpAdminString

AcSonetSDHEntry  
SEQUENCE    
  acSonetSDHIndex Unsigned32
  acSonetSDHFbrGrpMappingType INTEGER
  acSonetSDHFbrGrpKlmNumberingScheme INTEGER
  acSonetSDHFbrGrpAPSDirectionMode INTEGER
  acSonetSDHFbrGrpAPSRevertMode INTEGER
  acSonetSDHFbrGrpAPSWaitToRestoreTime Unsigned32

AcTrunkStatusEntry  
SEQUENCE    
  acTrunkStatusLedStatusColor INTEGER
  acTrunkStatusLedStatusState INTEGER
  acTrunkStatusChannels OCTET STRING
  acTrunkStatusV5InterfaceNum Integer32
  acTrunkStatusV5LinkID Integer32
  acTrunkStatusDChannel INTEGER
  acTrunkStatusAlarm INTEGER

AcDigitalLegsEntry  
SEQUENCE    
  acDigitalLegsLegIndex Unsigned32
  acDigitalLegsCallIndex Unsigned32
  acDigitalLegsTrunk Unsigned32
  acDigitalLegsBchannel Unsigned32
  acDigitalLegsEchoCanceller INTEGER
  acDigitalLegsDTMFDetection INTEGER
  acDigitalLegsVoiceVolume Unsigned32
  acDigitalLegsHighPassFilter INTEGER
  acDigitalLegsInputGain INTEGER
  acDigitalLegsDSPDevice Unsigned32
  acDigitalLegsLegName SnmpAdminString

AcSDHKLMNumberingSchemeEntry  
SEQUENCE    
  acSDHKLMNumberingSchemeTrunkIndex Unsigned32
  acSDHKLMNumberingSchemeTUG3OrSTS1 Unsigned32
  acSDHKLMNumberingSchemeTUG2OrVTG Unsigned32
  acSDHKLMNumberingSchemeTU12OrVT15 Unsigned32

Defined Values

acPSTN 1.3.6.1.4.1.5003.9.10.9
Tok_String
MODULE-IDENTITY    

acPSTNConfiguration 1.3.6.1.4.1.5003.9.10.9.1
OBJECT IDENTIFIER    

acTrunkConfig 1.3.6.1.4.1.5003.9.10.9.1.1
OBJECT IDENTIFIER    

acTrunk 1.3.6.1.4.1.5003.9.10.9.1.1.1
OBJECT IDENTIFIER    

acTrunkTable 1.3.6.1.4.1.5003.9.10.9.1.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkEntry

acTrunkEntry 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkEntry  

acTrunkIndex 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.1
Trunk ID at board in which the call is taking place. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..83  

acTrunkAdministrativeState 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.2
Trunk Administrative State. Access: Online. AC INI-Param: N/A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER locked(0), unLocked(1)  

acTrunkProtocolType 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.3
Used to set the PSTN protocol to be used for this trunk. Relevant only when TDMBusType=acFRAMERS (2). Either: NONE = 0 E1_EURO_ISDN = 1 T1_CAS = 2 T1_RAW_CAS = 3 T1_TRANSPARENT = 4 E1_TRANSPARENT_31 = 5 E1_TRANSPARENT_30 = 6 E1_MFCR2 = 7 E1_CAS = 8 E1_RAW_CAS = 9 T1_NI2_ISDN = 10 T1_4ESS_ISDN = 11 T1_5ESS_9_ISDN = 12 T1_5ESS_10_ISDN = 13 T1_DMS100_ISDN = 14 J1_TRANSPARENT = 15 T1_NTT_ISDN = 16 E1_AUSTEL_ISDN = 17 E1_HKT_ISDN = 18 E1_KOR_ISDN = 19 T1_HKT_ISDN = 20 E1_QSIG = 21 E1_TNZ_ISDN = 22 T1_QSIG = 23 T1_IUA = 28 E1_IUA = 29 E1_FRENCH_VN6_ISDN = 30 E1_FRENCH_VN3_ISDN = 31 T1_EURO_ISDN = 34 T1_DMS100_MERIDIAN_ISDN = 35 T1_NI1_ISDN = 36 E1_DUA = 37 E1_Q931_PACKETS = 38 T1_Q931_PACKETS = 39 E1_NI2_ISDN = 40 E1-CAS-R15 = 41 V5 = 43 BRI-EURO-ISDN = 50 BRI-NI-2 = 51 BRI-DMS100 = 52 BRI-5ESS = 53 BRI-QSIG = 54 BRI-VNG = 55 BRI-NTT = 56 BRI-IUA = 57. . Access: Online. AC INI-Param: PROTOCOLTYPE
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nONE(0), e1EuroISDN(1), t1Cas(2), t1RawCas(3), t1Transparent(4), e1Transparent31(5), e1Transparent30(6), e1Mfcr2(7), e1CasR2(8), e1RawCAS(9), t1-NI2ISDN(10), t1-4EssISDN(11), t1-5Ess-9-ISDN(12), t1-5Ess-10-ISDN(13), t1-Dms100-ISDN(14), j1-TRANSPARENT(15), t1-NTT-ISDN(16), e1-AUSTEL-ISDN(17), e1-HKT-ISDN(18), e1-KOR-ISDN(19), t1-HKT-ISDN(20), e1-QSIG(21), e1-TNZ-22(22), t1-EXTRA-23(23), t1-IUA(28), e1-IUA(29), e1-EXTRA-30(30), e1-FRENCH-VN3-ISDN(31), t1-EXTRA-32(32), eXTRA-33(33), t1-EURO-ISDN(34), t1-DMS100-MERIDIAN-ISDN(35), t1-NI1-ISDN(36), e1-DUA(37), e1-Q931-PACKETS(38), t1-Q931-PACKETS(39), e1-NI2-ISDN(40), e1-CAS-R15(41), v5(43), bRI-EURO-ISDN(50), bRI-NI-2(51), bRI-DMS100(52), bRI-5ESS(53), bRI-QSIG(54), bRI-VNG(55), bRI-NTT(56), bRI-IUA(57)  

acTrunkClockMaster 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.4
Used to select the trunk clock source. 0 = acCLOCK_MASTER_OFF (clock recovered from the line) 1 = acCLOCK_MASTER_ON (the trunk clock source is provided by the internal/TDM bus clock source depending on the parameter TDM Bus Clock Source). Access: Online. AC INI-Param: CLOCKMASTER
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acCLOCK-MASTER-OFF(0), acCLOCK-MASTER-ON(1)  

acTrunkFramingMethod 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.5
Selects the Framing method to be used for this trunk. Access: Online. AC INI-Param: N/A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER eXTENDED-SUPER-FRAME(0), sUPER-FRAME(1), e1-FRAMING-DDF(2), e1-FRAMING-MFF-CRC4(3), e1-FRAMING-MFF-CRC4-EXT(4), t1-FRAMING-F4(6), t1-FRAMING-F12(7), t1-FRAMING-ESF(8), t1-FRAMING-ESF-CRC6(9), t1-FRAMING-F72(10), t1-FRAMING-ESF-CRC6-JT(11)  

acTrunkLineCode 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.6
Use to select line code. B8ZS or AMI for T1 spans and HDB3 or AMI for E1 spans. 0 = Use B8ZS line code (for T1 trunks only = default) 1 = Use AMI line code (for T1 or E1 trunks) 2 = Use HDB3 line code (for E1 trunks only). Access: Online. AC INI-Param: LINECODE
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acB8ZS(0), acAMI(1), acHDB3(2)  

acTrunkTraceLevel 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.7
Defines the Trace level: acNO_TRACE = 0 acFULL_ISDN_TRACE = 1 acLAYER3_ISDN_TRACE = 2 acONLY_ISDN_Q931_MSGS_TRACE = 3 acLAYER3_ISDN_TRACE_NO_DUPLICATION = 4 acFULL_ISDN_TRACE_WITH_DUPLICATION = 5 acISDN_Q931_RAW_DATA_TRACE = 6 acISDN_Q921_RAW_DATA_TRACE = 7 acISDN_Q931_Q921_RAW_DATA_TRACE = 8 acSS7_MTP2 = 10 acSS7_MTP2_AND_APPLI = 11 acSS7_MTP2_SL_L3_NO_MSU = 12 acSS7_AAL = 15. Access: Online. AC INI-Param: TRACELEVEL
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acNO-TRACE(0), acFULL-ISDN-TRACE(1), acLAYER3-ISDN-TRACE(2), acONLY-ISDN-Q931-MSGS-TRACE(3), acLAYER3-ISDN-TRACE-NO-DUPLICATION(4), acFULL-ISDN-TRACE-WITH-DUPLICATION(5), acISDN-Q931-RAW-DATA-TRACE(6), acISDN-Q921-RAW-DATA-TRACE(7), acISDN-Q931-Q921-RAW-DATA-TRACE(8), acSS7-MTP2(10), acSS7-MTP2-AND-APPLI(11), acSS7-MTP2-SL-L3-NO-MSU(12), acSS7-AAL(15)  

acTrunkDialPlanName 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.8
Sets the Dial Plan name that will be used on the specific trunk. Range = string 11 characters. Access: Instant. AC INI-Param: CasTrunkDialPlanName
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..11)  

acTrunkLineType 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.9
Line type. lineTypeBRI(12) - If the physical type is BRI. lineTypeE1(10)/lineTypeT1(11) - For non BRI IF when there are other lines that are already configured to either E1 or T1. lineTypeUnknown(-1) - For non BRI IF when no lines are configured. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lineTypeE1(10), lineTypeT1(11), lineTypeBRI(12), lineTypeUnknown(21)  

acTrunkAutoClockPriority 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.10
Defines the trunk priority for auto-clock fallback (Priority range: 0 - 100 (0 - 99 are priority settings, in which 0 = highest Priority and is the default setting 100 = Do not choose this trunk). Access: Online. AC INI-Param: AutoClockTrunkPriority
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

acTrunkDeactivate 1.3.6.1.4.1.5003.9.10.9.1.1.1.1.1.11
Deactivating a trunk forces AIS alarm on that trunk. Deactivation is used for trunk maintenance without locking the trunk. Activating the trunk will stop the alarm on the trunk. notAvailable(0) appears when the trunk is locked. The trunk can't be SET to this state. Access: Online. AC INI-Param: N/A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAvailable(0), deActivated(1), activated(2)  

acTrunkLine 1.3.6.1.4.1.5003.9.10.9.1.1.2
OBJECT IDENTIFIER    

acTrunkLineTable 1.3.6.1.4.1.5003.9.10.9.1.1.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkLineEntry

acTrunkLineEntry 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkLineEntry  

acTrunkLineBuildOutLoss 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.1
Used to select the line build out loss to be used for this trunk. 0 = 0 dB 1 = 7.5 dB 2 = 15 dB 3 = 22.5 dB. Access: Online. AC INI-Param: LINEBUILDOUT.LOSS
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ac0DB(0), ac7-5DB(1), ac15DB(2), ac22-5DB(3)  

acTrunkLineBuildOutOverwrite 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.2
Used to overwrite the Framer's XPM registers values (these registers control the line pulse shape). 0 = No overwrite 1 = Overwrite. Access: Online. AC INI-Param: LINEBUILDOUT.OVERWRITE
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acNO-OVER-WRITE(0), acOVER-WRITE(1)  

acTrunkLineBuildOutXPM0 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.3
Used to control the Framer's XPM0 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert users. Range = 0 to 255. Access: Online. AC INI-Param: LINEBUILDOUT.XPM0
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

acTrunkLineBuildOutXPM1 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.4
Used to control the Framer's XPM1 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert users. Range = 0 to 255. Access: Online. AC INI-Param: LINEBUILDOUT.XPM1
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

acTrunkLineBuildOutXPM2 1.3.6.1.4.1.5003.9.10.9.1.1.2.1.1.5
Used to control the Framer's XPM2 register value (line pulse shape control). Applicable only when TrunkConfig.LineBuildOut.Overwrite=1. Should be used only by expert users. Range = 0 to 255. Access: Online. AC INI-Param: LINEBUILDOUT.XPM2
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

acTrunkISDN 1.3.6.1.4.1.5003.9.10.9.1.1.3
OBJECT IDENTIFIER    

acTrunkISDNCommon 1.3.6.1.4.1.5003.9.10.9.1.1.3.1
OBJECT IDENTIFIER    

acTrunkISDNCommonTable 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkISDNCommonEntry

acTrunkISDNCommonEntry 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkISDNCommonEntry  

acTrunkISDNCommonTerminationSide 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.1
Used to set the ISDN Termination to either User or Network. Termination = For ISDN only. User side = 0 Network side = 1. Access: Online. AC INI-Param: TERMINATIONSIDE
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acUSER-TERMINATION-SIDE(0), acNETWORK-TERMINATION-SIDE(1)  

acTrunkISDNCommonQ931LayerResponseBehavior 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.2
Bit-field used to determine several behavior options, which influence how the Q.931 protocol behaves. Access: Online. AC INI-Param: ISDNIBEHAVIOR
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -2147483647..2147483647  

acTrunkISDNCommonIncomingCallsBehavior 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.3
This is the bit-field used to determine several behavior options that influence how the ISDN Stack INCOMING calls behave. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. Access: Online. AC INI-Param: ISDNINCALLSBEHAVIOR
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acTrunkISDNCommonOutgoingCallsBehavior 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.4
This is the bit-field used to determine several behavior options that influence how the ISDN Stack OUTGOING calls behave. Refer to Appendix A.8 in the 'VoPLib Reference Library User's Manual. Access: Online. AC INI-Param: ISDNOUTCALLSBEHAVIOR
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

acTrunkISDNCommonGeneralCCBehavior 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.5
This is the bit-field used to determine several general ISDN behavior options. Refer to the Appendix A.8 'ISDN Flexible Behavior' in the VoPLib Reference Library User's Manual Document #: LTRT-00740. Access: Online. AC INI-Param: ISDNGENERALCCBEHAVIOR
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

acTrunkISDNCommonIuaInterfaceId 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.6
Defines the IUA trunk interface ID value - unsigned integer - in RFC 3057 - SIGTRAN. Default = 0xFFFFFFFF. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..2147483647  

acTrunkISDNCommonDuplicateQ931BuffMode 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.7
Activates / de-activates delivery of raw Q.931 messages. Refer to the VoPLib documentation ('ISDN Flexible Behavior'). Access: Online. AC INI-Param: ISDNDUPLICATEQ931BUFFMODE
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

acTrunkISDNCommonBRILayer2Mode 1.3.6.1.4.1.5003.9.10.9.1.1.3.1.1.1.8
Indicates point to point or point to Multipoint mode for layer2. Applicable in BRI trunks only. One of the following values: Point to point = 0 Point to Multipoint = 1 . Access: Online. AC INI-Param: BriLayer2Mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bRI-L2-MODE-P2P(0), bRI-L2-MODE-P2MP(1)  

acTrunkISDNNfas 1.3.6.1.4.1.5003.9.10.9.1.1.3.2
OBJECT IDENTIFIER    

acTrunkISDNNfasTable 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkISDNNfasEntry

acTrunkISDNNfasEntry 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkISDNNfasEntry  

acTrunkISDNNfasDchConfig 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1.1
Defines D-channel configuration. This setting is only applicable to ISDN PRI protocols that support NFAS and/or D-channel backup procedures. 0 = D-channel is Primary 1 = Backup 2 = NFAS. Access: Online. AC INI-Param: DCHCONFIG
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER acDCH-CONFIG-PRIMARY(0), acDCH-CONFIG-BACKUP(1), acDCH-CONFIG-NFAS(2)  

acTrunkISDNNfasInterfaceId 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1.2
Defines the Interface ID. Works with NS_EXPLICIT_INTERFACE_ID. Refer to the VoPLib documentation(ISDN Flexible Behavior). Default = (unsigned char)-1. Range = 0 to 255. Access: Online. AC INI-Param: ISDNNFASINTERFACEID
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

acTrunkISDNNfasGroupNumber 1.3.6.1.4.1.5003.9.10.9.1.1.3.2.1.1.3
Relevant only for T1 ISDN NFAS trunks indicates the group number of the NFAS group. ;Valid NFAS group numbers are only 1 to 9, 0 indicating that this trunk is not NFAS (in this case the ISDNNFASInterfaceID and DchConfig parameters are ignored). Access: Online. AC INI-Param: NFASGROUPNUMBER
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..9  

acTrunkISDNDpnss 1.3.6.1.4.1.5003.9.10.9.1.1.3.3
OBJECT IDENTIFIER    

acTrunkISDNDpnssTable 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkISDNDpnssEntry

acTrunkISDNDpnssEntry 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkISDNDpnssEntry  

acTrunkISDNDpnssBehavior 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1.1
The DPNSSBehaviour parameter represents a Bit field parameter. Each bit represents a specific type of DPNSS behavior. Currently only the first 2 bits are in use. - DPNSS_BEHAV_STOP_SABMR_AFTER_NL_AND_NT1 bit: (bit #0, bit mask 0x0001) When set to 1: DPNSS stops repeating SABMR after NL and NT1 limits are exceeded. When set to 0: DPNSS continues repeating SABMR after NL and NT1 limits are exceeded. Default is 0 (continue repeating SABMR) - DPNSS_BEHAV_FULL_STARTUP_SUCCESS bit: (bit #1, bit mask 0x0002) When set to 1: the Startup Procedure is considered as a SUCCESS only when ALL DLCs succeeded to Reset When set to 0: the Startup Procedure is considered as a SUCCESS as soon as 1 DLC succeeded to Reset Default is 0: (only partial reset is considered as a success). . Access: Online. AC INI-Param: DPNSSBehavior
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acTrunkISDNDpnssNumRealChannels 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1.2
This parameter is relevant only to protocol ISDN DPNSS. Defines the number of real channels. Default value is 30. Valid range 1 to 30. Access: Online. AC INI-Param: DPNSSNumRealChannels
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..30  

acTrunkISDNDpnssNumVirtualChannels 1.3.6.1.4.1.5003.9.10.9.1.1.3.3.1.1.3
This parameter is relevant only to protocol ISDN DPNSS. Defines the number of virtual channels. Default value is 30. Valid range 0 to 30. Access: Online. AC INI-Param: DPNSSNumVirtualChannels
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..30  

acTrunkCAS 1.3.6.1.4.1.5003.9.10.9.1.1.4
OBJECT IDENTIFIER    

acTrunkCASTable 1.3.6.1.4.1.5003.9.10.9.1.1.4.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkCASEntry

acTrunkCASEntry 1.3.6.1.4.1.5003.9.10.9.1.1.4.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkCASEntry  

acTrunkCASTablesIndex 1.3.6.1.4.1.5003.9.10.9.1.1.4.1.1.1
This parameter determines which CAS protocol file to use on a specific trunk. The index value corresponds to the number configured for the parameter CASFileName_X. Range = not greater than the parameter defining the PSTN CAS Table Num. Access: Online. AC INI-Param: CASTABLEINDEX
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

acTrunkCASTablePerChannel 1.3.6.1.4.1.5003.9.10.9.1.1.4.1.1.2
Sets the Cas protocol table index per channel. User need to set each channel the table number 0-7, with comma saperator between channels: '1,3,1,3,1,3..'. Access: Online. AC INI-Param: CasChannelIndex
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..63)  

acTrunkV5 1.3.6.1.4.1.5003.9.10.9.1.1.5
OBJECT IDENTIFIER    

acTrunkV5Table 1.3.6.1.4.1.5003.9.10.9.1.1.5.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkV5Entry

acTrunkV5Entry 1.3.6.1.4.1.5003.9.10.9.1.1.5.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkV5Entry  

acTrunkV5NumberOfCChannels 1.3.6.1.4.1.5003.9.10.9.1.1.5.1.1.1
Indicates the number of timeslots used as communication channels in a V5 trunk. 0 - No C-channel, the trunk is voice only. 1 - Timeslot 16 is used for the V5 signaling . Access: Online. AC INI-Param: V5NumberOfCChannels
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..1  

acTrunkV5ProtocolSide 1.3.6.1.4.1.5003.9.10.9.1.1.5.1.1.2
Indicates the V5 side of the V5 protocol served by the trunk.. 0 - AN side. 1 - LE side . Access: Online. AC INI-Param: V5ProtocolSide
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER an-Side(0), le-Side(1)  

acTrunkGlobal 1.3.6.1.4.1.5003.9.10.9.1.1.8
OBJECT IDENTIFIER    

acTrunkGlobalLifeLineType 1.3.6.1.4.1.5003.9.10.9.1.1.8.1
This parameter is used to define the type of trunk lifeline. Short trunks 1-2, 3-4. 0 = Activate lifeline on power down 1 = Activate lifeline on power down or on detection of LAN disconnect 2 = Activate lifeline on power down or on detection of LAN disconnect or loss of ping. Access: Offline. AC INI-Param: TrunkLifeLineType
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hW-Only(0), hW-And-Link-Detection(1), hW-And-Link-And-Network-Detection(2)  

acISDNConfig 1.3.6.1.4.1.5003.9.10.9.1.2
OBJECT IDENTIFIER    

acMiscISDN 1.3.6.1.4.1.5003.9.10.9.1.2.1
OBJECT IDENTIFIER    

acMiscISDNQ931RelayMode 1.3.6.1.4.1.5003.9.10.9.1.2.1.1
Activates / de-activates the ISDN level 3 Q.931 Relay Mode. Choose 0 or ActivateLAPDmessaging or Q931_RELAY_TO_HOST or Layer3_IS_IUA. Access: Offline. AC INI-Param: Q931RELAYMODE
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), activateLAPDmessaging(1), layer3-IS-IUA(3)  

acMiscISDNDuplicateQ931BuffMode 1.3.6.1.4.1.5003.9.10.9.1.2.1.2
Access: Offline. AC INI-Param: ISDNDUPLICATEQ931BUFFMODE
Status: obsolete Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

acDS3Config 1.3.6.1.4.1.5003.9.10.9.1.3
OBJECT IDENTIFIER    

acDS3ConfigFramingMethod 1.3.6.1.4.1.5003.9.10.9.1.3.1
Used to select the physical DS3 framing method to be used in this board. 0 = M23 framing 1 = C Bit Parity. Access: Offline. AC INI-Param: DS3FRAMINGMETHOD
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER dS3-M23(0), dS3-C-BIT-PARITY(1)  

acDS3ConfigClockSource 1.3.6.1.4.1.5003.9.10.9.1.3.2
Selects the physical DS3 framing method to be used in this board. Applicable only to the TP-2810. 0 = DS3 Clock is recovered from the line 1 = DS3 trunk clock source is provided by the board's internal clock 2 = Clock is taken from the local PLL which is not synchronized with any other clock. Access: Offline. AC INI-Param: DS3CLOCKSOURCE
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER acClock-Source-External(0), acClock-Source-Local-Board(1), acClock-Source-Local-PLL(2)  

acDS3ConfigLineBuiltOut 1.3.6.1.4.1.5003.9.10.9.1.3.3
Used to select the DS3 line build out. Applies only to the TP-2810. Access: Offline. AC INI-Param: DS3LINEBUILTOUT
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER acLINE-BUILT-OUT-LEVEL-1(0), acLINE-BUILT-OUT-LEVEL-2(1), acLINE-BUILT-OUT-LEVEL-3(2), acLINE-BUILT-OUT-LEVEL-4(3), acLINE-BUILT-OUT-LEVEL-5(4), acLINE-BUILT-OUT-LEVEL-6(5)  

acCasConfig 1.3.6.1.4.1.5003.9.10.9.1.4
OBJECT IDENTIFIER    

acCasConfigEnable 1.3.6.1.4.1.5003.9.10.9.1.4.1
This parameter enables or disables the possibility CAS protocol configuration. At TP6310 When this parameter is enable the conference will disabled in case it's relevant. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: CASProtocolEnable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acCASFile 1.3.6.1.4.1.5003.9.10.9.1.4.2
OBJECT IDENTIFIER    

acCASFileTable 1.3.6.1.4.1.5003.9.10.9.1.4.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcCASFileEntry

acCASFileEntry 1.3.6.1.4.1.5003.9.10.9.1.4.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcCASFileEntry  

acCASFileIndex 1.3.6.1.4.1.5003.9.10.9.1.4.2.1.1.1
Cas Table Indexd. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..7  

acCASFileName 1.3.6.1.4.1.5003.9.10.9.1.4.2.1.1.2
This is a pointer to the CAS filename index (0-7). The index is CASFileName_X. CASFileName_0 through to CASFileName_7 are the path and names of the CAS protocol configuration files. AC INI-Param: CASFILENAME
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

acSonetSDH 1.3.6.1.4.1.5003.9.10.9.1.5
OBJECT IDENTIFIER    

acSonetSDHTable 1.3.6.1.4.1.5003.9.10.9.1.5.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcSonetSDHEntry

acSonetSDHEntry 1.3.6.1.4.1.5003.9.10.9.1.5.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcSonetSDHEntry  

acSonetSDHIndex 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.1
Fiber groupe index. AC INI-Param: N/A
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..1  

acSonetSDHFbrGrpMappingType 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.2
Selects SDH/SONET mapping type (signal label + payload mapping type) for the PSTN interface. Generally per Fiber Group. Single Fiber Group supported in the PSTN interface of TP6310 and TP12610. Applicable only to the TP-6310 and TP-12610. Relevant only when acSysTDMBusType = acFRAMERS (2). 0 = Asynchronous VT1.5 and DS1 1 = Asynchronous TU12 and E1 3 = Asynchronous mapping of DS3 in STS1, DS3 channelized to DS1s 15 = Undefined Should be in coordination with other parameters as follows: - sonetMediumType - acTrunkProtocolType. Access: Offline. AC INI-Param: SDHFbrGrp_Mapping_Type
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER asynchronousVT15andDS1(0), asynchronousTU12andE1(1), sTS1asynchronousDS3(3), undefined(15)  

acSonetSDHFbrGrpKlmNumberingScheme 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.3
Provides VC/VT numbering scheme for STM-1/OC3 fiber group. Access: Offline. AC INI-Param: SDHFbrGrp_KLM_Numbering_Scheme
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER numberingScheme-MLK(0), numberingScheme-LMK(1), numberingScheme-KLM(2)  

acSonetSDHFbrGrpAPSDirectionMode 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.4
Sets the Automatic Protection Switch Unidir/Bidir mode for the Fiber Group. Access: Offline. AC INI-Param: SDHFbrGrp_APS_DirMode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unidirectional(0), bidirectional(1)  

acSonetSDHFbrGrpAPSRevertMode 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.5
Sets the Automatic Protection Switch Revertive mode for the Fiber Group. Access: Offline. AC INI-Param: SDHFbrGrp_APS_RevertMode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER nonRevertive(0), revertive(1)  

acSonetSDHFbrGrpAPSWaitToRestoreTime 1.3.6.1.4.1.5003.9.10.9.1.5.1.1.6
Sets the APS Wait-to-restore time for the Fiber Group. Access: Offline. AC INI-Param: SDHFbrGrp_APS_WTR
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 5..12  

acPSTNStatus 1.3.6.1.4.1.5003.9.10.9.2
OBJECT IDENTIFIER    

acTrunkStatus 1.3.6.1.4.1.5003.9.10.9.2.1
OBJECT IDENTIFIER    

acTrunkStatusTable 1.3.6.1.4.1.5003.9.10.9.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcTrunkStatusEntry

acTrunkStatusEntry 1.3.6.1.4.1.5003.9.10.9.2.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcTrunkStatusEntry  

acTrunkStatusLedStatusColor 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.1
Trunk led status color. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(0), red(1), green(2)  

acTrunkStatusLedStatusState 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.2
Trunk led status blinking rate. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER steady(0), blink(1)  

acTrunkStatusChannels 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.3
Reperesents Trunk's Channels-Status. Each nibble (half Byte) presents one channel status, as following: 1 - invalid B-Channel. 2 - None. 3 - Open. 4 - Media. 5 - SS7. 6 - HDLC. 7 - DPNSS. 8 - CAS. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

acTrunkStatusV5InterfaceNum 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.4
V5.2 interface containing this trunk. -1 means information not available or not relevant. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..31  

acTrunkStatusV5LinkID 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.5
V5.2 link containing this trunk. -1 means information not available or not relevant. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..62  

acTrunkStatusDChannel 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.6
Describes the trunk's D channel status. 0 - dChannelEstablished 1 - dChannelNotEstablished 10 - dChannelNotApplicable. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dChannelEstablished(0), dChannelNotEstablished(1), dChannelNotApplicable(10)  

acTrunkStatusAlarm 1.3.6.1.4.1.5003.9.10.9.2.1.1.1.7
Describes the trunk's alarm status. 1 - Disabled. 2 - Active - OK. 3 - LOS/LOF Alarm. 4 - AIS Alarm. 5 - RAI Alram. 6 - D-Channel Alarm. 7 - Lower Layer Down. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER greyDisabled(0), greenActive(1), redLosLof(2), blueAis(3), yellowRai(4), orangeDChannel(5), purpleLowerLayerDown(6)  

acDigitalLegs 1.3.6.1.4.1.5003.9.10.9.2.2
OBJECT IDENTIFIER    

acDigitalLegsTable 1.3.6.1.4.1.5003.9.10.9.2.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcDigitalLegsEntry

acDigitalLegsEntry 1.3.6.1.4.1.5003.9.10.9.2.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcDigitalLegsEntry  

acDigitalLegsLegIndex 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.1
Decribes The Digital EndPoint In A Call. AC INI-Param: N/A
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..5000  

acDigitalLegsCallIndex 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.2
Decribes The Call which The Digital EndPoint Participant In It. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..5000  

acDigitalLegsTrunk 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.3
Describes the Trunk the Leg belong to. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

acDigitalLegsBchannel 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.4
Describes the Bchannel the Leg belong to. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..76500  

acDigitalLegsEchoCanceller 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.5
Enables or Disables the Echo Canceller. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acDigitalLegsDTMFDetection 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.6
Enables or Disables the DTMF Detection. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acDigitalLegsVoiceVolume 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.7
Describs the volume of the voice in dB. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..20000  

acDigitalLegsHighPassFilter 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.8
Enables or Disables theHigh Pass Filter. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acDigitalLegsInputGain 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.9
Describes the Input Gain on the leg in dB. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acDigitalLegsDSPDevice 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.10
describes the DSP Device the Leg connected to. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..20000  

acDigitalLegsLegName 1.3.6.1.4.1.5003.9.10.9.2.2.1.1.11
Describes the Leg Name as in the Control Protocol. AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

acSDHKLMNumberingScheme 1.3.6.1.4.1.5003.9.10.9.2.3
OBJECT IDENTIFIER    

acSDHKLMNumberingSchemeTable 1.3.6.1.4.1.5003.9.10.9.2.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AcSDHKLMNumberingSchemeEntry

acSDHKLMNumberingSchemeEntry 1.3.6.1.4.1.5003.9.10.9.2.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  AcSDHKLMNumberingSchemeEntry  

acSDHKLMNumberingSchemeTrunkIndex 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.1
Trunk Number. AC INI-Param: N/A
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..5000  

acSDHKLMNumberingSchemeTUG3OrSTS1 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.2
AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..3  

acSDHKLMNumberingSchemeTUG2OrVTG 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.3
AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..7  

acSDHKLMNumberingSchemeTU12OrVT15 1.3.6.1.4.1.5003.9.10.9.2.3.1.1.4
AC INI-Param: N/A
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4  

acFiberGroupStatus 1.3.6.1.4.1.5003.9.10.9.2.4
OBJECT IDENTIFIER    


Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor