A3COM-HUAWEI-SYS-MAN-MIB

File: A3COM-HUAWEI-SYS-MAN-MIB.mib (64638 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
SNMP-TARGET-MIB A3COM-HUAWEI-OID-MIB

Imported symbols

OBJECT-GROUP MODULE-COMPLIANCE NOTIFICATION-GROUP
Integer32 OBJECT-TYPE MODULE-IDENTITY
NOTIFICATION-TYPE TimeTicks Unsigned32
DateAndTime DisplayString RowStatus
SnmpTagList SnmpTagValue h3cCommon

Defined Types

H3cSysCurEntry  
SEQUENCE    
  h3cSysCurEntPhysicalIndex Integer32
  h3cSysCurCFGFileIndex Integer32
  h3cSysCurImageIndex Integer32
  h3cSysCurBtmFileName OCTET STRING
  h3cSysCurUpdateBtmFileName OCTET STRING

H3cSysReloadScheduleEntry  
SEQUENCE    
  h3cSysReloadScheduleIndex Integer32
  h3cSysReloadEntity Integer32
  h3cSysReloadCfgFile Integer32
  h3cSysReloadImage Integer32
  h3cSysReloadReason DisplayString
  h3cSysReloadScheduleTime DateAndTime
  h3cSysReloadRowStatus RowStatus
  h3cSysReloadScheduleTagList SnmpTagList

H3cSysImageEntry  
SEQUENCE    
  h3cSysImageIndex Integer32
  h3cSysImageName DisplayString
  h3cSysImageSize Integer32
  h3cSysImageLocation DisplayString
  h3cSysImageType INTEGER

H3cSysCFGFileEntry  
SEQUENCE    
  h3cSysCFGFileIndex Integer32
  h3cSysCFGFileName DisplayString
  h3cSysCFGFileSize Integer32
  h3cSysCFGFileLocation DisplayString

H3cSysBtmLoadEntry  
SEQUENCE    
  h3cSysBtmLoadIndex Integer32
  h3cSysBtmFileName OCTET STRING
  h3cSysBtmFileType INTEGER
  h3cSysBtmRowStatus RowStatus
  h3cSysBtmErrorStatus INTEGER
  h3cSysBtmLoadTime TimeTicks

H3cSysPackageEntry  
SEQUENCE    
  h3cSysPackageIndex Integer32
  h3cSysPackageName DisplayString
  h3cSysPackageSize Unsigned32
  h3cSysPackageLocation DisplayString
  h3cSysPackageType INTEGER
  h3cSysPackageAttribute INTEGER
  h3cSysPackageStatus INTEGER
  h3cSysPackageDescription DisplayString
  h3cSysPackageFeature DisplayString
  h3cSysPackageVersion DisplayString

H3cSysPackageOperateEntry  
SEQUENCE    
  h3cSysPackageOperateIndex Integer32
  h3cSysPackageOperatePackIndex Integer32
  h3cSysPackageOperateStatus INTEGER
  h3cSysPackageOperateRowStatus RowStatus
  h3cSysPackageOperateResult INTEGER

H3cSysIpeFileEntry  
SEQUENCE    
  h3cSysIpeFileIndex Integer32
  h3cSysIpeFileName DisplayString
  h3cSysIpeFileSize Unsigned32
  h3cSysIpeFileLocation DisplayString

H3cSysIpePackageEntry  
SEQUENCE    
  h3cSysIpePackageIndex Integer32
  h3cSysIpePackageName DisplayString
  h3cSysIpePackageSize Unsigned32
  h3cSysIpePackageType INTEGER
  h3cSysIpePackageDescription DisplayString
  h3cSysIpePackageFeature DisplayString
  h3cSysIpePackageVersion DisplayString

H3cSysIpeFileOperateEntry  
SEQUENCE    
  h3cSysIpeFileOperateIndex Integer32
  h3cSysIpeFileOperateFileIndex Integer32
  h3cSysIpeFileOperateAttribute INTEGER
  h3cSysIpeFileOperateRowStatus RowStatus
  h3cSysIpeFileOperateResult INTEGER

Defined Values

h3cSystemMan 1.3.6.1.4.1.43.45.1.10.2.3
This MIB contains objects to manage the system. It focuses on the display of current configure file and image file,and the definition of reloading image. Add the support for XRN.
MODULE-IDENTITY    

h3cSystemManMIBObjects 1.3.6.1.4.1.43.45.1.10.2.3.1
OBJECT IDENTIFIER    

h3cSysClock 1.3.6.1.4.1.43.45.1.10.2.3.1.1
OBJECT IDENTIFIER    

h3cSysLocalClock 1.3.6.1.4.1.43.45.1.10.2.3.1.1.1
This node gives the current local time of the system. The unit of it is DateAndTime.
OBJECT-TYPE    
  DateAndTime  

h3cSysSummerTime 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2
OBJECT IDENTIFIER    

h3cSysSummerTimeEnable 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2.1
This node indicates the status of summer time. If the value of this node is enable, means that summer time is enabled. If the value is disable, means that summer time is disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

h3cSysSummerTimeZone 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2.2
This node describes the name of time zone in summer. The string is only used to display in local time when summer time is running. That the value of h3cSysLocalClock has the time zone information means that summer time is running.
OBJECT-TYPE    
  DisplayString  

h3cSysSummerTimeMethod 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2.3
This node provides the execute method of summer time. oneOff(1): means that summer time only takes effect at specified time. repeating(2): means that summer time takes effect in specified month/day once a year.
OBJECT-TYPE    
  INTEGER oneOff(1), repeating(2)  

h3cSysSummerTimeStart 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2.4
This node provides the start time of summer time.
OBJECT-TYPE    
  DateAndTime Size(8)  

h3cSysSummerTimeEnd 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2.5
This node provides the end time of summer time. The end time must be more than start time one day and less than start time one year.
OBJECT-TYPE    
  DateAndTime Size(8)  

h3cSysSummerTimeOffset 1.3.6.1.4.1.43.45.1.10.2.3.1.1.2.6
This node provides the offset time of summer time. The offset time(in seconds) means that how much time need to be appended to the local time.
OBJECT-TYPE    
  Integer32 0..86399  

h3cSysLocalClockString 1.3.6.1.4.1.43.45.1.10.2.3.1.1.3
This node gives the current local time of the system. For example, Tuesday May 26, 2002 at 1:30:15 would be displayed as: 2002-5-26T13:30:15.0Z
OBJECT-TYPE    
  OCTET STRING Size(16..24)  

h3cSysCurrent 1.3.6.1.4.1.43.45.1.10.2.3.1.2
OBJECT IDENTIFIER    

h3cSysCurTable 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1
The current status of system. A configuration file, an image file and bootrom information are used to describe the current status.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysCurEntry

h3cSysCurEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1.1
An entry of h3cSysCurTable.
OBJECT-TYPE    
  H3cSysCurEntry  

h3cSysCurEntPhysicalIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1.1.1
The value of this object is the entity index which depends on the implementation of ENTITY-MIB. If ENTITY-MIB is not supported, the value for this object is the unit ID for XRN devices , 0 for non-XRN device which has only one mainboard, the board number for non-XRN device which have several mainboards.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysCurCFGFileIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1.1.2
The startup configuration file currently used by the specified entity. If the value of it is zero, no configuration file is used. It will be the value of corresponding h3cSysCFGFileIndex in h3cSysCFGFileTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysCurImageIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1.1.3
The image file currently used by the specified entity. It will be the value of corresponding h3cSysImageIndex in h3cSysImageTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysCurBtmFileName 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1.1.4
The bootrom file currently used by the specified entity.
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

h3cSysCurUpdateBtmFileName 1.3.6.1.4.1.43.45.1.10.2.3.1.2.1.1.5
The default value of this object is the same as the value of h3cSysCurBtmFileName. The value will be changed after updating the bootrom successfully. This bootrom will take effect on next startup.
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

h3cSysReload 1.3.6.1.4.1.43.45.1.10.2.3.1.3
OBJECT IDENTIFIER    

h3cSysReloadSchedule 1.3.6.1.4.1.43.45.1.10.2.3.1.3.1
The object points one row in h3cSysReloadScheduleTable. Its value is equal to the value of h3cSysReloadScheduleIndex. When a reload action is finished, the value of it would be zero which means no any reload schedule is selected.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysReloadAction 1.3.6.1.4.1.43.45.1.10.2.3.1.3.2
Writing reloadOnSchedule(2) to this object performs the reload operation on schedule. If h3cSysReloadScheduleTime is not set, the value of h3cSysReloadAction can't be set to 'reloadOnSchedule(2)'. Writing reloadAtOnce(3)to this object performs the reload operation at once, regardless of the h3cSysReloadScheduleTime. When reloadCancel(4)is set, the scheduled reload action will be cancelled and the value of h3cSysReloadAction will be 'reloadUnavailable(1)',the value of h3cSysReloadSchedule will be 0, h3cSysReloadTag will be given a value of zero length, but the content of h3cSysReloadScheduleTable will remain. The h3cSysReloadSchedule and h3cSysReloadTag determine the reload entity(ies) in mutually exclusive way. And the h3cSysReloadSchedule will be handled at first. If the value of h3cSysReloadSchedule is invalid, then the h3cSysReloadTag will be handled. If the value of h3cSysReloadSchedule is valid, the value of h3cSysReloadTag is ignored and a reload action will be implemented to the entity specified by h3cSysReloadEntity in the entry pointed by h3cSysReloadSchedule. If h3cSysReloadSchedule is valid, but the entry h3cSysReloadSchedule pointing to is not active, the reload action will be ignored , and an inconsistent value will be returned. If multiple entities are required to be reloaded at the same time, the value of h3cSysReloadTag must be specified to select the reload parameters in the h3cSysReloadSceduelTable, and h3cSysReloadSchedule must have the value of '0'. If the whole fabric is to be reloaded in an XRN device, all the units in the fabric must have at least one entry in the h3cSysReloadSceduelTable with the same tag in h3cSysReloadSceduelTagList. When a reload action is done, or there is no reload action, the value should be reloadUnavailable(1).
OBJECT-TYPE    
  INTEGER reloadUnavailable(1), reloadOnSchedule(2), reloadAtOnce(3), reloadCancel(4)  

h3cSysReloadScheduleTable 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3
A reload parameters set table. The table is exclusively used for reloading. When reloading action finished, the value of the table may be empty or still exist. If the mainboard in non-XRN device or all the units of the fabric in XRN device are reloaded,then the table will be refreshed.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysReloadScheduleEntry

h3cSysReloadScheduleEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1
Entry of h3cSysReloadScheduleTable.
OBJECT-TYPE    
  H3cSysReloadScheduleEntry  

h3cSysReloadScheduleIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.1
The index of h3cSysReloadScheduleTable. There are two parts for this index depicted as follows: 31 15 0 +++++++++++++++++++++++++++++++++++++++++ + physical index + random index + ( bit 16..31 ) ( bit 0..15 ) +++++++++++++++++++++++++++++++++++++++++ From bit0 to bit15 (two bytes), if the row is automatic created, the value is zero, and if the row is created by users, then the value is determined by the users. From bit16 to bit31 (two bytes) is the physical index the same as the entPhysicalIndex specified in ENTITY-MIB. For XRN devices, physical index is the value of a chassis entPhysicalIndex. 0 for non-XRN device which has only one main board, the board number for non-XRN device which have multiple main boards.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysReloadEntity 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.2
The value of h3cSysReloadEntity indicates an entry in entPhysicalTable, which is the physical entity to be reloaded. If ENTITY-MIB is not supported,the value for this object is the unit ID for XRN devices , 0 for non-XRN device which has only one mainboard, the board number for non-XRN device which have several mainboards. Each entity has only one row in h3cSysReloadScheduleTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysReloadCfgFile 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.3
The value indicates an entry in h3cSysCFGFileTable. It defines a configuration file for reload action. It is the value of corresponding h3cSysCFGFileIndex in h3cSysCFGFileTable. The zero value means no configuration file has been set for this entry, and no configuration file is used during system reloading.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysReloadImage 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.4
The value indicates an entry in h3cSysImageTable. It defines an image file for reload action. It is the value of corresponding h3cSysImageIndex in h3cSysImageTable. If dual image is supported, the main image attribute can be set through this object or by h3cSysImageType of h3cSysImageTable of the entity. It is strongly suggested to set this attribute by the latter. If main image attribute is set here, the h3cSysImageType in h3cSysImageTable of the corresponding entity will be updated, and vice versa. Before reboot, the device will check the validation of the entry. If the file does not exist, the device will not reboot and a trap will be send to NMS.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysReloadReason 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.5
The reason of system's reloading. It is a zero length octet string when not set.
OBJECT-TYPE    
  DisplayString Size(0..255)  

h3cSysReloadScheduleTime 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.6
Specify the local time at which the reload action will occur. we will only take octet strings with length 8 for this object which indicates the local time of the switch. The maximum scheduled interval between the specified time and the current system clock time is 24 days . field octets contents range ----- ------ -------- ----- 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 For example, Tuesday May 26, 1992 at 1:30:15 PM would be displayed as: 1992-5-26,13:30:15 If the set value is less than the value of h3cSysLocalClock or beyond the maximum scheduled time limit, a bad value error occurred. The value of all-zero octet strings indicates system reload at once if the reload action is reloadOnSchedule(2).
OBJECT-TYPE    
  DateAndTime Size(8)  

h3cSysReloadRowStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.7
If one of the value of h3cSysReloadEntity,h3cSysReloadImage is invalid, the value of h3cSysReloadRowStatus can not be set to the value of ACTIVE. A valid entry means the specified element is available in current system.
OBJECT-TYPE    
  RowStatus  

h3cSysReloadScheduleTagList 1.3.6.1.4.1.43.45.1.10.2.3.1.3.3.1.8
It specifies a tag list for the entry.
OBJECT-TYPE    
  SnmpTagList  

h3cSysReloadTag 1.3.6.1.4.1.43.45.1.10.2.3.1.3.4
This object contains a single tag value which is used to select entries in the h3cSysReloadScheduleTable. In the h3cSysReloadScheduleTable,any entry that contains a tag value which is equal to the value of this object is selected. For example, the value of h3cSysReloadTag is 'TOM',and the h3cSysReloadScheduleTagList of each h3cSysReloadScheduleTable entry are as follows: 1)'TOM,ROBERT,MARY' 2)'TOM,DAVE' 3)'DAVE,MARY' Since there are 'TOM' in 1) and 2),so 1) and 2) are selected. If this object contains a value of zero length, no entries are selected.
OBJECT-TYPE    
  SnmpTagValue  

h3cSysImage 1.3.6.1.4.1.43.45.1.10.2.3.1.4
OBJECT IDENTIFIER    

h3cSysImageNum 1.3.6.1.4.1.43.45.1.10.2.3.1.4.1
The number of system images. It indicates the total entries of h3cSysImageTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysImageTable 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2
The system image management table. When 'copy srcfile destfile' is executed via the CLI, if destfile is not existed, then h3cSysImageType of the new file will be 'none'; otherwise h3cSysImageType keeps its current value. When 'move srcfile destfile' is executed via the CLI, h3cSysImageType and h3cSysImageIndex remain the same while h3cSysImageLocation changes. When 'rename srcfile' is executed via the CLI,h3cSysImageType and h3cSysImageIndex remain the same while h3cSysImageName changes. When 'delete srcfile' is executed via the CLI, the file is deleted from h3cSysImageTable while index of the file keeps and will not be allocated.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysImageEntry

h3cSysImageEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2.1
An entity image entry. Each entry consists of information of an entity image. The h3cSysImageIndex exclusively defines an image file.
OBJECT-TYPE    
  H3cSysImageEntry  

h3cSysImageIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2.1.1
There are two parts for the index depicted as follows: 31 15 0 +++++++++++++++++++++++++++++++++++ + physical index + image index + +++++++++++++++++++++++++++++++++++ From bit0 to bit15 (two bytes) is the image index;Image file Index is a monotonically increasing integer for the sole purpose of indexing events. When it reaches the maximum value, an extremely unlikely event, the agent wraps the value back to 1 and may flush existing entries. From bit16 to bit31 (two bytes) is the physical index the same as the entPhysicalIndex specified in ENTITY-MIB. If ENTITY-MIB is not supported,the value for this object is the unit ID for XRN devices ,0 for non-XRN device which has only one main board,the board number for non-XRN device which have several main boards. Any index beyond the above range will not be supported. If a file is added in, its h3cSysImageIndex will be the maximum image index plus one. If the image file is removed, renamed, or moved from one place to another, its h3cSysImageIndex is not reallocated. If the image file's content is replaced, its h3cSysImageIndex will not change.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysImageName 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2.1.2
The file name of the image. It MUST NOT contain the path of the file.
OBJECT-TYPE    
  DisplayString  

h3cSysImageSize 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2.1.3
Size of the file in bytes.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysImageLocation 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2.1.4
The directory path of the image. Its form should be the same as what defined in file system. Currently it is defined as follows: For mainboard: flash:/ For slave mainboard and subboards: slotN#flash:/ For XRN devices: unitN>slotN#flash:/
OBJECT-TYPE    
  DisplayString  

h3cSysImageType 1.3.6.1.4.1.43.45.1.10.2.3.1.4.2.1.5
It indicates the reloading sequence attribute of the image. For devices which support dual image: If the value is 'main(1)',the image will be the first image in the next reloading procedure. If the value is 'backup(2)', the image will be used if the main image fails. If the value is 'secure(4)', the image will be used if the main image and backup image both fail. If the value is 'none(3)',the image will not be used in the next reloading procedure. At the same time,you also can specify the main image by h3cSysReloadImage in h3cSysReloadScheduleTable. If the image is different from previous main image, the previous main image will not be main image again. And the image table will update with this variation. Vice versa, if you have defined the reload schedule, and then you define a new main image through h3cSysImageType when you are waiting the reload schedule to be executed, the real main image will be the latest one. It is strongly suggested to define the main image here, not by h3cSysReloadImage in h3cSysReloadScheduleTable. There are some rules for setting the value of h3cSysImageType: a)When a new image file is defined as 'main' or 'backup' file,the h3cSysImageType of old 'main' or 'backup' file will automatically be 'none'. b)It is forbidden to set 'none' attribute manually. c)It is forbidden to set 'secure' attribute manually. d)If 'main' image is set to 'backup', the file keeps 'main'. And vice versa. At this time, the file has 'main-backup' property. e)If the secure image is set to 'main' or 'backup', the file has 'main-secure' or 'backup-secure'property. f)If the secure image is set to 'main' and 'backup', the file has the 'main-backup-secure' property. g)If the none image is set to 'main' or 'backup', the file has the 'main' or 'backup' property. The following table describes whether it is ok to set to another state directly from original state. +--------------+-----------+-------------+-------------+ | set to | set to | set to | set to | | | | | | original | 'main' | 'backup' | 'none' | 'secure' | state | | | | | --------------+--------------+-----------+-------------+-------------+ | | | | | main | --- | yes | no | no | | | | | | | | | | | --------------+--------------+-----------+-------------|-------------+ | | | | | backup | yes | --- | no | no | | | | | | --------------+--------------+-----------+-------------|-------------+ | | | | | | | | | | none | yes | yes | --- | no | | | | | | --------------+--------------+-----------+-------------+-------------+ | | | | | secure | yes | yes | no | --- | | | | | | | | | | | --------------+--------------+-----------+-------------+-------------+ If there is one main image in the system, one row of H3cSysReloadScheduleEntry whose h3cSysReloadImage is equal to the main image's h3cSysImageIndex will be created automatically. But if any row is deleted, it will not be created automatically in h3cSysReloadScheduleTable. For the device which doesn't support dual image(main/backup): Only 'main' and 'none' is supported and it only can be set from none to main. When a new image file is defined as 'main' file,the h3cSysImageType of old 'main' file will automatically be 'none'.
OBJECT-TYPE    
  INTEGER main(1), backup(2), none(3), secure(4), main-backup(5), main-secure(6), backup-secure(7), main-backup-secure(8)  

h3cSysCFGFile 1.3.6.1.4.1.43.45.1.10.2.3.1.5
OBJECT IDENTIFIER    

h3cSysCFGFileNum 1.3.6.1.4.1.43.45.1.10.2.3.1.5.1
The number of the configuration files in the system. It indicates the total entries of h3cSysCFGFileTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysCFGFileTable 1.3.6.1.4.1.43.45.1.10.2.3.1.5.2
A table of configuration files in this system. At present, the system doesn't support dual configure file, it should act as 'dual image' if dual configure file is supported.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysCFGFileEntry

h3cSysCFGFileEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.5.2.1
A configuration file entry. Each entry consists of information of a configuration file. h3cSysCFGFileIndex exclusively decides a configuration file.
OBJECT-TYPE    
  H3cSysCFGFileEntry  

h3cSysCFGFileIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.5.2.1.1
There are two parts for the index depicted as follows: 31 15 0 +++++++++++++++++++++++++++++++++++ + physical index + cfgFile index + +++++++++++++++++++++++++++++++++++ From bit0 to bit15 (two bytes) is the configuration file index; the configuration file index is a monotonically increasing integer for the sole purpose of indexing events. When it reaches the maximum value, an extremely unlikely event, the agent wraps the value back to 1 and may flush existing entries. From bit16 to bit31 (two bytes) is the physical index the same as the entPhysicalIndex specified in ENTITY-MIB. If ENTITY-MIB is not supported, the value for this object is the unit ID for XRN devices ,0 for non-XRN device which has only one slot,the board number for non-XRN device which have several slots. Any index beyond the above range will not be supported.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysCFGFileName 1.3.6.1.4.1.43.45.1.10.2.3.1.5.2.1.2
Configuration file name. The name should not include the colon (:) character as it is a special separator character used to delineate the device name, partition name and the file name.
OBJECT-TYPE    
  DisplayString  

h3cSysCFGFileSize 1.3.6.1.4.1.43.45.1.10.2.3.1.5.2.1.3
Size of the file in bytes. Note that it does not include the size of the filesystem file header. File size will always be non-zero.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysCFGFileLocation 1.3.6.1.4.1.43.45.1.10.2.3.1.5.2.1.4
The directory path of the image. Its form should be the same as what defined in filesystem. Currently it is defined as follows: For mainboard: flash:/ For slave mainboard and subboards: slotN#flash:/ For XRN devices: unitN>slotN#flash:/
OBJECT-TYPE    
  DisplayString  

h3cSysBtmFile 1.3.6.1.4.1.43.45.1.10.2.3.1.6
OBJECT IDENTIFIER    

h3cSysBtmFileLoad 1.3.6.1.4.1.43.45.1.10.2.3.1.6.1
OBJECT IDENTIFIER    

h3cSysBtmLoadMaxNumber 1.3.6.1.4.1.43.45.1.10.2.3.1.6.1.1
This object shows the maximum number of h3cSysBtmLoadEntry in each device/unit.
OBJECT-TYPE    
  Integer32  

h3cSysBtmLoadTable 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2
This table is used to update the bootrom and show the results of the update operation. The bootrom files are listed at the h3cFlhFileTable. These files are used to update bootrom.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysBtmLoadEntry

h3cSysBtmLoadEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1
Entries in the h3cSysBtmLoadTable are created and deleted using the h3cSysBtmRowStatus object. When a new row is being created and the number of entries is h3cSysBtmLoadMaxNumber, the row with minimal value of h3cSysBtmLoadTime and the value of h3cSysBtmFileType is none(2), should be destroyed automatically.
OBJECT-TYPE    
  H3cSysBtmLoadEntry  

h3cSysBtmLoadIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1.1
The index of h3cSysBtmLoadTable. There are two parts for this index depicted as follows: 31 15 0 +++++++++++++++++++++++++++++++++++++++++ + physical index + random index + ( bit 16..31 ) ( bit 0..15 ) +++++++++++++++++++++++++++++++++++++++++ From bit0 to bit15 (two bytes), if the row is created by command line, the value is determined by system, and if the row is created by SNMP, the value is determined by users. From bit16 to bit31 (two bytes) is the physical index the same as the entPhysicalIndex specified in ENTITY-MIB. If ENTITY-MIB is not supported, the value of this object is the unit ID for XRN devices, 0 for non-XRN device which has only one main board, the board number for non-XRN device which has multiple main boards.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysBtmFileName 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1.2
The bootrom file name is determined by the users. The file must exist in corresponding entity. The validity of the bootrom file will be identified by system. If the file is invalid, the bootrom should fail to be updated, and the value of h3cSysBtmErrorStatus should be failed(4).
OBJECT-TYPE    
  OCTET STRING Size(1..64)  

h3cSysBtmFileType 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1.3
main(1) - The effective bootrom file. none(2) - The noneffective file. When bootrom is being updated, this object must be set to main(1). When bootrom is updated successfully, this object should be main(1), and the former object with the same physical index should be none(2). When bootrom failed to be updated, this object should be none(2).
OBJECT-TYPE    
  INTEGER main(1), none(2)  

h3cSysBtmRowStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1.4
Only support active(1), createAndGo(4), destroy(6). When a row is created successfully, the value of this object should be active(1), the value of h3cSysBtmFileName and h3cSysBtmFileType can not be modified by users. When bootrom is being updated, the value of h3cSysBtmErrorStatus is inProgress(2). When bootrom failed to be updated, the value of h3cSysBtmErrorStatus should be failed(4). When bootrom is updated successfully, the value of h3cSysBtmErrorStatus should be success(3). The value of h3cSysCurUpdateBtmFileName should change to the new bootrom file name. When another row is created successfully with the same physical index, and the update is successful, then the value of former h3cSysBtmFileType should be none(2) automatically. If a row is destroyed, h3cSysCurUpdateBtmFileName should not change. If a device/unit reboots, h3cSysBtmLoadTable should be empty.
OBJECT-TYPE    
  RowStatus  

h3cSysBtmErrorStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1.5
This object shows the status of the specified operation after creating a row. invalidFile(1) - file is invalid. inProgress(2) - the operation is in progress. success(3) - the operation was done successfully. failed(4) - the operation failed.
OBJECT-TYPE    
  INTEGER invalidFile(1), inProgress(2), success(3), failed(4)  

h3cSysBtmLoadTime 1.3.6.1.4.1.43.45.1.10.2.3.1.6.2.1.6
This object indicates operation time.
OBJECT-TYPE    
  TimeTicks  

h3cSysPackage 1.3.6.1.4.1.43.45.1.10.2.3.1.7
OBJECT IDENTIFIER    

h3cSysPackageNum 1.3.6.1.4.1.43.45.1.10.2.3.1.7.1
The number of software packages. It indicates the total entries of h3cSysPackageTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysPackageTable 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2
The system package management table.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysPackageEntry

h3cSysPackageEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1
An software package entry. Each entry consists of information of an software package.
OBJECT-TYPE    
  H3cSysPackageEntry  

h3cSysPackageIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.1
There are two parts for the index depicted as follows: 31 15 0 +++++++++++++++++++++++++++++++++++ + physical index + package index + +++++++++++++++++++++++++++++++++++ From bit0 to bit15 (two bytes) is the Package index; Package file Index is a monotonically increasing integer for the sole purpose of indexing events. When it reaches the maximum value, an extremely unlikely event, the agent wraps the value back to 1 and may flush existing entries. From bit16 to bit31 (two bytes) is the physical index the same as the entPhysicalIndex specified in ENTITY-MIB. Any index beyond the above range will not be supported. If a file is added in, its h3cSysPackageIndex will be the maximum image index plus one. If the package file is removed, renamed, or moved from one place to another, its h3cSysPackageIndex is not reallocated. If the package file's content is replaced, its h3cSysPackageIndex will not change.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysPackageName 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.2
The file name of the package. It MUST NOT contain the path of the file.
OBJECT-TYPE    
  DisplayString  

h3cSysPackageSize 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.3
Size of the file in bytes.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

h3cSysPackageLocation 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.4
The directory path of the package. Its form should be the same as what defined in file system. Currently it is defined as follows: For mainboard: flash:/ For slave mainboard and subboards: slotN#flash:/
OBJECT-TYPE    
  DisplayString  

h3cSysPackageType 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.5
It indicates the type of the package file. boot : kernel, file system, memory management and other core components. system : interface management, configuration management and other basic system package. feature : feature packages, providing different services. patch : patch file contains fixes for a specific defect.
OBJECT-TYPE    
  INTEGER boot(1), system(2), feature(3), patch(4)  

h3cSysPackageAttribute 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.6
It indicates the attribute of the package file. If the value is 'primary', the package will be the first package in the next reloading procedure. If the value is 'secondary', the package will be used if the primary package fails. If the value is 'none', it will not be used in the next reloading procedure.
OBJECT-TYPE    
  INTEGER none(1), primary(2), secondary(3), primarySecondary(4)  

h3cSysPackageStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.7
It indicates the status of the package file. If this file is used in the current system, its status is 'active'.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

h3cSysPackageDescription 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.8
It is the description of the package.
OBJECT-TYPE    
  DisplayString  

h3cSysPackageFeature 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.9
Indicate the feature of the package. Different package files could be the same feature.
OBJECT-TYPE    
  DisplayString  

h3cSysPackageVersion 1.3.6.1.4.1.43.45.1.10.2.3.1.7.2.1.10
Indicate the version of the package.
OBJECT-TYPE    
  DisplayString  

h3cSysPackageOperateEntryLimit 1.3.6.1.4.1.43.45.1.10.2.3.1.7.3
The maximum number of the entries in h3cSysPackageOperateTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysPackageOperateTable 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4
A table of package file operate.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysPackageOperateEntry

h3cSysPackageOperateEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4.1
An operate request entry.
OBJECT-TYPE    
  H3cSysPackageOperateEntry  

h3cSysPackageOperateIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4.1.1
The unique index value of a row in this table.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysPackageOperatePackIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4.1.2
Specify the package file in the h3cSysPackageTable.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysPackageOperateStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4.1.3
activate or deactivate a package in the h3cSysPackageTable.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

h3cSysPackageOperateRowStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4.1.4
the status of this table entry. When the status is active all the object's value in the entry is not allowed to modified.
OBJECT-TYPE    
  RowStatus  

h3cSysPackageOperateResult 1.3.6.1.4.1.43.45.1.10.2.3.1.7.4.1.5
the result of the operation.
OBJECT-TYPE    
  INTEGER opInProgress(1), opSuccess(2), opUnknownFailure(3), opInvalidFile(4), opNotSupport(5)  

h3cSysIpeFile 1.3.6.1.4.1.43.45.1.10.2.3.1.8
OBJECT IDENTIFIER    

h3cSysIpeFileNum 1.3.6.1.4.1.43.45.1.10.2.3.1.8.1
The number of software IPE(Image Package Envelop) files. It indicates the total entries of h3cSysIpeFileTable.
OBJECT-TYPE    
  Integer32 0..2147483647  

h3cSysIpeFileTable 1.3.6.1.4.1.43.45.1.10.2.3.1.8.2
The system IPE file manage table.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysIpeFileEntry

h3cSysIpeFileEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.8.2.1
An IPE package file entry. Each entry consists of information of an IPE package file. h3cSysIpeFileIndex exclusively decides an IPE file.
OBJECT-TYPE    
  H3cSysIpeFileEntry  

h3cSysIpeFileIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.8.2.1.1
There are two parts for the index depicted as follows: 31 15 0 +++++++++++++++++++++++++++++++++++ + physical index + IPE index + +++++++++++++++++++++++++++++++++++ From bit0 to bit15 (two bytes) is the IPE file index; IPE file Index is a monotonically increasing integer for the sole purpose of indexing events. When it reaches the maximum value, an extremely unlikely event, the agent wraps the value back to 1 and may flush existing entries. From bit16 to bit31 (two bytes) is the physical index the same as the entPhysicalIndex specified in ENTITY-MIB. Any index beyond the above range will not be supported. If a file is added in, its h3cSysIpeFileIndex will be the maximum image ndex plus one. If the IPE file is removed, renamed, or moved from one place to another, its h3cSysIpeFileIndex is not reallocated. If the IPE file's content is replaced, its h3cSysIpeFileIndex will not change.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysIpeFileName 1.3.6.1.4.1.43.45.1.10.2.3.1.8.2.1.2
The file name of the IPE file. It MUST NOT contain the path of the file.
OBJECT-TYPE    
  DisplayString  

h3cSysIpeFileSize 1.3.6.1.4.1.43.45.1.10.2.3.1.8.2.1.3
Size of the file in bytes.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

h3cSysIpeFileLocation 1.3.6.1.4.1.43.45.1.10.2.3.1.8.2.1.4
The directory path of the IPE file. Its form should be the same as what defined in file system. Currently it is defined as follows: For mainboard: flash:/ For slave mainboard and subboards: slotN#flash:/
OBJECT-TYPE    
  DisplayString  

h3cSysIpePackageTable 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3
The IPE package file table. It shows the package files in the IPE file.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysIpePackageEntry

h3cSysIpePackageEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1
An entry of the h3cIpePackageTable. Indexed by h3cSysIpeFileIndex and h3cSysIpePackageIndex.
OBJECT-TYPE    
  H3cSysIpePackageEntry  

h3cSysIpePackageIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.1
It is the IPE package index; IPE Package Index is a monotonically increasing integer for the sole purpose of indexing events. When it reaches the maximum value, an extremely unlikely event, the agent wraps the value back to 1 and may flush existing entries. Any index beyond the above range will not be supported.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysIpePackageName 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.2
The file name of the package file.
OBJECT-TYPE    
  DisplayString  

h3cSysIpePackageSize 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.3
Size of the package file in bytes.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

h3cSysIpePackageType 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.4
It indicates the type of the package file. boot : kernel, file system, memory management and other core components. system : interface management, configuration management and other basic system package. feature : feature packages, providing different services. patch : patch file contains fixes for a specific defect.
OBJECT-TYPE    
  INTEGER boot(1), system(2), feature(3), patch(4)  

h3cSysIpePackageDescription 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.5
It is the description of the package.
OBJECT-TYPE    
  DisplayString  

h3cSysIpePackageFeature 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.6
Indicate the feature of the package.
OBJECT-TYPE    
  DisplayString  

h3cSysIpePackageVersion 1.3.6.1.4.1.43.45.1.10.2.3.1.8.3.1.7
The version of the package.
OBJECT-TYPE    
  DisplayString  

h3cSysIpeFileOperateTable 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4
A table of IPE file operate.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cSysIpeFileOperateEntry

h3cSysIpeFileOperateEntry 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4.1
An operate request entry.
OBJECT-TYPE    
  H3cSysIpeFileOperateEntry  

h3cSysIpeFileOperateIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4.1.1
The unique index value of a row in this table.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysIpeFileOperateFileIndex 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4.1.2
Specify the IPE file in the h3cSysIpeFileTable. This IPE file will be unpacked to package files.
OBJECT-TYPE    
  Integer32 1..2147483647  

h3cSysIpeFileOperateAttribute 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4.1.3
It indicates the attribute of the IPE file when it is used in the reloading. If the value is 'primary', the packages in the IPE file will be the first packages in the next reloading procedure. If the value is 'secondary', the package in the IPE file will be used if the primary packages fails. If the value is 'none', the IPE file is only unpacked, will not be used in the reloading procedure.
OBJECT-TYPE    
  INTEGER none(1), primary(2), secondary(3), primarySecondary(4)  

h3cSysIpeFileOperateRowStatus 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4.1.4
the status of this table entry. When the status is active all the object's value in the entry is not allowed to modified.
OBJECT-TYPE    
  RowStatus  

h3cSysIpeFileOperateResult 1.3.6.1.4.1.43.45.1.10.2.3.1.8.4.1.5
the result of the operation.
OBJECT-TYPE    
  INTEGER opInProgress(1), opSuccess(2), opUnknownFailure(3), opInvalidFile(4), opDeviceFull(5), opFileOpenError(6)  

h3cSystemManMIBNotifications 1.3.6.1.4.1.43.45.1.10.2.3.2
OBJECT IDENTIFIER    

h3cSysClockChangedNotification 1.3.6.1.4.1.43.45.1.10.2.3.2.1
A clock changed notification is generated when the current local date and time for the system has been manually changed. The value of h3cSysLocalClock reflects new date and time.
NOTIFICATION-TYPE    

h3cSysReloadNotification 1.3.6.1.4.1.43.45.1.10.2.3.2.2
A h3cSysReloadNotification will be sent before the corresponding entity is rebooted. It will also be sent if the entity fails to reboot because the clock has changed.
NOTIFICATION-TYPE    

h3cSysStartUpNotification 1.3.6.1.4.1.43.45.1.10.2.3.2.3
a h3cSysStartUpNotification trap will be sent when the system starts up with 'main' image file failed, a trap will be sent to indicate which type the current image file (I.e backup or secure)is.
NOTIFICATION-TYPE    

h3cSystemManMIBConformance 1.3.6.1.4.1.43.45.1.10.2.3.3
OBJECT IDENTIFIER    

h3cSystemManMIBCompliances 1.3.6.1.4.1.43.45.1.10.2.3.3.1
OBJECT IDENTIFIER    

h3cSystemManMIBCompliance 1.3.6.1.4.1.43.45.1.10.2.3.3.1.1
The compliance statement for entities which implement the system management MIB.
MODULE-COMPLIANCE    

h3cSystemManMIBGroups 1.3.6.1.4.1.43.45.1.10.2.3.3.2
OBJECT IDENTIFIER    

h3cSysClockGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.1
A collection of objects providing mandatory system clock information.
OBJECT-GROUP    

h3cSysReloadGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.2
A collection of objects providing mandatory system reload.
OBJECT-GROUP    

h3cSysImageGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.3
A collection of objects providing mandatory system image information.
OBJECT-GROUP    

h3cSysCFGFileGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.4
A collection of objects providing mandatory system configuration file information.
OBJECT-GROUP    

h3cSysCurGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.5
A collection of system current status.
OBJECT-GROUP    

h3cSystemManNotificationGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.6
A collection of notifications.
NOTIFICATION-GROUP    

h3cSystemBtmLoadGroup 1.3.6.1.4.1.43.45.1.10.2.3.3.2.7
A collection of objects providing system update bootrom information.
OBJECT-GROUP