A3COM-HUAWEI-NQA-MIB

File: A3COM-HUAWEI-NQA-MIB.mib (95961 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC INET-ADDRESS-MIB
A3COM-HUAWEI-OID-MIB DISMAN-PING-MIB SNMP-FRAMEWORK-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
OBJECT-IDENTITY NOTIFICATION-TYPE Integer32
Counter32 Gauge32 DateAndTime
DisplayString RowStatus InetAddressType
InetAddress huaweiDatacomm pingCtlEntry
pingCtlOwnerIndex pingCtlTestName pingCtlType
pingCtlTargetAddress pingCtlTargetAddressType pingCtlDescr
SnmpAdminString

Defined Types

HwNqaCtlEntry  
SEQUENCE    
  hwNqaCtlTargetPort Integer32
  hwNqaCtlSourcePort Integer32
  hwNqaCtlTTL Integer32
  hwNqaCtlJitterAdminInterval Integer32
  hwNqaCtlJitterAdminNumPackets Integer32
  hwNqaCtlHttpOperationType INTEGER
  hwNqaCtlHttpOperationString DisplayString
  hwNqaCtlFtpOperationType INTEGER
  hwNqaCtlFtpUsername DisplayString
  hwNqaCtlFtpPassword DisplayString
  hwNqaCtlFtpOperationString DisplayString
  hwNqaCtlVPNInstance DisplayString
  hwNqaCtlHistoryKeptTime Integer32
  hwNqaCtlHistoryEnable INTEGER
  hwNqaCtlICPIFAdvFactor Integer32
  hwNqaCtlCodecType INTEGER

HwNqaResultsEntry  
SEQUENCE    
  hwNqaResultsRttNumDisconnects Unsigned32
  hwNqaResultsRttTimeouts Unsigned32
  hwNqaResultsRttBusies Unsigned32
  hwNqaResultsRttNoConnections Unsigned32
  hwNqaResultsRttDrops Unsigned32
  hwNqaResultsRttSequenceErrors Unsigned32
  hwNqaResultsRttStatsErrors Unsigned32
  hwNqaResultsMaxDelaySD Unsigned32
  hwNqaResultsMaxDelayDS Unsigned32
  hwNqaResultsLostPacketRatio Unsigned32
  hwNqaResultsPacketLateArrival Unsigned32
  hwNqaResultsRttSum Unsigned32
  hwNqaResultsNumOfDelaySD Unsigned32
  hwNqaResultsMinDelaySD Unsigned32
  hwNqaResultsSumDelaySD Unsigned32
  hwNqaResultsSum2DelaySD Unsigned32
  hwNqaResultsNumOfDelayDS Unsigned32
  hwNqaResultsMinDelayDS Unsigned32
  hwNqaResultsSumDelayDS Unsigned32
  hwNqaResultsSum2DelayDS Unsigned32

HwNqaJitterStatsEntry  
SEQUENCE    
  hwNqaJitterStatsNumOfRTT Counter32
  hwNqaJitterStatsMinOfPositivesSD Gauge32
  hwNqaJitterStatsMaxOfPositivesSD Gauge32
  hwNqaJitterStatsNumOfPositivesSD Gauge32
  hwNqaJitterStatsSumOfPositivesSD Gauge32
  hwNqaJitterStatsSum2PositivesSD Gauge32
  hwNqaJitterStatsMinOfNegativesSD Gauge32
  hwNqaJitterStatsMaxOfNegativesSD Gauge32
  hwNqaJitterStatsNumOfNegativesSD Gauge32
  hwNqaJitterStatsSumOfNegativesSD Gauge32
  hwNqaJitterStatsSum2NegativesSD Gauge32
  hwNqaJitterStatsMinOfPositivesDS Gauge32
  hwNqaJitterStatsMaxOfPositivesDS Gauge32
  hwNqaJitterStatsNumOfPositivesDS Gauge32
  hwNqaJitterStatsSumOfPositivesDS Gauge32
  hwNqaJitterStatsSum2PositivesDS Gauge32
  hwNqaJitterStatsMinOfNegativesDS Gauge32
  hwNqaJitterStatsMaxOfNegativesDS Gauge32
  hwNqaJitterStatsNumOfNegativesDS Gauge32
  hwNqaJitterStatsSumOfNegativesDS Gauge32
  hwNqaJitterStatsSum2NegativesDS Gauge32
  hwNqaJitterStatsPacketLossSD Gauge32
  hwNqaJitterStatsPacketLossDS Gauge32
  hwNqaJitterStatsAvePositivesSD Gauge32
  hwNqaJitterStatsAveNegativesSD Gauge32
  hwNqaJitterStatsAvePositivesDS Gauge32
  hwNqaJitterStatsAveNegativesDS Gauge32
  hwNqaJitterStatsPktLossUnknown Gauge32
  hwNqaJitterStatsOperOfICPIF Gauge32
  hwNqaJitterStatsOperOfMOS Gauge32

HwNqaTcpServerEntry  
SEQUENCE    
  hwNqaTcpServerIpAddress InetAddress
  hwNqaTcpServerPort Integer32
  hwNqaTcpServerRowStatus RowStatus

HwNqaUdpServerEntry  
SEQUENCE    
  hwNqaUdpServerIpAddress InetAddress
  hwNqaUdpServerPort Integer32
  hwNqaUdpServerRowStatus RowStatus

HwNqaStatisticsCtlEntry  
SEQUENCE    
  hwNqaCtlStatisticsInterval Unsigned32
  hwNqaCtlStatisticsGroupNumber Unsigned32
  hwNqaCtlStatisticsKeptTime Unsigned32
  hwNqaCtlBeginTime DateAndTime
  hwNqaCtlLifeTime Unsigned32

HwNqaStatisticsResultsEntry  
SEQUENCE    
  hwNqaStatResIndex Unsigned32
  hwNqaStatResIpTargetAddressType InetAddressType
  hwNqaStatResIpTargetAddress InetAddress
  hwNqaStatResMinRtt Gauge32
  hwNqaStatResMaxRtt Gauge32
  hwNqaStatResAverageRtt Gauge32
  hwNqaStatResProbeResponses Counter32
  hwNqaStatResSentProbes Counter32
  hwNqaStatResRttSumOfSquares Counter32
  hwNqaStatResStartTime DateAndTime
  hwNqaStatResInterval Gauge32
  hwNqaStatResRttNumDisconnects Counter32
  hwNqaStatResRttTimeouts Counter32
  hwNqaStatResRttBusies Counter32
  hwNqaStatResRttNoConnections Counter32
  hwNqaStatResRttDrops Counter32
  hwNqaStatResRttSequenceErrors Counter32
  hwNqaStatResRttErrors Counter32
  hwNqaStatResLostPacketRatio Gauge32
  hwNqaStatResPacketLateArrival Counter32
  hwNqaStatResRttSum Counter32
  hwNqaStatResNumOfDelaySD Counter32
  hwNqaStatResMinDelaySD Gauge32
  hwNqaStatResMaxDelaySD Gauge32
  hwNqaStatResSumDelaySD Counter32
  hwNqaStatResSum2DelaySD Counter32
  hwNqaStatResNumOfDelayDS Counter32
  hwNqaStatResMinDelayDS Gauge32
  hwNqaStatResMaxDelayDS Gauge32
  hwNqaStatResSumDelayDS Counter32
  hwNqaStatResSum2DelayDS Counter32

HwNqaGroupStatsJitterEntry  
SEQUENCE    
  hwNqaStatJitterIndex Unsigned32
  hwNqaStatJitterMinOfPosSD Gauge32
  hwNqaStatJitterMaxOfPosSD Gauge32
  hwNqaStatJitterNumOfPosSD Counter32
  hwNqaStatJitterSumOfPosSD Counter32
  hwNqaStatJitterSumOfSquarePosSD Counter32
  hwNqaStatJitterMinOfNegSD Gauge32
  hwNqaStatJitterMaxOfNegSD Gauge32
  hwNqaStatJitterNumOfNegSD Counter32
  hwNqaStatJitterSumOfNegSD Counter32
  hwNqaStatJitterSumOfSquareNegSD Counter32
  hwNqaStatJitterMinOfPosDS Gauge32
  hwNqaStatJitterMaxOfPosDS Gauge32
  hwNqaStatJitterNumOfPosDS Counter32
  hwNqaStatJitterSumOfPosDS Counter32
  hwNqaStatJitterSumOfSquarePosDS Counter32
  hwNqaStatJitterMinOfNegDS Gauge32
  hwNqaStatJitterMaxOfNegDS Gauge32
  hwNqaStatJitterNumOfNegDS Counter32
  hwNqaStatJitterSumOfNegDS Counter32
  hwNqaStatJitterSumOfSquareNegDS Counter32
  hwNqaStatJitterPacketLossSD Counter32
  hwNqaStatJitterPacketLossDS Counter32
  hwNqaStatJitterAvePosSD Gauge32
  hwNqaStatJitterAveNegSD Gauge32
  hwNqaStatJitterAvePosDS Gauge32
  hwNqaStatJitterAveNegDS Gauge32
  hwNqaStatJitterPktLossUnknown Counter32
  hwNqaStatJitterMaxOfICPIF Gauge32
  hwNqaStatJitterMinOfICPIF Gauge32
  hwNqaStatJitterMaxOfMOS Gauge32
  hwNqaStatJitterMinOfMOS Gauge32

HwNqaReactionEntry  
SEQUENCE    
  hwNqaReactOwnerIndex SnmpAdminString
  hwNqaReactTestName SnmpAdminString
  hwNqaReactItemIndex Unsigned32
  hwNqaReactCheckedElement INTEGER
  hwNqaReactThresholdUpperLimit Unsigned32
  hwNqaReactThresholdLowerLimit Unsigned32
  hwNqaReactThresholdType INTEGER
  hwNqaReactThresholdConsecNum Unsigned32
  hwNqaReactThresholdAccumNum Unsigned32
  hwNqaReactActionType INTEGER
  hwNqaReactCurrentStatus INTEGER
  hwNqaReactRowStatus RowStatus
  hwNqaReactCheckedNum Unsigned32
  hwNqaReactThresholdNum Unsigned32

HwNqaStatisticsReactionEntry  
SEQUENCE    
  hwNqaStatReactOwnerIndex SnmpAdminString
  hwNqaStatReactTestName SnmpAdminString
  hwNqaStatReactIndex Unsigned32
  hwNqaStatReactItemIndex Unsigned32
  hwNqaStatReactCheckedNum Counter32
  hwNqaStatReactThresholdNum Counter32

Defined Values

hwNqa 1.3.6.1.4.1.43.45.1.5.25.28
The private mib file includes the test information of the device. It is supplementary for rfc2925.txt.
MODULE-IDENTITY    

hwNqaObjects 1.3.6.1.4.1.43.45.1.5.25.28.1
OBJECT IDENTIFIER    

hwNqaImplementationTypeDomains 1.3.6.1.4.1.43.45.1.5.25.28.2
OBJECT IDENTIFIER    

hwNqaUdpEcho 1.3.6.1.4.1.43.45.1.5.25.28.2.1
Indicates that an implementation is using the UDP based echo server. Notes: The hwNqaCtlTargetPort and hwNqaCtlSourcePort need to be set, while in the pingUdpEcho Node, hwNqaCtlTargetPort must be set to the default value.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqaTcpconnect 1.3.6.1.4.1.43.45.1.5.25.28.2.2
Indicates that an implementation is attempting to connect to a TCP port in order to calculate a round trip time. Notes: The hwNqaCtlTargetPort and hwNqaCtlSourcePort need to be set, while in the pingTcpConnectionAttempt Node, hwNqaCtlTargetPort must be set to the default value.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqajitter 1.3.6.1.4.1.43.45.1.5.25.28.2.3
Indicates that an implementation is using udp for packet transfers. 'jitter' will cause the NQA(Network Quality Analysis) application to perform delay variance analysis.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqaHttp 1.3.6.1.4.1.43.45.1.5.25.28.2.4
Indicates that an implementation is using udp for name resolution, tcp connect and tcp data transfer mechanisms for HTTP data download from a particular HTTP Server. It causes the NQA application to perform a download of the object specified in the URL.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqadlsw 1.3.6.1.4.1.43.45.1.5.25.28.2.5
Indicates that an implementation is using tcp for sending keepalives. 'dlsw' will cause the NQA application to perform a keepalive operation to measure the response time of a DLSw peer.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqadhcp 1.3.6.1.4.1.43.45.1.5.25.28.2.6
Indicates that an implementation is using udp for sending dhcp requests. 'dhcp' will cause the NQA application to perform an IP Address lease request/teardown operation.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqaftp 1.3.6.1.4.1.43.45.1.5.25.28.2.7
Indicates that an implementation is using tcp packet for ftp connect and data transfer.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

hwNqaMIBVersion 1.3.6.1.4.1.43.45.1.5.25.28.1.1
Version string of this MIB. The format will be: 'Version.Release.Patch: Description' An instance likes: '1.0.0: Initial NQA MIB'
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hwNqaCtlTable 1.3.6.1.4.1.43.45.1.5.25.28.1.2
Defines the NQA Control Extend Table for providing, via SNMP, the capability of performing network analysis operations at a remote host.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaCtlEntry

hwNqaCtlEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1
Defines an entry in the hwNqaCtlTable. The operation of this table is same as that of pingResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaCtlEntry  

hwNqaCtlTargetPort 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.1
The destination port that may be used by udpEcho, tcpConnect and jitter probes.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65536  

hwNqaCtlSourcePort 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.2
The source port that may be used by all tests except for dns and dlsw. If no source port is specified, system will create a random port as source port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65536  

hwNqaCtlTTL 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.3
Specifies the value to store in the TTL Field in the IP packet used to encapsulate the NQA probe.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwNqaCtlJitterAdminInterval 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.4
Time value in milliseconds that is an interval between two continuous probes in jitter test. This object is only used by jitter test.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..60000  

hwNqaCtlJitterAdminNumPackets 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.5
Packet number that specifys how many packets will be sent in one jitter test. This object is only used by jitter test.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwNqaCtlHttpOperationType 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.6
Http operation type: get or post.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER get(1), post(2)  

hwNqaCtlHttpOperationString 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.7
Http operation string. For example, if the http operation type is get, the string will be url, home page and http version.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..255)  

hwNqaCtlFtpOperationType 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.8
Ftp operation type.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER get(1), put(2)  

hwNqaCtlFtpUsername 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.9
Ftp username.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

hwNqaCtlFtpPassword 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.10
Ftp password.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

hwNqaCtlFtpOperationString 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.11
Ftp operation string. If the ftp operation type is get, the string must be the file name which will be gotten from ftp server.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..255)  

hwNqaCtlVPNInstance 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.12
VPN name by which system finds route in the specified VPN to send NQA probe packets.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..255)  

hwNqaCtlHistoryKeptTime 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.13
To indicate how long the history records will be saved in the pingProbeHistoryTable table after the test stopped.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1440  

hwNqaCtlHistoryEnable 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.14
To indicate whether the history should be recorded in the PingProbeHistoryTable or not. enabled(1) --history will be recorded disabled(2) --history will not be recorded.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwNqaCtlICPIFAdvFactor 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.15
The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. Suggestion values: |-----------------------------------|-------| | Service |factor | |-----------------------------------|-------| |conventional wire-line | 0 | |-----------------------------------|-------| |mobility within Building | 5 | |-----------------------------------|-------| |mobility within geographical area | 10 | |-----------------------------------|-------| |access to hard-to-reach location | 20 | |-----------------------------------|-------|
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

hwNqaCtlCodecType 1.3.6.1.4.1.43.45.1.5.25.28.1.2.1.16
To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notDefined(1), g711Alaw(2), g711Ulaw(3), g729A(4), icmpTimestamp(5)  

hwNqaResultsTable 1.3.6.1.4.1.43.45.1.5.25.28.1.3
Defines the NQA Results Extend Table for providing the capability of performing NQA operations at a remote host. The results of these operations are stored in the hwNqaResultsTable. The operation of this table is same as that of pingResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaResultsEntry

hwNqaResultsEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1
The operation of this table is same as that of pingResultsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaResultsEntry  

hwNqaResultsRttNumDisconnects 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.1
The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttTimeouts 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.2
The number of times that a NQA probe failed because the probe timed out.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttBusies 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.3
The number of times that a NQA probe failed because all NQA tasks have been running. If a new probe fails to start, the value of this object is incremented. The next test will not start until the next Frequency.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttNoConnections 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.4
The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttDrops 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.5
The number of times that a NQA operation failed to initiated for unavailibility of necessary internal resources.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttSequenceErrors 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.6
The number of packets arrived out of sequence.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttStatsErrors 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.7
The number of some other errors.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsMaxDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.8
The maximal delay from source device to destination device. Currently this value is only used for jitter test, and this value must be 0 in other type test. In jitter test, if destination system time is not valid, the SD delay may be set 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsMaxDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.9
The maximal delay from destination device to source device. Currently this value is only used for jitter test, and this value is 0 in other type test. In jitter test, if destination system time is not valid, the DS delay may be set 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsLostPacketRatio 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.10
The value of this object reflects the drop rate of NQA test. For example, this value is 30 that means source device only had received 70% packets of total sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsPacketLateArrival 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.11
The value of this object indicates the number of the packets that arrived after the timeout.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsRttSum 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.12
The sum of round trip time.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsNumOfDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.13
The number of delay from source to destination that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsMinDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.14
The minimum of all one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsSumDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.15
The sum of one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsSum2DelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.16
The sum of squares of one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsNumOfDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.17
The number of delay from destination to source that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsMinDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.18
The minimum of all one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsSumDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.19
The sum of one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaResultsSum2DelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.3.1.20
The sum of squares of one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaJitterStatsTable 1.3.6.1.4.1.43.45.1.5.25.28.1.4
Statistics table for latest jitter activity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaJitterStatsEntry

hwNqaJitterStatsEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1
An entry contains the statistics for the latest jitter activity. This entry is created only if the pingCtlType is hwNqajitter.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaJitterStatsEntry  

hwNqaJitterStatsNumOfRTT 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.1
The number of received destination device responses with which jitter test can reach round-trip time.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaJitterStatsMinOfPositivesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.2
The value of time that records the minimal positive jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMaxOfPositivesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.3
The value of time that records the maximal positive jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsNumOfPositivesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.4
The number that records positive jitter times from source to destination in the jitter test. The total number of the value of all positive jitters in packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSumOfPositivesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.5
The value of time that records the sum of positive jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSum2PositivesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.6
The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMinOfNegativesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.7
The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMaxOfNegativesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.8
The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsNumOfNegativesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.9
The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values in packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSumOfNegativesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.10
The value of time that records the sum of negative jitter values from source to destination in the jitter test. The total number of the value of all negative jitters in packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSum2NegativesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.11
The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMinOfPositivesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.12
The value of time that records the minimal positive jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMaxOfPositivesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.13
The value of time that records the maximal positive jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsNumOfPositivesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.14
The number that records positive jitter times from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSumOfPositivesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.15
The value of time that records the sum of positive jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSum2PositivesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.16
The value of time that records the sum of square of positive jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMinOfNegativesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.17
The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsMaxOfNegativesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.18
The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsNumOfNegativesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.19
The number that records negative jitter times from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSumOfNegativesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.20
The value of time that records the sum of negative jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsSum2NegativesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.21
The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsPacketLossSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.22
The lost packets number sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsPacketLossDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.23
The lost packets number sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsAvePositivesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.24
The value of time that records the average positive jitter value from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsAveNegativesSD 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.25
The value of time that records the average negative jitter value from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsAvePositivesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.26
The value of time that records the average positive jitter value from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsAveNegativesDS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.27
The value of time that records the average negative jitter value from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsPktLossUnknown 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.28
The number of packets which is lost with unknown reason.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsOperOfICPIF 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.29
The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaJitterStatsOperOfMOS 1.3.6.1.4.1.43.45.1.5.25.28.1.4.1.30
The MOS (Mean Opinion Score) value for the latest jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaAgentEnable 1.3.6.1.4.1.43.45.1.5.25.28.1.5
Enable NQA agent function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwNqaTcpServerTable 1.3.6.1.4.1.43.45.1.5.25.28.1.6
A table which contains the status of NQA tcp server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaTcpServerEntry

hwNqaTcpServerEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.6.1
A table which contains the status of NQA tcp server configuration information. This entry includes not only the tcp server ip address but also the tcp server port.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaTcpServerEntry  

hwNqaTcpServerIpAddress 1.3.6.1.4.1.43.45.1.5.25.28.1.6.1.1
Tcp server's ip address.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

hwNqaTcpServerPort 1.3.6.1.4.1.43.45.1.5.25.28.1.6.1.2
Tcp server's port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65536  

hwNqaTcpServerRowStatus 1.3.6.1.4.1.43.45.1.5.25.28.1.6.1.3
hwNqaTcpServerIpAddress and hwNqaTcpServerPort must be set during a creation operation.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwNqaUdpServerTable 1.3.6.1.4.1.43.45.1.5.25.28.1.7
Status of NQA udp server configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaUdpServerEntry

hwNqaUdpServerEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.7.1
This entry includes not only the udp server ip address but also the udp server udp port.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaUdpServerEntry  

hwNqaUdpServerIpAddress 1.3.6.1.4.1.43.45.1.5.25.28.1.7.1.1
Udp server's ip address.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

hwNqaUdpServerPort 1.3.6.1.4.1.43.45.1.5.25.28.1.7.1.2
Udp server's port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65536  

hwNqaUdpServerRowStatus 1.3.6.1.4.1.43.45.1.5.25.28.1.7.1.3
hwNqaUdpServerIpAddress and hwNqaUdpServerPort must be set during a creation operation.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwNqaServerEnable 1.3.6.1.4.1.43.45.1.5.25.28.1.8
Enable NQA server function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwNqaStatsMaxGroupNumber 1.3.6.1.4.1.43.45.1.5.25.28.1.9
The maximum number saved per group. The maximum value of hwNqaCtlStatisticsGroupNumber can not exceed the value of this object.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwNqaStatisticsCtlTable 1.3.6.1.4.1.43.45.1.5.25.28.1.10
Defines the NQA statistics control table for providing, via SNMP, the capability of performing NQA operations at a remote host. The results of these operations are stored in the hwNqaStatisticsResultsTable and the hwNqaGroupStatsJitterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaStatisticsCtlEntry

hwNqaStatisticsCtlEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.10.1
Defines an entry in the hwNqaStatisticsCtlTable. The hwNqaStatisticsCtlTable has the same index as the pingCtlTable in order for a hwNqaStatisticsCtlTable to correspond to the pingCtlEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaStatisticsCtlEntry  

hwNqaCtlStatisticsInterval 1.3.6.1.4.1.43.45.1.5.25.28.1.10.1.1
Statistic information will be calculated after the time that is the value of hwNqaCtlStatisticsInterval.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaCtlStatisticsGroupNumber 1.3.6.1.4.1.43.45.1.5.25.28.1.10.1.2
The value of this object indicates the number of group saved. The length of this object is from 1 to hwNqaStatsMaxGroupNumber.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaCtlStatisticsKeptTime 1.3.6.1.4.1.43.45.1.5.25.28.1.10.1.3
To indicate how long the statistic information will be saved after the test stops.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..1440  

hwNqaCtlBeginTime 1.3.6.1.4.1.43.45.1.5.25.28.1.10.1.4
Time at which the type-specified test will start.
Status: current Access: read-create
OBJECT-TYPE    
  DateAndTime  

hwNqaCtlLifeTime 1.3.6.1.4.1.43.45.1.5.25.28.1.10.1.5
To indicate how long the type-specified test will last.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaStatisticsResultsTable 1.3.6.1.4.1.43.45.1.5.25.28.1.11
Defines the NQA statistics results table for providing the capability of performing NQA operations at a remote host. The statistics results of these operations in a statistic cycle are stored in the hwNqaStatisticsResultsTable. The statistic cycle is the value of hwNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that the probe statistics result (HwNqaStatisticsResultsEntry) belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaStatisticsResultsEntry

hwNqaStatisticsResultsEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1
Defines an entry in the hwNqaStatisticsResultsTable. The hwNqaStatisticsResultsTable has the same index as the pingCtlTable in order for a hwNqaStatisticsResultsEntry to correspond to the pingCtlEntry that caused it to be created.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaStatisticsResultsEntry  

hwNqaStatResIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.1
An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hwNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..ffffffff  

hwNqaStatResIpTargetAddressType 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.2
This object indicates the type of address stored in the corresponding hwNqaStatResIpTargetAddress object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

hwNqaStatResIpTargetAddress 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.3
This object represent the host address to be used at a remote host for performing a network analysis operation.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

hwNqaStatResMinRtt 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.4
The minimum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResMaxRtt 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.5
The maximum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResAverageRtt 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.6
The average NQA probe round-trip-time (RTT).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResProbeResponses 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.7
The number of responses received. The value of this object MUST be reported as 0 when no probe responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResSentProbes 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.8
The value of this object reflects the number of probes sent. The value of this object MUST be reported as 0 when no probes have been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttSumOfSquares 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.9
This object contains the sum of the squares for all NQA responses received. The value of this object MUST be reported as 0 when no NQA responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResStartTime 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.10
This object contains the start time of the statistic.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

hwNqaStatResInterval 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.11
This object contains the interval between two times of statistic.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResRttNumDisconnects 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.12
The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttTimeouts 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.13
The number of times that a probe failed because the probe timed out.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttBusies 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.14
The number of times that a NQA probe failed because errors related to sockets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttNoConnections 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.15
The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttDrops 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.16
The number of times that a NQA operation failed to initiate for unavailibility of necessary internal resources.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttSequenceErrors 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.17
The number of packets arrived out of sequence.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttErrors 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.18
The number of other errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResLostPacketRatio 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.19
The value of this object reflects the drop rate of NQA test packet. For example, if the value is 30, that means source device only had received 70 percent packets of total sent packets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResPacketLateArrival 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.20
The value of this object reflects the number of the packets that arrived after the timeout.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResRttSum 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.21
This object contains the sum of the squares for all NQA responses received during the test lifetime. The value of this object MUST be reported as 0 when no NQA responses have been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResNumOfDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.22
The number of one way times from source to destination that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResMinDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.23
The minimum one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResMaxDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.24
The maximum one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResSumDelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.25
The sum of one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResSum2DelaySD 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.26
The sum of squares of one way times from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResNumOfDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.27
The number of one way times from destination to source that are successfully measured.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResMinDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.28
The minimum one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResMaxDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.29
The maximum one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatResSumDelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.30
The sum of one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatResSum2DelayDS 1.3.6.1.4.1.43.45.1.5.25.28.1.11.1.31
The sum of squares of one way times from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaGroupStatsJitterTable 1.3.6.1.4.1.43.45.1.5.25.28.1.12
Test Group Statistic table for jitter activity in a statistic cycle. The statistic cycle is the value of hwNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that a probe statistics result (HwNqaStatisticsResultsEntry) belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaGroupStatsJitterEntry

hwNqaGroupStatsJitterEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1
An entry contains the group statistic information for jitter activity. This entry is created only if the pingCtlType is hwNqajitter.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaGroupStatsJitterEntry  

hwNqaStatJitterIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.1
An entry in this table is created when the statistic result of a NQA probe in a statistic cycle is determined. An implementation MUST start assigning hwNqaStatJitterIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..ffffffff  

hwNqaStatJitterMinOfPosSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.2
The value of time that records the minimal positive jitter value from source to destination in jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMaxOfPosSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.3
The value of time that records the maximal positive jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterNumOfPosSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.4
The number that records positive jitter times from source to destination in the jitter test. The total number of all positive jitter values in packets sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfPosSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.5
The value of time that records the sum of positive jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfSquarePosSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.6
The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterMinOfNegSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.7
The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMaxOfNegSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.8
The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterNumOfNegSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.9
The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfNegSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.10
The value of time that records the sum of negative jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfSquareNegSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.11
The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterMinOfPosDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.12
The value of time that records the minimal positive jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMaxOfPosDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.13
The value of time that records the maximal positive jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterNumOfPosDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.14
The number that records positive jitter times from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfPosDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.15
The value of time that records the sum of positive jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfSquarePosDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.16
The value of time that records the sum of square of positive jitter values destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterMinOfNegDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.17
The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMaxOfNegDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.18
The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterNumOfNegDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.19
The number that records negative jitter times from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfNegDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.20
The value of time that records the sum of negative jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterSumOfSquareNegDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.21
The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterPacketLossSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.22
The lost packets number sent from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterPacketLossDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.23
The lost packets number sent from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterAvePosSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.24
The value of time that records the average positive jitter value from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterAveNegSD 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.25
The value of time that records the average negative jitter value from source to destination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterAvePosDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.26
The value of time that records the average positive jitter value from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterAveNegDS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.27
The value of time that records the average negative jitter value from destination to source.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterPktLossUnknown 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.28
The number of packets which is lost with unknown reason.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatJitterMaxOfICPIF 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.29
The maximum of all ICPIF values in a statistic cycle for jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMinOfICPIF 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.30
The minimum of all ICPIF values in a statistic cycle for jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMaxOfMOS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.31
The maximum of all MOS values in a statistic cycle for jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaStatJitterMinOfMOS 1.3.6.1.4.1.43.45.1.5.25.28.1.12.1.32
The minimum of all MOS values in a statistic cycle for jitter test.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hwNqaReactionTable 1.3.6.1.4.1.43.45.1.5.25.28.1.13
A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaReactionEntry

hwNqaReactionEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1
Defines an entry in the hwNqaReactionTable.The first two index elements identify the pingCtlEntry that a hwNqaReactItemIndex belongs to. The third index element selects a single reaction.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaReactionEntry  

hwNqaReactOwnerIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.1
The first index of hwNqaReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable. hwNqaReactOwnerIndex and hwNqaReactTestName identify an existed test.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

hwNqaReactTestName 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.2
The second index of hwNqaReactionTable, it is the same as pingCtlTestName in pingCtlTable. hwNqaReactOwnerIndex and hwNqaReactTestName identify an existed test.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

hwNqaReactItemIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.3
The third index of hwNqaReactionTable, it definitely identifies one of the reaction configurations for a test.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32 1..10  

hwNqaReactCheckedElement 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.4
A list of reaction condition type. 'probetime' and 'probefailure' are valid when pingCtlType of the test is not hwNqajitter. 'jitterOwdSD': one way time from source to destination in jitter test. 'jitterOwdDS': one way time from destination to source in jitter test. 'jitterrtt', 'jitterpacketloss', 'jittersd', 'jitterds', 'jitterOwdSD' and 'jitterOwdDS' are valid when pingCtlType of the test is hwNqajitter. 'icpif' and 'mos' are valid when pingCtlType of the test is hwNqajitter and hwNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER probetime(1), probefailure(2), jitterrtt(3), jitterpacketloss(4), jittersd(5), jitterds(6), icpif(7), mos(8), jitterOwdSD(9), jitterOwdDS(10)  

hwNqaReactThresholdUpperLimit 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.5
This object defines an administrative upper-threshold value for hwNqaReactCheckedElement. The value of this object is zero if hwNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaReactThresholdLowerLimit 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.6
This object defines an administrative lower-threshold value for hwNqaReactCheckedElement. The value of hwNqaReactThresholdLowerLimit should be equal or less than the value of hwNqaReactThresholdUpperLimit. The value of this object is zero if hwNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaReactThresholdType 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.7
This object defines the reaction threshold types. invalid(0): Invalid value. average(1): If reaction threshold type is average and the average value of watched operation exceeds threshold limit, an action specified in hwNqaReactActionType is generated when hwNqaReactCurrentStatus changes. consecutive(2): If reaction threshold type is consecutive and the times of watched operation consecutively exceeds the limit specified by hwNqaReactThresholdConsecNum, an action specified in hwNqaReactActionType is generated when hwNqaReactCurrentStatus changes. accumulative(3): If reaction threshold type is accumulative and the times of watched operation accumulatively exceeds the limit specified by hwNqaReactThresholdAccumNum, an action specified in hwNqaReactActionType is generated when hwNqaReactCurrentStatus changes. If reaction threshold type is not configured, the value of this object is 'invalid'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER invalid(0), average(1), consecutive(2), accumulative(3)  

hwNqaReactThresholdConsecNum 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.8
This object defines a consecutive threshold limit. The value is zero when hwNqaReactThresholdType is not 'consecutive'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaReactThresholdAccumNum 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.9
This object defines an accumulative threshold limit. The value is zero when the hwNqaReactThresholdType is not 'accumulative'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

hwNqaReactActionType 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.10
Specifies the type of reaction to generate if the specified violation type occurs for the monitored element: none - No reaction is generated trapOnly - A trap is generated triggerOnly - All trigger actions defined for this entry are generated trapAndTrigger - Both a trap and all trigger actions are generated
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), trapOnly(1), triggerOnly(2), trapAndTrigger(3)  

hwNqaReactCurrentStatus 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.11
Specifies the current status of this reaction entry: invalid - Specifies the reaction entry status is uncertain. overThreshold - Specifies the reaction entry has met the hwNqaReactThresholdType and the threshold value. belowThreshold - Specifies the reaction entry has disobeyed the hwNqaReactThresholdType and the threshold value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), overThreshold(2), belowThreshold(3)  

hwNqaReactRowStatus 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.12
This object allows entries to be created and deleted in the hwNqaReactionTable. Creation of an entry in this table results in a new set of reaction configurations which take effect immediately. Deletion of an entry in this table results in corresponding reaction configurations are being deleted and stop taking effect.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwNqaReactCheckedNum 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.13
The number of checked element samples that are monitored.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaReactThresholdNum 1.3.6.1.4.1.43.45.1.5.25.28.1.13.1.14
The number of checked element samples that are over threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwNqaStatisticsReactionTable 1.3.6.1.4.1.43.45.1.5.25.28.1.14
A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwNqaStatisticsReactionEntry

hwNqaStatisticsReactionEntry 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1
Defines an entry in the hwNqaStatisticsReactionTable. The first two index elements identify the pingCtlEntry that a hwNqaReactItemIndex belongs to. The third index element identifies an entry in the hwNqaStatisticsResultsTable. The forth index element selects a single reaction.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwNqaStatisticsReactionEntry  

hwNqaStatReactOwnerIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1.1
The first index of hwNqaStatisticsReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

hwNqaStatReactTestName 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1.2
The second index of hwNqaStatisticsReactionTable, it is the same as pingCtlTestName in pingCtlTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

hwNqaStatReactIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1.3
The third index of hwNqaStatisticsReactionTable. An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hwNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwNqaStatReactItemIndex 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1.4
The forth index of hwNqaStatisticsReactionTable, it definitely identifies one of the reaction configurations for a test
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwNqaStatReactCheckedNum 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1.5
The number of checked element samples that are monitored.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaStatReactThresholdNum 1.3.6.1.4.1.43.45.1.5.25.28.1.14.1.6
The number of checked element samples that are over threshold.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwNqaNotifications 1.3.6.1.4.1.43.45.1.5.25.28.3
OBJECT IDENTIFIER    

hwNqaProbeTimeOverThreshold 1.3.6.1.4.1.43.45.1.5.25.28.3.1
It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. Probe time(equals to RTT for some type of tests) is not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit. 2. The probe time is accumulatively not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit for a number of times specified in hwNqaReactThresholdAccumNum. 3. The probe time is consecutively in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit for a number of times specified in hwNqaReactThresholdConsecNum. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hwNqajitter.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaJitterRTTOverThreshold 1.3.6.1.4.1.43.45.1.5.25.28.3.2
It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average NQA round-trip-time (RTT) of jitter packets is not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit. 2. The RTT of jitter packets is accumulatively not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit for a number of times specified in hwNqaReactThresholdAccumNum in one test. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hwNqajitter.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaProbeFailure 1.3.6.1.4.1.43.45.1.5.25.28.3.3
It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the probe test accumulatively failed for a number of times specified in hwNqaReactThresholdAccumNum in one test while the value of hwNqaReactThresholdType is 'accumulative'. 2. When the probe test consecutively failed for a number of times specified in hwNqaReactThresholdConsecNum in one test while the value of hwNqaReactThresholdType is 'consecutive'. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hwNqajitter.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaJitterPacketLoss 1.3.6.1.4.1.43.45.1.5.25.28.3.4
It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the jitter packets accumulatively lost for a number of times specified in hwNqaReactThresholdAccumNum in one test while the value of hwNqaReactThresholdType is 'accumulative'. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hwNqajitter.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaJitterSDOverThreshold 1.3.6.1.4.1.43.45.1.5.25.28.3.5
The SD means the jitter values from source to destination. It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of SD in one jitter test is not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit and the hwNqaReactThresholdType is specified as 'average' type. 2. The average of SD in one jitter test is accumulatively not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit for a number of times specified in hwNqaReactThresholdAccumNum and the hwNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hwNqajitter.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaJitterDSOverThreshold 1.3.6.1.4.1.43.45.1.5.25.28.3.6
The DS means the jitter values from destination to source. It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of DS in one jitter test is not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit and the hwNqaReactThresholdType is specified as 'average' type. 2. The average of DS in one jitter test is accumulatively not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit for a number of times specified in hwNqaReactThresholdAccumNum and the hwNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hwNqajitter.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaICPIFOverThreshold 1.3.6.1.4.1.43.45.1.5.25.28.3.7
It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the ICPIF value in one jitter test is not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hwNqajitter and hwNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwNqaMOSOverThreshold 1.3.6.1.4.1.43.45.1.5.25.28.3.8
It is generated when the value of hwNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the MOS value in one jitter test is not in the range hwNqaReactThresholdLowerLimit through hwNqaReactThresholdUpperLimit. This notification is valid only when hwNqaReactActionType is 'trapOnly' or 'trapAndTrigger' , pingCtlType of the test is hwNqajitter and hwNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
Status: current Access: read-only
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor