A3COM-HUAWEI-MPLS-LDP-MIB

File: A3COM-HUAWEI-MPLS-LDP-MIB.mib (75345 bytes)

Imported modules

A3COM-HUAWEI-OID-MIB SNMPv2-SMI SNMPv2-CONF
SNMPv2-TC

Imported symbols

huaweiMgmt hwMpls OBJECT-TYPE
MODULE-IDENTITY NOTIFICATION-TYPE Integer32
Counter32 Unsigned32 IpAddress
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
TEXTUAL-CONVENTION TruthValue RowStatus
TimeInterval

Defined Types

DisplayString  
OCTET STRING Size(0..255)    

PhysAddress  
OCTET STRING    

BitRate  
INTEGER    

BurstSize  
INTEGER    

MplsLsrIdentifier  
The Label Switch Router (LSR) identifier is the first 4 bytes or the IP Address component of the Label Distribution Protocol (LDP) identifier.
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

MplsLdpGenAddr  
The value of an network layer or data link layer address.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..64)  

MplsLdpIdentifier  
The LDP identifier is a six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR.
TEXTUAL-CONVENTION    
  OCTET STRING Size(6)  

AtmVpIdentifier  
The VPI value for a VPL. The value VPI=0 is not used for a VPL not associated with a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 1 to 255. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB.
TEXTUAL-CONVENTION    
  INTEGER 0..4095  

AtmVcIdentifier  
The VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB.
TEXTUAL-CONVENTION    
  INTEGER 0..65535  

AddressFamilyNumbers  
An address family. Values are defined in RFC 1700 - Assigned Numbers. All values may not be relevant in all contexts when used in this MIB, but are included for completeness.
TEXTUAL-CONVENTION    
  INTEGER other(0), ipv4(1), ipv6(2), nsap(3), hdlc(4), bbn1822(5), ieee802(6), e163(7), e164(8), f69(9), x121(10), ipx(11), appleTalk(12), decnetIV(13), banyanVines(14), e164WithNsap(15)  

MplsLabel  
Represents an MPLS label. Note that the contents of a label field are interpreted in an interface-type specific fashion. For example, the label carried in the MPLS shim header is 20 bits wide and the top 12 bits must be zero. The frame relay label can be either 10, 17 or 23 bits wide depending on the size of the DLCI field size and the top 22, 15, or 9 bits must be zero, respectively. For an ATM interface, the lowermost 16 bits are interpreted as the VCI, the next 8 bits as the VPI and the remaining bits must be zero. Also note the permissible label values are also a function of the interface type. For example, the value 3 has special semantics in the control plane for an MPLS shim header label and is not a valid label value in the datapath.
TEXTUAL-CONVENTION    
  INTEGER  

MplsTunnelIndex  
Index into mplsTunnelTable.
TEXTUAL-CONVENTION    
  INTEGER 0..65535  

HwMplsLdpLsrIncarnEntry  
SEQUENCE    
  hwMplsLdpLsrID MplsLsrIdentifier
  hwMplsLdpLsrLoopDetectionPresent TruthValue
  hwMplsLdpLsrLoopDetectionAdminStatus INTEGER
  hwMplsLdpLsrPathVectorLimit INTEGER
  hwMplsLdpLsrHopCountLimit INTEGER
  hwMplsLdpLsrLoopPreventionPresent TruthValue
  hwMplsLdpLsrLoopPreventionAdminStatus INTEGER
  hwMplsLdpLsrLabelRetentionMode INTEGER
  hwMplsLdpLsrIncarnID INTEGER
  hwMplsLdpLsrMaxLdpEntities INTEGER
  hwMplsLdpLsrMaxLocalPeers INTEGER
  hwMplsLdpLsrMaxRemotePeers INTEGER
  hwMplsLdpLsrMaxIfaces INTEGER
  hwMplsLdpLsrMaxLsps INTEGER
  hwMplsLdpLsrMaxCrlspTnls INTEGER
  hwMplsLdpLsrMaxErhopPerCrlspTnl INTEGER
  hwMplsLdpLsrRowStatus RowStatus
  hwMplsLdpLsrMaxVcmCapability INTEGER
  hwMplsLdpLsrVcmPathVecInAllLblMapPresent TruthValue
  hwMplsLdpLsrRequestRetrytimerValue INTEGER
  hwMplsLdpLsrNumOfRequestRetryAttempts INTEGER

HwMplsLdpEntityEntry  
SEQUENCE    
  hwMplsLdpEntityID MplsLdpIdentifier
  hwMplsLdpEntityLabelSpaceType INTEGER
  hwMplsLdpEntityDefVpi AtmVpIdentifier
  hwMplsLdpEntityDefVci AtmVcIdentifier
  hwMplsLdpEntityUnlabTrafVpi AtmVpIdentifier
  hwMplsLdpEntityUnlabTrafVci AtmVcIdentifier
  hwMplsLdpEntityMergeCapability INTEGER
  hwMplsLdpEntityVcDirectionality INTEGER
  hwMplsLdpEntityWellKnownDiscoveryPort INTEGER
  hwMplsLdpEntityMtu INTEGER
  hwMplsLdpEntityKeepAliveHoldTimer INTEGER
  hwMplsLdpEntityFailedInitSessionThreshold INTEGER
  hwMplsLdpEntityLabelDistributionMethod INTEGER
  hwMplsLdpEntityLabelAllocationMethod INTEGER
  hwMplsLdpEntityHelloHoldTimer INTEGER
  hwMplsLdpEntityRowStatus RowStatus

HwMplsLdpEntityIfEntry  
SEQUENCE    
  hwMplsLdpEntityIfIndex Unsigned32
  hwMplsLdpEntityIfIpv4Address IpAddress
  hwMplsLdpEntityIfRowStatus RowStatus

HwMplsLdpEntityConfAtmLabelRangeEntry  
SEQUENCE    
  hwMplsLdpEntityConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier
  hwMplsLdpEntityConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier
  hwMplsLdpEntityConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier
  hwMplsLdpEntityConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier
  hwMplsLdpEntityConfAtmLabelRangeRowStatus RowStatus

HwMplsLdpEntityStatsEntry  
SEQUENCE    
  hwMplsLdpAttemptedSessions Counter32

HwMplsLdpPeerEntry  
SEQUENCE    
  hwMplsLdpPeerIndex Unsigned32
  hwMplsLdpPeerID MplsLdpIdentifier
  hwMplsLdpPeerInternetworkAddrType AddressFamilyNumbers
  hwMplsLdpPeerInternetworkAddr MplsLdpGenAddr
  hwMplsLdpPeerDefaultMtu INTEGER
  hwMplsLdpPeerKeepAliveHoldTimer INTEGER
  hwMplsLdpPeerLabelDistributionMethod INTEGER
  hwMplsLdpPeerType INTEGER
  hwMplsLdpPeerRowStatus RowStatus

HwMplsLdpPeerConfAtmLabelRangeEntry  
SEQUENCE    
  hwMplsLdpPeerConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier
  hwMplsLdpPeerConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier
  hwMplsLdpPeerConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier
  hwMplsLdpPeerConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier

HwMplsLdpSessionEntry  
SEQUENCE    
  hwMplsLdpSessionIndex Unsigned32
  hwMplsLdpSessionID MplsLdpIdentifier
  hwMplsLdpSessionProtocolVersion INTEGER
  hwMplsLdpSessionKeepAliveHoldTimeRemaining TimeInterval
  hwMplsLdpSessionRole INTEGER
  hwMplsLdpSessionState INTEGER
  hwMplsLdpSessionAtmLabelRangeLowerBoundVPI AtmVpIdentifier
  hwMplsLdpSessionAtmLabelRangeLowerBoundVCI AtmVcIdentifier
  hwMplsLdpSessionAtmLabelRangeUpperBoundVPI AtmVpIdentifier
  hwMplsLdpSessionAtmLabelRangeUpperBoundVCI AtmVcIdentifier

HwMplsLdpHelloAdjacencyEntry  
SEQUENCE    
  hwMplsLdpHelloAdjacencyIndex Unsigned32
  hwMplsLdpHelloAdjacencyHoldTimeRemaining TimeInterval

HwMplsLdpCrlspTnlEntry  
SEQUENCE    
  hwMplsLdpCrlspTnlIndex MplsTunnelIndex
  hwMplsLdpCrlspTnlName DisplayString
  hwMplsLdpCrlspTnlDirection INTEGER
  hwMplsLdpCrlspTnlSignallingProto INTEGER
  hwMplsLdpCrlspTnlSetupPrio INTEGER
  hwMplsLdpCrlspTnlHoldingPrio INTEGER
  hwMplsLdpCrlspTnlPeakDataRate BitRate
  hwMplsLdpCrlspTnlPeakBurstSize BurstSize
  hwMplsLdpCrlspTnlCommittedDataRate BitRate
  hwMplsLdpCrlspTnlCommittedBurstSize BurstSize
  hwMplsLdpCrlspTnlExcessBurstSize BurstSize
  hwMplsLdpCrlspTnlIsPinned TruthValue
  hwMplsLdpCrlspTnlFrequency INTEGER
  hwMplsLdpCrlspTnlWeight INTEGER
  hwMplsLdpCrlspTnlRowStatus RowStatus

HwMplsLdpCrlspErHopEntry  
SEQUENCE    
  hwMplsLdpCrlspErHopIndex INTEGER
  hwMplsLdpCrlspErHopAddrType INTEGER
  hwMplsLdpCrlspErHopIpv4Addr IpAddress
  hwMplsLdpCrlspErHopIpv4PrefixLen INTEGER
  hwMplsLdpCrlspErHopStrictOrLoose INTEGER
  hwMplsLdpCrlspErHopRowStatus RowStatus

Defined Values

hwMplsLdp 1.3.6.1.4.1.43.45.1.5.12.2
All rights reserved
MODULE-IDENTITY    

hwMplsLdpObjects 1.3.6.1.4.1.43.45.1.5.12.2.1
OBJECT IDENTIFIER    

hwMplsLdpNotifications 1.3.6.1.4.1.43.45.1.5.12.2.2
OBJECT IDENTIFIER    

hwMplsLdpLsrObjects 1.3.6.1.4.1.43.45.1.5.12.2.1.1
OBJECT IDENTIFIER    

hwMplsLdpEntityObjects 1.3.6.1.4.1.43.45.1.5.12.2.1.2
OBJECT IDENTIFIER    

hwMplsLdpPeerObjects 1.3.6.1.4.1.43.45.1.5.12.2.1.3
OBJECT IDENTIFIER    

hwMplsLdpSessionObjects 1.3.6.1.4.1.43.45.1.5.12.2.1.4
OBJECT IDENTIFIER    

hwMplsLdpHelloAdjacencyObjects 1.3.6.1.4.1.43.45.1.5.12.2.1.5
OBJECT IDENTIFIER    

hwMplsLdpCrlspTnlObjects 1.3.6.1.4.1.43.45.1.5.12.2.1.6
OBJECT IDENTIFIER    

hwMplsLdpLsrIncarnTable 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1
HuaweiMPLS provides support for multiple incarnations of the MPLS Stack in a target. The LSR defined in the standard MIB is treated as an incarnation in this MIB. Using a local policy the Network administrator must group the LDP Entities that should be placed in an incarnation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpLsrIncarnEntry

hwMplsLdpLsrIncarnEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1
An entry in this table represents an LSR incarnation. All the entries in this table are created initially when the LDP is initiated. The row status of each entry will be in 'notInService' state initially. The row status must be set to 'active' after the necessary configurations are complete with respect to an incarnation. Currenlty the LSR ID of the incarnation is the only mandatory parameter that must be set before the rowStatus is set to 'active'. An LSR Incarnation Entity is uniquely indexed by its Incarnation Identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpLsrIncarnEntry  

hwMplsLdpLsrID 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.1
The LSR's Identifier.
Status: current Access: read-write
OBJECT-TYPE    
  MplsLsrIdentifier  

hwMplsLdpLsrLoopDetectionPresent 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.2
A indication of whether this LSR supports loop detection. A value of 'true' indicates this LSR does support loop detection. A value of 'false' indicates this LSR does not support loop detection.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwMplsLdpLsrLoopDetectionAdminStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.3
To enable loop detection the value of this object should be 'enabled(1)'. Otherwise, to turn off loop detection, set this value to 'disabled(2)'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwMplsLdpLsrPathVectorLimit 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.4
This object only has meaning if hwMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit of path vectors which this LSR uses to treat the message as if it had traversed a loop.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrHopCountLimit 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.5
This object only has meaning if hwMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit on the Hop Count which this LSR uses to treat the message as if it had traversed a loop.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrLoopPreventionPresent 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.6
A indication of whether this LSR supports loop prevention. A value of 'true' indicates this LSR does support loop prevention. A value of 'false' indicates this LSR does not support loop prevention. Current release of HuaweiMPLS does not provide support to assign this MIB object with a value 'true'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hwMplsLdpLsrLoopPreventionAdminStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.7
To enable loop prevention the value of this object should be 'enabled(1)'. Otherwise, to turn off loop prevention, set this value to 'disabled(2)'. Current release of HuaweiMPLS does not provide support to assign this MIB object with a value 'enabled'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hwMplsLdpLsrLabelRetentionMode 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.8
The LSR can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be used to forward packets, i.e. if label came from a valid next hop. If the value of this object is liberal(2) then all advertized label mappings are retained whether they are from a valid next hop or not. Current release of HuaweiMPLS does not provide support to assign this MIB object with a value 'liberal'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER conservative(1), liberal(2)  

hwMplsLdpLsrIncarnID 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.9
The incarnation acts as index to all the elements in this table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrMaxLdpEntities 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.10
The maximum number of LDP entities that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

hwMplsLdpLsrMaxLocalPeers 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.11
The maximum number of Local LDP peers that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

hwMplsLdpLsrMaxRemotePeers 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.12
The maximum number of Remote LDP peers that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

hwMplsLdpLsrMaxIfaces 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.13
The maximum number of Label enabled Interfaces that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrMaxLsps 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.14
The maximum number of Label Switched Paths that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrMaxCrlspTnls 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.15
The maximum number of CRLSPs that can be supported by this Incarnation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrMaxErhopPerCrlspTnl 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.16
The maximum number of ER-Hops that can be supported in a CRLSP tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.17
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpLsrMaxVcmCapability 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.18
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrVcmPathVecInAllLblMapPresent 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.19
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hwMplsLdpLsrRequestRetrytimerValue 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.20
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpLsrNumOfRequestRetryAttempts 1.3.6.1.4.1.43.45.1.5.12.2.1.1.1.1.21
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

hwMplsLdpEntityTable 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1
This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switch Router (LSR).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpEntityEntry

hwMplsLdpEntityEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1
An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An LPD Entity is uniquely indexed by its LPD Identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpEntityEntry  

hwMplsLdpEntityID 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.1
The LDP identifier which uniquely identifies the LDP Entity. This is s six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MplsLdpIdentifier  

hwMplsLdpEntityLabelSpaceType 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.2
The type of label spaces associated with this LDP Entity. The values are 'unknown(1)' The type of label space is not known. 'perInterface(2)' The type of label space is tied to an interface. 'perPlatform(3)' The type of label space is tied to the platform.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unknown(1), perInterface(2), perPlatform(3)  

hwMplsLdpEntityDefVpi 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.3
The Default VPI value used in the label for the default VPI.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpEntityDefVci 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.4
The Default VCI value used in the label for the default VCI.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpEntityUnlabTrafVpi 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.5
VPI value of the VCC supporting unlabeled traffic.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpEntityUnlabTrafVci 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.6
VCI value of the VCC supporting unlabeled traffic.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpEntityMergeCapability 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.7
Sets the merge capability for this LDP entity. Current Release of HuaweiMPLS does not provide support for any kind of Merge.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER noMerge(0), vpMerge(1), vcMerge(2), vpVcMerge(3)  

hwMplsLdpEntityVcDirectionality 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.8
Sets the VC directionality for this LDP entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bidirectional(1), unidirectional(2)  

hwMplsLdpEntityWellKnownDiscoveryPort 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.9
The well known LDP Discovery Port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

hwMplsLdpEntityMtu 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.10
The maximum transmission unit (MTU) that was configured for this entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

hwMplsLdpEntityKeepAliveHoldTimer 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.11
The two octet value which is the proposed keep alive hold timer for this LDP Entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

hwMplsLdpEntityFailedInitSessionThreshold 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.12
When attempting to establish a session with a given Peer, the given LDP Entity should send out a notification when exceeding this threshold. A value of 0 (zero) for this object indicates that the threshold is infinity. In other words, a notification will not be sent if the value of this object is 0 (zero).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

hwMplsLdpEntityLabelDistributionMethod 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.13
For any given LDP session, the method of label distribution must be specified. Current release of HuaweiMPLS does not provide support for 'downstreamUnsolicited'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER downstreamOnDemand(1), downstreamUnsolicited(2)  

hwMplsLdpEntityLabelAllocationMethod 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.14
For any given LDP session, the method of label allocation must be specified. Label can be allocated in either ordered mode or in the independent mode.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ordered(1), independent(2)  

hwMplsLdpEntityHelloHoldTimer 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.15
The two octet value which is the proposed hello hold timer for this LDP Entity.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

hwMplsLdpEntityRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.2.1.1.16
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpEntityIfTable 1.3.6.1.4.1.43.45.1.5.12.2.1.2.2
This table contains information about the interfaces that are associated with an LDP Entity. There should be atleast one interface associated with each LDP Entity. If the LDP Entity supports 'per interface based label space' label type then, atmost one interface can be associated with the LDP entity. If the LDP Entity supports 'per platform based label space' label type then, more than one interface can be associated with the LDP Entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpEntityIfEntry

hwMplsLdpEntityIfEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.2.2.1
An entry in this table represents an Interface that is associated with a LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An interface (row in this table) can be created/deleted only when the associted LDP Entity row status has the value notInService or notReady.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpEntityIfEntry  

hwMplsLdpEntityIfIndex 1.3.6.1.4.1.43.45.1.5.12.2.1.2.2.1.1
Identifier that uniquely identifies the Interface with respect to an LDP Entity. The ifIndex value corresponds to the IfIndex value of the MIB-II
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hwMplsLdpEntityIfIpv4Address 1.3.6.1.4.1.43.45.1.5.12.2.1.2.2.1.2
The IPv4 address associated with the interface.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwMplsLdpEntityIfRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.2.2.1.3
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpEntityConfAtmLabelRangeTable 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3
The MPLS LDP Entity Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Entities. LDP Entities which use ATM must have at least one entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpEntityConfAtmLabelRangeEntry

hwMplsLdpEntityConfAtmLabelRangeEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3.1
A row in the LDP Entity Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Entity are UNIQUE and non-overlapping. For example, for a specific LDP Entity index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP EntityID and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Entity MUST include the default VPI/VCI values denoted in the LDP Entity Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpEntityConfAtmLabelRangeEntry  

hwMplsLdpEntityConfAtmLabelRangeLowerBoundVPI 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3.1.1
The minimum VPI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpEntityConfAtmLabelRangeLowerBoundVCI 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3.1.2
The minimum VCI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpEntityConfAtmLabelRangeUpperBoundVPI 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3.1.3
The maximum VPI number configured for this range.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpEntityConfAtmLabelRangeUpperBoundVCI 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3.1.4
The maximum VCI number configured for this range.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpEntityConfAtmLabelRangeRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.2.3.1.5
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpEntityStatsTable 1.3.6.1.4.1.43.45.1.5.12.2.1.2.4
This table is a read-only table which augments the MplsLdpConfEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on the LSR.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpEntityStatsEntry

hwMplsLdpEntityStatsEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.2.4.1
A row in this table contains statistical information about an LDP Entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpEntityStatsEntry  

hwMplsLdpAttemptedSessions 1.3.6.1.4.1.43.45.1.5.12.2.1.2.4.1.1
A count of the total attempted sessions for this LDP Entity.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hwMplsLdpPeerTable 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1
Information about LDP peers which have been discovered by the LDP Entities that are managed by this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpPeerEntry

hwMplsLdpPeerEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1
Information about a single Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpPeerEntry  

hwMplsLdpPeerIndex 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.1
An identifier for the LDP peer that is unique within the scope of this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hwMplsLdpPeerID 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.2
The LDP identifier of this LDP Peer.
Status: current Access: read-create
OBJECT-TYPE    
  MplsLdpIdentifier  

hwMplsLdpPeerInternetworkAddrType 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.3
The type of the internetwork layer address of this LDP peer. This object indicates how the value of hwMplsLdpPeerInternetworkAddr is to be interpreted.
Status: current Access: read-create
OBJECT-TYPE    
  AddressFamilyNumbers  

hwMplsLdpPeerInternetworkAddr 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.4
The value of the internetwork layer address of this LDP peer.
Status: current Access: read-create
OBJECT-TYPE    
  MplsLdpGenAddr  

hwMplsLdpPeerDefaultMtu 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.5
The default maximum transmission unit (MTU) of the LDP Peer.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

hwMplsLdpPeerKeepAliveHoldTimer 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.6
The two octet unsigned non zero INTEGER that indicates the number of seconds that this Peer proposes for the value of the KeepAlive Interval.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..65535  

hwMplsLdpPeerLabelDistributionMethod 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.7
For any given LDP session, the method of label distribution must be specified.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER downstreamOnDemand(1), downstreamUnsolicited(2)  

hwMplsLdpPeerType 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.8
Indicates whether a peer is a local peer or a remote peer
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

hwMplsLdpPeerRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.3.1.1.9
An object that allows entries in this table to be created and deleted using the RowStatus convention.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpPeerConfAtmLabelRangeTable 1.3.6.1.4.1.43.45.1.5.12.2.1.3.2
The MPLS LDP Peer Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Peers. LDP Peers which use ATM must have at least one entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpPeerConfAtmLabelRangeEntry

hwMplsLdpPeerConfAtmLabelRangeEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.3.2.1
A row in the LDP Peer Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Peer are UNIQUE and non-overlapping. For example, for a specific LDP Peer index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP PeerIndex and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Peer MUST include the default VPI/VCI values denoted in the LDP Peer Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpPeerConfAtmLabelRangeEntry  

hwMplsLdpPeerConfAtmLabelRangeLowerBoundVPI 1.3.6.1.4.1.43.45.1.5.12.2.1.3.2.1.1
The minimum VPI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpPeerConfAtmLabelRangeLowerBoundVCI 1.3.6.1.4.1.43.45.1.5.12.2.1.3.2.1.2
The minimum VCI number configured for this range.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpPeerConfAtmLabelRangeUpperBoundVPI 1.3.6.1.4.1.43.45.1.5.12.2.1.3.2.1.3
The maximum VPI number configured for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpPeerConfAtmLabelRangeUpperBoundVCI 1.3.6.1.4.1.43.45.1.5.12.2.1.3.2.1.4
The maximum VCI number configured for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpSessionTable 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1
A table of Sessions between the LDP Entities and LDP Peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpSessionEntry

hwMplsLdpSessionEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1
An entry in this table represents information on a single session between an LDP Entity and LDP Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpSessionEntry  

hwMplsLdpSessionIndex 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.1
An unique identifier for this entry such that it identifies a specific LDP Session.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hwMplsLdpSessionID 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.2
The LDP Session identifier.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLdpIdentifier  

hwMplsLdpSessionProtocolVersion 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.3
The version of the LDP Protocol which this session is using.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

hwMplsLdpSessionKeepAliveHoldTimeRemaining 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.4
The keep alive hold time remaining for this session.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

hwMplsLdpSessionRole 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.5
An indication of whether the LDP Entity associated with this session is acting in an 'active' role or a 'passive' role.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

hwMplsLdpSessionState 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.6
The current state of the session, all of the states 1 - 5 are based on the state machine for session negotiation behavior.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5)  

hwMplsLdpSessionAtmLabelRangeLowerBoundVPI 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.7
The minimum VPI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpSessionAtmLabelRangeLowerBoundVCI 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.8
The minimum VCI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpSessionAtmLabelRangeUpperBoundVPI 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.9
The maximum VPI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

hwMplsLdpSessionAtmLabelRangeUpperBoundVCI 1.3.6.1.4.1.43.45.1.5.12.2.1.4.1.1.10
The maximum VCI number for this range.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

hwMplsLdpHelloAdjacencyTable 1.3.6.1.4.1.43.45.1.5.12.2.1.5.1
A table of Hello Adjacencies for Sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpHelloAdjacencyEntry

hwMplsLdpHelloAdjacencyEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.5.1.1
Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpHelloAdjacencyEntry  

hwMplsLdpHelloAdjacencyIndex 1.3.6.1.4.1.43.45.1.5.12.2.1.5.1.1.1
An identifier for the adjacency.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

hwMplsLdpHelloAdjacencyHoldTimeRemaining 1.3.6.1.4.1.43.45.1.5.12.2.1.5.1.1.2
The time remaining for this Hello Adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

hwMplsLdpCrlspTnlTable 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1
The hwMplsLdpCrlspTnlTable allows new CRLSP MPLS tunnels to be created. The ER hops associated with a CRLSP tunnel are to be configured using the hwMplsLdpCrlspErHopTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpCrlspTnlEntry

hwMplsLdpCrlspTnlEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1
An entry in this table represents an CRLSP MPLS tunnel. An entry can be created by a network administrator.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpCrlspTnlEntry  

hwMplsLdpCrlspTnlIndex 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.1
Uniquely identifies this row.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MplsTunnelIndex  

hwMplsLdpCrlspTnlName 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.2
The 'canonical' name assigned to the tunnel that can be used to refer to it on the 'console' port.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

hwMplsLdpCrlspTnlDirection 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.3
Whether this tunnel is unidirectional-incoming, unidirectional-outgoing, or bidirectional.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER in(1), out(2), inOut(3)  

hwMplsLdpCrlspTnlSignallingProto 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.4
The signaling protocol, if any, that set up this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), ldp(2), rsvp(3)  

hwMplsLdpCrlspTnlSetupPrio 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.5
The setup priority of this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

hwMplsLdpCrlspTnlHoldingPrio 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.6
The holding priority for this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

hwMplsLdpCrlspTnlPeakDataRate 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.7
The peak rate - the maximum rate at which traffic will be sent on the CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BitRate  

hwMplsLdpCrlspTnlPeakBurstSize 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.8
The peak burst size - the maximum burst size of the traffic that can occur in the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BurstSize  

hwMplsLdpCrlspTnlCommittedDataRate 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.9
The committed rate - the committed rate at which traffic will be sent on the CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BitRate  

hwMplsLdpCrlspTnlCommittedBurstSize 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.10
The committed burst size - the committed burst size of the traffic that will be handled in the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BurstSize  

hwMplsLdpCrlspTnlExcessBurstSize 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.11
The Excess burst size - the excess burst size limit to be used for traffic conditioning at the ingress of the CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  BurstSize  

hwMplsLdpCrlspTnlIsPinned 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.12
Indicates whether the loose-routed hops of this tunnel are to be pinned.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

hwMplsLdpCrlspTnlFrequency 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.13
Indicates the frequency of usage of the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..2  

hwMplsLdpCrlspTnlWeight 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.14
Indicates the weight that is the established CRLSP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

hwMplsLdpCrlspTnlRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.6.1.1.15
For controlling the state of this row. The status can be set to 'active' only when atleast one ERHOP is created in the hwMplsLdpErHopTable, associated with this tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpCrlspErHopTable 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2
The hwMplsLdpCrlspErHopTable is used to indicate the hops, strict or loose, for an MPLS CRLSP tunnel defined in hwMplsLdpCrlspTnlTable. There must be atleast one entry in this table for each CRLSP tunnel that is supported in the hwMplsLdpCrlspTnlTable. The first row in the table is the first hop after the origination point of the tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpCrlspErHopEntry

hwMplsLdpCrlspErHopEntry 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1
An entry in this table represents a tunnel hop. An entry is created by a network administrator for signalled ERLSP set up by LDP or RSVP.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpCrlspErHopEntry  

hwMplsLdpCrlspErHopIndex 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1.1
Secondary index into this table identifying the particular hop.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

hwMplsLdpCrlspErHopAddrType 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1.2
Address type of this hop.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ipV4(1)  

hwMplsLdpCrlspErHopIpv4Addr 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1.3
If hwMplsLdpCrlspErHopAddrType is ipV4(1), IPv4 address of this hop. This object is not significant otherwise and should return a value of 0.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwMplsLdpCrlspErHopIpv4PrefixLen 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1.4
If hwMplsLdpCrlspErHopAddrType is ipV4(1), prefix length for this hop's IPv4 address. This object is not significant otherwise and should return a value of 0.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..32  

hwMplsLdpCrlspErHopStrictOrLoose 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1.5
Whether this is a strict or loose hop.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER strict(1), loose(2)  

hwMplsLdpCrlspErHopRowStatus 1.3.6.1.4.1.43.45.1.5.12.2.1.6.2.1.6
For creating, modifying and deleting this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwMplsLdpNotificationPrefix 1.3.6.1.4.1.43.45.1.5.12.2.2.0
OBJECT IDENTIFIER    

hwMplsLdpFailedInitSessionThresholdExceeded 1.3.6.1.4.1.43.45.1.5.12.2.2.0.1
This notification is generated whenever the value of hwMplsLdpEntityFailedInitSessionThreshold is exceeded.
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpCrlspTunnelUp 1.3.6.1.4.1.43.45.1.5.12.2.2.0.2
This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Label mapping message from the downstream LSR for the LAbel request sent for the CRLSP tunnel.
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpCrlspTunnelDown 1.3.6.1.4.1.43.45.1.5.12.2.2.0.3
This notification is generated when a CRLSP Row status is modified to destroy the CRLSP tunnel. - due to pre-emption etc.,
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpCrlspTunnelSetupFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.4
This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Nak message from the downstream LSR for the Label request sent for the CRLSP tunnel. This can occur due to improper ER hop values being set, or Traffic resources not available etc.,
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpIncarnUpEventFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.11
This notification is generated by LDP to notify the Incarnation UP Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpIncarnDownEventFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.12
This notification is generated by LDP to notify the Incarnation DOWN Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpEntityUpEventFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.13
This notification is generated by LDP to notify the ENTITY UP Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpEntityDownEventFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.14
This notification is generated by LDP to notify the ENTITY DOWN Event failure
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpSessionUpEventFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.15
Generation of this trap occurs when the value of 'hwMplsLdpSessionState' enters the 'operational(5)' state.
Status: current Access: read-create
NOTIFICATION-TYPE    

hwMplsLdpSessionDownEventFailure 1.3.6.1.4.1.43.45.1.5.12.2.2.0.16
Generation of this trap occurs when the value of 'hwMplsLdpSessionState' leaves the 'operational(5)' state.
Status: current Access: read-create
NOTIFICATION-TYPE