A3COM-HUAWEI-DOT11-WLANEXT-MIB

File: A3COM-HUAWEI-DOT11-WLANEXT-MIB.mib (11200 bytes)

Imported modules

SNMPv2-SMI A3COM-HUAWEI-DOT11-REF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Counter32 h3cDot11 H3cDot11ObjectIDType
H3cDot11RadioScopeType H3cDot11QosAcType

Defined Types

H3cDot11RFSignalStatisEntry  
SEQUENCE    
  h3cDot11RFAPID H3cDot11ObjectIDType
  h3cDot11RFRadioID H3cDot11RadioScopeType
  h3cDot11RFSignalStatisInterv Integer32
  h3cDot11RFAverageSignalStrength Integer32
  h3cDot11RFMaxSignalStrength Integer32
  h3cDot11RFMinSignalStrength Integer32

H3cDot11QosStatisEntry  
SEQUENCE    
  h3cDot11QosAPID H3cDot11ObjectIDType
  h3cDot11QosRadioID H3cDot11RadioScopeType
  h3cDot11QosAverageQueLen Integer32
  h3cDot11QosDropFrameRatio Integer32
  h3cDot11QosAverageDataRate Integer32

H3cDot11QosAcStatisEntry  
SEQUENCE    
  h3cDot11QosAcType H3cDot11QosAcType
  h3cDot11AcDropFrameCnt Counter32

Defined Values

h3cDot11WLANEXT 1.3.6.1.4.1.43.45.1.10.2.75.7
This MIB provides more information for WLAN network. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. IEEE 802.11e Standard to define the MAC procedures to support LAN applications with Quality of Service (QoS) requirements, including the transport of voice, audio and video over IEEE 802.11 wireless LANs. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Radio The chip set to receive and send wireless signal. Fat AP Applied in the home, SOHO and so on, and it could independently work without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. Basic Service Set The IEEE 802.11 BSS of an AP comprises of the stations directly associating with the AP. It will be identified by BSSID.
MODULE-IDENTITY    

h3cDot11RFGroup 1.3.6.1.4.1.43.45.1.10.2.75.7.1
OBJECT IDENTIFIER    

h3cDot11QosGroup 1.3.6.1.4.1.43.45.1.10.2.75.7.2
OBJECT IDENTIFIER    

h3cDot11RFSignalStatisTable 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1
The table will describe statistic information of signal strength for AP radio.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cDot11RFSignalStatisEntry

h3cDot11RFSignalStatisEntry 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1
Each entry contains the signal of each signal strength information of a specific AP.
OBJECT-TYPE    
  H3cDot11RFSignalStatisEntry  

h3cDot11RFAPID 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.1
To identify each AP, and AP is running status.
OBJECT-TYPE    
  H3cDot11ObjectIDType  

h3cDot11RFRadioID 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.2
Represents each radio.
OBJECT-TYPE    
  H3cDot11RadioScopeType  

h3cDot11RFSignalStatisInterv 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.3
Represents the interval of statistic.
OBJECT-TYPE    
  Integer32  

h3cDot11RFAverageSignalStrength 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.4
Represents the average value of signal strength for stations on a specific radio.
OBJECT-TYPE    
  Integer32  

h3cDot11RFMaxSignalStrength 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.5
Represents the maximum value of signal strength for stations on a specific radio.
OBJECT-TYPE    
  Integer32  

h3cDot11RFMinSignalStrength 1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.6
Represents the minimum value of signal strength for stations on a specific radio.
OBJECT-TYPE    
  Integer32  

h3cDot11QosStatisTable 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1
The table defines the attributes for the Qos feature of radio.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cDot11QosStatisEntry

h3cDot11QosStatisEntry 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1
Each entry contains information of the Qos attribute of each radio.
OBJECT-TYPE    
  H3cDot11QosStatisEntry  

h3cDot11QosAPID 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.1
To uniquely identify a AP in running status.
OBJECT-TYPE    
  H3cDot11ObjectIDType  

h3cDot11QosRadioID 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.2
Represents each radio.
OBJECT-TYPE    
  H3cDot11RadioScopeType  

h3cDot11QosAverageQueLen 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.3
The average frame numbers to be sent out in the queue.
OBJECT-TYPE    
  Integer32  

h3cDot11QosDropFrameRatio 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.4
The ratio of dropped frames in a minute because of full queue.
OBJECT-TYPE    
  Integer32  

h3cDot11QosAverageDataRate 1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.5
The average transmit data rate of radio.
OBJECT-TYPE    
  Integer32  

h3cDot11QosAcStatisTable 1.3.6.1.4.1.43.45.1.10.2.75.7.2.2
The table defines the parameters for Qos access category.
OBJECT-TYPE    
  SEQUENCE OF  
    H3cDot11QosAcStatisEntry

h3cDot11QosAcStatisEntry 1.3.6.1.4.1.43.45.1.10.2.75.7.2.2.1
Each entry contains information of each Qos access category.
OBJECT-TYPE    
  H3cDot11QosAcStatisEntry  

h3cDot11QosAcType 1.3.6.1.4.1.43.45.1.10.2.75.7.2.2.1.1
The access category type.
OBJECT-TYPE    
  H3cDot11QosAcType  

h3cDot11AcDropFrameCnt 1.3.6.1.4.1.43.45.1.10.2.75.7.2.2.1.2
The number of dropped frames in a minute for one specific access category because of full queue.
OBJECT-TYPE    
  Counter32